Sercomm 0WT01 Wireless Print Server, Wireless MFP Adapter User Manual PS801H v2 Usermanual

Sercomm Corporation Wireless Print Server, Wireless MFP Adapter PS801H v2 Usermanual

Users manual

WWiirreelleessss PPrriinntt SSeerrvveerr,, WWiirreelleessss MMFFPP AAddaapptteerr PPSS880011HHvv22 UUsseerr GGuuiiddee
Table of Contents Chapter 1 Introduction 1 Features........................................................................................................................................1 Safety Instructions......................................................................................................................1 Package Contents .......................................................................................................................3 Physical Details ..........................................................................................................................3 Chapter 2 LAN Installation 6 Procedure .....................................................................................................................................6 Chapter 3 MFP Configuration 7 Overview.....................................................................................................................................7 Using the Windows Wizard .....................................................................................................7 Chapter 4 Web-Based Management 12 Overview...................................................................................................................................12 Preparation.................................................................................................................................12 Connecting to the Print Server...............................................................................................13 Configuration Screens.............................................................................................................13 Appendix A Specifications 20 General Specifications.............................................................................................................20
Page 1 Chapter 1 Introduction This chapter provides an overview of your Print Server's features. Features Congratulations on the purchase of your new Print Server. Your Print Server was designed to provide a simple and efficient network printing solution. It is packed with features, including: Ø Wireless LAN Support. Wireless stations supporting the IEEE 802.11b or IEEE 802.11g standard can interoperate with the Print Server. Both LAN and WLAN users can print to the attached printer. Ø Versatility. The Wireless Print Server supports all functions of MFP (Multi-function Printer). It features a 10/100BaseT Ethernet interface port for connection to your LAN and operating system support includes Microsoft Windows 2000, XP and Vista. Ø Easy Installation. The Print Server makes adding printers or plotters to your network simple. Ø Easy Setup. A number of utility programs are supplied to simplify setup. Ø Web-based Interface. The Web-based interface provides an easy method of configuration in TCP/IP networks regardless of your operating system. Ø Compact Size. This allows the Print Server to be used even where space is limited. Safety Instructions For your own safety, and to protect your Print Server, please observe the following safety advice. 1. Unplug this device from its power source before cleaning. Use only a slightly dampened cloth for cleaning. Do not use liquid or aerosol cleaners. 2. Avoid using this product near water. Exposure to water poses an electric-shock hazard. 3. Do not place the Print Server on an unstable surface. The device may fall causing serious damage to the device. 4. This device should only be used with the power supply type specified on the marking label. If you are not sure of type of your local power supply, consult your dealer or the local power company. 5. Do not pinch, crimp or otherwise damage the power cord. If exposed to foot traffic, ensures that the cable is properly shielded and does not pose a tripping hazard. 6. If using an extension cord, makes sure the total ampere rating of the products using the cord does not exceed the extension cord's ampere rating. 7. Do not attempt to service this device, as opening or removing casing may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel. 1
Page 2 8. The Print Server should be serviced by qualified service personnel under the following conditions: • The power cord is damaged or frayed. • Liquid has been spilled onto the product. • The product has been exposed to rain or water. • The product does not operate normally in accordance with the operating instructions. • The device has been dropped or the casing has been damaged.
Page 3 Package Contents You should find the following items packaged with your Print Server. If any items are missing, contact your dealer immediately. • The Print Server unit • Power Adapter • One CD-ROM containing all support programs and this manual • Quick Install Guide Physical Details Details of the LEDs and connections are in this Chapter. Further details are contained in Appendix A - Specifications. PS801Hv2 • 1 USB Printer Port • IEEE 802.11g/802.11b Wireless Station • 10BaseT/100BaseTx LAN connection Figure 1: PS801Hv2
Page 4 LED Indicators The Print Servers have LED indicators on the top. The Error LED is red. The Status indicator LED is green. The LED indicator modes are described in the following table. Status LED (Green) Error LED (Red) Status Description Off Off No power. On Off Normal operation - Idle. Flashing Off Normal operation - transmitting or receiving packets from the network. On On Hardware error. Flashing Flashing Firmware upgrade in progress. LED Description WLAN Off - No Wireless connection available. On - Wireless connection available. Flashing - Transmitting or receiving data through the Wireless LAN. LAN Off - No LAN connection On - LA N connection available. Flashing - Transmitting or receiving data through the LAN. Diagnostic Push Button The button is recessed; a pin or paper clip can be used to press it. This button has 2 functions: • Restore the factory default settings • Print a test page containing all current settings. To restore the factory default settings: 1. Turn the Print Server OFF. 2. Press and hold the diagnostic button. While pressing the button, switch the Print Server ON. 3. If you continue pressing the button for 10 seconds, a diagnostic page will be printed, showing the new (default) settings. To generate a Diagnostic print out 1. Ensure that both the Print Server and the attached printer are ON. 2. Press the diagnostic button, and hold it in for 2 seconds. 3. The test page, containing the current settings, will be printed. Note:
Page 5 PostScript printers are unable to print this page. If you have a PostScript printer, the test page will not be printed.
