Sears 917 25254 Users Manual

917252540 917252540 CRAFTSMAN LAWN TRACTOR - Manuals and Guides L0809027 View the owners manual for your CRAFTSMAN LAWN TRACTOR #917252540. Home:Lawn & Garden Parts:Craftsman Parts:Craftsman LAWN TRACTOR Manual

CRAFTSMAN Lawn, Tractor Manual L0809027 CRAFTSMAN Lawn, Tractor Owner's Manual, CRAFTSMAN Lawn, Tractor installation guides

!! Sears-21 Sears Lawn Mower Manuals - Lawn Mower Manuals – The Best Lawn Mower Manuals Collection

917.25254 to the manual a9152932-7f39-4c0e-92e0-e4c1bff5f37e

2015-02-05

: Sears Sears-917-25254-Users-Manual-399131 sears-917-25254-users-manual-399131 sears pdf

Open the PDF directly: View PDF PDF.
Page Count: 56

DownloadSears Sears-917-25254-Users-Manual- Sears-917-25254-users-manual
Open PDF In BrowserView PDF
_9

®

MODEL

917.252540

OWNER'S

° Assembly
° Operation
o Customer Responsibilities
o Service and Adjustments
o Repair Parts

CAUTION:

Read and follow

all safety

rules and instructions

MANUAL

Convertible

before

operating

this equipment.

FOR CONSUMER ASSISTANCE HOT LINE, CALL THIS TOLL FREE NUMBER: 1-800-659-5917

SAFETY
Practices RULES
for Ride-On

Safe Operation

Mowers

IMPORTANT:
THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING
HANDS AND FEET AND THROWING OBJECTS
FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR DEATH.
1.

GENERAL

•

Read, understand, and follow al! instructions in the manual
and on the machine before starting
Only allow responsible adults, who are familiar with the
instructions, to operate the machine.
Clear the area of objects such as rocks, toys, wire, etc,
which could be picked up and thrown by the blade.
Be sure the area is clear of other people before mowing, Stop
machine if anyone enters the area°
Never carry passengers.
Do not mow in reverse unless absolutely necessary. Always
look down and behind before and while backing.
Be aware of the mower discharge direction and do not point
it at anyone. Do not operate the mower •without either the
entire grass catcher or the guard in place.,
Slow down before turning
Never leave a running machine unattended. Always turn off
blades, set parking brake, stop engine, and remove keys
before dismounting.
Turn off blades when not mowing.
Stop engine before removing grass catcher or' unclogging
chute°
Mow only in daylight or good artificial light..
Do not operate the machine while under the influence of
alcohol or drugs,_
Watch for traffic when operating near or crossing roadways.,
Use extra care when loading or' unloading the machine into
a trailer or truck.,

•
•
•
•
•

•
•

°
•
°
°
•
•
II.

SLOPE

OPERATION

III. CHILDREN
Tragic accidents can occur if the operator is not alert to the
presence
of children.
Children are often attracted to the
machine
and the mowing activity_
Never assume that
children will remain where you last saw them.,
•
Keep children out of the mowing area and under the watchful
care of another responsible adult,
•
Be alert and turn machine off if children enter the area.
°

Before and when backing, look behind and down for small
children.

•

Never carry children. They may fall off and be seriously
injured or interfere with safe machine operation.
Never allow children to operate the machine.
Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision,

•
•
IV.

SERVICE

•

Use extra care in handling gasoline and other fuels They are
flammable and vapors are explosive
Use only an approved container.
Never remove gas cap or add fuel with the engine
running_ Allow engine to cool before refueling Do not
smoke..
Never refuel the machine indoors.
Never store the machine or fuel container inside where
there is an open flame, such as a water heater.
Never run a machine inside a closed area
Keep nuts and bolts, especially blade attachment bolls, tight
and keep equipment in good condition..
Never tamper with safety devices..
Check their proper
operation regularly
Keep machine free of grass, leaves, or other debris build-upo
Clean oil or fuel spillage,
Allow machine to coo! before
storing_
Stop and inspect the equipment if you strike an object.
Repair, if necessary, before restarting
Never make adjustments or repairs with the engine running
Grass catcher components are subject to wear, damage, and
deterioration, which could expose moving parts or allow
objects to be thrown. Frequently check components and
replace with manufacturer's recommended pads, when necessary.
Mower blades are sharp and can cut. Wrap the blade(s) or
wear gloves, and use extra caution when servicing them.
Check brake operation frequently. Adjust and service as
required..

•
•

OPERATION
°

Slopes are a major' factor

related to loss-of-control
and
tipover accidents, which can result in severe injury or death.
All slopes require extra caution.
If you cannot back up the
slope or if you feel uneasy on it, do not mow it.

•

•

DO:
.
Mow up and down slopes, not across.
°
Remove obstacles such as rocks, tree limbs, etc.
o
Watch for holes, ruts, or bumps_ Uneven terrain could
overturn the machine° Tall grass can hide obstactes_
o
Use s_owspeed. Choose a low gear so that you will not have
to stop or shift while on the slope.
o
Follow the manufacturer's
recommendations
for wheel
weights or counterweights to improve stability
o
Use extra care with grass catchers or other attachments.
These can change the stability of the machine,
o
Keep all movement on the slopes slowand gradual, Do not
make sudden changes in speed or direction
o
Avoid starting or stopping on a slope, ff tires lose traction,
disengage the blades and proceed slowly straight down the
slope,

•
•

•
•

................ Look

for thi's'""symboi"to poi'nt

out iT-

CAUTIONt!!
ALERT!!!It means
YOUR
portant
safetyBECOME
precautions.
SAFETY IS INVOLVED.

DO NOT:
.
o

o
.
o

....

Do not turn on slopes unless necessary, and then, turn slowly
and gradually downhill, if possible
Do not mow near drop-offs, ditches, or embankments. The
mower could suddenly turn over if a wheel is over the edge
of a cliff or ditch, or if an edge caves in.
Do not mow on wet grass.. Reduced traction could cause
sliding.,
Do not try to stabilize the machine by putting your foot on the
ground_
Do not use grass catcher on steep slopes.

CAUTION:
_

Always disconnect

spark plug

spark plug in order to prevent accidental
wireandplacewirewhereitcannotcontact
starting when setting up, transporting,
adjusting or making repairs.
.........

& WARNING
The engine exhaust from this product contains chemicals known to the State of California to cause cancer,
reproductive
harm.

2

birth

defects,

or other

I
I
I
|

PRODUCT

CONGRATULATIONS
on your purchase of a Sears
Tractor. It has been designed, engineered and manufactured to give you the best possible dependability and
performance.
Should you experience any problem you cannot easily
remedy, please contact your nearest Sears Authorized
Service CentedDepartment.
We have competent, welltrained technicians and the proper tools to service or repair
this tractor.
Please read and retain this manual.. The instructions will
enable you to assemble and maintain your tractor properly.
Always observe the "SAFETY RULES'L
MODEL
NUMBER

917252540

SPECRFICATIONS

HORSEPOWER:

14.5

GASOLINE CAPACITY
AND TYPE:

5 QUARTS
UNLEADED

OIL TYPE (API-SF/SG):

SAE 10W30 (above 32°F)
SAE 5W-30 (below 32°F)

OIL CAPACITY:

W/FILTER:
W/O FILTER:

SPARK PLUG:
(GAP: .040")

CHAMPION

VALVE CLEARANCE:

NOT ADJUSTABLE

GROUND SPEED (MPH):

FORWARD:
1st
2nd
3rd
4th
5th
6th
REVERSE:

SERIAL
NUMBER
DATE OF PURCHASE
THE MODEL AND SERIAL NUMBERS WILL BE FOUND
ON A PLATE UNDER THE SEAT°
YOU SHOULD RECORD BOTH SERIAL NUMBER AND
DATE OF PURCHASE AND KEEP tN A SAFE PLACE
FOR FUTURE REFERENCE°

MAINTENANCE

AGREEMENT

A Sears Maintenance
Agreement
UCto Contact your nearest Sears

CUSTOMER

Read and observe the safety rules.

°

Fo!low a regular schedule in maintaining, caring for and
using your tractor.

°

Fotlow the instructions under "Customer Responsibilities" and "Storage" sections of this owner's manual

1,1
1.4
2_0
3.0
42
5..0
15

FRONT:
REAR:

CHARGING

3 AMPS BATTERY
5 AMPS HEADLIGHTS

SYSTEM:

14 PSI
10 PSI

30_35 FT, LBS.

..........

i

LiMiTED TWO YEAR WARRANTY

RC12YC

WARNING:
This tractor is equipped with an internal
combustion engine and should not be used on or near any
unimproved forest-covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped
with a spark arrester meeting applicable local or state laws
(if any). If a spark arrester is used, it should be maintained
in effective working order by the operator..
In the state of California the above is required by law
(Section 4442 of the California Public Resources Code)_
Other states may have similar laws. Federal laws apply on
federal lands. A spark arrester for the muffler is available
through your nearest Sears Authorized Service Center/
Department (See REPAIR PARTS section of this manual).

RESPONSIBILITIES

o

4.0 PINTS
3.5 PINTS

TIRE PRESSURE:

BLADE BOLT TORQUE:

is available on this prodstore for detaits_

REGULAR

ON CRAFTSMAN

H iH.-...:_...

illl¸

,

RIDING EQUIPMENT

For two (2) years from the date of purchase, if this Craftsman Riding Equipment is maintained, lubricated and tuned up according
to the instructions in the owner's manual, Sears will repair or replace, free of charge, any pads found to be defective in material
or workmanship,
This Warranty does not cover:
•
Expendable items which become worn during normal use, such as blades, spark plugs, air cleaners, belts, elc
•
Tire replacement or repair caused by punctures from outside objects, such as nails, thorns, stumps, or glass.
•
Repairs necessary because of operator abuse, negligence, improper storage or accident or the failure to maintain the
equipment according to the instructions contained in the owner's manual
•
Riding equipment used for commercial or rental purposes

LIMITED 90 DAY WARRANTY

ON BATTERY

For ninety (90) days from date of purchase, if any batter,] included with this riding equipment proves defective in material or
workmanship and our testing determines the battery will not hold a charge, Sears will replace the battery at no charge.
IN-HOME WARRANTY SERVICE ON YOUR CRAFTSMAN RIDING EQUIPMENT IS AVAILABLE AT NO-CHARGE FOR 30
DAYS FROM THE DATE OF PURCHASE.
PLEASE CONTACT YOUR NEAREST SERVICE CENTER.. AFTER 30 DAYS
FROM THE DATE OF PURCHASE, WARRANTY SERVICE IS AVAILABLE BY TAKING YOUR CRAFTSMAN RIDING EQUIPMENT TO YOUR NEAREST SEARS SERVICE CENTER_ (IN-HOME WARRANTY SERVICE WILL STILL BE AVAILABLE
AFTER 30 DAYS FROM THE DATE OF PURCHASE BUT A STANDARD TRIP CHARGE WILL APPLY.) THiS WARRANTY
APPLIES ONLY WHILE THIS PRODUCT IS IN THE UNITED STATES ......
This Warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.

SEARS,

ROEBUCK
i1,

AND CO.,
D/817 WA,, i HOFFMAN
,.
,i.i,
'II'H

3

ESTATES,
'
I I'WlIII'II, IL,I 60179
' III

''llw,l:lll,

TABLE OF CONTENTS
SAFETY RULES ............................................................
2
PRODUCT SPECIFICATIONS ......................................
3
CUSTOMER RESPONSIBILITIES ..................... 3, 15-19
WARRANTY ..................................................................
3
TABLE OF CONTENTS .................................................
4
INDEX ............................................................................
4
TRACTOR ACCESSORIES ..........................................
5
ASSEMBLY ...............................................................
7-9

OPERATION ..........................................................
10-14
MAINTENANCE SCHEDULE .....................................
15
SERVICE AND ADJUSTMENTS ........................... 20-25
STORAG E ...................................................................
26
TROUBLESHOOTING ...........................................
27-28
REPAIR PARTS - TRACTOR ................................ 30-47
REPAIR PARTS - ENGINE ....................................
48-53
PARTS ORDERING/SERVICE .................. BACK PAGE

INDEX

A
E
0
Accessories ...............................................................
5
Electrical:
Oil:
Adjustments:
Cold Weather Conditions ....... 13,17
Interlocks and Relays .........................
24
Brake ..............................................................
22
Schematic ........................................29
Engine ...........................................................
17
Carburetor ....................................................
25
Wiring Diagram .....................................
30
Storage ............................................................
26
Mower:
Engine:
Operation .................................................
10-14
Front-To-Back ..............................
21
Air Filter ........................................................
18
Operating Mower ..............................................
13
Side-To-Side ......................................
2!
Air Screen ............................................
18
Options:
Throttle Control Cable ........................
24
Accessories .................................................
5
Cooling Fins, Engine ...........................
18
Air Filter, Engine ..............................................
18
Oil Change .............................................
17
Spark Arrestor, ............................. 3,40
Air Screen, Engine ..........................................
18
Oil Level ..........................................
13,17
P
Assembly .......................................................
7-9
Oit Type ................................................
17
Parking Brake .............................................
11-12
B
Preparation .............................................
13
Parts Bag ..............................................................
6
Battery:
Repair Parts ........................................
48-53
Parts, Replacement/Repair ..............30-47
Charging ......................................................
7
Stading ................................................
14
Product Specifications .................................
3
Cleaning .....................................................
17
Storage ................................................
26
R
Starting with Weak Batten,/ ............23
F
Storage ..................................................
26
Fitters:
Repair Pads ..........................................
30-47
Terminals ............................................17
Air.........................................................
18
S
Belts:
Fuel ...............................................................
19
Safety Rules ...............................................2
Motion Drive
Fuel:
Seat ..................................................................................
8
Removal/Replacement
...............
22
Type ...............................................................
t3
Service
and
Adjustments
.....................
20-25
Mower Blade Drive
Storage .....................................................
26
Brake ..........................................................
22
Removal/Replacement
...............
22
Fuse ..............................................................
24
Carburetor
...............................................
25
Blade:
G
Fuse .....................................
24
Sharpening ............................................
t6
Gauge Wheels ........................................8-9
Hood Removal/Installation ...............
24
Replacement .......................................
16
H
Motion Ddve Belt
Brake Adjustment ........................................
22
Hood Removalttnstallation ....................24
Removal/Replacement ...................
22
C
Mower Blade Drive Belt
L
Carburetor Adjustment .................................
25
Remova!/Replacement ..............22
Leveling Mower Deck ..................................
21
Controls, Tractor, .......................................11
Mower Adjustment:
Lubrication
Chad
.............................................
15
Customer Responsibilities ..................
15-19
Front-to-Back ................................
21
M
Engine:
Side-to-Side ....................................
21
Maintenance Schedule ...............................
15
Air Filter ..........................................18
Mower Installation ..............................
20
Mower:
Air Screen, Engine .........................
18
Mower Removal .......................................
20
Adjustment, Front4o-Back ..............
21
Battery ..............................................
17
Tire Care ........................................
8,16,23
Adjustment, Side-to-Side ...............2t
Cooling Fins, Engine ....................
18
Slope Guide Sheet ....................................
55
Blade Sharpening ..................................
16
Engine Oil..............................................
17
Spark Plugs ..........................................................
19
Fuel Filter,
..........................................
19
Blade Replacement ............................
16
Specifications ......................................................
3
Cutting Height .....................................
12
Spark Plugs ......................................
19
Starling the Engine ...............................
13-14
Installation
..............................................
20
Tractor:
Steering Wheel .....................................7,23
Operation ................................................
13
Blades .................................................
16
Stopping the Tractor ...................................
t2
Removal .................................................
20
Lubrication Chad ..............................
15
Storage
..............................................................
26
Mowing Tips ....................................................
14
Maintenance Schedule ................
15
T
Muffler ..........................................................
i9
Tire Care ...................................
8,16,23
Throttle Control Cable Adjustment .......24
Spark Arrestor ..............................3,40
Cutting Height, Mower .................................
12
Tires .........................................................
8,16,23
Mulcher Plate .............................................
10
Trouble Shooting Chad .......................
27-28
Transaxle

Repair Pads .....................46-47

W
Warranty .............
:..................................................
3
Wiring Diagram ............................................
30
Wiring Schematic .......................................
29

