Sensus Metering Systems ZIGMOD10 Inline Zigbee Module User Manual FCC Part 15
Sensus Metering Systems Inc. Inline Zigbee Module FCC Part 15
Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1348395 |
| Application ID | PsvOoUjIsEIfsZiHwV0KeA== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 41.44kB (518011 bits) |
| Date Submitted | 2010-09-23 00:00:00 |
| Date Available | 2010-09-23 00:00:00 |
| Creation Date | 2010-09-21 08:45:30 |
| Producing Software | Adobe Acrobat 8.1 |
| Document Lastmod | 2010-09-21 08:45:30 |
| Document Title | FCC Part 15 |
| Document Creator | Adobe Acrobat 8.1 Combine Files |
| Document Author: | Brooke Copeland |
Certification Exhibit FCC ID: SDBZIGMOD10 IC: 2220A-ZIGMOD10 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Report Number: 10-0020.W06.11.A Manufacturer: Sensus Metering Systems, Inc. Model: ZIGMOD10 Manual 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Inline Zigbee Module – User Manual [FCC ID: SDBZIGMOD10, IC: 2220A-ZIGMOD10] Revision 2.1, 20 September, 2010 Sensus USA This document contains proprietary information. It may not be copied, transmitted or distributed, in whole or in part, without the consent of Sensus USA REVISION SUMMARY Date Author Change Description August 14, 2009 BG Baseline September 15, 2009 JAS Corrected Label information and added label Placement September 14, 2010 JAS Corrected antenna gain stipulation from 2 to 0dBi. September 20, 2010 JAS Corrected Label Information and Front Page Sensus In-Line Zigbee Module – User Manual 1.0 Introduction This document details the installation and usage of the “Sensus In-Line Zigbee Module”. At present the module is designed to work in the Sensus iConA and iConAS electric meters although in future in may work with other electric meter designs. The module is designed to sit between the sensor board and the display board within the electric meter. When a Zigbee module is not installed a ribbon cable connects the sensor and display. In the case when the module is installed the module is connected between the sensor and display, to give the electric meter Zigbee functionality. Sensus In-Line Zigbee Module – User Manual 2.0 Installation of the module within an electric meter First remove the meter outer cover. Carefully remove the meter inner cover. Disconnect the ribbon cable from the sensor pcb. Insert the Zigbee board into the connector that the display ribbon has been disconnected from. Insert the free end of the ribbon cable into the connector on the Zigbee module as shown in Figure 1. Add the jumper (short) to position J202 on the sensor board, as shown in Figure 2. Figure 1 – Zigbee module installed in a meter Sensus In-Line Zigbee Module – User Manual Figure 2 – Jumper must be fitted Sensus In-Line Zigbee Module – User Manual 3.0 Module pin-out description Pin Ribbon Connector Number Board Edge Connector Description Description MAINS_SENSE MAINS_SENSE Pass through RELAY_TRIGGER RELAY_TRIGGER Pass through RELAY_SWITCH_SENSE RELAY_SWITCH_SENSE Pass through GROUND EXTRA_CS Ribbon is grounded. Board edge is a 5V active high interrupt line to the Zigbee module. GROUND GROUND Power (Pass through) GROUND GROUND Power (Pass through) GROUND GROUND Power (Pass through) GROUND GROUND Power (Pass through) 26V_12S 26V_12S 26V from 12S base (pass through) 10 26V_2S 26V_2S 26V from 2S base (pass through) 11 5V0 5V0 5V supply to the sensor 12 GROUND GROUND Power (Pass through) 13 7759_CF 7759_CF Sensor board 14 ZIGBEE IRQ ZIGBEE IRQ Zigbee module IRQ 15 SPI_DATA_OUT SPI_DATA_OUT Sensor SPI Data Bus Sensus In-Line Zigbee Module – User Manual 16 7759_ZX 7759_ZX Sensory Zero Crossing Indictor 17 NOT USED NOT USED 18 NOT USED NOT USED 19 SPI_CLOCK SPI_CLOCK Sensor SPI Clock 20 SPI_DATA_IN SPI_DATA_IN Sensor SPI Data Appendix A General Statements Warning: Changes or modifications to this device not expressly approved by Sensus USA could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Sensus In-Line Zigbee Module – User Manual Appendix B RF Energy Health Hazard Please pay attention to the following warnings: When servicing equipment and selecting a location for the In-Line ZigbeeModule, it is important to note that a minimum distance of 20 cm (7.9 inches) is required between personnel and ZigBee Antenna to comply with a radio-frequency exposure limit of 1.0mW/cm . Professional installation required. The radio equipment described in this guide uses radio frequency transmitters. Although the power level is low, the concentrated energy from a directional antenna may pose a health hazard. The ZigBee Module integrated antenna is rated at a maximum of 0dBi. Sensus In-Line Zigbee Module – User Manual Appendix C Industry Canada Specific Statements: The term “IC:” before the radio certification number only signifies that industry Canada technical specifications were met. This Class B apparatus meets all the requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) the device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipment. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l'interférences nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée. Sensus In-Line Zigbee Module – User Manual Appendix D Compliance Label and Placement: The ZigBee host shall display the following label to indicate use of the ZigBee module within the unit. Sensus Raleigh, NC 27615 Contains Mod No. ZIGMOD10 Contains FCC ID: SDBZIGMOD10 IC: 2220A-ZIGMOD10 This device complies with Part 15 of the FCC Rules and Industry Canada Requirements. Operation is subject to the following two conditions; (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Sensus ZigBee Label location on Host Device. 10
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Tagged PDF : No XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Modify Date : 2010:09:21 08:45:30-04:00 Create Date : 2010:09:21 08:45:30-04:00 Metadata Date : 2010:09:21 08:45:30-04:00 Creator Tool : Adobe Acrobat 8.1 Combine Files Format : application/pdf Title : FCC Part 15 Creator : Brooke Copeland Document ID : uuid:01464fa8-6fee-43eb-8721-be396bcd76cf Instance ID : uuid:bd3ebcc5-08f6-4d88-bc52-3e7df32ba11e Producer : Adobe Acrobat 8.1 Page Count : 11 Author : Brooke CopelandEXIF Metadata provided by EXIF.tools