Secure Wireless PIR315 Wireless Motion Sensor User Manual P983 indd

Download:
Mirror Download [FCC.gov]
Document ID	1491716
Application ID	XVzcWyYQKftPRplSuW9ypQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	Yes
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	17.16kB (214518 bits)
Date Submitted	2011-06-17 00:00:00
Date Available	2011-06-28 00:00:00
Creation Date	2011-06-24 09:46:33
Producing Software	Acrobat Distiller 9.4.5 (Windows)
Document Lastmod	2011-06-24 09:47:05
Document Title	P983.indd
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Copyright © 2011 Linear LLC

PRINTER’S INSTRUCTIONS:
INSTR,INSTL,DXS-55AF - FILE NAME: P983 X10 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - SIDE 1 OF 2
DXS-55AF
ALARMFORCE
PRODUCT DESCRIPTION
PIR FEATURES
The DXS-55AF is a battery powered passive infrared motion detector with a built-in transmitter. This transmitter
can be used in a variety of motion detection applications. When the passive infrared sensor detects motion in
its field of view, the transmitter sends a digitally coded wireless signal to its companion receiver. To reduce false
alarms caused by pets inside the protected area, the DXS-55AF features pet immunity with a selectable large or
small pet setting.
The transmitter is pre-coded at the factory to unique codes, so no field coding is required. The DXS-55AF can send
four different signals: alarm, low battery, status, and tamper. Receivers must be programmed to the transmitter’s
code before system testing and operation. Refer to the receiver’s instructions for details on programming.
In a typical installation, the motion detector is mounted indoors in a corner or on a wall 7-1/2 feet high. Two
mounting brackets and an adjustable PIR bracket are included. The sensor will monitor the infrared level in its
detection pattern. If the level increases or decreases rapidly (as when a person moves through the area) the
transmitter triggers, sending an alarm signal to the receiver.
The unit is powered from a 3-Volt Type CR123A lithium battery. The battery’s life can be up to three years
depending on the area’s traffic. When the battery gets low, a low battery signal will be sent to the receiver.
Approximately every hour, the DXS-55AF will send a status transmission to the receiver. The hourly signal updates
the receiver to the transmitter’s condition. By monitoring status transmissions, the receiver can determine if a
transmitter has a low battery or has been removed from the system.
To conserve battery life, during normal operation, the detector can trigger the transmitter a maximum of once every
three minutes. Opening the case will trigger a tamper transmission.
For setup and testing, pressing the small button on the left side of the case places the unit in walk test mode for
three minutes. The installer can walk in front of the unit while viewing the red test indicator through the detector’s
lens to determine the detection area.
SUPERVISED
WIRELESS
MOTION
DETECTOR
With Pet Immunity
Installation Instructions
AlarmForce Industries Inc.
