Seiko Epson FBWM294V2-E01 RF module User Manual QG WM294V2 E01 r13 6 FCC

Download:
Mirror Download [FCC.gov]
Document ID	3872310
Application ID	Qzn4pHEX8xVpoZXqYeNZJg==
Document Description	Users Manual_rev.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	36.45kB (455658 bits)
Date Submitted	2018-06-01 00:00:00
Date Available	2018-08-21 00:00:00
Creation Date	2018-05-18 16:37:07
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2018-06-01 12:19:34
Document Title	Microsoft Word - QG- WM294V2-E01_r13.6-FCC
Document Creator	PScript5.dll Version 5.2.2
Document Author:	jacchang

Quick Installation Guide
WM294V2-E01
WLAN USB interface Module
802.11b/g/n (1T1R)
Version 13.5
November 20, 2017
WM294V2-E01 – Quick Installation Guide
Product
Model
Power Supply Rating
Modulation Type
Modulation Technology
Transfer Rate
Operating Frequency
Product Specification
WLAN USB interface Module (802.11b/g/n)
WM294V2-E01
5 Vdc / 500 mA
BPSK, QPSK, 16QAM, 64QAM
IEEE 802.11b: DSSS
IEEE 802.11g/n: OFDM
1, 2, 5.5, 6, 11, 12, 18, 22, 24, 30, 36, 48, 54, 60, 90, 120 and
up to 150 Mbps
2412 MHz – 2462 MHz
Number of Channel
802.11b, 802.11g, 802.11n (HT20): 11
802.11n (HT40): 7
Antenna Type
Multilayer Chip Antenna
Peak Gain: 0.5 dBi typ.
Average Gain: -0.5 dBi typ.
Operating Temperature
0°C – 50°C ambient temperature
Interface
Type 1
Type 2
Type 3
Page 2
WM294V2-E01 – Quick Installation Guide
Installing the WLAN module driver
NOTE
The illustrations may look different on your operating system.
To install the WLAN module driver, follow the steps below:
Step 1:
Close all other applications before
continuing.
Step 2:
1. Insert the WLAN module into the USB
port of your computer.
2. When the REALTEK USB Wireless
LAN Driver and Utility window appears,
click Next.
Step 3:
Follow the on-screen instructions to install
the REALTEK USB Wireless LAN driver.
Step 4:
When the installation is completed, select
“Yes, I want to restart my computer now.”,
and then click Finish.
Page 3
WM294V2-E01 – Quick Installation Guide
Setting up the WLAN module driver
Step 1:
On your desktop, click the REALTEK
USB Wireless LA.. icon.
Step 2:
In the Available Network tab, select the
network you want to connect to.
Step 3:
When the Wireless Network Properties
window appears, click OK.
Page 4
WM294V2-E01 – Quick Installation Guide
Step 4:
Check the network connection status in
the General tab.
Page 5
WM294V2-E01 – Quick Installation Guide
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device and its antenna(s) must not be co-located or operating in conjunction with any other
antenna or transmitter.
/Canada market, only channel 1~11 can be operated. Selection of other channels is
IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC
compliance requirement of the end product, which integrates this module.
A minimum distance of 20 cm must be maintained between the user and the antenna of the
integrated module. Under such configuration, the FCC radiation exposure limits set forth for a
population/uncontrolled environment can be satisfied.
Any changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate this equipment.
USER’S MANUAL OF THE END PRODUCT:
In the user’s manual of the end product, the end user has to be informed to keep at least 20 cm
separation with the antenna while this end product is installed and operated. The end user has to
be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment
can be satisfied. The end user has to also be informed that any changes or modifications not
expressly approved by the manufacturer could void the user's authority to operate this equipment.
Page 6
WM294V2-E01 – Quick Installation Guide
If the size of the end product is smaller than 8 cm x 10 cm, then additional FCC part 15.19
statement is required to be available in the user’s manual:
This device complies with Part 15 of FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept
any interference received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID:
BKMFBWM294V2-E01 ". If the size of the end product is larger than 8 cm x 10 cm, then the
following FCC part 15.19 statement has to also be available on the label:
“This device complies with Part 15 of FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept
any interference received, including interference that may cause undesired operation.”
Industry Canada statement
This device complies with ISED’s licence‐exempt RSSs. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage
préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de
provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator &your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de
distance entre la source de rayonnement et votre corps.
This device is intended only for OEM integrators under the following conditions: (For module device use)
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co‐located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM
integrator is still responsible for testing their end‐product for any additional compliance requirements
required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation
Page 7
WM294V2-E01 – Quick Installation Guide
de dispositif module)
1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre l'antenne et les
utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 2 conditions ci‐dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas
nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour
toutes exigences de conformité supplémentaires requis pour ce module installé.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co‐location
with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not
be used on the final product. In these circumstances, the OEM integrator will be responsible for re‐evaluating
the end product (including the transmitter) and obtaining a separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations
d'ordinateur portable ou de certaines co‐localisation avec un autre émetteur), l'autorisation du Canada n'est
plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances,
l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une
autorisation distincte au Canada.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20
cm may be maintained between the antenna and users. The final end product must be labeled in a visible
area with the following: “Contains IC: 1052C‐WM294V2E01”.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne peut être
installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et les utilisateurs. Le
produit final doit être étiqueté dans un endroit visible avec l'inscription suivante:
"Contient des IC: 1052C-WM294V2E01".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or
remove this RF module in the user’s manual of the end product which integrates this module. The end user
manual shall include all required regulatory information/warning as show in this manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon
d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce
module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et
avertissements comme indiqué dans ce manuel.
European Union regulatory notice
The telecommunications functionality of this product may be used in the following EU and
Page 8
WM294V2-E01 – Quick Installation Guide
EFTA countries:
Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Notice for use in Russia
For 2.4 GHz Wireless LAN operations (802.11 b/g) of this product certain restrictions apply:
This equipment may be used indoor for the entire 2400 MHz - 2483.5 MHz frequency band
channels (1-13). For indoor use the maximum effective incident radiated power (EIRP) is 100 mW.
Brazil ANATEL statement
Page 9

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Format                          : application/pdf
Creator                         : jacchang
Title                           : Microsoft Word - QG- WM294V2-E01_r13.6-FCC
Create Date                     : 2018:05:18 16:37:07+08:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2018:06:01 12:19:34+08:00
Metadata Date                   : 2018:06:01 12:19:34+08:00
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Document ID                     : uuid:00e9b240-6fb5-462a-bce6-f42783a20b49
Instance ID                     : uuid:7ca91349-45f6-485e-8b00-3b59fb705ce3
Page Count                      : 9
Author                          : jacchang

EXIF Metadata provided by EXIF.tools