Sercomm MDC835 HD Wi-Fi Mini Dome Camera User Manual ADT MDC835 0729 QIG 2 ICupdate

Download:
Mirror Download [FCC.gov]
Document ID	3113851
Application ID	v4h2PvHhce2iP/P2i6GE5Q==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	39.89kB (498574 bits)
Date Submitted	2016-08-26 00:00:00
Date Available	2016-08-26 00:00:00
Creation Date	2016-08-03 17:06:25
Producing Software	pdfFactory Pro 3.51 (Windows 7 Ultimate Chinese (Traditional))
Document Lastmod	0000-00-00 00:00:00
Document Title	ADT_MDC835_0729_QIG-2_ICupdate.doc
Document Creator	pdfFactory Pro www.pdffactory.com
Document Author:	02113

℠
ADT Pulse Interactive Solutions
MDC835
Mini Dome Camera
Installation Guide
Chapter 1 Introduction
Table Of Contents
CHAPTER 1 INTRODUCTION .............................................................................. 1
Overview........................................................................................................ 1
Physical Details.............................................................................................. 2
Package Contents .......................................................................................... 4
CHAPTER 2 BASIC SETUP.................................................................................. 5
Installation...................................................................................................... 5
CHAPTER 3 CEILING MOUNTING ....................................................................... 5
Ceiling Mounting Installation ........................................................................... 5
CHAPTER 4 ADT PULSE ENROLLMENT............................................................. 9
Wired Connection to the Gateway Using the Pulse Portal ............................... 9
Using WPS with PIN to Enroll the Camera.................................................... 12
If the Camera Continually Goes Offline ......................................................... 16
APPENDIX A SPECIFICATIONS ........................................................................ 17
MDC835 IP Camera ..................................................................................... 17
Regulatory Approvals ................................................................................... 17
Copyright  2016. All Rights Reserved.
Document Version: 1.0
All trademarks and trade names are the properties of their respective owners.
1
Chapter 1
Introduction
This Chapter provides details of the IP Camera
features, components and capabilities.
Overview
This wireless 802.11n weather-resistant IP Camera, which comes with the IP66
rated housing, has a F1.8 large aperture Lens, SONY high sensitivity imaging
sensor and high power IR LED illumination, enabling it to display high quality
colorful image in low light condition and cover the distance up to 20 meters at night.
This device is also an all-in-one camera that has automatic day-night switching,
built-in heater and Mechanical Pan/Tilt/Rotate orientation adjustment.
The camera is intended for use in ADT Pulse.
Features
•
Lens Support. The IP Camera has the built-in F1.8 Lens with SONY Exmor
high sensitivity 3.75 µm pixel image sensor.
•
Dual Video Support. The IP Camera supports H.264 and MJEPG video
compression.
•
IR LEDs Support. The built-in two infrared LEDs can provide illumination
for up to 20 meters.
•
Built-in Heater. The built-in Heater ensures that the camera will continue
to operate even in extremely cold outdoor climates. The heater turns on when
the temperature falls below 26.6°F (-3°C).
Wireless Features
Chapter 1 Introduction
•
Supports 802.11n Wireless Standard. The 802.11n standard
provides for backward compatibility with the 802.11b/g wireless network.
•
Supports WPS. Wi-Fi Protected Setup (WPS) can simplify the process of
connecting the IP Camera to the wireless network by pin code mode via ADT
pulse.
•
Wired and Wireless Support. The IP Camera can be connected to the
Pulse network wirelessly. It can also be hardwired to the network.
Chapter 1 Introduction
Physical Details
Front/Rear Panel
Figure 1: Front/Rear Panel
IR LEDs
They are used to provide illumination for night time. Please
ensure that the two IR LEDs can be revealed in the
transparent Dome.
Light Sensor
This is a hardware sensor to detect lux. Please ensure that
the light sensor can be revealed in the transparent Dome.
Lens
No physical adjustment is required for the lens. Please
ensure that the lens cover remains clean.
LAN port
Use a standard Ethernet cable (not included) to connect
the LAN port of the supplied cable and the Pulse Gateway
or TS Base panel.
Note:
Plugging in the Ethernet cable will disable the wireless
interface. Only one interface can be active at any time.