4

ACCESSORIES

A

ATTACH

ENTS
........

i i ......

i i l i, ,l i,,

These accessories and attachments were available through most Sears retail outlets and service centers when the tractor was purchased_
Most Sears stores can order these items for you when you provide the model number of your tractor,

ENGINE
SPARK PLUG

MAINTENANCE
GAS CAN

ENGtNE OIL

FUEL STABILIZER

AIR FILTER

BLADES

BELTS

PERFORMANCE
Sears offers a wide variety of attachments that fit your tractor_ Many of these are listed below with brief explanations of how they can help
you. This list was current at the time of publication; however, it may change in future years _ more attachments may be added, changes
may be made in these attachments, or some may no longer be available or fit your modet. Contact your nearest Sears store for the
accessories and attachments that are available for your tractor.
Most of these attachments
attaching and detaching°

do not require additional hitches or conversion

kits (those that do are indicated) and are designed for easy

AERATOR promotes deep root growth for a healthy lawn. Tapered 25-inch steel spikes mounted on 10-inch diameter discs
puncture holes in soi_ at close intervals to let moisture soak in.
Steel weight tray for increased penetration
BAGGER lets you collect
grass clippings and leaves for a
healthier, neater looking lawn. Two Permanex containers hold
30-gallon plastic bags.
BUMPER protects front end of tractor from damage
CARTS make hauling easy
Variety of sizes available, plus
accessories such as side panel kits, tool caddy, cart cover,
protective mat and dolly.
CORING AERATOR takes small plugs out of soil to allow moisture and nutrients to reach grass roots, 36-inch swath
24
hardened steel coring tips 150 lb. capacity weight tray.
EASY OIL DRAIN VALVE makes oil changes easier, faster,
FRONT NOSE ROLLER canters in front of mower deck to reduce
chances of "scalping" on uneven terrain..
GANG HITCH lets you tow 2 or 3 pull-behind attachments at once,
such as sweepers, dethatchers, aerators (not for use with rollers,
carts or other heavy attachments),
GAUGE WHEELS on both sides of the mower deck reduce
chances of "scalping" on uneven terrain, For mower decks not so
equipped.
MULCH RAKE/DETHATCHER
loosens soil and flips thatch and
matted leaves to lawn surface for easy pickup. Twenty spring tine
teeth. Useful topreparebareareasforseeding.
Availableforfront
or rear mounting.
HIGH PERFORMANCE
REEL-ACTION
SPRING TINE DETHATCHER covers 36-inch wide path and
tosses thatch into large hopper. Mounts behind tractor.
MULCHING CLOSE-OUT PLATE KIT, once installed, lets you
mulch, discharge or bag clippings (bagger optional) without
changing blades.. For models not equipped as 3-in-1 Convertible
mowers° See "MOWER" in the Repair Parts section of this
manual,

SNOW BLADE for snow removal only. 14-inch high, 48-inch wide
blade clears42-inch path when angled felt or right. Raises, lowers
with side lever Adjustable skids; replaceable, reversible scraper
bar.. (Use with tire chains and wheel weights and/or rear drawbar
weight.)
SNOWTHROWER has 40-inch swath. Drum-type auger handles
powdery and wet/heavy snow., Mounts easily with simple pin
arrangement° Discharge chute adjusts from tractor seat.. 6-inch
diameter spout discharges snow 10 to 50 feet Lift controlled at
tractor seat. (Use with chains and wheel weights and!or rear
drawbar weight..)
SPRAYERS use 12-voft DC electric motor that connects to the
tractor battery or other 12-volt source.
Includes booms for
automatic spraying and hand held wand for spot spraying.. Wand
has adjustable spray pattern
For applying herbicides, insecticides, fungicides and liquid fertilizers,
SPREADER/SEEDERS
make seeding, fertilizing, and weed killing easy. Broadcast spreaders are also useful for granular deicers and sand.

RAMP TOPS AND FEET let you load and unload tractor from a
pickup truck_ Use with 2 x 8 or 2 x 10 lumber..
ROLLER for smoother lawn surface.
36-inch wide, 18*inch
diameterwater-tight
drum holds upto 390 lbs. of weight. Rounded
edges prevent harm to turf,. Adjustable scraper automatically
cleans drum

VACS for powerful collection of heavy grass clippings and leaves.
Optional wand attachment
to pick up debris in hard-to-reach
places. VAC/CHIPPER includes a chipper-shredder.
WEIGHT BRACKET for drawbar for snow removal applications
Uses (1) 55 lb. weight.
WHEEL WEIGHTS for rear wheels provide needed traction for
snow removal or dozing heavy materials

SWEEPERS let you collect grass clippings and leaves,
TILLER has 5 hp engine and 36-inch swath to prepare seed beds,
cultivate and compost garden residue. Tiller has its own built-in
tift and depth control system and does NOT require a sleeve hitch.
Fits any lawn, yard or garden tractor Simply hook up to the tractor
drawbar and go!
Optional
accessories
convert unit for
dethatching, aerating, hilling.., _without tools.
TIRE CHAINS are heavy duty; closely spaced extra-large cross
links give smooth ride, outstanding traction
TRACTOR CAB has heavy duty vinyl fabric over tubular steel
frame, ABS plastic top; clear plastic windshield offers 360 degree
visibility. Hinged metal doors with catch. Keeps operator warm
and dry, Remove vinyl sides and windshierds for use as sun
protector in summer. Optional accessories
include: tinted/
tempered solid safety glass windshield with hand operated wiper;
12-volt amber caution light for mounting on cab top

5

CONTENTS OF HARDWARE PACK
,,inn,H

Parts Bag contents

..........

i

shown full size

Parts packed separately

in carton

Metal
(2)
Sheet
Screws

O

#10-16 x 1/42
Steering
Wheel

(1) Large Flat Washer

Steering
Boot

(-

lI

Video
Cassette
(!) Shoulder Bolt 5t16-18

(1) Hex Bolt 1/2-13 x 1
Manual

Parts Bag

.......

IIIIIIIII_IIIIIIUIII_U

Parts bag contents
n

(1) Lock Washer

(2) Lock Washers

#10 x 5/8

, ii

11 jLjjj

not shown full size

...................................

(2) Washers 3/8
x 7/8 x 14 Gauge

1/2

(!) Washer" 17/32 x 1-3116 x 12 Gauge

(2) Screws

i, ii

t

(2) Shoulder
Bolts

Gauge _

(2) Centerlock Nuts

#10
Steering Wheel
Adapter

O

(2) Weld Nuts #10

i

ashers 3/16 x 3/4 x 16 Gauge

Bushing
Steedng

(_

_"

_ok
Assemblys
(2) Keys

(2) Hex Bolts 114-20 x 314
(2) Hex Nuts 1/4-20
Steering
Wheel
Insert
U

[2) Washers

9/32 x 5/8 x 16 Gauge
(2) Lock Washers

Slope Sheet

!/4

i,, ill ,

6

.......................

LJ

LY
i iill

Ill.

I

/

I / /

I Illllll

III,

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.
To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use
the correct tools as necessary to insure proper tightness°

TOOLS REQUIRED

FOR ASSEMBLY

STEERING

A socket wrench set will make assembly easier.. Standard
wrench sizes are listed_
(1) 5/16" wrench

(1) 3/4" Socket w/drive rachet

(2) 7/16" wrenches

Phillips Screwdriver

(1) 1/2" wrench

Tire pressure gauge

(1) 9/16" wrench

Utility knife

_

WHEEL INSERT
3t8-24 LOCKNUT

....
_

LARGE
WASHER FLAT
STEERING
WHEEL

)_

When right or left hand is mentioned in this manual, it
means when you are in the operating position (seated
behind the steering wheel).

STEERING

STEERING
BUSHING

I

TO REMOVE TRACTOR FROM CARTON

TABS
STEERING

Remove all accessible loose parts and parts cartons
from carton (See page 6).

.

Cut, from top to bottom, along lines on all four corners
of carton, and lay panels flat..

°

Check for any additional loose parts or cartons and
remove,

_

,oo

UNPACKCARTON
•

SCREW

STEERING
SHAFT

A

_

//
_

TAB
HOLE

POSITION)

BEFORE ROLLING TRACTOR OFF SKaD
ATTACH

STEERING

WHEEL

STEERING
SHAFT
(SHIPPING
POSITION)

(See Fig, 1)

o

Slide the steering bushing over the steering shaft°

°

Raise steering shaft forward until screw holes in dash
line up with steering bushing, Install two (2) sheet
metal screws and tighten securely°

•

Position steering boot over steering shaft

.

Place tabs of steering boot over tab slots in dash and
push down to secure.

°

Slide steering wheel adapter onto upper stee ring shaft.

-

Position front wheels of the tractor so they are pointing
straight forward°

o

Position steering wheel so cross bars are horizontal
(left to right) and slide onto adapter_

=

Assemble large flat washer and 3/8-24 iocknut and
tighten securely.

°

Snap steering wheel
wheel.

FIG. 1

CONNECT

CAUTION:
_

insert into center of steering

Release parking
pedal

brake by depressing

o
°

Place gearshift lever in neutral (N) position.
Roll tractor backwards off skid,,

•

Remove banding holding discharge guard up against
tractor,

Do not short battery termio

move metal bracelets,
wristwatch
nals.
connecting battery, rebands, Before
rings, etco

Remove cardboard packing from seat pan and lift seat
pan to raised position,.

°

Open battery box door.

o

Remove terminal protective caps and discard.

o

If this battery is put into service after month and year
indicated on label (label located between terminals)
charge battery for minimum of one hour at 6-10 amps.

°

First connect RED battery cable to positive (+) terminal
with hex bolt, flat washer, lock washer and hex nut as
shown° Tighten securely..

°

Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt, fiat washer, lock washer
and hex nut° Tighten securely.

°

Close battery box door

clutch/brake

7

be connected
from acciden-

•

OFF SKID (See Fig. 8)

Raise attachment lift lever to its highest position°
°

(See Figs. 2 and 3)

Positive terminal must
first to prevent sparking
tal grounding.

=
Remove protective plastic from tractor hood and grill..
IMPORTANT:CHECK FOR AND REMOVE ANY STAPLES
IN SKiD THAT MAY PUNCTURE TIRES WHERE TRACTOR
tS TO ROLL OFF SKiD

TO ROLL TRACTOR

BATTERY

ASSEMBLY
Openbatteryboxdoorfor:

SEAT

Inspection for secure connections
ware),,

o

o

Inspection for corrosion_

o

Testing battery,

e

Jumping (if required)_

,\

(to tighten hardSEAT PAN

Periodic charging ,.
DISCARD
TERMINAL
PROTECTIVE
CAPS
POSITIVE
(RED) CABLE

LOCK
WASHER
_,

HEX
NUT

LOCK WASHER

FLAT
WASHER

ADJUSTMENT
BOLT

LARGE FLAT WASHER

FIG. 4

VENT
HOLE
(KEEP
CLEAN)

CHECK TIRE PRESSURE
BOLT

The tires on your tractor were overinflated at the factory for
shipping purposes, Correct tire pressure is important for
best cutting performance,.
o

NEGATIVE
(BLACK) CABLE

FIG. 2

Reduce tire pressure to PS! shown in "PRODUCT
SPECIFICATIONS" on page 3 of this manual

CHECK

DECK LEVELNESS

Forbest cutting results, mower housing should be propedy
leveled. See "TO LEVEL MOWER HOUSING" in the
Service and Adjustments section of this manual,

SEA"['
PAN

CHECK

FOR

PROPER

POSITION

OF ALL

BELTS
See the figures that are shown for replacing motion and
mower blade drive belts in the Service and Adjustments
section of this manual_ Verify that the belts are routed
correctty._

BATTERY
BOXDOOR

CHECK

After you learn how to operate your tractor, check to see
that the brake is properly adjusted1. See "TO ADJUST
BRAKE" in the Service and Adjustments section of this
rnanuat.

FIG, 3

INSTALL

ASSEMBLE
GAUGE
DECK (See Fig. 5)

SEAT (See Fig. 4)

Adjust seat before tightening adjustment bolt.,
•
Remove cardboard packing on seat pan..
o Place seat on seat pan and assemble shoulder bolt,
•
Assemble adjustment bolt, lock washer and flat washer
loosely, Do not tighten°
•
Tighten shoulder bolt securely,
°
Lower seat into operating position and sit on seat°
o Slide seat until a comfortable position is reached which
allows you to press clutch/brake pedal all the way
down°
°
o

BRAKE SYSTEM

WHEELS

TO

MOWER

Assemble gauge wheels with tractor on a fiat level surface,

Get off seat without moving its adjusted position..
Raise seat and tighten adjustment bolt securely.

8

o

Adjust mower to desired cutting height (See "TO ADJUST MOWER CUTTING HEIGHT" in the Operation
section of this manual),,

°

With mower in desired height of cut position, gauge
wheels should be assembled so they are slightly off the
ground, Install gauge wheel in appropriate hole with
shoulder bolt, 3/8 washer and 3/8-I6 Iocknut and
tighten securefy,

°

Repeat for opposite side installing gauge wheel in
same adjustment hole.

ASSE

LY

GAUGE WHEEL
MOUNTING
BRACKET

DEFLECTOR
SHIELD

318-16 .-_'_
LOCKNUT
318" WASHER
_,,/.SHOULDER

BOLT

GAUGE WHEEL
LATCH
HOOKS

FIG, 5

INSTALL MULCHER PLATE
(See Figs, 6 and 7 )
o

FIG. 7

install two latch hooks to mulcher plate using screw,
washer, lock washer, and weld nut as shown..

TO CONVERT
DISCHARGING

NOTE: Pre-assemble weld nut to latch hook by inserting
weld nut from the top with hook pointing down_
•

Tighten hardware securely..

.

Raise and hold deflector shield in upright position.

°
.

Place front of mulcher plate over front of mower deck
opening and slide into place, as shown_
Hook front latch into hole on front of mower deck.

°

Hook rear latch into hole on back of mower deck°

,/CHECKLIST
BEFORE YOU OPERATE AND ENJOY YOUR NEW
TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE
THE BEST PERFORMANCE AND SATISFACTION FROM
THIS QUALITY PRODUCT
PLEASE REVIEW THE FOLLOWING CHECKLIST:

WASHER

NUT ,.\\\\
t.ATCH

,/

Al! assembly instructions have been completed..

v"

No remaining loose parts in carton°

v"

Batteryis property prepared and charged
1 hour at 6 amps).

v"

Seat is adjusted comfortably and tightened securely.

,/

All tires are properly inflated. (For shipping purposes,
the tires were overinflated at the factory).

v"

Be sure mower deck is properly leveled side-to-sidel
front-to-rear for best cutting results. (Tires must be
properly inflated for leveling)

,/

Check mower and drive belts. Be sure they are routed
properly around pulleys and inside all belt keepers,

,/

Check wiring. See that all connections are still secure
and wires are properly clamped_

HOOK POINTS DOWN

LOCK
WELD

SCREW
_

LATCH
HOOK

LOCK
WASHER

WASHER

OR

Simply remove mulcher plate and store in a safe place.
Your mower is now ready for discharging or installation of
optional grass catcher accessory.

CAUTION: Do not remove discharge
guard from mower. Raise and hold
guard when attaching mulcher plate
and allow it to rest on plate while in
operation.
WELD NUT FROM THE TOP

TO BAGGING

(Minimum

WHILELEARNING HOWTO USE YOUR TRACTOR, PAY
EXTRA A 7TENTION TO THE FOLLOWING IMPORTANT
ITEMS:

WELD
NUT

WASHER
_SCREW
MULCHER
PLATE

FIG. 6

9

¢'

Engine oil is at proper level..

¢"

Fuel tank is filled with fresh, clean, regular unleaded
gasoline.

¢"

Become familiar with all controls - their location and
function. Operate them before you start the engine.

,/

Be sure brake system is in safe operating condition.

.........

: :::::1111
i i ii i ii

OPERATmON
These symbols may appear on your tractor or in literature supplied with the product, Learn and understand their meaning.

