Scotts Spreader 3000 Users Manual

3000 to the manual ddd0ae81-be7c-410c-858b-d067e057edf1

2015-02-05

: Scotts Scotts-Scotts-Spreader-3000-Users-Manual-359029 scotts-scotts-spreader-3000-users-manual-359029 scotts pdf

Open the PDF directly: View PDF PDF.
Page Count: 2

DownloadScotts Scotts-Scotts-Spreader-3000-Users-Manual-  Scotts-scotts-spreader-3000-users-manual
Open PDF In BrowserView PDF
Calibration

SHUTOFF
BAR

Your AccuGreen 3000 spreader was calibrated at
the factory. You may check the calibration as follows:
1. Adjust the micrometer setting to 6.
2. Squeeze the trigger against the handle.
3. The front edge of the shutoff bar should be
flush with the calibration line engraved on the bottom of the hopper.
4. To adjust alignment, use a small wrench to turn the
black calibration screw at the lower end of the control
wire leading from the micrometer rate setting barrel.
®

TM

CALIBRATION
LINE

Spend a few minutes on
maintenance after each use

DROP SPREADER

Ready to use!
No assembly!

1. Never leave product in the spreader. Pour leftover material
2.

back into the package and seal the package tightly.
After each use, wash thoroughly to remove all material
clinging to the spreader. Hot water may be required
at times to remove stubborn residue. Allow the
spreader to dry thoroughly in the sun.

The Scotts Difference

®

3. Store your spreader in a clean dry place.
NOTE: This unit does not require lubrication.

Thank you
for purchasing a Scotts® AccuGreen® 3000 spreader. The Scotts Company
introduced the first home lawn spreader in 1946 and has continued to offer
superior quality that translates into more accurate application, a betterlooking lawn, and a longer-lasting, more durable spreader. The lawn care
industry’s most extensive research, design, and testing have gone into
making the AccuGreen series spreaders the most accurate in their class. With
its durable rustproof hopper, the AccuGreen® 3000TM spreader is guaranteed
to give you great results — now
and for many years to come.
Questions, Comments, Information
TM

“Lawn Success Made Easy” ™
Visit Scotts’ website at
www.scottslawn.com

ACCUGREEN 3000

73730

Scotts No-Quibble
Guarantee®
If for any reason you, the consumer, are not satisfied
after using this product, you are entitled to get your
money back. Simply send us evidence of purchase
and we will mail you a refund check promptly.

®

01-AG3000 Printed in USA

The Scotts Company
14111 Scottslawn Rd.
Marysville, Ohio 43041

Printed on Recyled Paper

STRIP IN UPC CODE
0 32247 73730 2

PROOF OF PURCHASE
©2001, The Scotts Company. World rights reserved.

125001212

Call Scotts’ toll- free
Consumer Helpline:
1-800-543-TURF

• Number 1 selling drop spreader nationwide
• Cushioned, U-shaped handle with positivelocking on/off control
• Easy-to-read precision micrometer rate setting
for increased accuracy
• Hopper holds 10,000-square-feet (930 sq.
meter) of Scotts fertilizer
• Heavy duty frame
• 22 inch (56 cm) spread pattern for maximum
coverage
• Rustproof hopper, agitator
and polymer components
• Easy-rolling 12-inch (30 cm)
wheels provide high ground
clearance to help prevent clogging
• Scotts No-Quibble Guarantee®
• Made in the U.S.A.
INSTRUCTIONS INSIDE —SAVE FOR FUTURE REFERENCE

To use your new AccuGreen 3000 spreader:
®

Set up the stand and handle

5. If the lawn product you purchased does not give the setting for
your Scotts® AccuGreen® spreader, you can test for the proper
setting.
Empty the number of pounds the manufacturer recommends for
1,000 square feet (90 sq. meters) into the spreader. Adjust the
spreader to a very low setting and spread product over a 1,000square- foot (90 sq. meter) area (50 by 20 feet, 33 by 30 feet, 15 by 6
meters, 10 by 9 meters, or equivalent). Adjust the setting upward
after judging how much product has been applied to the test
area. Remember: it is safer to under-apply with the test and
increase setting later as needed. Some fertilizers can burn your
lawn if over- applied.

1. Lay the spreader down so that it rests on the
front of the hopper. Lift the stand and brace,
then spread the sides of the brace and insert
the ends into the holes in the stand.
2. Place the spreader upright on its wheels. Raise
the top half of the handle to the upright position
and tighten the wing nuts by hand. With our
patented locking wing nuts, no tools are needed.
NOTE: Reverse steps 1 and 2 for convenient, compact
storage of your AccuGreen 3000 spreader.
®

TM

Set the spreading rate before
you begin

Follow these application tips for
guaranteed results

For best results, use a Scotts Lawn Fertilizer
or Grass Seed Product.

1.

2.
3.

4.

First check the back of your Scotts® product
package for the proper rate setting number
under the heading “Scotts Drop.” Some
other lawn product manufacturers provide
settings for Scotts drop spreaders, but using
TRIGGER
CONTROL
Scotts products will assure the best possible
results. (If you already purchased a product which
does not provide a setting for Scotts drop
spreaders, you can use the method described
in #5.)
Be sure spreader is turned off (trigger control
is away from the handle) by rocking the lock
lever(A).
Always fill the spreader on the driveway or
sidewalk — not on the lawn. Turn the
micrometer rate setting barrel (B) until the proper
number is visible in the window.
Ready? Start walking, then squeeze the trigger
to open the spreader (C). You may lock the
spreader in the “on” position by rocking the
lock mechanism into place.
Always push the spreader when applying
product. When pulled backward while
open, the spreader may apply an excessive
amount and damage the lawn.

TM

1.

LOCK
LEVER

(A)

2.

(B)

3.

If your lawn is rectangular, apply product the
longest direction. Apply two header strips across
each end for a turning area. Do not leave the
spreader open as you turn — shut it off as you
reach the end of a strip, then open it as you
begin the next one.
If there are trees in the lawn, shut off the spreader just
before getting to the trunk, then
move to the opposite side and continue with the
spreading pattern.
If your lawn is an irregular shape, apply a header strip completely around it. Then apply product back and forth in the longest direction,
shutting off the spreader when you reach the
header strip.
Avoid “skips” or missed streaks. This means
slightly overlapping each strip over the edge
of the previous strip by lining up the arrow
on the hopper with the wheel track from the
previous row. Do not use the wheel for
alignment.
TIP: Applying a slight amount of water to
ARROW
your lawn prior to using the spreader will
WHEEL
TRACK FROM
highlight your rows, making consistent
PREVIOUS ROW
application easier.
ARROW

(C)

WHEEL TRACK FROM
PREVIOUS ROW



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2001:03:28 11:04:48Z
Modify Date                     : 2004:11:11 16:05:31-05:00
Page Count                      : 2
Has XFA                         : No
Creation Date                   : 2001:03:28 11:04:48Z
Producer                        : Acrobat Distiller 4.0 for Macintosh
Mod Date                        : 2004:11:11 16:05:31-05:00
Metadata Date                   : 2004:11:11 16:05:31-05:00
EXIF Metadata provided by EXIF.tools

Navigation menu