Sercomm ADSG130 Smart Gateway User Manual

Sercomm Corporation Smart Gateway

User Manual

Download: Sercomm ADSG130 Smart Gateway User Manual
Mirror Download [FCC.gov]Sercomm ADSG130 Smart Gateway User Manual
Document ID4202352
Application IDkarpiP2vlcNL2Fh51VvJXQ==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize17.28kB (215979 bits)
Date Submitted2019-03-15 00:00:00
Date Available2019-03-15 00:00:00
Creation Date2019-02-18 15:12:24
Producing SoftwareAdobe PDF Library 15.0
Document Lastmod2019-02-18 15:12:24
Document TitleUser Manual
Document CreatorAdobe InDesign CC 14.0 (Macintosh)

Smart Gateway
User Guide
ADC-SG130
ADC-SG130_Installation_15.indd 1
2/18/19 3:12 PM
ADC-SG130_Installation_15.indd 2
2/18/19 3:12 PM
Smart Gateway
The Alarm.com Smart Gateway (ADC-SG130)
provides a dedicated Wi-Fi network for Alarm.com
Wi-Fi video cameras. Featuring WPS, you no longer
need to update cameras with complicated router
passwords. Simply add to an Alarm.com account,
plug into any wall outlet, connect to the existing
router, and pair with a Wi-Fi camera for instant,
secure Wi-Fi connectivity.
ADC-SG130_Installation_15.indd 1
2/18/19 3:12 PM
❶
❷
❸
❹
Power LED
Data LED
Communication LED
Wi-Fi LED
❶
❷
❸
❹
Reset Button (Pinhole)
WPS Button
Function Button
ADC-SG130_Installation_15.indd 2
2/18/19 3:12 PM
Pre-installation checklist
•	ADC-SG130 Smart Gateway (included)
•	Ethernet cable (included)
•	12 VDC power adapter (included)
•	Router with broadband (Cable, DSL,
or Fiber Optic) Internet connection
and an open Ethernet port
•	A computer, tablet, or smartphone
with an Internet connection
•	MobileTech or the Login and Password
for the Alarm.com account to which
you will add the Smart Gateway
Power Input
Ethernet Port (RJ-45)
ADC-SG130_Installation_15.indd 3
2/18/19 3:12 PM
Add the Smart Gateway to
an Alarm.com account
1. Use an Ethernet cable to connect the
Smart Gateway to an open Ethernet
(RJ-45) port on the existing router.
2. Connect the Smart Gateway’s DC power 		
adapter and plug it in to a non-switched outlet.
NOTE: For optimal Wi-Fi performance, place the
Smart Gateway on top of a table or in another
location free from physical obstructions.
3. Add the device to the account by either
selecting the account in MobileTech or
by using a web browser and entering the
following URL: www.alarm.com/addcamera.
Type in the Smart Gateway’s MAC address
to begin. The MAC address is included
on the label on the back of the device.
ADC-SG130_Installation_15.indd 4
2/18/19 3:12 PM
Wi-Fi Protected Setup (WPS) mode
•	WPS mode is the preferred way to add
an Alarm.com Wi-Fi camera to the
Smart Gateway’s Wi-Fi network.
•	Be sure to add the Smart Gateway to an
Alarm.com account before using WPS mode
to add video cameras to the Wi-Fi network.
•	To enter WPS mode, use either the Trigger
WPS feature in MobileTech or press and hold
the WPS button for approximately 1 to 3
seconds. The Wi-Fi LED will slowly flash to
indicate that the device is in WPS mode.
ADC-SG130_Installation_15.indd 5
2/18/19 3:12 PM
LED reference guide
Power
On
Device powered on
Off
Device powered off
Flashing
Device booting
Data
On/Flashing
Device transferring/receiving data
over Ethernet.
Off
No data is being transferred over Ethernet.
Please check the Ethernet connection between
the Smart Gateway and the router.
ADC-SG130_Installation_15.indd 6
2/18/19 3:12 PM
Communication
On
Connected to Internet
Off
No local or Internet connection.		
See troubleshooting section
Flashing (slowly)
Local connection, no Internet
Flashing (5 quick blinks)
Communication test initiated
Wi-Fi
On
Active
Off
Inactive
Flashing
WPS mode
ADC-SG130_Installation_15.indd 7
2/18/19 3:12 PM
Additional States
All LEDs Flashing (escalating)
Firmware Upgrade in progress
All LEDs Flashing (simultaneously)
Reset in progress
ADC-SG130_Installation_15.indd 8
2/18/19 3:12 PM
Troubleshooting
If you are still having issues using the
Smart Gateway, please try the following
troubleshooting options:
Check your router’s connection to the Internet
If you cannot access the Internet using
your router, please contact your Internet
Service Provider to restore Internet access.
Try adding the device again.
Perform a communication test
Press the Reset button (pinhole) for 1 to
3 seconds (use a paper clip or tool if necessary).
The Communication LED will quickly flash
five times to indicate that the test was sent.
Please wait two minutes before trying to
use the device again.
Power cycle
Unplug the device from power for 10 seconds
and plug it back in. Wait for the Power and
Communication LEDs to become solid before
trying to use the device again.
ADC-SG130_Installation_15.indd 9
2/18/19 3:12 PM
Reset
Press and hold the Reset button (pinhole) for
15 to 20 seconds (use a paper clip or tool if
necessary). All LEDs will flash simultaneously
to indicate that the device will reset. Wait for
the Power and Communication LEDs to become
solid before trying to use the device again.
Questions?
Visit: www.alarm.com/supportcenter
10
ADC-SG130_Installation_15.indd 10
2/18/19 3:12 PM
Notices
FCC STATEMENT
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between
the radiator & your body.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate this equipment.
ADC-SG130_Installation_15.indd 11
11
2/18/19 3:12 PM
IC STATEMENT
This device complies with Industry Canada’s licence-exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
1) l’appareil ne doit pas produire de brouillage;
2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
12
ADC-SG130_Installation_15.indd 12
2/18/19 3:12 PM
ADC-SG130_Installation_15.indd 13
2/18/19 3:12 PM
8281 Greensboro Drive
Suite 100
Tysons, VA 22102
ADC-SG130_Installation_15.indd 14
190218
© 2019 Alarm.com. All rights reserved.
2/18/19 3:12 PM

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Language                        : en-US
XMP Toolkit                     : Adobe XMP Core 5.6-c145 79.163499, 2018/08/13-16:40:22
Create Date                     : 2019:02:18 15:12:24-05:00
Metadata Date                   : 2019:02:18 15:12:24-05:00
Modify Date                     : 2019:02:18 15:12:24-05:00
Creator Tool                    : Adobe InDesign CC 14.0 (Macintosh)
Instance ID                     : uuid:e9ec93d9-0c01-4742-b903-84f4306a10df
Original Document ID            : xmp.did:98a504cc-ef62-49fd-8f9a-7de852ea9771
Document ID                     : xmp.id:28a1543e-d577-4ef1-b9e6-3166fff2891e
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:eaf96b2b-9c4f-4c6e-9431-63cb9d169196
Derived From Document ID        : xmp.did:c7281fcd-b43b-4d8a-8c2f-58f234a63195
Derived From Original Document ID: xmp.did:98a504cc-ef62-49fd-8f9a-7de852ea9771
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 14.0 (Macintosh)
History Changed                 : /
History When                    : 2019:02:18 15:12:24-05:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 16
Creator                         : Adobe InDesign CC 14.0 (Macintosh)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: P27ADSG130

Navigation menu