Sensitech T11012177 TEMPTALE4 RF MONITOR STORES TEMPERATURE VALUES, IDENTIFIES LOCATIONS TRAVELED THROUGH AND STORES SHIPMENT INFORMATION. ALL OF THIS INFORMATION CAN BE TRANSMITTED WIRELESSLY TO A LOCAL COMPUTER. User Manual

Sensitech, INC. TEMPTALE4 RF MONITOR STORES TEMPERATURE VALUES, IDENTIFIES LOCATIONS TRAVELED THROUGH AND STORES SHIPMENT INFORMATION. ALL OF THIS INFORMATION CAN BE TRANSMITTED WIRELESSLY TO A LOCAL COMPUTER. Users Manual

a href="https://usermanual.wiki/Sensitech" itemprop="url"> Sensitech >

Users Manual

Sensitech Inc. • 800 Cummings Center • Beverly, MA 01915 (978) 927-7033 • Fax (978) 921-2112 www.sensitech.com© 2010. All Rights Reserved.TempTale is a registered trademark and TagAlert is a trademark of Sensitech, Inc.800 Cummings Center, Beverly, MA 01915 T11012177 Rev. B.TempTale®RF MonitorInstructions For UseThe Tools That Turn Information Into PowerTempTale®Manager Software Data Management Services TempTale®4 Monitor TagAlert™Monitor Millions Depend on the Integrity of Your Product.Sensitech’s Mission is to Ensure that Integrity.For more information, contact our client services group at 800-843-8367.RF Monitoring TempTale®4 Probe Monitor FCC ID SRMT11012177This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation.Changes or modifications not expressly approved by Sensitech could avoid the user’s authority to operate the equipment.
AlarmaCuando el TempTale RF está fuera del límite bajo o alto del tiempo programado, un icon de alarma aparecerá a la derecha en la parte baja de la pantalla.Parar el TempTale RFPresione y libere (1 a 3 segundos) el botón de parar “Stop” hasta que el icon de “Stop” aparezca a la derecha en la parte superior de la pantalla.AlarmWhen the TempTale RF is exposed to a temperature outside a pre-programmed limit and time threshold, an “Alarm bell” will appear in the lower right corner of the LCD display. Stopping a TempTale RF MonitorPress and hold (1 to 3 seconds) the Stop button until the “Stop sign” icon appears in the upper right corner of the LCD display. Starting a TempTale RF Monitor• Press and release the Start button.• The “Sunshine” icon appears in the upper left corner of the display. • The TempTale RF will begin to record data after the start-up delay has passed.Iniciar el TempTale RF• Presione y libere el botón de inicio “Start”. • El icon del “Sol” aparecerá a la izquierda en la parte superior de la pantalla. • El TempTale RF grabará despúes del tiempo de demura.All TempTale®RF Monitors can be programmed with a custom Start-up delay, measurement interval and alarm settings which have been pre-determined by the customer.To mark an important event (“Date Stamp”)• TempTale RF monitors provide an option to “Date Stamp” or mark an important event at any time during the monitoring cycle that will be visible when viewing the data. The mark is displayed as an arrow when viewing the graph and shown in italics when viewing the tabular data. • To mark a graph while the monitor is recording, press and release the “Start”button.• The “arrow” icon will appear temporarily in the lower left corner and the temperature history will appear on the display. Data appears as follows:1. Average temperature of Primary (Ambient) Sensor Readings2. Highest temperature recorded at Primary Sensor3. Total time above high temperature limit of Primary Sensor4. Lowest temperature recorded at Primary Sensor5. Total time below low temperature limit of Primary Sensor6. Highest RH value recorded at Secondary (RH) Sensor7. Lowest RH value recorded at Secondary (RH) SensorStopped recordingLimits exceededMarked PointRecordingDisplayed Information Temperature dataPara marcar un evento importante (Estampa de fecha)• Los TempTale RF monitores tienen la opción de marcar un evento importante que occura durante el envio. Se puede ver esta marca cuando se baja la información. La marca aparecerá como una flecha en el grafíco y en italico en el tabular. • Para marcar el evento durante el envio, presione y libere el botón de inicio “Start”. • Una flecha aparecerá en la pantalla y la información de temperatura aparecerá en el siguente orden:1. Temperatura media de las lecturas (ambiente) primarias del sensor2. La temperatura más alta registrada en el sensor primario3. Tiempo total sobre límite de alta temperatura del sensor primario4. La temperatura más baja registrada en el sensor primario5. Tiempo total debajo del límite de la baja temperatura del sensor primario6. El valor más alto de la RH registrado en el sensor secundario (RH)7. El valor más bajo de la RH registrado en el sensor secundario (RH)Pantalla del Monitor:ParadoAlarmaMarca de eventoIniciadoInformación de temperaturaLos monitores de TempTale®RF están programado con uno tiempo de demura, intervalo y limites de temperatura y tiempo que fueron requierido por el cliente.
Download:
Mirror Download [FCC.gov]
Document ID1326551
Application IDSyiqkwYUFeJdkOfVMxKacA==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize15.16kB (189445 bits)
Date Submitted2010-08-13 00:00:00
Date Available2010-08-16 00:00:00
Creation Date2010-07-28 14:34:04
Producing SoftwareAcrobat Distiller 8.2.3 (Windows)
Document Lastmod2010-07-28 14:34:04
Document TitleMicrosoft PowerPoint - TT RF User Instructions_english_spanish_Rev_B.pptx
Document CreatorPScript5.dll Version 5.2
Document Author: Sue
FCC ID Filing: SRMT11012177

Navigation menu