675 Garyray Drive
Toronto, ON M9L 1R2, Canada
INSTALLATION BRACKETS & OPENING CASE
DETECTION PATTERN SIDE VIEW
7.5
CORNER
MOUNTING
BRACKET
PIR
LENS
15K - 25K
PET IMMUNITY
PET SIZE JUMPER
WALK TEST
BUTTON
HIGH - LOW
SENSITIVITY
JUMPER
CASE
ACCESS
SLOT
TAMPER SWITCH
CASE
LOCKING
BUTTTON
CR123A 3-VOLT
LITHIUM BATTERY
DETECTION PATTERN TOP VIEW
50°
7.5
0°
40°
-9°
3.75
3.75
30°
20°
0 3 6 9 12 15 18 21 24 27 30 33 36 39 40
WALL MOUNTING
BRACKET
7.5
PIR LOCATION
10°
0 3 6 9 12 15 18 21 24 27 30 33 36 39 40
7.5
0°
+9°
10°
-18°
3.75
3.75
20°
30°
0 3 6 9 12 15 18 21 24 27 30 33 36 39 40
SQUEEZE TOP AND BOTTOM
OF CASE TO OPEN
ADJUSTABLE PIR
MOUNTING BRACKET
TYPICAL INSTALLATION
ALL UNITS ARE IN FEET
0° IS THE PIR FACING THE OPPOSITE WALL WITH NO TILT
-9° IS THE PIR TILTED DOWN ONE CLICK
-18° IS THE PIR TILTED DOWN TWO CLICKS
+9° IS THE PIR TILTED UP ONE CLICK
PIR INSTALLATION TIPS
DON'T POINT AT HEAT SOURCES
(HEATERS, ETC.), WINDOWS, OTHER
MOTION DETECTORS OR DOOR/WINDOW
TRANSMITTERS
PIR
MOTION
DETECTOR
FRONT
ROOM
(FOR INDOOR
USE ONLY)
BEDROOM
BATH
KITCHEN
MOUNT
DETECTOR
SO THAT
INTRUDER
WILL CROSS
BEAMS
40°
0 3 6 9 12 15 18 21 24 27 30 33 36 39 40
While the DXS-55AF PIR is a highly reliable intrusion detection device, it does not offer guaranteed protection
against burglary. Any intrusion detection device is subject to compromise or failure to warn for a variety of reasons.
The following issues should be considered during new installations or when troubleshooting:
• If the premise has pets, make sure to follow the instructions in this manual concerning installation with pets.
• This PIR has built-in protection, which keeps bugs from getting into the sensor area and causing false
alarms. This does not prevent insects from crawling across the lens of the PIR, which in turn can cause the
PIR to trigger an alarm.
• Infrared energy can be reflected off any glossy surface such as mirrors, windows, floors or counter tops with
glossy finish, and slick finished concrete. Some surfaces will reflect less than others will. For example, PIRs
can see a change in infrared energy reflected off any reflective surface even if the heat or cold source is not
within the detection pattern of the PIR.
• Windows cannot only reflect infrared energy, but they can also allow sunlight or lights from cars to pass
through to the PIR. For example, a PIR can detect a quick change in infrared energy if sun light comes
through a window (which may not be detected by the PIR) and shines on a hardwood floor (which can be
detected by the PIR). If the change in infrared energy is quick enough on the floor, the PIR can trigger an
alarm. The same applies if the PIR “covers” the window, even though the pattern of protection cannot “see”
through glass. Lights from a passing car can also pass through the window at night and directly into the lens
of the detector.
• Heating and A/C ducts are also important to take into consideration because if they blow air onto an object
within the fields of view, the temperature of that object could change quickly enough for the detector to see
a change in infrared energy. Detectors cannot see air current, only the change in temperature of a physical
object.
• The PIR senses change in temperature; however, as the ambient temperature of the protected area
approaches the temperature range of 95° to 120°F, the detection performance can decrease.
50°
0 3 6 9 12 15 18 21 24 27 30 33 36 39 42
DISTANCE FROM PIR IN FEET
PIR INSTALLATION TIPS
• Make sure the area you wish to protect does not have obstructions (curtains, screens, large pieces of
furniture, plants, etc.) that may block the pattern of coverage provided by the PIR.
• Anything that can sway or move due to air current can cause a change in infrared energy within the fields
of view. Heating and A/C ducts, drafts from doors or windows can cause this to happen. Other objects to be
aware of are curtains, blinds, balloons, loose paper, plants, hanging banners or baskets, etc.
• Make sure the PIR is mounted on a solid surface and does not allow for any vibration. Vibration will not only
cause the PIR to move a little, but this will also cause the fields of view in the room to move with respect to
the PIR. A little vibration can go a long way with the fields of view, thus the PIR may see a change in energy.
• An installation may require a PIR to be aimed at a door. The PIR may “detect” door movement before the
door contact can initiate an entry delay, causing the PIR to trigger an alarm. If the PIR has to be installed this
way, it is recommended that the alarm control panel program set the PIR as an entry delay.
