Seiko Epson FBWM294V2-E01 RF module User Manual QG WM294V2 E01 r13 6 FCC

Seiko Epson Corporation RF module QG WM294V2 E01 r13 6 FCC

Users Manual_rev.pdf

Quick Installation Guide WM294V2-E01 WLAN USB interface Module 802.11b/g/n (1T1R) Version 13.5 November 20, 2017 
WM294V2-E01 – Quick Installation Guide Page 2 Product Specification Product WLAN USB interface Module (802.11b/g/n) Model WM294V2-E01 Power Supply Rating 5 Vdc / 500 mA Modulation Type BPSK, QPSK, 16QAM, 64QAM Modulation Technology IEEE 802.11b: DSSS IEEE 802.11g/n: OFDM Transfer Rate 1, 2, 5.5, 6, 11, 12, 18, 22, 24, 30, 36, 48, 54, 60, 90, 120 and up to 150 Mbps Operating Frequency 2412 MHz – 2462 MHz Number of Channel 802.11b, 802.11g, 802.11n (HT20): 11 802.11n (HT40): 7 Antenna Type Multilayer Chip Antenna Peak Gain: 0.5 dBi typ. Average Gain: -0.5 dBi typ. Operating Temperature 0°C – 50°C ambient temperature Interface Type 1 Type 2 Type 3
WM294V2-E01 – Quick Installation Guide Page 3 Installing the WLAN module driver NOTE The illustrations may look different on your operating system. To install the WLAN module driver, follow the steps below: Step 1: Close all other applications before continuing. Step 2: 1. Insert the WLAN module into the USB port of your computer. 2. When the REALTEK USB Wireless LAN Driver and Utility window appears, click Next. Step 3: Follow the on-screen instructions to install the REALTEK USB Wireless LAN driver. Step 4: When the installation is completed, select “Yes, I want to restart my computer now.”, and then click Finish.
WM294V2-E01 – Quick Installation Guide Page 4 Setting up the WLAN module driver Step 1: On your desktop, click the REALTEK USB Wireless LA.. icon. Step 2: In the Available Network tab, select the network you want to connect to. Step 3: When the Wireless Network Properties window appears, click OK.
WM294V2-E01 – Quick Installation Guide Page 5 Step 4: Check the network connection status in the General tab.
WM294V2-E01 – Quick Installation Guide Page 6  Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: z Reorient or relocate the receiving antenna. z Increase the separation between the equipment and receiver. z Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. z Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. /Canada market, only channel 1~11 can be operated. Selection of other channels is IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. A minimum distance of 20 cm must be maintained between the user and the antenna of the integrated module. Under such configuration, the FCC radiation exposure limits set forth for a population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USER’S MANUAL OF THE END PRODUCT: In the user’s manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment.
WM294V2-E01 – Quick Installation Guide Page 7 If the size of the end product is smaller than 8 cm x 10 cm, then additional FCC part 15.19 statement is required to be available in the user’s manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: BKMFBWM294V2-E01 ". If the size of the end product is larger than 8 cm x 10 cm, then the following FCC part 15.19 statement has to also be available on the label: “This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.” Industry Canada statement ThisdevicecomplieswithISED’slicence‐exemptRSSs.Operationissubjecttothefollowingtwoconditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.LeprésentappareilestconformeauxCNRd’ISEDapplicablesauxappareilsradioexemptsdelicence.L’exploitationestautoriséeauxdeuxconditionssuivantes:(1)ledispositifnedoitpasproduiredebrouillagepréjudiciable,et(2)cedispositifdoitacceptertoutbrouillagereçu,ycomprisunbrouillagesusceptibledeprovoquerunfonctionnementindésirable. Radiation Exposure Statement: ThisequipmentcomplieswithISEDradiationexposurelimitssetforthforanuncontrolledenvironment.Thisequipmentshouldbeinstalledandoperatedwithminimumdistance20cmbetweentheradiator&yourbody.Déclaration