SendTek CEV75XCES76X EoC Coax MDU Wi-Fi Voice Endpoint User Manual CEV 750 UME 20130722 FCC

SendTek Corporation EoC Coax MDU Wi-Fi Voice Endpoint CEV 750 UME 20130722 FCC

Users Manual

EoC MDU Wi-Fi Voice Endpoint User’s Guide V1.0
- 1 - FFCCCC SSTTAATTEEMMEENNTT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one or more of the following measures:--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help
- 2 - CAUTION:Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- 3 - Introduction This EoC (Ethernet over Coax) MDU Wi-Fi Voice endpoint connects the telephone, wireless and Ethernet devices to a high speed access for Internet access. This endpoint brings you the latest Ethernet compatible technology that uses the coaxial cable as the network's physical wiring thereby eliminating the need to install new wiring. It is designed to operate on the coaxial TV cable installed in building. This endpoint is to connect PCs, telephone and wireless devices to broadband access of cable operators by simply plugging into the existing coaxial F-Type connector in home. Features • Plug & Play • Using existing coaxial TV cable to provide in-building distribution network of broadband access • Shares Internet access and cable TV video • 1 port connection Support 700Mbps Ethernet over Coax (EoC) • 2 Standard 10/100BaseT Fast Ethernet ports for connecting to PC or Set-Top-Box(STB) • 1 Phone Port for VoIP Voice Service • IEEE 802.11 b/g/n Wi-Fi MIMO Interface • Configurable QoS, Tag VLAN, Bandwidth Control • DHCP Option82 and Snooping Support • Statistics and Status Information Support
- 4 - HARDWARE INSTALLATION Parts Names and Functions LED Indicators on the Rear Panel Status Port LED ON Flashing OFF DC12V PWR Power ON N/A Not powered LAN1 LAN1 Link Receive or Transmit Disconnect or Link fail LAN2 LAN2 Link Receive or Transmit Disconnect or Link fail Left Link N/A Disconnect or Link fail Phone Right Connected Call Progress No Call Wi-Fi Link Receive or Transmit Disconnect or Link fail EoC + RF Link Act Link Receive or Transmit Disconnect or Link fail
- 5 - Ports on the Rear Panel Port Name Type Functions A DC12V DC Connect to the power adapter plug.B LAN1/LAN2 RJ-45 Connect to Ethernet port on PC or Set-Top-Box for Internet Access. C Phone RJ-11 Connect to Telephone Set D RF F Connect to TV E EoC + RF F Connect to F-Connector on wall Essential Hardwares Items Included Description Purpose EoC MDU Wi-Fi Voice Endpoint Main Unit Coaxial Cable (F-Type/ RG-59U) Connects from EoC+RF port to coax F-Type connector on the wall outlet.
- 6 - CAT5 Ethernet cable Connects from LAN port to Ethernet enabled devices as PC or STB Telephone wire Connects Phone port to phone setDC12V Power adapter Connects from Power port of the main unit into a wall outlet Hardware Connections 1. Select a convenient location for the EP near the PC or Ethernet device to which it will be connected. The EP should be kept away from excessive heat. 2. Using one coaxial cable to connect the EoC+RF port to F-Type connector on the wall. Using another coaxial cable to connect the other F-type RF port to TV set (optional). 3. Connect the LAN1/LAN2 port to your Ethernet-equipped device. 4. Connect the telephone to Phone port. 5. Connect the power adapter to the DC12V port into a wall outlet.
- 7 - The figure above shows how to connect PON/ FTTx/xDSL modem, user’s TV and PC to the WiFi endpoint via in-building coaxial cable network. Now you should have connected the LAN port, EoC port and the DC12V port to the appropriate devices or lines. LED will be as: PWR ON LAN ON (WiFi) ON Phone (Left) ON EoC+RF Link/Act ON For more information on LEDs, see section entitled "LED Indicators on the Rear Panel"
- 8 - TROUBLESHOOTING Please refer to the list below to aid in troubleshooting. The PWR (green) LED is off.  Make sure the power adapter is properly plugged into a live electrical outlet. The LAN (Ethernet) LED is off.  Make sure the connection to LAN port is secure.  The Ethernet device to which you are connected should be powered on and properly configured. The EoC+RF Link/Act LED is off  Check the connection to EoC+RF port is secure.  The device to which you are connected should be powered on and properly configured.  Make sure the quality of coaxial connector and cable is good. The (WiFi) LED is off.  Power off then power on the endpoint device. Cannot connect to the Wi-Fi AP.  Make sure if the settings are correct by re-configuring the endpoint device via Master.  Note the default SSID is “WIFI-EP” and the default WPA/WPA2 pre-shared key is “endpoint” before applying (Reconfig) new settings. The Phone (Left) LED is off.
- 9 - Check the VoIP SIP registered account is correct.
- 10 - SPECIFICATIONS Standards  IEEE 802.3u 100BaseT Fast Ethernet  Ethernet over Coax (EoC) compliant  IEEE 802.11b/g/n compliant Data Rates  EoC: 320Mbps throughput / 700 Mbps Phy Rate  Ethernet: 10/100 Mbps  Wi-Fi : 300Mbps maximal Transmission Range  EoC: Up to 70dB attenuation  Ethernet: 100 meters maximum Power Consumption  12V DC, Less than 8 watt Certifications  CE, FCC Part 15 LEDs  Power  (WiFi) Link/Activity  Ethernet Link/Activity  EoC Link/Activity  Phone Link and Call Progress Connectors  Two F-Type connectors, one for connecting with Master device, and one for TV Bypass  Two RJ-45 for 10/100Mbps Ethernet  One RJ-11 for Telephone

Navigation menu