• The PIR detects intrusion only within the pattern of coverage as diagrammed in this manual.
• The PIR does not provide volumetric area protection.
• The PIR creates multiple beams of protection and intrusion can only be detected in unobstructed areas
covered by those beams.
• The PIR cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass
partitions, glass doors, or windows.
• Tampering with, masking, painting, or spraying of any material on the PIR lens or any part of the optical
system can reduce the detection ability of the PIR.
• The PIR will not operate without the appropriate battery installed, or if the battery is weak or improperly
connected (i.e., reversed polarity).
• The PIR, like other electrical devices, are subject to component failure. Even though the DXS-55AF is
designed to last as long as 10 years, the electronic components in it could fail at any time.
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,DXS-55AF - FILE NAME: P983 X10 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - SIDE 2 OF 2
BATTERY INSTALLATION & PROGRAMMING
PREPARE THE RECEIVER TO
"LEARN" THE TRANSMITTTER
OBSERVE BATTERY POLARITY!!!
WHEN THE RECEIVER IS READY,
INSTALL THE CR123A 3-VOLT
LITHIUM BATTERY AS SHOWN
PIR WILL SEND A TRANSMISSION
TO THE RECEIVER AND THE
TRANSMITTER'S ID WILL
BE STORED IN THE RECEIVER
MOUNTING PIR WITHOUT INSTALLATION BRACKETS
CORNER MOUNT
REAR CASE WITH
FOUR SCREWS
PET IMMUNITY TIPS
MOUNTING PIR WITH INSTALLATION BRACKETS
To take full advantage of the DXS-55AF pet
immunity features in installations with pets, use
these following steps:
• Mount the PIR with the center of the lens 7-1/2
to 8 feet above floor level.
• Set the SENSITIVITY jumper to the LOW
position.
• Set the PET SIZE jumper to the lowest setting
for the maximum pet weight.
• Mount the PIR where pets cannot come within
six feet of the unit by climbing on furniture,
boxes, or other objects.
• Do not aim the PIR at stairs or furniture, boxes,
or other objects that can be climbed by pets.
• NOTE: The DXS-55AF will provide immunity
to false alarms for an individual animal or a
group of animals whose total weight is equal
to or less than 55 pounds when the room
temperature is above 50° F and below 90° F.
If the optional mounting bracket is used, it
should be mounted with no tilt.
CORNER MOUNTING
WITH CORNER
BRACKET
- OR WALL MOUNTING
WITH WALL
BRACKET
PET SIZE
JUMPER
USE LOWEST
SETTING FOR
MAXIMUM
PET WEIGHT
SENSITIVITY
JUMPER
WALK TESTING AND OPERATIONAL TESTING
SNAP CASE
CLOSED BEFORE
WALK TESTING
RED WALK TEST INDICATOR
WILL SHOW THROUGH PIR LENS
ALARM, LOW BATTERY, & STATUS
315 MHz
OVER ONE MILLION CODES
70 MINUTES
QUAD ELEMENT
SELECTABLE: 15 Kg (33 LBS.) OR 25 Kg (55 LBS.)
SELECTABLE: HIGH OR LOW
7.5 FT. (2.3 m)
30 FT. (9.1 m) X 50 FT. (15.2 m)
86°
3.2” x 2.5” x 1.9” (8.12 x 6.35 x 4.82 cm)
3.7 OZ. (104.9 g)
WHITE
32° TO 103° F (0° TO 39° C)
5-95% NON-CONDENSING
ONE (1) PANASONIC CR123A,
OR EQUIVALENT LITHIUM BATTERY
INCLUDED ACCESSORIES: MOUNTING BRACKETS AND SCREWS, PLASTIC
WALL ANCHORS
WARRANTY: FOR THE LIFE OF THE INSTALLATION
WHEN THE SYSTEM INDICATES THAT THE
PIR HAS A LOW BATTERY, REMOVE THE
OLD BATTERY AND DISPOSE OF IT PROPERLY
PRESS WALK TEST
BUTTON ON LEFT
SIDE OF CASE
INSTALL CR123A 3-VOLT
LITHIUM BATTERY AS SHOWN
OBSERVE
BATTERY
POLARITY!!!