BATTERY

CAUTION OR
WARNING

REVERSE

FORWARD

FAST

SLOW

d)ENGfNE ON

ENGINE OFF

OIL PRESSURE

CLUTCH

LIGHTS ON

LIGHTS OFF

MOWER HEIGHT

DIFFERENTIAL
LOCK

PARKING BRAKE
LOCKED

UNLOCKED

X
FUEL

CHOKE

REVERSE

NEUTRAL

HIGH

LOW

PARKING BRAKE

÷
MOWER LIFT

ATTACHMENT
CLUTCH ENGAGED

ATTACHMENT
CLUTCH DISENGAGED

HYDROSTATIC
DANGER, KEEP HANDS AND FEET AWAY

IGNITION

FREE WHEEL

(Hydro Models only)

10

OPERATION
,..ill

,i ii

,ll

ii i i

KNOW YOUR TRACTOR
READ THIS OWNER'S

MANUAL

Comparethe illustrations withyourtractor
this manual for future reference°

AND SAFETY

RULES

BEFORE

OPERATING

YOUR TRACTOR

to familiarize yourself with the locations of various controls and adjustments, Save

AMMETER
IGNITION
SWITCH

LIFT LEVER PLUNGER

/
ATTACHMENT

THROTTLE/CHOKE
CONTROL
ATTACHMENT
LEVER

I\1
CLUTCHIBRAKE
PEDAL

PARKING BRAKE
HEIGHT
ADJUSTMENT
KNOB
GEARSHIFT
LEVER

FIG. 8
Our tractors conform to the safety standards of the American National Standards Institute_
I
GEARSHIFT L.EVER: Selects the speed and direction o_
tractor,
i
ATTACHMENT LIFT LEVER: Used to raise and lower the
mower deck or other attachments mounted to your tractor,
LIFT LEVER PLUNGER: Used to release attachment lift
lever when changing its position,,

ATTACHMENT CLUTCFt LEVER: Used to engage the
mower blades, or other attachments mounted to your
tractor_
LIGHT SWITCH:

Turns the headlights on and off.

THROTTLE/CHOKE
CONTROL:
controlling engine speed°

Used for starting and

CLUTCHtBRAKE PEDAL: Used for declutching and braking the tractor and starting the engine°

IGNITION SWITCH:
engine.

PARKING BRAKE:
brake position°

HEIGHTADJUSTMENT
cutting height.

Locks clutch/brake

pedal into the

AMMETER:

11

Used for starting and stopping the
KNOB; Used to adjust the mower

Indicates battery charging (+) or discharging

OPERAT OIN
The operation of any tractor can result in foreign objects thrown into the eyes, which can
result in severe eye damage. Always wear safety glasses or eye shields while operating your
tractor or performing any adjustments or repairs. We recommend a wide vision safety mask
over the spectacles or standard safety glasses.
NOTE: Under certain conditions when tractor is standing
idle with the engine running, hot engine exhaust gases may
cause "browning" of grass. To eliminate this possibility,
always stop engine when stopping tractor on grass area&

HOW TO USE YOUR TRACTOR
TO SET PARKING

BRAKE

(See Fig. 9)

Your tractoris equipped with an operator presence sensing
switch. When engine is running, any attempt by the
operator to leave the seat without first setting the parking
brake will shut off the engine.
°

Depress clutch/brake
and hotd_

CAUTION:
Always stop tractor completely, as described above, before leaving the operator's position; to empty
grass catcher, etc.

pedal into full "BRAKE" position

Place parking brake lever in "ENGAGED" position and
release pressure from clutch/brake pedal.. Pedal should
remain in "BRAKE" position.. Make sure parking brake
will hold tractor secure.
ATTACHMENT CLUTCH
"ENGAGED"
POSITION

THROTTLE/
CHOKE
CONTROL

TO USE T!tROTTLE
o

Operating engine at less than full throttle reduces the
battery charging rate..

=

Full throttle offers the best bagging and mower performance.

LEVER

TO MOVE FORWARD
(See Fig, 9)

PARKING BRAKE
!'ENGAGED" POSITION

is controlled by the

o

Start tractor wit'h clutch/brake pedal depressed
gearshift lever in neutral (N) position.,

and

.

Move gearshift and range shift levers to desired position.

o
Slowly release clutch/brake
pedal to start movemenL
IMPORTANT;
BRING TRACTOR TO A COMPLETE
STOP
BEFORE
SHIFTING
OR CHANGING
GEARS. FAILURE
TO DO SO WILL SHORTEN THE USEFUL LIFE OF YOUR
TRANSAXLE

"DISENGAGED"
POSITION
HEIGHT ADJUSTMENT

AND BACKWARD

The direction and speed of movement
gearshift lever.

GEARSHIFT
LEVER

CLUTCHIBRAKE PEDAL
"DRIVE" POSITION

(See Fig. 9)

Always operate engine at full throttle

"DISENGAGED"
POSITION

"BRAKE"
POSITION

CONTROL

KNOB

FIG. 9

STOPPING

TO ADJUST MOWER
(See Fig. 9)

(See Fig. 9)

MOWER BLADES °

Move attachment clutch lever to "DISENGAGED"
sitiono
Depress clutch/brake

= Move gearshift
ENGINE •

o

Turn knob clockwise (f'-_)

°

Turn knob counterclockwise
height,

pedal into full "BRAKE" position.

position.

NOTE: Failure to move throttle control to slow (°_,)
position and allowing engine to idle before stopping may
cause engine to "backfire".
°

Turn ignition key to "OFF" position and remove key.
Always remove key when leaving tractor to prevent
unauthorized use.

=

Never use choke to stop engine.

to raise cutting height.
(_p-_) to lower'cutting

The cutting height range is approximately 1-1/2" to 4L The
heights are measured from the ground to the blade tip with
the engine not running., These heights are approximate
and may vary depending upon soil conditions, height of
grass and types of grass being mowed

lever to neutral (N) position.

Move throttle control to slow (_,)

HEIGHT

The cutting height is controlled by turning the height adjustment knob in desired direction..

po-

GROUND DRIVE o

CUTTING

12

•

The average lawn should be cut to approximately 2-1/2
inches during the cool season and to over 3 inches
during hot months. For healthier and better looking
lawns, mew often and after moderate growth,

=

For best cutting performance, .grass over6 inches in
height should be mewed twice., Make the first cut
relatively high; the second to desired heighL

OPEF AT ON
TO OPERATE

MOWER

(See Fig. 10)

Move gearshift lever to 1st gear. Be sure you have
allowed room for tractor to roll slightly as you restart
movemenL

Your tractor is equipped with an operator presence sensing switch.. Any attempt by the operator to leave the seat
with the engine ru nnJng and the attachment clutch engaged
will shut off the engine°

To restart movement, slowly release parking brake and
clutch/brake pedal.

•

Make all turns slowly,.

o

o

Select desired height of cut
Lower mower with attachment

lift control

Start mower blades by engaging attachment
control

TO TRANSPORT

clutch

TO STOP MOWER BLADES - disengage attachment
clutch control°
, illll ,IL,i,l,ll, ,ll,,iJll,,i ii i, i

"ENGAGED"
POSITION

Raise attachment lift to highest position with attachment lift control..

=

When pushing or towing your tractor, be sure gearshift
lever is in neutral (N) position,.

-

Do not push or tow tractor at more than five (5) MPH,,

, i1,1, i

without either the entire grass catcher,
CAUTION:
operate or
thethe
mower
on
mowers Do
so not
equipped,
discharge guard in place.
ATTACHMENT CLUTCH LEVER
"DISENGAGED"
POSITION

o

NOTE: To protect hood from damage when transporting
you r tractor on a truck or a trailer, be sure hood is closed and
secured to tractor, Use an appropriate means of tying hood
to tractor (rope, cord, etc,),

BEFORE

STARTING

THE ENGINE

ATTACHMENT

CHECK

HIGH POSITION

ENGINE

OIL LEVEL

(See Fig, 17)

•

The engine in your tractor has been shipped, from the
factory, already filled with summer weight oil.

°

Check engine oil with tractor on level ground

•

Unthread and remove oil fill cap/dipstick; wipe oil off.,
Reinsert the dipstick into the tube and rest oil fill cap on
the tube.. Do not thread the cap onto the tube, Remove
and read oi{ level. If necessary, add oil until "FULL"
mark on dipstick is reached. Do not overfill.,

•

For cold weather operation you should change oil for
easier starting (See "OIL VISCOSITY CHART" in the
Customer Responsibilities section of this manual)°

•

To change engine oil, see the Customer Responsibilities section in this manual

ADD GASOLINE
•
DISCHARGE
GUARD

IMPORTANT:
WHEN OPERATING
IN TEMPERATURES
BELOW 32°F(0_C), USE FRESH, CLEAN WINTER GRADE
GASOLINE
TO HELP INSURE GOOD COLD WEATHER
STARTING

FIG, 10

TO OPERATE

ON HILLS

WARNING:
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or methanol) can
attract moisture which leads to separation and formation of
acids during storage. Acidic gas can damage the fuel
system of an engine while in storage_ To avoid engine
problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the
engine and let it run until the fuel lines and carburetor are
empty, Use fresh fuel next season_ See Storage Instructions for additional information,,
Never use engine or
carburetor cleaner products in the fuel tank or permanent
damage may occur.,

hills
with slopes
greater
15down
° and
CAUTION:
Do not
drive than
up or
do not drive across any slope.
Choose the slowest speed before starting up or down
hills,
•

Avoid stopping or changing speed on hills.

o

If slowing is necessary,
slower position.

°

If stopping is absolutely necessary, push clutch/brake
pedal quickly to brake position and engage parking
brake°

Fill fuel tank,
Use fresh, clean, regular
unleaded
gasoline. (Use of leaded gasoline will increase carbon
and lead oxide deposits and reduce valve life)_

move throttle control lever to

13

CAUTION:
Fill to bottom of gas tank
filler neck, Do not overfill, Wipe off any
spilled oil or fuel Do not store, spill or
use gasoline near an open flame,
,,11 ill

11 =

A
TO START

ENGINE

(See Fig. 9)

ON
°

When starting engine for' the first time or if engine has run
out of fuel, it will take extra cranking time to move fuel from
the tank to the engine..
•

Depress clutch/brake

o

Place gearshift lever in neutral (N) position..

•

Move attachment clutch to "DISENGAGED"

o

Move throttle control lever to choke ( t",l ) position for
cold engine start_ For warm engine start, move throttle
control to fast (,_) position_

o

pedal and set parking brake._
position.

Insert key into ignitionand turn keyctockwise to"START"
position and release key as soon as engine starts. Do
not run starter continuously for more than fifteen
seconds per minute.. If engine does not start after
several attempts, move throttle control to fast (,_)
position, wait a few minutes and try again..

°

When engine starts, move throttle control to desired
position,

°

Allow engine to warm up for a few minutes before
engaging drive or attachments,,

FIG. 11

MULCHING

MOWING

TiPS

Mower-should be properly leveled for best mowing
performance. See '%0 LEVEL MOWER HOUSING" in
the Service and Adjustments section of this manual..
The left hand side of mower should be used for trimming.

•

Drive so that clippings are discharged onto the area
that has been cut. Have the cut area to the right of the
machine° This will result in a more even distribution of
clippings and more uniform cutting.

°

When mowing large areas, start by turning to the right
so that clippings will discharge away from shrubs,
fences, driveways, etc_ After one or two rounds, mow
in the opposite direction making left hand turns until
finished (See Fig° 11 )o

•

tf grass is extremely tall, it should be mowed twice to
reduce load and possible fire hazard from dried clippings. Make first cut relatively high; the second to the
desired height.

•

Do not mow grass when it is wet. Wet grass will plug
mower and leave undesirable clumps° Allow grass to
dry before mowing.

•

Always operate engine at full throttle when mowing to
assure better mowing performance and proper discharge of materiat_ Regulate ground speed by selecting a tow enough gear to give the mower cutting
performance as weil as the quality of cut desired.

TIPS

The special mulching blade will recur the grass clippings many times and reduce them in size so that as
they fall onto the lawn they wil! disperse into the grass
and not be noticed.. Also, the mulched grass will
biodegrade quickly to provide nutrients for the lawn.
Always mulch with your highest engine (blade) speed
as this will provide the best recutting action of the
blades..

Tire chains cannot be used when the mower housing
is attached to tractor'.

°

MOWING

IMPORTANT:
FOR BEST
PERFORMANCE,
KEEP
MOWER HOUSING
FREE OF BUILT-UP
GRASS AND
TRASH
CLEAN AFTER EACH USE..

NOTE: if at a high altitude (above 3000 feet) or in cold
temperatures (below 32°F), the carburetor fuel mixture
may need to be adjusted for best engine performance. See
"TO ADJUST CARBURETOR" in the Service and Adjustments section of this manual..

°

When operating attachments, select a ground speed
that will suit the terrain and give best performance of
the attachment being used.

=

Avoid cutting your lawn when it is wet. Wet grass tends
to form clumps and interferes with the mulching action
The best time to mow your lawn is the early afternoon..
At this time the grass has dried and the newly cut area
will not be exposed to the direct sun.

°

For best results, adjust the mower cutting height so that
the mower cuts off only the top one-third of the grass
blades (See Fig. 12). For extremely heavy mulching,
reduce your width of cut and mow slowly..

°

Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a second cut,
mow across or perpendicular to the first cut path.

°

Change your cutting pattern from week to week. Mow
north to south one week then change to east to west the
next week° This will help prevent matting and graining
of the lawn.

MAX 1t3

FIG, 12

14

CUSTO

RESPON

ILITIES
u, NNl"::"

INNNIN I

=,,,.
,,c=sc.=0u.=

FILL IN DATES

REGULARSERVICE.....,

T

/__ft'_E

RVI CE DATE S i

Check BrakeOperation

6/

6/

CheckTire Pressure

6/4
4

6##'

Check for LooseFasteners

6/

R sharpeniReplace Mower Blades
LubricationChart
C
......

6/#4
7
.....................
..............

6f4
_

CheckBatteryLeve!iRiecharge .....
i'ii".
..............

0

Clean Batteryand Terminals

_
$#*'

a

CheckTransaxteCooling

6#4

_5.

6/

_ChangeEngine Oil

6/

..................
_t,2,3

E ,,,.CleanAir F!!ter..........
N CleanAir Screen
iG Inspect MuffledSparkArrester

6/'2
6/2
6/
'

1

r

..............

,

:

'

..................

_.2

_#'2

E

.....

Replace

Spark Plug

........................

............

6/

Change mere ollen when operating under a heavy load or in htgh ambient lempe_atu[es
Service mere olten when opefaltng in dirty or dusly cendtlions
I! equipped with elf Iitler, change oil every 50 hours
Replace blades more ellen when mowing In sandy soi!

RECOMMEN

=6/ I

644

$/'2

Replace FuelFilter

GENERAL

"
.............

ReplaceAir Filler Paper Cartridge

1*
234-

'

6/ ......

.,

equipped)'

"
6/

......

Check EngineOil Level

(1,

'

_'s

Ad!us!Motion DriveB_e[!(s
) Tension

Filter

*

.....

Adjust Blade Belt(s) Tension

CleanEngine cooling Fins

I

...........
(If

T

Repiacielllio"

6/

I - I! equipped wilh adiustable system
0 - Not required if equipped wilh mainlenance4ree baiter.i
7 - Tighlen Iron[ axle pivot bolt to 35 f{ -Ibs maximum
Do net ovedighlen

LUBRICATION

DATIONS

The warranty on this tractor does not cover items that have
been subjected to operator abuse or negligence., To
receive full value from the warranty, operator must maintain
tractor as instructed in this manual,

(_SPINDLE
@FRONT

Some adjustments will need to be made periodically to
properly maintain your tractor°

ZERK_

CHART

. [_-

SPINDLE

ZERK (_)

WHEEL=====================================
FRONT WHEEL

BEARING

ZERK

_

'1|

f_

BEARING

1

All adjustments in the Service and Adjustments section of
this manual should be checked at least once each season.
•

®

Once a year you should replace the spark plug, clean
or replace air filter, and check blades and belts for
wear,, A new spark plug and clean air filter assure
proper air-fuel mixture and help your engine run better
and last longer°

BEFORE

CLUTCH
PIVOT(S)

EACH USE

°

Check engine oil level,,

•

Check brake operation°

°
•

Check tire pressure,,
Check for loose fasteners,,

(_)

ZERK

GEARSHIFT
PIVOTS

(_)

(_) SAE 30 OR 10W30 MOTOR OIL
(_) GENERAL

PURPOSE GREASE

(_) REFER TO CUSTOMER

15

RESPONSIBILITIES

"ENGINE"

SECTION

IMPORTANT:
DO NOT OIL OR GREASE THE PIVOT POINTS
WHICH HAVE SPECIAL NYLON BEARINGS
VISCOUS
LUBRI.
CANTS WILL ATTRACT
DUST AND DiRT THAT WILL SHORTEN
THE LIFE OF THE SELF-LUBRICATING
BEARINGS.
IF YOU
FEEL THEY MUST BE LUBRICATED,
USE ONLY A DRY, POWDERED GRAPHITE
TYPE LUBRICANT
SPARINGLY

CUSTO
i

,, i,/,i

i

i iJ

, llll ill ill i,,

,,

E
i

JLITtES

ESPONS

, i J ul ,,ulllu,,i,,H,,

TRACTOR

TO SHARPEN

Always observe safety rules when performing any maintenance.