The Ethernet cable should only be connected or
disconnected when the camera is powered OFF.
Attaching or detaching the Ethernet cable while the
camera is powered on does NOT switch the interface
between wired and wireless.
Chapter 1 Introduction
Power Interface
Connect the two wires of the supplied cable to the terminal
adapter. Do not use the other terminal adapters; doing so
may damage the camera.
Power Indicator
On (Green) - Power on.
(Green, Amber,
Off – No power.
Blue)
Blinking (Green) - The LED will blink during start up or
wireless connection is under association.
On (Blue) - Network connection is available (wired or
wireless).
On (Amber) - If the LED is on for 5 seconds and then turns
off, the WPS function has failed; or the heater is active.
Blinking (Amber) – The WPS function is active.
Note: If the data is being transmitted via WiFi/LAN, The
color of the LED is blue in the mean time.
Reset/WPS/Image Flip Button
Figure 2: WPS/Reset/Image Flip Button
Chapter 1 Introduction
WPS/Reset/
The button serves three functions on the camera.
Image Flip Button
WPS Pin Code Mode. When pressed and held for 5
seconds during the Pulse enrollment process, the
camera creates an encryption-secured wireless
connection.
Reset. When pressed and held over 15 seconds, the
camera reboots and the settings are restored to default
values.
Image Rotation. When the camera connected to ADT
Pulse, the image will turn 180° if you fast-click this
button twice.
Chapter 1 Introduction
Package Contents
The following items are included:
1.
IP Camera with pigtail (DC-IN and RJ45)
2.
Terminal Adapter
3.
Wall Mount Screw Package
4.
L Tool (T10)
5.
Spice Connector
2
Chapter 2
Basic Setup
This Chapter provides details of installing and configuring the IP
Camera.
Installation
Figure 3: Wired Network Connection
1. Make the Connection
Using a Wired Connection
If you are using a wired connection to the MDC835, connect
a standard Ethernet cable (not included) to the LAN port
of the supplied cable of the camera and the Pulse Gateway
or Total Security (TS) Base panel.
Using a Wireless Connection
The wireless (WPS) connection between the camera and the
Pulse Gateway or Total Security (TS) Base panel is
performed during the Pulse enrollment. See the following
section for more details.
Chapter 2 Basic Setup
NOTE: The Wireless and LAN interfaces cannot be used
simultaneously. Making a wired LAN connection disables the
NOTE
wireless interface.
2. Power Up
a. Run the AC Wire to the spice connector.
b. Screw the red wire onto the positive(+) terminal of the
terminal adapter.
c.
Screw the black wire onto the negative(-) terminal
of the terminal adapter.
d. Plug the terminal adapter into a power outlet.
CAUTION: Only use the terminal adapter provided. Using a
different adapter may cause hardware damage.
3. Check the LED
The Power LED will turn on briefly, and then start blinking.
It will blink during startup, which will take 60 to 90
seconds. After startup is completed, the Power LED should
remain ON.
4. Enroll the Camera in ADT Pulse
This process is described in the later chapter.
After the enrollment, please check the image orientation.
You may rotate the image 180 degrees by fast-clicking the
WPS/Reset/Image Flip button twice.
5. Mount the Camera
Place the camera in a desired location near a power source.
For mounting on the ceiling with the mounting plate, see
Chapter 4 for more details.
Mounting Suggestion
To get the best video quality for targets at night, make sure
that the camera’s field of view does not include a foreground
object, such as side wall or roof. Once installing on a
ceiling, angle the camera so that a minimal portion of the
wall is visible.
3
Chapter 3
Ceiling Mounting
This Chapter provides details for final ceiling
mounting of the IP Camera
Ceiling Mounting Installation
NOTE
NOTE: Ensure that the camera is configured and
enrolled in ADT Pulse before permanently
mounting it.
1. Locate an unused indoor outlet to plug into the terminal
adapter. The outlet should be located as close as possible
to the location where the camera will be permanently
mounted.
CAUTION: Do not plug in the terminal adapter until all the
connections are completed and the camera is fully mounted.
2. Identify the location where you would like to mount the
camera. And then drill three holes on the ceiling based on
the mounting template (last page).
3. Remove the sponge from the camera. And then use the L tool
to remove the three screws and the bubble from the camera.