Page 6 Chapter 2 LAN Installation This chapter describes how to install the Print Server in your Local Area Network. Procedure 1. Preparation • Ensure the power is OFF. Do not connect the Print Server while power is On. • Find the Default Server Name for your Print Server. The Default Server Name is shown on a sticker on the base of the device. It consists of 8 letters and/or digits. Record this name; it may be needed during configuration. 2. Connect the Printer Use the cable supplied with your printer to connect the printer to the USB port on the Print Server unit. 3. Connect the Network Cable Connect the network cable to the 10/100BaseT LAN connector on the Print Server. • To use the LAN interface, the LAN cable needs to be inserted BEFORE powering ON. • The Wired (LAN) interface should be used for initial configuration. • In the default Wireless "Infrastructure" mode, connecting a LAN cable will disable the Wireless interface. To use both the LAN and Wireless interfaces, the Wireless mode must be changed to "Ad-hoc". 4. Power Up Plug in the power adapter cable and power up. Start-up will take only a few seconds. Use only the Power Supply unit provided with the Print Server. Using a different Power Supply may cause damage. 5. Check the LEDs • The Error LED should flash, then turn Off. When the Error LED goes off and the Status LED remains lit or flashes, the Print Server is ready. • The Error LED will remain flashing if the Print Server can't connect to the USB printer. 2
Page 7 Chapter 3 MFP Configuration This chapter provides an overview of the configuration process. Overview The Print Server is designed to support many different platforms, and the configuration required would depend upon the environment in which it is installed. • The Print Server usually requires configuration, but if there's a DHCP server on your network, then the device is just plug-and-play. A Windows-based setup Wizard is also provided on the CD-ROM to simplify this task. • PCs wishing to use the printer attached to the Print Server always require configuration. See Chapter 4- Client Configuration for details. Configuration Methods The following methods are available to perform the required Print Server configuration: • Windows-based Wizard - see below for details. • Web-based setup - see Chapter 4 for details. Advanced Configuration and Management The BiAdmin management utility is provided for advanced configuration and management. This program is installed by default when the Administrator install option is chosen. See Chapter 5 for details on using BiAdmin. Using the Windows Wizard The Windows-based Wizard is supplied on the CD-ROM, and runs on Windows 95, 98, NT4.0, ME, Windows 2000 and Windows XP. Using this Wizard is the recommended method to configure the Print Server. It can be used configure the Print Server for your Network environment, even if the Print Server does not have a valid IP address. Procedure 1. Insert the supplied CD-ROM into your drive. If the setup program does not start automatically, run SETUP.exe in the root folder. 2. On the first screen, shown below, click Setup Wizard. 3
Page 8 Figure 2: MFP Screen 3. Click OK or Skip if all the setup procedures listed on the first screen are checked. 4. Select your MFP Network Adapter, then click Next to continue. Figure 3: Adapter Screen 5. Click Next to configure the IP Address screen. • Select Obtain IP Address automatically if your LAN has a DHCP Server, otherwise select Use following IP address. • For Use following IP address, enter an unused address from the range used on your LAN. Use the same Subnet Mask and Default Gateway as PCs on your LAN. 6. Click Next to see the following screen
Page 9 Figure 4: Status Screen 7. Click Next and Exit to continue to the final screen 8. Click Finish to save the data to the MFP Network Adapter. If the desired MFP is not listed: • Check that both the MFP Network Adapter and the printer are properly connected, and powered on. • Check that the proper Printer Driver has been installed. Windows Setup 1. Insert the supplied CD-ROM into your drive. If the setup program does not start, run SETUP.exe in the root folder. 2. Click PC Install to install the utility and bus driver. Figure 5: Main Screen 3. Follow the prompts to complete the installation. 4. The MFP Network Adapter Utility will then run.