Care should be taken to keep the blade balanced° An
unbalanced blade will cause excessive vibration and eventual damage to mower and engine.,

BRAKE OPERATION

o

The blade can be sharpened with a file or on a grinding
wheel. Do not attempt to sharpen while on the mower.

°

To check blade balance, you will need a 5/8" diameter
steel bolt, pin, or a cone balancer_ (When using a cone
balancer, follow the instructions supplied with balancer).

°

Slide blade on to an unthreaded portion of the steel bolt
or pin and hold the bolt or pin parallel with the ground.
If blade is balanced, it should remain in a horizontal
position. If either end of the blade moves downward,
sharpen the heavy end until the blade is balanced.,

If tractor requires more than six (6) feet stopping distance
at high speed in highest gear, then brake must be adjusted..
(See 'q'o ADJUST BRAKE" in the Service and Adjustments section of this rnanua0.

TIRES
o

Maintain proper air pressure in all tires (See "PRODUCT SPECIFICATIONS" on page 3 of this manual)

•

Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber'.,

o

Avoid stumps, stones, deep ruts, sharp objects and
other hazards that may cause tire damage.

BLADE

(See Fig. 14)

NOTE: Do not use a nail for balancing blade. The lobes of
the center hole may appear to be centered, but are not°
CENTER HOLE

BLADE CARE
For best results mower' blades must be kept sharp
place bent or damaged blades,.

BLADE REMOVAL

Re-

(See Fig. 13)

•

Raise mower to highest position to allow access to
blades..

•

Remove hex bolt, lock washer and flat washer secu ring
blade.,

o

install new or resharpened blade with trailing edge up
towards deck as shown.

o

Reassemble hex bolt, lock washer and flat washer in
exact order as shown.

FIG. 14

BATTERY

° Tighten bolt securely (30-35 FL Lbs_ torque),,
IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED

Your tractor' has a battery charging system which is sufficient for normal use., However, periodic charging of the
battery with an automotive charger will extend its life.

NOTE: We do not recommend sharpening blade - but ifyou
do, be sure the blade is balanced.

MANDREL
ASSEMBLY

BLADE

BLADE

5/8" BOLT
OR PIN

°

Keep battery and terminals clean.

•

Keep battery bolts tight.

o

Keep small vent holes open (See "CONNECT BATTERY" in the Assembly section of this manual),

°

Recharge at 6 amperes for 1 hour.

TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battery and terminals can cause
the battery to "leak" power,.
TRAILING EDGE

FLAT BOLT
WASHER
HEX
(GRADE

_,

,

Open battery box door,

°

Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor.

°

Wash battery with solution of four' tablespoons of
baking soda to one gallon of water,. Be careful not to get
the soda solution into the cells,.

°

Rinse the battery with plain water and dry.

o

Clean terminals and battery cable ends with wire brush
until brighL

•
°

Coat terminals with grease or petroleum jelly,.
Reinstall battery (See "CONNECT BATTERY"
Assembly section of this manual)_

!

*A GRADE 8 HEAT TREATED BOLT CAN BE
IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 13

16

in the

V-BELTS

TO CHANGE ENGINE OIL (See Fig_ 15)

Check V-belts for deterioration and wear after 100 hours of
operation and replace if necessary_ The belts are not
adjustable° Replace belts if they begin to slip from wear_,

Determine temperature range expected before oil change
All oil must meet API service classification SF or SG,
o
Be sure tractor is on level surface

TRANSAXLE

°

COOLING

Oil will drain more freely when warm,
Catch oi! in a suitable container,,

Keep transaxle free from build_up of dirt and chaff which
can restrict cooling.

°
°

ENGINE

°

Remove drain plugo

o

LUBRICATION

After oil has drained completely, replace oil drain plug
and tighten securely.

Only use high quality detergent oil rated with API service
classification SF or SG. Select the oil's SAE viscosity grade
according to your expected operating temperature°

Refill engine with oil through oil fill dipstick tube. Pour
slowly. Do not overfill. For approximate capacity see
"PRODUCT SPECIFICATIONS"
on page 3 of this
manual.

SAE VISCOSITY GRADES

Use gauge on oil fill cap/dipstick for checking level.
Insert dipstick into the tube and rest the oil fill cap on the
tube. Do not thread the cap onto the tube when taking
reading., Keep oil at "FULL" line on dipstick. Tighten
cap onto the tube securely when finished.

L

-20"

°C .30°
....

04

-20°

TE, MPERATURE

30"

-10°

32 =' 40"

0"

RANGE ANTICIPATED

60 _

,,,,!0_
BEFORE

60 °

Remove oil fill cap/dipstick, Be careful not to allow dirt
to enter the engine when changing oil,,

!00 °

....................
20=
30'

4 o

NEXT OIL CHANGE

AIR CLEANER
COVER

NOTE: Although multi-viscosity oils (5W30, 10VV30 etc.,)
improve starting in cold weather, these multi-viscosity oils
wilt result in increased oil consumption when used above
32°F. Check your engine oil level more frequently to avoid
possible engine damage from running low on oil,

KNOB
NUT

FOAM
PRE-CLEANER

Change the oil after the first two hours of operation and
every 50 hours thereafter or at least once a year if the
tractor is not used for 50 hours in one year.
Check the crankcase oil level before starting the engine
and after each eight (8) hours of operation_ Tighten oil fill
cap/dipstick securely each time you check the oil level
PAPER CARTRIDGE

CLEANER
BASE
:ILL
CAP/DIPSTICK

AIR
SCREEN

DRAIN
PLUG

FIG. 15

17

ILITIES

ESPO
AIR FILTER

CLEAN AIR INTAKE/COOLING

(See Fig. 15)

Your engine wilt not run properly using a dirty air filter,.
Clean the foam pre-cleaner after every 25 hours of operation or every season. Service paper' cartridge every 100
hours of operation or every season, whichever occurs first.

To insure proper cooling, make sure the grass screen,
cooling fins, and other external surfaces of the engine are
kept clean at all times.
Every 100 hours of operation (more often under extremely
dusty, dirty conditions), remove the blower housing and
other cooling shrouds. Clean the cooling fins and external
surfaces as necessary. Make sure the cooling shrouds are
reinstalled,.

Service air' cleaner more often under dusty conditions..
•

Remove knob and cover_

•
Remove wing nut and air cleaner from base.
TO SERVICE PRE-CLEANER
°

Slide foam pre-cleaner off cartridge.

•

Wash it in liquid detergent and water_

•

Squeeze it dry in a clean cloth.

NOTE: Operating the engine with a blocked grass screen,
dirty or plugged cooling fins, and/or cooling shrouds removed will cause engine damage due to overheating.

MUFFLER

°

Saturate it in engine oil. Wrap it in clean, absorbent
cloth and squeeze to remove excess oil
TO SERVICE CARTRIDGE
•

o
o

Inspect and replace corroded muffler and spark arrester (if
equipped) as it could create a fire hazard and/or damage.

SPARK

Gently tap the flat side of the paper cartridge to dislodge dirt. Do not wash the paper cartridge or use
pressurized air, as this will damage the cartridge.
Replace a dirty, bent, or damaged cartridge.

AIR SCREEN

PLUGS

Replace spark plugs at the beginning of each mowing
season or' after every 100 hours of operation, whichever
occurs first. Spark plug type and gap setting are shown in
"PRODUCT SPECIFICATIONS" on page 3 of this manual.

Reinstall the pre-cteaner (cleaned and oiled) over the
paper cartridge..
Reassemble air' cleaner, wing nut, cover and tighten
knob securely.

CLEAN

AREAS

(See Fig. 15)

Air screen must be kept free of dirt and chaff to prevent
engine damage from overheating. Clean with a wire brush
or compressed air to remove dirt and stubborn dried gum
fibers..

18

ENGINE

OIL FILTER

(See Fig. 16)

IN-LINE

FUEL FILTER

(See Fig. 17)

Replace the engine oil filter every season or every other oil
change if the tractor is used more than 100 hours in one
year°

The fuel filter should be replaced once each season. If fuel
filter becomes clogged, obstructing fuel flow to carburetor,
replacement is required°

o

Drain oil from engine crankcase (See "TO CHANGE
ENGINE OIL" in this section of this manual, through
step remove drain plug).

•

With engine cool, remove filter and plug fuel line
sections.

•

•

Remove oil filter and wipe off filter adapter°

Place new fuel filter in position in fuel line with arrow
pointing towards carburetor,.

°

Apply a thin coating of new engine oil to the rubber
gasket on replacement oil filter°

°

Be sure there are no fuel line leaks and clamps are
properly positioned.

°

Install replacement oil filter on filter adapter° Turn oil
filter clockwise until rubber gasket contacts the filter
adapter, then tighten filter an additional 1/2 turn_

=

Immediately wipe up any spilled gasoline°

°

Fill crankcase with new oil (See "TO CHANGE ENGINE OIL" in this section of this manual). For approximate capacity see "PRODUCT SPECIFICATIONS" on
page 3 of this manual°

•

CLAMP

CLAMP

i!,:

Start the engine and check for oil leaks, Correct any
teaks before placing engine into full operation.
FUEL
FILTER

FIG. 17

CLEANmNG
o

Clean engine, battery, seat, finish, etc_ of all foreign
matter°

°

Keep finished surfaces and wheels free of all gasoline,
oil, etc.

o

Protect painted surfaces with automotive type wax.

We do not recommend using a garden hose to clean your
tractor unless the electrical system, muffler, air filter and
carburetor are covered to keep water out, Water in engine
can result in a shortened engine life.
FIG. 16

19

SERVICE AND ADJUSTMENTS
CAUTION:
@
o
o
o
o

BEFORE PERFORMING

ANY SERVICE OR ADJUSTMENTS:

Depress clutch/brake pedal fully and set parking brake.
Place gearshift lever in neutral (N) position,
Place attachment clutch in "DISENGAGED"
position.
Turn ignition key "OFF" and remove key.
Make sure the blades and all moving parts have completely stopped.
Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with
plug,

TRACTOR
TO REMOVE

MOWER

LEVER

(See Fig. 18)

Mower wi!l be easier to remove from the right side of tractor.
o
o

Place attachment clutch in "DISENGAGED" position.
Move attachment lift lever forward to lower mower to its
lowest position

°

Roll belt off engine pulley

o

Disconnect clutch rod from clutch lever by removing
retainer spring

•

Disconnect anti-sway bar from chassis bracket by
removing retainer spring_

,

Disconnect suspension arms from rear deck brackets
by removing retainer springs,

°

Disconnect front links from deck by removing retainer
springs_

°

Raise lift lever to raise suspension arms Slide mower
out from under tractor,

]ETAINER
SPRING

RETAINER
SPRING

IMPORTANT:
IF AN ATTACHMENT OTHER THAN THE
MOWER IS TO BE MOUNTED TO THE TRACTOR, THE
R.H. AND L,H, SUSPENSION ARMS MUST BE REMOVED
FROM TRACTOR

TO INSTALL

MOWER

ANTI-SWAY

(See Fig. 18)

°

Raise attachment lift lever to its highest position,

°

Slide mower under tractorwith discharge guardto right
side of tractor

o
°

Lower iift lever to its lowest position,
install mower in reverse order of removal instructions.

BAR

RETAINER
SPRINGS
(BOTH SIDES)

FIG. 18

2O

SERVmCE AN
TO LEVEL

MOWER

ADJUSTMENTS

HOUSING

FRONT-TO-BACK ADJUSTMENT (See Figs. 21 and 22)
IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE,, IF
THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS
NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS
EQUALLY SO MOWER WILL STAY LEVEL SIDE-TOSIDE.,

Adjust the mower while tractor is parked on level ground or
driveway°
Make sure tires are properly inflated (See
"PRODUCT SPECIFICATIONS" on page 3 of this manual).
If tires are over or underinflated, you will not properly adjust
your mower°
SIDE-TO-SIDE

ADJUSTMENT

To obtain the best cutting results, the mower housing
should be adjusted so that the front is approximately 1/4" to
3/4" lower than the rear when the mower is in its highest
position.
Check adjustment on right side of tractor. Measure distance "D" directly in front and behind the mandrel at bottom
edge of mower housing as shown,
•
Before making any necessary adjustments, check that
both front links are equal in length, Both links should be
approximately 10-3/8",
•
If links are not equal in length, adjust one link to same
length as other link.
.
To lower front of mower loosen nut "E" on both front
links an equal number of turns.
•
When distance "D" is 1/4" to 3/4" lower at front than
rear, tighten nuts "F" against trunnion on both front
links.

(See Figs. 19 and 20)

°

Raise mower to its highest position.

°

At the midpoint of both sides of mower, measure height
from bottom edge of mower to ground,, Distance "A" on
both sides of mower should be the same or within 1/4"
of each other°

o

If adjustment is necessary, make adjustment on one
side of mower only,,

°

To raise one side of mower, tighten lift link adjustment
nut on that side,

°

To lower one side of mower, loosen lift link adjustment
nut on that side°

NOTE: Each full turn of adjustment nut will change mower
height about 1/8".
°

Recheck measurements

after adjusting

BOTTOM EDGE
OF MOWER TO
GROUND

•

BOTTOM EDGE
OF MOWER TO
GROUND

•
•

GROUND

LINE

To raise front of mower, loosen nut "F" from trunnion on
both front links,, Tighten nut "E" on both front links an
equal number of turn&,
When distance "D" is 1/4" to 3/4" lower at front than
rear, tighten nut"F" against trunnion on both front links,,
Recheck side4o-side adjustment°
:>, %

A

\\

FIG. 19

",,

_

_ ,,_

MANDREL

'-,r'

SUSPENSION
ARM

FIG. 21
BOTH FRONT LINKS MUST BE EQUAL

LIFT LINK
ADJUSTMENT

1N LENGTH

NUT

FIG. 20
NUI "E"
NUT "F"

FRONT LINKS

21

TRUNNION

FIG. 22

SERVHCE AND ADJUSTMENTS
TO REPLACE
(See Fig. 23)

MOWER

BLADE

DRIVE

WITH PARKING BRAKE "ENGAGED"

BELT

The mower'blade drive belt may be replaced without tools,.
Park the tractor on level su_ace,_ Engage parking brake._
BELT REMOVAL•

Remove mower from tractor (See "TO REMOVE
MOWER" in this section of this manual),

•

Work belt off both mandrel pulleys and idler pulleys.

=

Pull belt away from mower,,

BELT INSTALLATION •

Install new belt in reverse order of removal.

.

Make su re belt is in all pulley grooves and inside a!l belt
guides°
install mower in reverse order of removal instructions

.

FIG. 24
MANDREL
PULLEY

IDLER
PULLEYS

TO REPLACE
(See Fig. 25)

MOTION

DRIVE

BELT

Park the tractor on levei surface,, Engage parking brake,,
For' assistance, there is a belt installation guide decal on
bottom side of left footrest.

MANDREL
PULLEY

BRAKE

Remove mower (See "TO REMOVE MOWER" in this
section of this manuaL)

°

Remove upper belt keeper,.