UNIT WILL STAY IN
WALK TEST MODE
FOR THREE MINUTES
AFTER WALK TESTING, TEST
THE PIR WITH THE SYSTEM
CONTROL PANEL OR RECEIVER
OUTPUTS:
TRANSMITTER FREQUENCY:
UNIQUE ID CODES:
SUPERVISORY INTERVAL:
SENSOR TYPE:
PET IMMUNITY:
SENSITIVITY JUMPER:
SUGGESTED MOUNTING HEIGHT:
SENSOR RANGE:
MAXIMUM HORIZONTAL SENSING ANGLE:
DIMENSIONS:
WEIGHT (INCLUDING BATTERY & BRACKET):
COLOR:
OPERATING TEMPERATURE:
RELATIVE HUMIDITY:
BATTERY (INCLUDED, NOT INSTALLED):
BATTERY REPLACEMENT
WALK ACROSS BEAM PATTERN
WHILE OBSERVING THE
WALK TEST INDICATOR
7.5 FEET
ABOVE THE
FLOOR
SPECIFICATIONS
SECURE PIR
BRACKET WITH
SCREW AND WASHER
ALWAYS SET
TO LOW FOR
PETS
- OR WALL MOUNT
REAR CASE
WITH TWO
SCREWS
7.5 FEET
ABOVE THE
FLOOR
15K = 33 LBS.
25K = 55 LBS.
7.5 FEET
ABOVE THE
FLOOR
ATTACH REAR OF
CASE TO THE
PIR BRACKET
IMPORTANT!
WARNING!
WARNING!
BATTERY MUST NOT BE RECHARGED,
DISASSEMBLED, OR DISPOSED OF
IN A FIRE. DISPOSAL OF USED BATTERIES
MUST BE MADE IN ACCORDANCE WITH THE
WASTE RECOVERY AND RECYCLING
REGULATIONS IN YOUR AREA.
IMPROPER HANDLING OF LITHIUM
BATTERIES MAY RESULT IN HEAT
GENERATION, EXPLOSION OR FIRE,
WHICH MAY LEAD TO PERSONAL
INJURIES. REPLACE WITH ONLY
TYPE CR123A BATTERY.
REGULATORY STATEMENTS
• KEEP BATTERY AWAY FROM SMALL CHILDREN. IF BATTERY IS SWALLOWED, • The radios are required to comply with Rules and Regulations. As such, they have
PROMPTLY SEE A DOCTOR.
limited transmitter power and therefore limited range.
• Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
• A receiver cannot respond to more than one transmitted signal at a time and may
be blocked by radio signals that occur on or near their operating frequencies,
regardless of code settings.
• Infrequently used radio links should be tested regularly to protect against undetected
interference or fault.
• A general knowledge of radio and its vagaries should be gained prior to acting as
a wholesale distributor or dealer, and these facts should be communicated to the
ultimate users.
Copyright © 2011
P983 X10

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 9.4.5 (Windows)
Keywords                        : 
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2011:06:24 09:47:05-07:00
Create Date                     : 2011:06:24 09:46:33-07:00
Metadata Date                   : 2011:06:24 09:47:05-07:00
Format                          : application/pdf
Title                           : P983.indd
Creator                         : Copyright © 2011 Linear LLC
Document ID                     : uuid:abb3b06c-0228-47f9-828f-1422f9ae0a4a
Instance ID                     : uuid:a1f1481b-a5f0-441e-8d60-45f62d8a2351
Startup Profile                 : Print
Page Count                      : 2
Author                          : Copyright © 2011 Linear LLC
Warning                         : [Minor] Ignored duplicate Info dictionary

EXIF Metadata provided by EXIF.tools