d'exposition aux radiations: Cetéquipementestconformeauxlimitesd'expositionauxrayonnementsISEDétabliespourunenvironnementnoncontrôlé.Cetéquipementdoitêtreinstalléetutiliséavecunminimumde20cmdedistanceentrelasourcederayonnementetvotrecorps.ThisdeviceisintendedonlyforOEMintegratorsunderthefollowingconditions:(Formoduledeviceuse)1)Theantennamustbeinstalledsuchthat20cmismaintainedbetweentheantennaandusers,and2)Thetransmittermodulemaynotbeco‐locatedwithanyothertransmitterorantenna.Aslongas2 conditionsabovearemet,furthertransmittertestwillnotberequired.However,theOEMintegratorisstillresponsiblefortestingtheirend‐productforanyadditionalcompliancerequirementsrequiredwiththismoduleinstalled.CetappareilestconçuuniquementpourlesintégrateursOEMdanslesconditionssuivantes:(Pourutilisation
WM294V2-E01 – Quick Installation Guide Page 8 dedispositifmodule)1)L'antennedoitêtreinstalléedetellesortequ'unedistancede20cmestrespectéeentrel'antenneetlesutilisateurs,et2)Lemoduleémetteurpeutnepasêtrecoïmplantéavecunautreémetteurouantenne.Tantqueles2 conditionsci‐dessussontremplies,desessaissupplémentairessurl'émetteurneserontpasnécessaires.Toutefois,l'intégrateurOEMesttoujoursresponsabledesessaissursonproduitfinalpourtoutesexigencesdeconformitésupplémentairesrequispourcemoduleinstallé.IMPORTANT NOTE: Intheeventthattheseconditionscannotbemet(forexamplecertainlaptopconfigurationsorco‐locationwithanothertransmitter),thentheCanadaauthorizationisnolongerconsideredvalidandtheICIDcannotbeusedonthefinalproduct.Inthesecircumstances,theOEMintegratorwillberesponsibleforre‐evaluatingtheendproduct(includingthetransmitter)andobtainingaseparateCanadaauthorization.NOTE IMPORTANTE: Danslecasoùcesconditionsnepeuventêtresatisfaites(parexemplepourcertainesconfigurationsd'ordinateurportableoudecertainesco‐localisationavecunautreémetteur),l'autorisationduCanadan'estplusconsidérécommevalideetl'IDICnepeutpasêtreutilisésurleproduitfinal.Danscescirconstances,l'intégrateurOEMserachargéderéévaluerleproduitfinal(ycomprisl'émetteur)etl'obtentiond'uneautorisationdistincteauCanada.End Product Labeling Thistransmittermoduleisauthorizedonlyforuseindevicewheretheantennamaybeinstalledsuchthat20cmmaybemaintainedbetweentheantennaandusers.Thefinalendproductmustbelabeledinavisibleareawiththefollowing:“ContainsIC:1052C‐WM294V2E01”. Plaque signalétique du produit final Cemoduleémetteurestautoriséuniquementpouruneutilisationdansundispositifoùl'antennepeutêtreinstalléedetellesortequ'unedistancede20cmpeutêtremaintenueentrel'antenneetlesutilisateurs.Leproduitfinaldoitêtreétiquetédansunendroitvisibleavecl'inscriptionsuivante:"ContientdesIC:1052C-WM294V2E01".Manual Information To the End User TheOEMintegratorhastobeawarenottoprovideinformationtotheenduserregardinghowtoinstallorremovethisRFmoduleintheuser’smanualoftheendproductwhichintegratesthismodule.Theendusermanualshallincludeallrequiredregulatoryinformation/warningasshowinthismanual.Manuel d'information à l'utilisateur final L'intégrateurOEMdoitêtreconscientdenepasfournirdesinformationsàl'utilisateurfinalquantàlafaçond'installeroudesupprimercemoduleRFdanslemanueldel'utilisateurduproduitfinalquiintègrecemodule.Lemanueldel'utilisateurfinaldoitincluretouteslesinformationsréglementairesrequisesetavertissementscommeindiqué danscemanuel. European Union regulatory notice The telecommunications functionality of this product may be used in the following EU and
WM294V2-E01 – Quick Installation Guide Page 9 EFTA countries: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Notice for use in Russia For 2.4 GHz Wireless LAN operations (802.11 b/g) of this product certain restrictions apply: This equipment may be used indoor for the entire 2400 MHz - 2483.5 MHz frequency band channels (1-13). For indoor use the maximum effective incident radiated power (EIRP) is 100 mW. BrazilANATELstatement

Navigation menu