=
o

Remove belt from stationary idler and clutching idler,
Pull heft slack toward rear of tractor, Remove belt
upwards from transaxle pulley by deflecting belt keepers,,

o

Pull belt toward front of tractor and remove downwards
from around engine pu]ley_

°
instatt new belt by reversing above procedure.
IMPORTANT: MAKE SURE UPPER BELT KEEPER IS
POSITIONED PROPERLY BETWEEN LOCATOR TABS.

FIG. 23

TO ADJUST

o

ENG
PULLEY

(See Fig. 24)

LOCATOR
TABS

CLUTCHING
IDLER

Your tractor is equipped with an adjustable brake system
which is mounted on the right side of the transaxle_
tf tractor requires more than six (6) feet stopping distance
at high speed in highest gear-, then brake must be adjusted.
°

Depress clutch/brake pedal and engage parking brake.

.

Measure distance between brake operating arm and
nut "A" on brake rod,,

UPPER BELT
KEEPER
IDLER

If distance is other than 1-1/2", loosen jam nut and turn
nut "A" until distance becomes 1-1/2",, Retighten jam
nut against nut "A",

TRANSAXLE
PULLEY

Road test tractor for proper stopping distance as stated
above. Readjust if necessary. If stopping distance is
still greater than six (6) feet in highest gear, further
maintenance is necessary. Contact your nearest authorized service center/department_

FIG. 25

22

ERVmCEAN
TO ADJUST

STEERING

ADJUSTMENTS

WHEEL ALIGNMENT

TO START ENGINE WITH A WEAK
See Fig. 27)

If steering wheel crossbars are not horizontal (left to right)
when wheels are positioned straightforward, remove steering wheel and reassemble per instructions in the Assembly
section of this manual

FRONT WHEEL

_u=_,,, _

CAUTION; Lead-acid batteries generate explosive gases. Keep sparks, flame
and smoking materials away from batteries.
Always wear eye protection
when around batteries.

TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on
your tractor, if damage has occurred to affect the front
wheel toe-in or camber, contact your nearest authorized
service center/department,,

TO REMOVE WHEEL
(See Fig. 26)

If your battery is too weak to start the engine, it should be
recharged°
If "jumper cables" are used for emergency
starting, follow this procedure:

FOR REPAIRS

•

Block up axle secure{y,

°

Remove axle cover, retaining ring and washers to allow
wheel removal (rear wheel contains a square key - Do
not Iose)_

BATTERY

IMPORTANT:
YOUR TRACTOR IS EQUIPPED WITH A 12
VOLT NEGATIVE
GROUNDED
SYSTEM
THE OTHER
VEHICLE
MUST ALSO
BE A 12 VOLT
NEGATIVE
GROUNDED
SYSTEM,
DO NOT USE YOUR TRACTOR
BATTERY TO START OTHER VEHICLES_

TO ATTACH JUMPER CABLES o

•

Repair tire and reassemble°

°

On rear wheels only: align grooves in rear wheel hub
and axle. Insert square key.

=

•

Replace washers and snap retaining ring securely in
axle groove.

°

•

Replace axle cover.

Connect each end of the RED cable to the POSITIVE
(+) terminal of each battery, taking care not to short
against chassis,
Connect one end of the BLACK cable to the NEGATIVE (-) terminal of fully charged battery_
Connect the other end of the BLACK cable to good
CHASSIS GROUND, away from fuel tank and battery

TO REMOVE CABLES, REVERSE ORDER =

WASHERS

°

RETAINING
RING

BLACK cable first from chassis and then from the fully
charged battery.
RED cabte last from both batteries,
POSITIVE TERMINAL

NEGATIVE

TERMINAL

1
AXLE COVER

_"SQUARE

KEY

(REAR WHEEL ONLY)

FIG. 26
CHASSIS
CABLES

CHARGED
BATTERY
POSITIVE
TERMINAL

NEGATIVE
TERMINAL

FIG. 27

23

SERVUCE AND ADJ
TO REPLACE

HEADLIGHT

BULB

,

Raise hood.

=

Pull bulb holder out of the hole in the backside of the
grill.

=

Replace bulb in holder and push bulb holder securely
back into the hole in the backside of the grill

,

CIosehood_

INTERLOCKS

STMENTS

HOOD

HEADLIGHT
WIRE
CONNECTOR

AND RELAYS

Loose or damaged wiring may cause your tractor' to run
poorly, stop running, or prevent it from starting.
=

Check wiring_ See electrical wiring diagram in the
Repair Parts section of this manual.

TO REPLACE

FUSE

Replace with 30 amp automotive-type pfug-in fuse. The
fuse holder' is located behind the dash.

TO REMOVE HOOD
(See Fig. 28)

FIG. 28

AND GRILL ASSEMBLY

•

Raise hood..

o

Unsnap headlight wire connector_

=

Stand in front of tractor. Grasp hood at sides, tilt toward
engine and lift off of tractor..

•

To replace, reverse above procedures.

24

•

_l
.....

ii,i

,i i , i,l,,i

,,

i ....

SERVmCE AND ADJUSTMENTS
ENGINE

ACCELERATION

TO ADJUST
THROTTLE
(See Fig. 29)

CONTROL

°

CABLE

The throttle control has been preset at the factory and
adjustment should not be necessary.. Check adjustment as
described below before loosening cable. If adjustment is
necessary, proceed as follows:
•

With engine not running, move throttle control Iever
from slow (,_) to choke (1\1) position.. Slowly move
lever from choke (1\1)to fast (,_) position.

o

Check to see if hole in throttle lever and hole in speed
control bracket are aligned°

•

If holes are not aligned, loosen cable clamp screw and
align the holes by inserting a pencil or a 1/4" drill bit
through both holes,.

•

Pull throttle cable up to remove slack and tighten cable
clamp screw_ Remove alignment pencil or drill bit..

TO ADJUST

CARBURETOR

TEST -

Move throttle control lever from slow (-€_) to fast
position, If engine hesitates or dies, turn idle
adjusting needle out (counterclockwise) 1/8 turn.
peat test and continue to adjust, if necessary,
engine accelerates smoothly_

High speed stop is factory adjusted°
Do not adjust damage may result.
IMPORTANT:
NEVER TAMPER WITH THE ENGINE
GOVERNOR, WHICH IS FACTORY SET FOR PROPER
ENGINE SPEED° OVERSPEEDING THE ENGINE ABOVE
THE FACTORY HIGH SPEED SETTING
CAN BE
DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED
HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR
NEAREST
AUTHORIZED
SERVICE
CENTER/
DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND
EXPERIENCE
TO
MAKE
ANY
NECESSARY
ADJUSTMENTS
CABLE
CLAMP
SCREW

(See Fig. 30)

The carburetor has been preset at the factory and adjustment should not be necessary_ However, minor adjustment may be required to compensate fordifferences in fuel,
temperature, altitude or toad. If the carburetor does need
adjustment, proceed as follows:

SPEED
BRACKET

In general, turning the adjusting needles in (clockwise)
decreases the supply of fuel to the engine giving a leaner
fuel/air mixture° Turning the adjusting needles out (counterclockwise) increases the supply of fuet to the engine giving
a richer fueVair mixture,.
IMPORTANT:
DAMAGE
SEATS IN CARBURETOR
TURNED tN TOO TIGHT

TO THE NEEDLES
AND THE
MAY RESULT IF NEEDLE IS

PRELIMINARY

-

SE'I-[ING

THROTFLE
LEVER

FIG. 29

•

Be sure you have a clean air filter and the throttle
control cable is adjusted properly (see above).

.

With engine off turn idte fuel adjusting needle in (clockwise) closing it finger tight and then turn out (counterclockwise) 1 turn.

IDLE SPEED
ADJUSTING
SCREW

FINAL SETTING °

Start engine and allow to warm for five minutes. Make
final adjustments with engine running and shift/motion
control lever in neutral (N) position.

°

Idle speed setting - With throttle control lever in slow
(,€_) position, engine should idle at 1750 RPM. If
engine idles too slow or fast, turn idle speed adjusting
screw in or out until correct idle is attained.

°

Idle fuel needle setting - With throttle control lever in
slow (.¢_) position, turn idle fuel adjusting needle in
(clockwise) until engine begins to die and then turn out
(counterclockwise) approximately 1/8 to 1/4 turn to
obtain best low speed performance..

o

('_s,)
fuel
Reuntil

IDLE FUEL
ADJUSTING
NEEDLE

FIG. 30

Recheck idle speed.. Readjust if necessary,

25

, i,,ll ,,ll

,ll,,,i

......................

iill

i

STORAGE
ENGINE

Immediately prepare your' tractor for storage at the end of
the season or if the tractor' will not be used for 30 days or
more,

FUEL SYSTEM
IMPORTANT:
IT IS IMPORTANT
TO PREVENT
GUM
DEPOSITS
FROM FORMING
IN ESSENTIAL
FUEL
SYSTEM PARTS SUCH AS CARBURETOR,
FUEL FILTER,
FUEL HOSE, OR TANK DURING
STORAGE.
ALSO,
EXPERIENCE
INDICATES
THAT ALCOHOL
BLENDED
FUELS (CALLED GASOHOL
OR USING ETHANOL
OR
METHANOL)
CAN ATTRACT MOISTURE WHICH LEADS
TO SEPARATION
AND FORMATION
OF ACIDS DURING
STORAGE.
ACIDIC
GAS CAN DAMAGE
THE FUEL
SYSTEM OF AN ENGINE WHILE IN STORAGE.

CAUTION: Never store the tractor with
gasoline in the tank inside a building
where fumes may reach an open flame
or spark,
Allow the engine to cool
before storing in any enclosure.

TRACTOR
Remove mower from tractor for winter storage.. When
mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc.. Store in a
clean, dry area.
o

Clean entire tractor (See"CLEANING" in the Customer
Responsibilities section of this manual)°

•

Inspect and replace belts, if necessary (See belt replacement instructions in the Service and Adjustments
section of this manual).,

o

Lubricate as shown in the Customer Responsibilities
section of this manual.,

.

Be sure that all nuts, bolts and screws are securely
fastened.. Inspect moving parts for damage, breakage
and wear., Replace if necessary._

=

Touch up atl rusted or chipped paint surfaces; sand
tightly before painting..

Fut]y charge the battery for storage_

o

After a period of time in storage, battery may require
recharging.

•

°

Start the engine and let it run until the fuel lines and
carburetor are empty.,

o

Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage
container., Always follow the mix ratio found on stabilizer
container. Run engine at least 10 minutes after' adding
stabilizer to allow the stabilizer to reach the carburetor. Do
not drain the gas tank and carburetor if using fuel stabilizer_

ENGINE OIL
Drain oil (with engine warm) and replace with clean engine
oil. (See "ENGINE" in the Customer Responsibilities
section of this manual).

BATTERY
•

Drain the fuel tank..

o

CYLINDERS

To help prevent corrosion and power leakage during
long periods of storage, battery cables should be
disconnected and battery cleaned thoroughly (see "TO
CLEAN BATTERY AND TERMINALS" in the Customer Responsibilities section of this manual)_

o

Remove spark plug(s)..

°

Pour one ounce of oil through spark plug hole(s) into
cylinder(s).
Turn ignition key to "START" position for a few seconds
to distribute oil..

•

Replace with new spark plug(s),

After' cleaning, leave cables disconnected and place
cables where they cannot come in contact with battery
terminal&

OTHER

°

Be sure battery drain tube is securely attache&

o

Do not store gasoline from one season to another.

•

If battery asrernoved from tractor for storage, do not
store battery directly on concrete or damp surfaces..

o

Replace your gasoline can if your can starts to rusL
Rust and/or dirt in your gasoline will cause problem&

°

If possible, store your' tractor indoors and cover it to
give protection from dust and dirt.,

•

Covetyour tractor with a suitable protective cover that
does not retain moisture. Do not use plastic. Plastic
cannot breathe which allows condensation to form and
will cause your tractor to rust.
IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE
AND EXHAUST AREAS ARE STILL WARM.

26

TROUBLESHOOTmNG POINTS
..................

ii i

PROBLEM

CAUSE

Will not start

t

Out of fuel.

2
3
4,
5,
&
7

Engine not "CHOKED"
Engine flooded.
Bad spark plug
Dirty air filter.
Dirty fuel filter.
Wafer in fuel

8.

Loose or damaged wiring

Hard to start

CORRECTION

properly

1

Fill fuel tank

2
3.
4,
5
6,
7

See "TO START ENGINE" in Operation section,
Wait several minutes before attempting to start
Replace spark p}ug,
Clean/replace air filter
Replace fuel filter
Drain fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter,.
Check at{ wiring,,
Contact an authorized serv{ce facility
Contact an authorized service facility,

9.
i 0,

Carburetor out of adjustment
Engine valves out of adjustment

8
9,
10,

1
2
3
4,
5.
6
7.
8

Dirty air filter
Bad spark plug,
Weak or dead battery
Dirty fuel filter
Stale ordirty fuel
Loose or damaged wiring
Carburetor out of adjustment
Engine valves out of adjustmenL

t
2
3
4
5,
6
7,
8

Clean/replace air fitter
Replace spark plug
Recharge or replace battery
Replace fuel filter
Drain fuel tank and refill with fresh gasoline
Check allwiring
Contact an authorized service facil{ty,
Contact an authorized service facility,
ii

Engine will not turn over

1
2.
3,
4

Clutch/brake pedal not depressed
Attachment clutch is engaged
Weak or dead battery
Blown fuse

5,
6,
7,.
8,
9

Engine clicks but wil! not
start

Loss of power

vibration

ii i

i i

Corroded battery terminals
Loose or damaged widng
Faulty ignition switch
Faulty solenoid or starter
Faulty operator presence switch(as),

1
2,
3
4
5
6,
7.
8.
9

Depress clutch/brake pedal
Disengage attachment clutch,
Recharge or replace battery
Replace fuse
Clean battery terminals
Check all wiring
Check/replace ignition switch
Check/replace sofenoid or starter
Contact an authorized service facility

1.
2
3,
4

Weak or dead battery,
Corroded battery terminals,
Loose or damaged wiring
Faulty solenoid or starter,

1
2,
3,
4

Recharge or replace battery,
Clean battery terminals
Check a_lwiring
Check!replace solenoidor starter,

1
2,
3
4,
5.
6
7
8
9

Cutting too much grass/too fast,
Throttle in"CHOKE" position.
Build-up of grass, leaves and trash under mower,
Dirty air fitter_
Low oil leveVdirty oif,
Fabtlty spark plug
Dirty fuel fi{ter
Stale or dirty fueI
Water in fuel

1
2,
3,
4
5
6
7
8,
9

Set in "Higher Cut" position/reduce speed,
Adjust throttle control
Clean underside of mower housing,
Clean/replace air filter
Check oil level/change oil
Clean and regap orchange spark plug
Replace fuel filter
Drain fuel tank and refill with fresh gasoline
Drain fuel tank and carburetor, refill tank with fresh
gasoline and replace tuel filter,
Connect and tighten spark plug wire
C{ean engine air screen/fins
Clean/replace mufl{er
Check all wiring
Contact an authorized service facility,
Contact an authorized service facility.

t0
tl
12.
I3
14
15,

Excessive

.i..it .luJnlLiLi
/

Spark plug wire loose
Dirty engine air screentfins
Dirty/clogged muffler,
Loose or damaged wiring
Carburetor out of adjustment
Engine valves oLit of adjustment,

1,
2.

Worn, bent or {oose blade
Bent blade mandrel

3,

Loose/damaged

t0
11.
12
13
14
15,

1
2
3.

part(s)

27

Replace blade Tighten blade bolt
Replace blade mandre_
Tighten loose part(s) Replace damaged parts,

TROUBLESHOO

NG POINTS

CAUSE

CORRECTION

Engine continues to run
when operator leaves seat
with attachment clutch
engaged

1..

Faulty operator-safety presence control system

1

Check wiring, switches and connections, If not
corrected, contact an authorized service facility

Poor cut - uneven

1.
2

Worn, bent or loose blade..
Mower deck notlevel.

3
4

Buildup of grass, leaves, and trash under mower
Bent blade mandrel

5..

Clogged mower deck vent holes from buildup of
grass, leaves, and trash around mandrels

1
2
3
4
5

Repiace blade. Tighlen blade bolt.
Level mower deck
Clean underside of mower' housing
Replace blade mandrel
Clean around mandrels to open vent hoies

1

Obstruction

2
3.
4

Worn/damaged mower drive belt.
Frozen idler pulley
Frozen blade mandre!

t
2
3
4

Remove
Replace
Replace
Replace

!.,
2
3
4.