Page 10 MFP Network Adapter Utility Setup 1. The program will search for the MFP Printer Servers on the network, and the MFP Network Adapter Utility screen will be displayed. • The names of the attached printer servers will be displayed if possible. • If the MFP is occupied, the status field will display the information of the user and IP address. Otherwise the default status should be "Ready" if the MFP is available. Figure 6: MFP Icon If your MFP Network Adapter is not listed: • Check that both the MFP Network Adapter and the printer are properly connected, and powered on. • Check that the proper Printer Driver has been installed. 2. Click "Init MFP" button to configure the MFP for the first time. Normally, you only need to do the configuration once. 3. Once the MFP has been connected successfully, the button will show "Disconnect" instead of "Connect".
Page 11 Figure 7: Utility Screen 4. Configuration is now complete. Note: If MFP has been idled for 5 minutes after connected, you will see the following message Figure 8: Idle Message The MFP will be disconnected automatically if you don't respond to the message within 1minute.
Page 12 Chapter 4 Web-Based Management This chapter explains how to use your Web Browser to configure the Print Server. Overview The Print Server incorporates the HTTP server. This allows you to connect to the Print Server and configure it using your Web Browser. Most browsers should work, provided they support tables and forms. Preparation Because it supports dynamic IP Address allocation using DHCP, BOOTP, or RARP, the Print Server ships with an IP Address of 0.0.0.0. This is NOT a valid IP Address. Therefore, you must do ONE of the following: • Check your DHCP server (if you have one), and determine the IP Address allocated to the Print Server. • Use the Diagnostic Button (if fitted) to print a report which includes the current IP address. (Press the Diagnostic Button, and hold it for 2 seconds.) • Use the Setup Wizard or another Print Server utility to allocate a valid IP Address to the Print Server. 4
Page 13 Connecting to the Print Server 1. Start your Web Browser. 2. In the Address box, enter HTTP:// followed by the IP Address of the Print Server. e.g. http://192.168.0.100 3. You will then be prompted for the password. If no password has been set, just press ENTER. 4. Use the menu bar to move from one screen to another. Remember to save each screen before changing to a different screen. Configuration Screens The following configuration screens are available. TCP/IP Figure 9: TCP/IP Screen IP Address DHCP Client Select this if your LAN has a DHCP Server. The Print Server will then automatically obtain an IP address from the DHCP Server. Fixed IP Address Select this to assign a fixed IP address to the Print Server. If selected, you must enter a the Device IP Address, Subnet Mask, and Gateway. Device IP Address IP Address assigned to the Print Server. Enter an unused IP address from the address range used on your LAN. Subnet Mask Use the same values as PCs on your LAN (or on the same LAN segment, if you have a Router). Gateway Address Use the same values as PCs on your LAN (or on the same LAN segment, if you have a Router).
Page 14 Connection Delay before reconnection attempt Sets how long the Print Server should wait before retrying a TCP/IP connection which is lost. Allowable values are from 0 to 255 seconds, with 2 as the default. Number of reconnection attempts Set how many attempts at reconnection will be made. After that, the TCP/IP session will be terminated. Allowable values are from 0 to 255, with 254 as the default.
Page 15 Wireless Configuration There are 2 options on the menu for Wireless configuration - Basic and Security. Wireless - Basic The settings on this screen must match the other Wireless stations in order for communication to occur. Figure 10: Wireless Screen Configuration Region or Domain Select your region from the drop-down list. This field displays the region of operation for which the wireless interface is intended. It may not be legal to operate the router in a region other than the region shown here. If your country or region is not listed, please check with your local government agency for more information on which channels you are allowed to use, and select a region, which allows those channels. (The channel list changes according to the selected region.) Station name This is the same as the Device (Host) Name on the WAN screen. On your PC, some Wireless status screens may display this name as the Access Point in use. Network Type Select the correct value for your Wireless LAN. • Ad-hoc mode is used when there is no Wireless Access Point, and each Wireless station communicates directly with other Wireless stations. • Infrastructure mode is used when each Wireless station connects to the Wireless Access point. This also provides access to the wired LAN. SSID (ESSID) To communicate, all Wireless stations MUST use the same SSID/ESSID. The default value is blank (null). Note! The SSID is case sensitive.