Engine speed too slow
Travel speed too fast
Wet grass,
Mower deck not level

1
2
3
4
5
6
7

Place throttle controf in "FAST" position.
Shift to slower speed.
Allow grass todry before mowing..
Level mower deck
Check tires for proper air pressure.
Replace/sharpen blade.. Tighten blade bolt.
Clean underside of mower housing,

8
9
10
1t

Replace mower drive bett
Reinstall blades sharp edge down
Replace with blades listed in this manual,
Clean around mandrels to open vent holes

Mower blades will not
rotate

in clutch mechanism

obstruction
mower drive bait
idler pulley.
blade mandrel

wit

Poor grass discharge

5,
6
7..
8
9
10
11.

Lowtuneven tire air pressure
Worn, bent orloose blade
Buildup of grass, leaves and trash under mower
Mower drive beltworn..
Btades improperly installed
Improper blades used.
Clogged mower deck vent holes from buildup of
grass, leaves, and trash around mandrels

ww

...........

Headlight(s) not working
(if so equipped)

t

Switch is "OFF"

2
3
4.
5.

Bulb(s) burned out..
Faulty light switch..
Loose or damaged wiring
Blown fuse

1
2
3
4
5

Turn swilch "ON".
Replace bulb(s).
Check/replace light switch..
Check wiring and connections
Replace fuse.

Battery will not charge

1
2.

Bad battery cell(s)
Poor cable connections

t
2

Replace battery
Check/clean all connections

3..
4.

Faulty regulator (if so equipped).
Faulty alternator.

3

Replace regulator
Replace alternator

1,.

Engine throttle control not set at "SLOW"
position for 30 seconds before stopping engine

1.

Engine "backfires"
when turning engine
"OFF"

4.

28

Move throttle control to "SLOW" position and attow
to idle for 30 seconds before stopping engine

TRACTOR

-- MODEL NUMBER

917.252540

SCHEMATIC
RED

11o

©

8LACK

m

_ATTERY

I

t

I
RED

RED

FUSE 30 AMP.

AMMETER
r

I
WHITE

STARTER
BLACK

.......

t-

la-@

,
i

1

0

}

I
f

SOLENOID

t

'

! C_--

L

J

CLUTCH / BRAKE
(PEDAL UP)

WH1TE

SEAT SWITCH

(NOT OCCUPIED)
I

t IGNITION SWITCH
WHITE

I
I

BLACK

-

I

i

I

L

I

T'--_

_AiLr_-EN'r
L

CUJTOH

"]

(CLUTCH OFF)

J

GROUNDING
CONNECTOR

@
BLACK

(_

I

SPARK
PLUG

IGNITION
UNIT

_1

AFTER FIRE SOLENOID

CHARGING
SYSTEM OUTPUT
3 AMP DC @ 3600 RPM

28 VOLTS AC MiN. @ 3600 RPM
(CHARGING
SYSTEM DISCONNECTED)

RED
S

LIGHTING

NOTE
M
[ICCt3

YOUR TRACTOR

B
EECZ]

SYSTEM

OUTPUT

5 AMP AC @ 3600 R.PM_.F-__

1S

,_

EQUIPPED WITH A SPECIAL
ALTERNATOR SYSTEM
THE LIGHTS ARE NOT
CONNECTED TO THE
BATTERY, BUT HAVE THEIR

L[zzzz]

OFF

ON "
.... START

M + G

'""' ...................
B'+'"'L _
B+ S + L

.........

"

i ALTERNATOR

\

/

!_
,4VOLTSAC
M,N_ 3600RPM(LtGHTSOF_')
IQ
!_
HEADLIGHTS
I _.......
_
_
__
;____
BECAUSE OF THIS, THE
14E-ADLK_T
!
_
1
BRIGHTNESS OF THE LIGHTS
SWtT_,.:I
L----{O O)-J
WILL CHANGE WITH ENGINE
(OFF)
SPEED. AT IDLE THE LIGHTS
WILL DIM. AS THE ENGINE IS
WIRING INSULATED CLIPS
SPEEDED UP, THE LIGHTS
WILL BECOME THEIR BRIGHTEST.
NOTE: IF WIRING INSULATED
/-_ 7
CLIPS WERE REMOVED FOR
SERVICING OF UNIT, THEY

OWN
ELECTRICAL
SOURCE,

IGNITION SWITCH
........
POSITION
CIRCUIT
............... ........................
........
......... ::

DIODE

NON-REMOVABLE
CONNECTIONS

_

REMOVABLE
CONNECTIONS

29

_'i

v T _J

T-

SHOULD BE REPLACED TO
PROPERLY SECURE YOUR WIRING°

REPAIR PARTS
TRACTOR

- - MODEL NUMBER 917.252540

ELECTRICAL

22
21

41

36 35
34

39

39

,,36

\
/

32

/
/

'I 31

/

\
/
/

30
I

/
I

-.,/

i

3O

REPAIR PARTS
TRACTOR

- - MODEL NUMBER

917.252540

ELECTRICAL

KEY
NO.

PART
NO°

1
2
3
4
6
7
8
9
15
16
19
20
21

144926
74760412
STD551025
STD551125
STD541025
109238X
144940
109596X
144935
145355
STD55t125
73350400
136850

22
24
25

4152J
4799J
146147

26
28
29
30
31
32
33
34
35
36
38
39
40
41
42
43
44
45
49
70

!08824X
4207J
121305X
144921
140400
141226
't40403
110712X
108236X
STD601005
140336
109553X
146057
71110412
131563
145673
73800400
121433X
11151000
142621

NOTE:

DESCRIPTION
Battery 12 Volt 30 Amp
Bolt, Hex Head 1/4-20 unc x 3/4
Washer
Washer
Nut
Tube, Plastic, 12"
Case, Battery
Clamp, Hose
Screw Cap Hex Nylon 3/8-16 x 1
Nut Nylon 3/8-16
Washer, Lock
Nut, Hex, Jam 1/4-20 UNC
Harness, Light Socket
(Includes Key # 33)
Bulb, Light
Cable, Battery, 6 Gauge, Red, 11"
Cable, Battery, 6 Gauge, Red, W/
16 Wit
Fuse, 30 Amp
Cable, Ground, 6 Gauge, Black, 12"
Switch, Plunger
Switch, ignition
Nut, Ignition
Cover, Key Switch
Key, Ignition
Switch, Light
Bracket, Clutch Switch
Screw
Bracket, Interlock Switch
Switch, Interlock, Clutch, 4 Terminal
Harness, Ignition
Bolt, Hex Head, Finn 1/4-20 x 3/4
Cover, Terminal, Red
Solenoid
Nut LockW/Insert
1/4-20 UNC
Ammeter Rectangular 6 Amp
Washer Lock internal Tooth 5/8
Harness Engine LTPL Koh Cmd_L
HL

All component dimensions given in UoS. inches
1 inch = 25.4 mm

31

REPAnR PARTS
TRACTOR-CHASSIS

MODEL NUMBER 917.252540

AND ENCLOSURES

5

26

25

21

18

I

29

14
19

I

t

28

i

26

I
I

33
10

26

32

14

REPAIR PARTS
TRACTOR
CHASSIS

- - MODEL NUMBER

917.252540

AND ENCLOSURES

KEY
NO.

PART
NO.

1
2
3
4
5
6
7
8
9
10
11
•13
14
15

145501
140356
17490612
19131216
146077
145206
126842X
126471X
146760X011
72140608
135464
126276X
17490608
74180512

16
17
18
19
21
22
24
25
26
27
28
29
30
31
33
34
35
38
39
40
100
--

STD541431
131445X459
126938X
17521312
122933X
124479X
STD523710
19131312
STD541437
17030814
140137
124029X
147310X459
139976
145244X459
145243X459
STD533707
139886
139887
139977
105037X
5479J

DESCRIPTION
Chassis Assembly
Drawbar
Screw, Thd. Roll. 3/8-16 x 3/4
Washer 13/32 x 3/4 x 16 Gauge
Bumper Snap-In
Saddle
Shield Ht Hood Kohl/Dia Engine
Clip Insulator .406 Mtg Hole
Dash
Bolt, Carriage 3/8-16 x 3/4
Panel, Dash, L_H_
Panel, Dash, R.H..
ScrewThdrot
3/8-16 x 1/2
Screw, Machine, Truss Head
5/16-18 UNC x 3/4
Nut
Hood Assembly
Bumper, Hood
Screw, Slid. Hex Hd_ w/PI Washer
Rivet, Ratchet, Nylon
Washer, Nylon ,28 x .75 x ..19
Bolt
Washer 13/32 x 13/t6 x 12 Gauge
Nut
Screw Spiderlock Hex Hd #8-7/8
Grill
Lens, Headlight Bar, Clear
Fender
Bracket, Fender Support
Footrest, L..H_
Footrest, R.H..
Bolt
Pivot Bracket Assembly, L.H..
Pivot Bracket Assembly, R_H.
Spacer Fender Raised LT
Strip Foam 18"
Plug, Button

NOTE: All component dimensions given in U.So inches
1 inch = 25.4 mm

33

REPAIR PARTS
TRACTOR

-- MODEL NUMBER

917,252540

DRIVE

67

5
i10

6
62
35

37

36
34

19
53

26
75

34

REPAIR PARTS
TRACTOR

-- MODEL NUMBER

917.252540

DRIVE

KEY
NO.
1
2
3
4
5
6
8
10
11
!3
14
15
19
21
22
24
25
26
27
28
29
30
31
32
34
35
36
37
38
39
40
41
42
44
45
46
47
48
49
50

PART
NO.
145602
146682
123666X
12000028
121520X
17490512
141003
76020416
105701X
74550412
STD551125
74780544
STD541437
106933X
130804
STD541237
106888X
STD551037
STD5612!0
145204
124236X
130807
127275X
STD523107
!22424X
t20183X
STD551062
STD571810
123674X
STD523727
4470J
109070X
19131312
105706X
110812X
12000039
127783
123789X
t23205X
STD523715

DESCRIPTION
Transaxle, Peerless, 6 Speed,
Model Number 930-057
Spring, Return, Brake
Pulley, Transaxle
Ring, Retainer
Strap, Torque
Screw, Thd., RoE 5/16-18 x 3/4
Lever, Shift
Pin, Cotter
Washer, Shift Plate
Bolt 1/4-28 UNF W/Patch Grade 8
Washer
Bolt, Hex Head 5/16-18 x 2_3/4
Nut
Knob
Rod, Brake
Nut
Spring, Brake Rod
Washer
Pin
Rod, Parking Brake
Cap, Parking Brake, Red
Bracket, Transaxle
Keeper, Belt, L_H.
Bolt
Shaft Assembly, Foot Pedal
Bearing, Nylon
Washer
Roll Pin
Pulley, Idler, Flat
Bolt
Spacer, Split .395 x °59
Keeper, Belt, Retainer
Washer 13/32 x 13/16 x 12 Gauge
Bearing, Nylon
Washer, Hardened
Ring, Klip
Pulley, Idler, V-Groove, Plastic
Betlcrank Assembly
Retainer, Belt
Bolt

KEY
NO.
51
52
53
55
56
57
58
59
61
62
63
64
65
66
70
72
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
96
!00
1t0
112
113

PART
NO.
STD541437
STD541431
105710X
105709X
STD523712
130801
127274X
140312
17490612
8883R
140186
M747810100
STD551143
129921
134683
19132012
!37057
!21749X
STD581075
123583X
121748X
2228M
145090
145092
123782X
19171216
145643
73530400
71208
19212016
12000008
139964
124346X
4497H
19111216
74760612
19091210
t27285X

NOTE:

35

DESCRIPTION
Nut Crown Lock 3/8-16 UNC
Nut Crown Lock 5/16-18 UNC
Link, Clutch
Spring, Clutch Return
Bolt Fin Hex 318-16 x I-1/4
V-Belt, Ground Drive
Keeper, Belt, R.H,
Keeper, Belt, Center Span
Screw, Thd. Roll 3/8-16 x 3/4
Cover, Pedal
PuIfey, Engine
Bolt, Hex
Washer
Keeper, Belt, Engine, L.H
Guide, Mower Drive Belt, RH,
Washer 13/32 x 1-1/4 x 12 Gauge
Spacer, Axle
Washer 25/32 x 1-1/4 x 16 Gauge
E-Ring
Key, Square 20 x .1845L1865
Washer 25/32 x 1-5/8 x 16 Gauge
Key Woodruff #9 3/16 x 3/4
Arm, Shift
Shaft Assembly
Spring, Torsion
Washer 17/32 x 3/4 x 16 Gauge
Tie Rod
Nut, Ny!ock
Bushing, Pivot
Washer
E-Ring
Console, Shift, 6 Speed, Ntlgnition
Nut, Self-Threading, Washer Hd 1/4
Retainer Spring 1" Zinc Cad
Washer 11!32 x 3/4 x 16 G&
Bolt, Fin Hex 3/8-16 UNC x 3/4
Washer 9/32 x 3/4 x 10 Gauge
Strap Torque LT

All component dimensions given in U..S. inches
1 inch = 25.4 mm

REPAIR PARTS
TRACTOR
STEERING

- - MODEL NUMBER

917.252540

ASSEMBLY

b!-,
t

I

I
I

I

46
47

117

16

32

26
43

12
t

28
30

36

I
I
\
\

REPAIR PARTS
TRACTOR
STEERING

- - MODEL NUiVIBER 917.252540

ASSEMBLY

KEY
NO.

PART
NO.

1
2
3
4
5
6
7
8
9
10
11
12
13
'14
15
16
17
18
19
2O
21
22

121472X
142033
135227
135228
6266H
121748X
19272O16
12000029
3366R
130468
STD551137
73610600
110438X
74011056
73901000
132624
132614
57079
124035X
126684X
STD551125
71070410

23
24
25
26
27
28
29
3O
32
36
37
38
39
4O
41
42
43
46
47
62

127501
109816X
124036X
126847X
136874
19131416
17490612
STD561210
130465
132196
STD611005
126805X
19133808
STD541537
104820X
124417X
121749X
121232X
6855M
149684

DESCRIPTION
Steering Wheel
Front Axte Assembly
Spindte Assembly, Loll.
Spindle Assembly, R.H.
Bearing, Race, Thrust, Hardened
Washer 25/32 x 1-5/8 x 16 Gauge
Washer 27/32 x 1_1/4 x 16 Gauge
Ring, Klip
Bearing, Steering Column
Link, Drag
Washer, Lock
Nut, Hex, Fin. 3/8-24 UNF
Spacer, Bearing, Front Axle
Bolt, Hex Head 5/8-11 UNC x 3-1/2
Nut, Lock, Flange 5/8-11 UNC
Pin, Axle 5/8 x 1.55/1.54
Shaft Assembly, Steering
Washer, Thrust .515 x ,.750 x .033
Support, Shaft
Washer, Shim 1/4 x 5/8 x .062
Washer
Screw, Hex Socket Head
1/4-20 x 5/8
Pittman Shaft Assembly
Nyliner, Snap-In
Bracket, Steering
Bushing, Link, Drag
Gear, Sector
Washer 13/32 x 7/8 x 16 Gauge
Screw, Thd, Roll 3/8-16 x 3/4
Pin
Rod, Tie
Bushing, Steering
Screw
Insert, Steering Wheel
Washer 13/32 x 2-3/8 x 8 Gauge
Gripco Nut
Adaptor, Steering Wheel
Boot, Steering Shaft
Washer 25/32 x 1-1/4 x 16 Gauge
Cap, Spindle
Fitting, Grease
Kit, Steering Assembty

NOTE: All component dimensions given in U..Soinches
I inch = 25..4 mm

37

REPABR PARTS
TRACTOR

-- MODEL NUMBER

917.252540

SEAT ASSEMBLY

10

®

6

21

5

115
23

"_\ 13
17

KEY
NO.

PART
NO.

!
2
3
4
5
6
7
8
9
10
12
t3
14

140123
140551
STD523710
19131610
145006
STD541437
124181X
17490616
19131614
140552
121246 X
121248 X
72050411

_.
12

KEY
NO.

DESCRIPTION
Seat
Bracket, Pivot, Seat
Bolt
Washer 13/32 x 1 x 10 Gauge
Clip, Push-ln Hinged
Nut
Spring, Seat
Sc_ew, Thd., RoE 3/8-!6 x 1
Washer 13/32 x I x i4 Gauge
Pan, Seat
Bracket, Switch Mounting
Bushing, Snap
Bolt, Carriage 1/4-20 x 1-3/8

PART
NO.

15
16
17
21
22
23

134300
121250X
123976X
139888
STD541431
74780814

24
25
26

19171912
127018X
STD551150

DESCRIPTION
Spacer, Split .28 x ..88
Spring
Locknut, Flange 1/4 Grade 5
Bolt, Shoulder 5/16-18 UNC
Nut
Bolt, Hex Head, Fin.
1/2-13 x 7/8 Grade 5
Washer 17/32 x 1-3/t6 x t2 Gauge
Bolt, Shoulder 5/16-18 x .62
Washer, Lock

NOTE: Atl component dimensions given in U.S. inches
1 inch = 25.4 mm

38

REPAUR PARTS
TRACTOR

- - MODEL NUMBER

917.252540

DECALS
9

13

20

6

3

18

7

7

/

18

4

16

10
22

19
21

11

8

12

13

2
14
17

KEY
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13

PART
NO,
138955
1211363
143735
143736
132674
133644
142241
133178
128314
137537
4900J
146046
131473

WHEELS

15

KEY
NO,

DESCRIPTION
Decal
Decal
Decal
Decal
Decal
Decal
Decal
Decal
Decal
Decal
Decal
Decal,
Decal,

Operating Instruction
Koh114.5Cmd_L Sears
Hood, R_H,.
Hood, L.H,,
Grill, LT4000
Customer Maintenance
Side Panel, Kohler
Mower, 3 In One
Fender, Craftsman
Caution, English
Clutch/Brake, English
V-Belt Drive Schematic
Chassis, 6 Speed/42"

& TIRES

PART
NO.

14
15
16
17
18

136832
145245
140837
133179
146813

19
20
21
22
--- -

131265
132266
145003
146833
145247
138311
147191
147192

KEY
NO.
1
2
3
4

5,8
4,10
7
;,9
11

PART
NO,
59192
65139
106222X
59904

5
6
7
8
9
10

106732X427
278H
9040H
106108X427
122082X
7152J

11

104757X
144334

NOTE:

39

DESCRIPTION
Decal, V-Belt Schematic
Pad Footrest Rbr Sq Craftsman
Decal, Parking Brake Saddle
Decal, Mower QC System
Decal, Ins,. Hood 14.5HP OHV
White
Decal, Lightbox, Grill
Decal, Insert Strg Std Auto USA
Decal, Battery Dan/Poi Srs
Decal, Battery Wet Front Sears
Fastener Pop In Footrest
Decal, Lift Handle
Owner's Manual, English
Owner's Manual, Spanish

DESCRIPTION
Valve Cap, Tire
Stem, Valve
Tire, Front
Tube, Front Tire
(Not Provided, Service item Only)
Rim, Front
Fitting, Grease (Front Wheel Only)
Bearing, Flange (Front Wheel Only)
Rim, Rear
Tire, Rear
Tube, Rear Tire
(Not Provided, Service Item Only)
Cap, Axle
Sealant, Tire (10 ozo Tube)

Atl component dimensions
1 inch = 25,4 mm

given in U oS inches

REPAIR PARTS
TRACTOR

- - MODEL NUMBER

917.252540

ENGINE

14

15

4

6

33
31

37
29

\
OPTIONAL

23

EQUIPMENT

Spark Arrester

40

REPAURPARTS
TRACTOR

-- MODEL NUMBER

917.252540

ENGINE

KEY
NO.
1
2

PART
NO.
132760
17720410

3
4
14
15
16
23
24
29
31
32
33
37
38

147337
137350
13280328
13200300
STD551231
128953X
STD601005
137180
109202X
123549X
123487X
137040
---

40
44

124028X
17490412

46
62
77
79
80
81

19091416
STD551131
19101216
M740i08025
747605O8
735104O0

NOTE:

DESCRIPTION
Control, Throttle
Screw, Hex Head, Thread Cutting
1/4-20 x 5/8
Engine, Kohfer, 14.5 Cmd_L 5&3 SRS
Muffler
Nipple, Pipe 3/8 NPT x 3-1/2
Elbow, Standard 90 °, 3/8-t8 NPT
Washer
Shield, Heat
Screw
Arrestor, Spark
Tank, Fuel
Cap Assembly, Fuel Tank, Vented
Clamp, Hose
Line, Fuel
Plug, Oil Drain
(Order From Engine Manufacturer)
Bushing, Snap, Fuel Line
Screw, Hex Washer Head, Thdo, Roll.
1/4-20 x 3/4
Washer 9/32 x 7/8 x 16 Gauge
Washer, Lock
Washer 5/16 x 3/4 x 16 Ga,.
Bolt Hex
Bolt Hex Hd 5/t6-18 UNC x 1/2
Nut Heps Flex 1/4-20 UNC

All component dimensions given in U.S,. inches
1 inch = 25.4 mm

41

REPAIR PARTS
TRACTOR
MOWER

- - MODEL NUMBER

917.252540

LIFT

28

/

27
26
24

23

8

22
5

i!

II

i

21

iI

!

30

13

\

4
6

6

11

5

13
19
_13

20

1

32

2O
15

161718
20

19
15
32

42

REPAIR PARTS
TRACTOR
MOWER

- - MODEL NUMBER

917.252540

LIFT

KEY
NO.

PART
NO.

1
2
3
4
5
6
7
8
10
11
12
13
15
i6
17
18

136973
122507X
105767X
12000002
19211621
120183X
125631X
122365X
1225!2X
!39865
139866
4939M
127218
73350800
130171
73800800

19
20
21
22
23
24
25
26
27
28
29
30
31
32

139868
3t46R
19151216
12000037
110807X
19131016
2876H
76020308
126971X
73350600
138057
110810X
140302
73540600

NOTE:

DESCRIPTION
Lift Lever InnerWire Assembly
Shaft Assembly, Lift
Pin, Groove
E-Ring
Washer 21/32x 1 x21 Gauge
Bearing, Nylon
Grip, Handle, Fluted
Button, Plunger, Red
Spring
Link, Lift, LH.
Link, Lift, R..Ho
Retainer Spring
Link, Front
Nut, Hex, Jam 1/2-13 UNC
Trunnion
Locknut, Hex, with Washer Insert
1/2-13 UNC
Arm, Suspension, Rear
Retainer Spring
Washer 15/32 x 3/4 x 16 Gauge
Ring, Klip
Nut, Special
Washer t3/32 x 5/8 x 16 Gauge
Spring
Pin, Cotter 3/32 x 1/2
Rod, Adjust, Lift
Nut, Hex, Jam 3/8-16 UNC
Knob, infinite Height Adjustment
Trunnion, Depth Stop
Bearing, Pvt, Lift Spherical
Nut, Crownlock 3/8-24

All component dimensions given in U.S_ inches
1 inch = 25.4 mm

43

REPAIR PARTS
TRACTOR
MOWER

- - MODEL NUMBER

917.252540

DECK
76

77

68

75
74

73

4O

105
102
34
33
32

106
_"_"-104
105/ ._
106"

23 24

\

2
28
29
18

44

27

REPAnR PARTS
TRACTOR
MOWER

- - MODEL NUMBER

917.252540

DECK

KEY
NO.

PART
NO.

1
2
3
4
5
6
8
9
10
11
12
13

144393
STD533107
138O17
138440
STD624008
130832
85O857
STD551137
140296
134149
129895
137645

14 128774
15 110485X
16 140329
17 72110610
18 72140505
19 132827
20 136888
21 STD54t43I
22
134753
23
131267
24
105304X
25
123713X
26 110452X
27 130968
28 19111016
29 131491
30 138776
31 129963
32 129861
33
137266
34 STD533717
35 133835
36 131494
37 19131316
40 STD541437
41 133551
43
140083
44
140088
45 STD624003
46
137729
48 133944
49 133940
50 131340
51 STD5414t0
52 139888
53 131845

DESCRIPTION
Mower Housing
Bolt
Bracket Assembly,Sway Bar, Front
Bracket Assembly, Sway Bar
Retainer Spring
Arm, Suspension, Rear
Bolt, Hex 3/8-24 x 1,25 Grade 8
Washer, Lock
Washer, Hardened
Blade, Mulching
Bearing, Ball
Shaft Assembly, Mandrel, Vented
(Includes Key Number 6)
Housing, Mandrel, Vented
Bearing, Ball, Mandrel
Stripper, Vented Mower Deck
Bolt, Carriage 3/8-16 x 1-1/4
Bolt, Carriage 5/16-18 x 5/8
Bolt, Shoulder
Baffle, Vortex
Nut Crownlock 5/16-18 UNC
Stiffener Bracket
Bracket, Deflector
Cap, Sleeve
Spring, Torsion, Deflector
Nut, Push
Shield, Deflector
Washer 11/32 x 5/8 x 16 Gauge
Rod, Hinge
Screw Thdrol Hex Head Zinc Mwr
Washer, Spacer
Pulley, Mandrel
Nut, Toplock, Flanged
Bolt
Fastner, Christmas Tree
Pulley, Idler, Fiat
Washer 13/32 x 13/16 x 16 Gauge
Nut Crowntock 3/8-16 UNC
Rod, Pivot, with Nibs
Rod, Clutch, Secondary, with Nibs
Guard, Mandrel, L,H.
Retainer
Screw, Thd, Roll 1/4-20 x 5/8
Washer, Hardened
Roller Assembly, Cam Follower
Bolt, Shoulder #10-24 Grade 5
Locknut
Bolt, Shoulder 5/16-18 UNC
Arm Assembly, Pad, Brake

KEY
NO.

PART
NO.

54
55
56
58
59
67
68
71
72
73
74
75
76
77
78
79
80
8!
82
83
84
85
92
101
102
103
104
105
106
111
112
113
1t4
115
1I 6
1t7
118
119
121
--

133943
140084
122052X
140086
141043
106932X
144200
142427
131870
127847
121748X
12O00029
128903
127845
14O334
127498
128759
73350600
142028
120958X
144394
72140620
STD541437
13642O
71161010
19061216
STD551110
130758
2029J
140353
132262
17490512
73510500
72110504
137644
133957
73930600
19121414
143723
130794

--

145411

NOTE:

45

DESCRIPTION
Washer, Hardened
Arm, Idler
Spacer, Retainer
Spring, Torsion Brakes
Guard, TUV Idler
Knob, Round 3/8-16 UNC
V-Belt
Rod, Clutch, Primary, with Nibs
Spring, Return
Arm, Clutch, Secondary
Washer 25/32 x 1-5/8 x 16 Gauge
Ring, Klip
Bolt, Shoulder 3/8-16 UNC x 1,44
Keeper, Spring
Arm, Clutch, Primary
Bushing, Large, Brass
Spring, Mower Clutch
Nut, Hex Jam 3/8-16 Unc
Trunnion, Adj,
Washer Sintered
Keeper Belt Idler Fixed
Bolt Carriage 3/8-16 x 2-1/2 Gr.. 5
Nut
Mutcher Cover
Screw
Washer #'10
Washer, Lock
Latch Assembly, Bagger
Nut, Weld
Bracket, Gauge, Wheel L,.H..
Bracket, Gauge. Wheel R..H,
Screw Thdrol 5/16-18 x 3/4
Nut, Hex, Keps 5/16q8 UNC
Bolt, Carriage 5/16 UNC x t/2
Bolt, Shoulder
Wheel, Gauge
Nut, Centerlock 3/8-16
Washer 3/8 x 7/8 x 14 Gauge
Bracket
Mandrel Assembly (includes Key
Numbers 8-10, 12-15, 31 and 32)
Mower Deck, Complete (Standard
Deck, Order Separately Mulcher
Plate and Gauge Wheel
Components, Key Nos,. 101-106
and 11 t-'121 )

All component dimensions
1 inch = 25,,4 mm

given in U,S, inches

REPAIR PARTS
TRACTOR
PEERLESS

TRANSAXLE

- MODEL

,. - MODEL NUMBER
NUMBER

917.252540

930-057

8
!

8

/

/
L

77

5

18
62
3O
23

/
13

15

36
44
45
42A
/

46

&..,%

REPARR PARTS
TRACTOR
PEERLESS

TRANSAXLE

- MODEL

- - MODEL NUMBER
NUMBER

REF PART
NO, NO.

DESCRIPTION

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
17
18
20
21
22
23
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
42A
43
44

Transaxle Cover
Needle Bearing
Transaxle Case
Countershaft
Output Shaft & Pinion
Output Gear, 35 Teeth
Spur Gear, 15 Teeth, Steel
Shift Key
Shift Collar
Shift Rod & Fork
Bevel Gear, 42 Teeth
Input Bevel Pinion
Bevel Gear, 16 Teeth
Differential Pinion
Ring Gear
Drive Pin
Spacer
Steel Ball, 5/16" Diameter
Set Screw 3/8-16 x 3/8
Spring
Seal Ring
Screw 1/4-20 x !-1/4
Retaining Ring, Package of 2
Retaining Ring
Retaining Ring
Washer
Washer
Washer
"O" Ring
Square Cut Ring
Flanged Bushing
Flanged Bushing
Brake Disk
Brake Pad Plate
Brake Pad, Package of 2
Dowel Pin
Washer
Brake Lever
Screw 1/4-20 x 1-1/4
Screw 1/4-20 x 2-1/4
Locknut 5/16-24
Brake Pad Holder

772108A
780086
770102A
776260
776219B
778139
778136
792136A
784352
784355
778229
778113A
778221
778068
778260
786139
786102
792077
792078
792079
788061
792073
792125
792035
788040
780072
780t08
780001
792001
788051
780105A
780118A
790003
790007
799021
786026
792076A
790079
792073 _
792085A
792075
790025

917.252540

930-057

REF PART
NO, NO.
45
46
47
48
49
50
51
52
53
54
56
57
58
59
60
61
65
66
67
68
69
70
7t
72
72A
76
77

786066
786086
774690
774691
778215
778125
778124A
778123A
778122A
778273
778230
778151
778126A
778127A
778128A
778163
780109
776I 35
776315A
786116
780051
786118
788069
792165
788091
780090
788078A

79
81

792144
786081

82
83
90
103
104
150

786082
786123
788067B
792166
792167
510334

DESCRIPTION
Spacer
Brake Lever Bracket
Axle, 11-15/16" Long
Axle, t6-1/2" Long
Spur Gear, 37 Teeth, Steel
Spur Gear, 35 Teeth
Spur Gear, 30 Teeth
Spur Gear, 25 Teeth
Spur Gear, 22 Teeth
Spur Gear, 19 Teeth, Steel
Spur Gear, 12 Teeth, Steel
Spur Gear, 15 Teeth
Spur Gear, 20 Teeth
Spur Gear, 25 Teeth
Spur Gear, 28 Teeth
Spur Gear, 31 Teeth
Washer
Input Shaft
Shifter and Brake Shaft
Disk
Washer
Spacer
Square Cut Ring
Threaded Plug 9!16-18
"O" Ring
Washer
Inverted Retaining Ring,
Package of 2
Spring
Roller Chain,
Number 41 Chain, 24 Links
Sprocket, 9 Teeth
Reverse Sprocket, 18 Teeth
Grease, Bentonite, 32 Ounce Bottle
Screw 1/4-20 x 2
Locknut 1/4-20
Gasket Eliminator, Loctite #515

Parts must be ordered from Tecumseh Products Coo
NOTE:

47

All component dimensions given in U,,S, inches
1 inch = 254 mm

REPARRPARTS
TRACTOR
KOHLER

ENGINE

- MODEL

-- MODEL NUMBER

NUMBER

917.252540

CV15S, TYPE NUMBER

PS-41519
i,iiiiiiii ii

A,R,.TAKE
I

BLOWER

HOUSING

AND

BAFFLES

7
2

3

@

_6
,.%

ENGINE
1!