Page 16 Channel No. In Infrastructure mode, this setting has not effect – the Access Point determines the Channel used. For Ad-hoc mode, select the value you wish to use on your Wireless LAN. If you experience lost connections and/or slow data transfers you may need to experiment with different channels to see which is the best. Link Info Button Click this button to open a sub screen displaying link information. Wireless Security Screen There are 3 options for Wireless security: • Disabled - no data encryption is used. • WEP - data is encrypted using the WEP standard. • WPA-PSK - data is encrypted using the WPA-PSK standard. This is a later standard than WEP, and provides much better security than WEP. Use this if possible. • WPA2-PSK - this is a further development of WPA-PSK, and offers even greater security, using the AES (Advanced Encryption Standard) method of encryption. Wireless Security - WEP If "WEP" is selected, the screen will look like the following example. Figure 11: WEP Screen Security System WEP The 802.11b standard. Data is encrypted before transmission, but the encryption system is not very strong. Authentication Select the appropriate value, as used on your Wireless LAN - "Open System" or "Shared Key."
Page 17 Key Size Select the WEP Encryption level: • 64-bit (sometimes called 40-bit) encryption • 128-bit encryption (sometimes called 104 bit encryption) This selection also allows you to choose the input type for the keys – Hex or ASCII. Keys • Use the radio buttons to select the default key. • Enter the key value(s) you wish to use. Other stations must have the same key values. • Keys can be entered in Hex or ASCII, according to your Key Size selection. Hex characters are the digits (0 ~ 9) and the letters A ~ F. Passphrase Enter some printable characters in the Passphrase field and click the "Generate Keys" button to automatically configure the WEP Key(s). For 64 bit keys, four keys fields will be generated. For 128 bit keys, only the selected WEP key will be generated. Wireless Security - WPA-PSK If "WPA-PSK" is selected, the screen will look like the following example. Figure 12: WPA-PSK Screen Security System WPA-PSK Like WEP, data is encrypted before transmission. WPA is more secure than WEP, and should be used if possible. WPA-PSK is the version of WPA, which does NOT require a Radius Server on your LAN. Passphrase Enter the Keyword key value. Data is encrypted using a key derived from the PSK. Other Wireless Stations must use the same PSK. The PSK must be from 8 to 63 characters in length. Encryption Other Wireless Stations must use the TKIP method.
Page 18 Wireless Security - WPA2-PSK If "WPA2-PSK" is selected, the screen will look like the following example. Figure 13: WPA2-PSK Screen Security System WPA2-PSK This is a further development of WPA-PSK, and offers even greater security, using the AES (Advanced Encryption Standard) method of encryption. Passphrase Enter the Keyword key value. Data is encrypted using a key derived from the PSK. Other Wireless Stations must use the same PSK. The PSK must be from 8 to 63 characters in length. Encryption Other Wireless Stations must use the AES method.
Page 19 Other Screens Server Status This screen shows server system data and the current settings for all of the other screens. It is read-only; no data can be input on this screen. Printer Status This screen displays the current status of each port. For each port, the following data is listed: • Connected Printer- the model name of the printer connected to the port, if the printer name is known. (If the printer is not bi-directional, this information is unavailable.) • Status - the current status of the printer (On-line, Off-line, Out of paper) • Printing Information - this will show either Idle or Printing.
Page 20 Appendix A Specifications General Specifications PS801Hv2 Print Server Power Consumption 5.5w max. External Power Adapter 5 V DC LEDs 4 USB 2.0 Port 1 Ethernet Connecter 10/100BaseT FCC / CE FCC, CE. Class B Environmental Specifications Operating Temperature 0 ~ 40°C Storage Temp erature -10 ~ 70°C Shipping Temperature -40 ~ 70°C Operating Humidity 10 ~ 80% Storage Humidity 5 ~ 90% Shipping Humidity 5 ~ 100% A
Page 21 71FCC STATEMENTThis product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antennaIncrease the separation between the equipment or devicesConnect the equipment to an outlet other than the receiver'sConsult a dealer or an experienced radio/TV technician for assistanceI FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimetersYou are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. between the radiator and your body.

Navigation menu