CONTROLS

_8

2

3

/
CRANKSH A,F,T,
.....
I

4

6

48

REPABR PARTS
TRACTOR
KOHLER

ENGINE

- MODEL

- - MODEL NUMBER

NUMBER

CV15S, TYPE NUMBER

1
2
3
4
5
6
7
8

25 341 02
t2 096 24
12 083 08
12 100 01
X-25-63
12 083 05
12 313 04
12 O94 O9

9
10
11

12 072 03
12 086 01
1204102

PS-41519

ENGINE CONTROLS

AIR INTAKE
KEY PART
NO. NO.

917.252540

KEY PART
NO. NO.

DESCRIPTION
Knob, Air Cleaner Cover
Cover, Air Cleaner
Precleaner Element
Wing Nut
Washer, Plain 1/4
Element, Air Cleaner (includes #7)
Grommet
Base, Air Cleaner
(Includes Key Numbers 9 and 10)
Stud, Mounting Plate
Screw, Mounting Plate Stud (2)
Gasket, Air Cleaner

NOT ILLUSTRATED
- - 12 1 t3 53
Decal, Air Cleaner

1
2
3
4
5

12 079 07
12 237 01
SM-0645016
SM-0545016
12 536 01

6
7
8
9
10
11

SM-0443025
12 089 11
12 089 23
12 089 19
SM-0641060
SM_0642025

12
13
14
15

12 090 05
25 t58 11
1207901
25 158 08

DESCRIPTION
Linkage, Choke
Clamp, Cable
Screw, Hex Head M6 x 1..0 x 16 (2)
Screw, Cable Clamp M5 x o8 x 16
Control, Speed Assembly (Includes
Key Numbers 6 through 8)
Screw
Spring, Choke Adjust
Spring, Choke Return
Spring, Governor
Nut, Governor Arm M6 x 1.0
Screw, Governor Arm
M6 x 140 x 25
Lever, Governor
Bushing
Linkage, Throttle
Bushing

CRANKSHAFT
KEY PART
NO. NO.
1
2

!2 014 02
12 13901

EXHAUST
DESCRIPTION
KEY PART
NO. NO.

Crankshaft
Plug, Cup

BLOWER HOUSING AND BAFFLES
KEY PART
NO. NO.
1
2
3
4
5
6
7

M-0545010
12 146 07
12 O27 25
12 063 05
12 313 03
12 063 08
12 063 01

DESCRIPTION
Screw, Mounting M5 x 0.8 x 10 (13)
Plate, Blower Housing
Housing, Blower
Baffle, Carburetor
Grommet, Blower Housing
Baffle, Cylinder Head
Baffle, Cylinder

1

M_0829033

2
3
4
5
6

12 041 03
M-0841080
12 126 11
12 445 01
M_0645025

DESCRIPTION
Stud, Exhaust Manifold
M8 x 1.25 x 20 (2)
Gasket, Exhaust Manifold
Nut, Muffler Mounting M8 x 1.25 (2)
Bracket, Muffler
Strap, Lifting
Screw, Lifting Strap
M6 x 1.0 x 25 (2)

NOTILLUSTRATED
KEY PART
NO. NO.
---

NOT ILLUSTRATED
-12 113 63
Decal, Horsepower

125217
12 755 0t

DESCRIPTION
Short Block
Gasket Set

RPM Settings: Low Speed: 1500-2000
High Speed: 3200-3400
NOTE:

49

All component dimensions given in U.S. inches
I inch = 254 mm

REPAIR PARTS
TRACTOR
KOHLER

ENGINE-

MODEL

- - MODEL NUMBER

NUMBER

CV15S,

TYPE

917.252540

NUMBER

PS-41519

.....
F0,'SYs+E
I
(_8
18_-6

9
17..%
16-... _)
14__

4

__°

_

/
/

5

21

12

/

4

--25

2

/
31

__o
29

CYLINDER

HEAD,

VALVE

AND

BREATHER

/
28

J

5

11

5O

REPAIR PARTS
TRACTOR
KOHLER

ENGINE

- MODEL

- - MODEL

NUMBER

CV15S,

FUEL SYSTEM
KEY PART
NO. NO.
1
2
3

!2 853 26
12 041 02
12 053 32

4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26

12 041 01
12 265 01
X-426-9
25 353 10
25 05O O2
47154 0t
12 086 07
12 431 01
12 368 01
12 089 09
12 086 04
12 089 09
I2 146 O3
25 086 27
12 144 09
12 144 08
12 O89 10
12 146 02
12 337 01
12 757 02
12 041 05
12 104 01
12 757 09

27
28
29
3O
3I

12 041 06
SM-0641060
X-25-63
X-22q1
M-0629122

NOT ILLUSTRATED
12 041 01
w
12 757 03
12 755 09
12 518 05
41 518 34

NUMBER

917.252540

TYPE NUMBER

PS-41519

CYLINDER HEAD, VALVE AND BREATHER
KEY PART
NO. NO.

DESCRIPTION
Kit, Carburetor (Includes #2 thru 4)
Gasket, Air Cleaner
Carburetor Assembly
(For Information Only - Not
Available Separately)
(includes Key Numbers 12 thru 27)
Gasket, Carburetor (2)
Deflector, Heat
Clamp, Hose (2)
Line, Fuel, 9"
Filter, Fuel
Clip, Cable
Screw, Ground Wire
Sleeve, Insulating
Needle, idle, Fuel Adjust
Spring, Idle Fuel
Screw, Idle Speed Adjust
Spring, Idle Speed
Plate, Throttle
Screw, Throttle Plate (2)
Shaft, Throttle with Lever and Seal
Shaft, Choke
Spring, Choke Return
Plate, Choke
Jet, Main
Kit, Float
Gasket, Bowl
Bowl, Fuel
Kit, Solenoid Assembly
(Includes Key Number 7)
Gasket, Bowl Retainer Screw
Nut, Carburetor M6 x ln0 (2)
Washer, Plain 1/4
Washer, Internal Tooth 1/4
Stud, Carburetor M6 x 1o0 x 110 (2)

1
2
3
4
5
6
7
8

12
12
I2
12
12
12
12
12
12
12

3!8
351
411
041
017
017
016
016
112
086

DESCRIPTION
02
01
01
10
01
02
01
02
13
15

9
10
11
12
13
14
15
16

I2 089 15
12 173 01
12 755 O3
12 089 01
X426-9
12 326 03
12 468 05
M-0645020

17
18
19
20
21
22

12 O96 O7
M-0640034
24 194 01
24 186 03
12 146 13
M-0545010

23
24

12 018 01
24 402 03

Head, Cylinder
Lifter, Valve (2)
Rod, Push (2)
Gasket, Cylinder Head
Valve, Intake, Standard Size
Valve, Intake, _25" Oversize
Valve. Exhaust, Standard
Valve, Exhaust, .25" Oversize
Spacer, Head Bolt Exhaust Port
Screw, Cylinder Head
M10 x 1.5 x 80 (5)
Spring, Exhaust Valve
Cap, Valve Spring (2)
Kit, Retainer (2)
Spring, Intake Valve
Clamp, Hose (2)
Hose, Breather
Washer, Plain
Screw, Valve Cover
M6 x 1,O x 20 (5)
Cover, Valve with Nipple
Screw, Rocker Arm M6 x 1 x 34 (2)
Pivot, Rocker Arm (2)
Arm, Rocker (2)
Plate, Guide
Screw, Breather Reed Retainer
M5 x 0.8 x 10
Retainer, Breather Reed
Reed, Breather

NOT ILLUSTRATED
-75560
Kit, Cylinder Head
NOTE: All component dimensions
1 inch = 25.4 mm

Gasket, Carburetor
Kit, Carburetor Repair
Kit, High Altitude Jet
Lead, Solenoid, Black, 5", 14
Gauge, Uninsulated Push*On Tabs
Lead, Ground, Green, 5", 18 Gauge
Insulated Grip Barrel Eyelets

5'1

given in US. inches

REPAURPARTS
TRACTOR
KOHLER

IGNITION

ENGINE

- MODEL

t ELECTRICAL
,,,u

i

iii

1

- - MODEL NUMBER 917.252540

NUMBER

CV15S, TYPE NUMBER

PS-41519

OIL PAN / LUBRICATION

,i,ui

llrH,ll

i

i,i i ii

,
C_2

17 ...,_

\

il

J

\_'_

__o

STA.T,.Q
......................
S_STE.
I

CRANK:CAS,E,,,,!

ll,llli, ii ill

............

5_

52

REPARR ,PARTS
TRACTOR
KOHLER

ENGINE

- MODEL

- - MODEL NUMBER

NUMBER

9!7.252540

CV15S, TYPE NUMBER

IGNITION 1 ELECTRICAL

CRANKCASE

KEY PART
NO. NO.

KEY PART
NO. NO.

1
2
3
4
5
6
7
8
9
10

12 086 14
12 468 03
24 162 03
M-0639016
12 112 01
1215702
X_42-15
12 025 25
41 155 02
M-0548025

11

M-0545010

12
13
14
15
'16
17

12 154 02
12 085 03
12 132 02
X-728-1
12 584 01
SM-0545020

DESCRIPTION

1
2
3
4
5
6
7
8

Screw, Flywheel Mt0 x 1.5 x 45.8
Washer, Flywheel
Screen, Grass
Screw, Fan M6 x 1 x 13 (4)
Spacer, Fan (4)
Fan
Key
Flywheel Assembly
Connector (4 Contact)
Screw, Stator Mounting
M5 x &8 x 25 (2)
Screw, Stator Harness Clip
M5 x 0.8 x 10 (2)
Clip, Stator Harness
Stator Assembly
Spark Plug
Clip, Cable
Module, Ignition
Screw, Ignition Module
M5 x 0.8 x 20 (2)

12 422 11
12 422 12
12 422 13
12 422 07
9
10
11
12

OIL PAN / LUBRICATION

13

KEY PART
NO. NO.

14
15
16
17
18
19
20
21
22
23

2
3
4
5
6
7
8
9
10
11

25 755 13
12 153 03
12 15302
12 123 04
SM-0545020
12 15301
25 162 07
12 096 03
SM-0545016
M-1039025

12
13
14
15
16
17
18
t9
20
21

12 126 02
!2 089 03
124620'1
12 2O8 01
12 050 01
X-75-10
12 393 01
12 032 04
12 096 02
SM-0545016

22
23
24

12 032 03
SM-0839045
12 199 30

12 032 03
1252217
12 445 02
M-0839025
12 380 03
!2 010 02
12 089 18
t2 422 08
12 422 09
!2 422 10

NOT ILLUSTRATED
12 518 01
Lead, White, Ground To Kill (19",
18 Gauge, Fulty Insulated Push-on
Tab and Uninsulated Push-on Tab
Terminals)
51 755 01
Kit, Diode

12 038 01

PS-41519

DESCRIPTION
Dipstick Assembly
(includes Key Numbers 2 and 3)
Kit, Oil Fill Cap (Includes Key #3)
O-Ring, Dipstick
O-Ring, Upper Oil Fill Tube
Tube, Oil Fill
Screw, Oil Fill Tube M5 x 0..8 x 20
O-Ring, Lower Oil Fill Tube
Screen, Oil Pick-up
Cover, Oil Pick-up Screen
Screw, Screen Cover
Screw, Oit Pump Relief Valve
Bracket M10 x 1.5 x 25
Bracket, Oil Pump Relief Valve
Spring, Oil Pump Relief Valve
Piston, Oil Pump Relief Valve
Body, Oil Pump Relief Valve
Filter, Oil
Plug, Square Head, Solid 3/8 NPTF
Oil Pump Assembly
O-Ring, Oil Pump Cover
Cover, Oil Pump
Screw, Oil Pump Cover
M5 x 0.8 x 16 (3)
Seal, Oil (P.T_O.. End)
Screw, Oil Pan M8 x 1.25 x 45 (12)
Pan, Oil

1214419
12 874 07
12 874 08
12 874 09
12 018 O2
12 !08 07
12108 08
12108 09
12 O67 25
12 067 06
12 380 01
12 043 05
SM-0631005
12 144 02
52 139 09
12144 01
SM-0631015
12 032 01
X-25-102
12 380 04

DESCRIPTION
Seal, Crankshaft
Block, Cylinder (Use Short Block)
Strap, Lifting
Screw, Lifting Strap M8 x 1o25 x 22
Dowel, Locating (4)
Camshaft Assembly (Includes #7)
Spring, Actuating
Shim, Camshaft, Blue
Shim Camshaft, Green
(as required)
Shim, Camshaft, Yellow
(as required)
Shim, Camshaft, Red
(as required)
Shim, Camshaft, Grey
(as required)
Shim, Camshaft, Black
(as required)
Shim, Camshaft, White
(as required)
Shaft, Balance
Piston w/Ring Set, Standard
Piston w/Ring Set _25" Oversize
Piston w/Ring Set .50" Oversize
Retainer, Piston Pin (2)
Ring Set, Standard
Ring Set ..25" Oversize
Ring Set .50" Oversize
Connecting Rod, Standard
Connecting Rod ..25"Oversize
Pin, Governor Regulating
Gear, Governor Assembly
Washer, Governor Gear Thrust
Shaft, Governor Gear
Plug, Cup
Shaft, Governor Cross
Washer, Governor Shaft
Seal, Governor Cross Shaft
Washer, Plain 1/4
Pin, Governor Hitch

STARTING SYSTEM
KEY PART
NO. NO,
1

M-0839070

2

12 098 13

3
4
5
6
7
8

12
12
45
82
I2
12

755 53
227 05
'170 03
755 28
227 11
086 25

DESCRIPTION
Screw, Starter
M8 x 1.25 x 70 (2)
Starter Assembly
(Includes Key Numbers 3 thru 8)
Kit, Drive
Cap, Drive End
Armature
Kit, Brush and Spring
End Cap, Commutator
Screw (2)

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

53

SERVICE

OTES

54

SUGGESTED

GUIDE FOR SiGHTiNG SLOPES FOR SAFE OPERATION

ONLY RIDE UP AND DOWN HILL,
NOT ACROSS HILL
SIGHTING
GUIDE

SIGHT AND HOLD THIS LEVEL WITH
SKY LINE OR TREE.
O'1

15 ° MAX.

i iiii, I,

_1 A
li_ A_
Ii_ _
lil
1_

,.

'!I II[I

lllLllllllll[l

I I' II UI!!LIJ

r

I II

!
l

Operate your Tractor up and down the face of slopes (not
qreater than 15°), never across the face. Make turns gradually to prevent tipping or loss of control. Exercise extreme
caution when changing direction on slopes.
I J[

®

OWNER'S
MANUAL

14.5 HP
ELECTRIC START
3 in One Convertible
42" MOWER
6 SPEED TRANSAXLE
LAWN TRACTOR

MODEL NO.
917.252540

Each tractor has its own model number., Each engine has
its own model number.
The model number for your tractor will be found on the
model plate located under the seat_
The model number for your engine will be found on the
blower housing of the engine.
All parts listed herein may be ordered from any Sears,
Roebuck and Co. Service Center/Department and most Retail Stores°

IF YOU NEED
REPAIR SERVICE
OR PARTS:

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE
FOLLOWING INFORMATION:
FOR REPAIR SERVICE, CALL
THIS TOLL FREE NUMBER:

1-800-4-REPAIR

o PRODUCT- TRACTOR
° MODEL NUMBER - 917.252540

(I -800-473-7247)

° ENGINE MODEL NO. - CV15-41519

FOR REPLACEMENT PARTS
INFORMATION AND
ORDERING, CALL THIS
TOLL FREE NUMBER:

1-800-FON-PART
(1-800-366-7278)
FOR CONSUMER ASSISTANCE
HOT LINE, CALL THIS
TOLL FREE NUMBER:

= PART NUMBER
• PART DESCRIPTION
Your Sears merchandise has added value when you
consider Sears has service units nationwide staffed with
Sears trained technicians..,
professional
technicians
specifically trained to insure that we meet our pledge to
you, we service what we sell.,

1-800-659-5917

147191

Rev. 2

07.19.95

KFSW

Printed in U.S,A.
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 56
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 4, 0, 0, 13
Create Date                     : Fri Sep 12 01:20:22 2008
Author                          : 
Title                           : 
Subject                         :
EXIF Metadata provided by EXIF.tools

Navigation menu