Chapter 3 Ceiling Mounting
Figure 4: Removing the bubble from the Camera
4. If using the anchors, insert them into the mounting holes.
5. Align the three mounting holes of the camera stand with the
three holes and mount the camera stand on the ceiling using
the provided screws.
Figure 5: Ceiling Installation
NOTE: It is recommended to route the cable
through the side opening of the mounting base.
NOTE
6. The camera offers 3-axis adjustments:
Loosen the tilt adjust screw to adjust the tile angle
(0°~70°).
Adjust the pan angle (0°~330°) by holding the black liner.
Use the lens to rotate (0°~350°) the camera.
Figure 6: Angle Adjustment
Chapter 3 Ceiling Mounting
CAUTION: Do not entwine the antenna while
connecting the LVDS cable.
Figure 7: LVDS Cable
7. Attach the bubble to the camera and tighten it using the
three screws.
NOTE: You can use the marks for alignment while
attaching the bubble to the camera.
NOTE
Figure 8: Attaching the Camera
Chapter 3 Ceiling Mounting
CAUTION: Make sure to tighten up the three screws in order to
prevent water from the camera.
CAUTION: Be careful not to let the bubble cover the light
sensor and damage the LVDS cable while attaching the bubble
to the camera.
8. Connect the power cable to the terminal adapter.
Screw the red wire onto the positive(+) terminal of the
terminal adapter.
Screw the black wire onto the negative(-) terminal of the
terminal adapter.
9. Plug the terminal adapter into a power outlet.
10. Make sure the IP Camera is firmly fixed on the ceiling.
11. Verify that the camera is active on the wireless network
and is recognized by Pulse.
NOTE: It is recommended to let a qualified
technician install the device.
NOTE
4
Chapter 4
ADT Pulse Enrollment
This section provides instructions for wirelessly
enrolling the MDC835 Camera into the ADT Pulse
network. This process uses the Wi-Fi Protected Setup
(WPS) with PIN method to wirelessly enroll the
Camera to the gateway via the ADT Pulse Portal or TS
Installer App.
Wired Connection to the Gateway Using the Pulse Portal
1.
2.
3.
4.
Set up the Camera, as described in the previous chapter.
Open a web browser and in the address bar, enter:
https://Portal.ADTPulse.com.
Type your Username and Password, and then click the Sign
In button.
Click the System tab, and then click the Manage Devices
button.
Chapter 4 ADT Pulse Enrollment
5.
In the Manage Devices Assistant, click Cameras.
6.
Click the picture of the MDC835 or select it from the
drop-down list, and then click the Continue button.
10
Chapter 4 ADT Pulse Enrollment
7.
8.
9.
Assign the MDC835 a unique Camera Name (usually based on
the location of the camera) in the space provided, and
then type in the camera’s MAC ID.
Click the Continue button.
Ensure that the camera is connected to the device port
of the Gateway using the Ethernet cable. Click Continue.
11
Chapter 4 ADT Pulse Enrollment
10. After the Camera has connected and the button is no
longer grayed out, click Continue.
11. Click Finish. The Pulse enrollment is complete.
12. Disconnect the camera from the Gateway and remove from
power.
13. Install the camera in its final location.
Using WPS with PIN to Enroll the Camera
1.
2.
3.
4.
5.
Set up the camera, as described in the previous chapter.
Launch an Internet browser and log in to the Pulse portal
or TS installer app.
Enter the Manage Devices screen using one of these
methods:
For the Pulse portal, select the System tab and click
Manage Devices.
For the TS installer app, click the Pulse Devices link.
The Manage Devices screen displays.
In the Manage Devices screen, click Cameras.
Click the Add Using WPS button, located at the bottom of
the screen.
12
Chapter 4 ADT Pulse Enrollment
6.
7.
8.
9.
Locate the camera’s PIN number on the label on the rear
of the camera.
Enter the PIN number in the WPS PIN field.
Ensure that the camera is powered on and that the Power
LED is flashing green.
Click the Continue button to initiate the WPS process.
The following screen appears.
13
Chapter 4 ADT Pulse Enrollment
10. Press and hold the WPS/RESET/Image Flip button on the
camera for 5seconds to establish a wireless connection.
The Power LED flashes amber as the gateway attempts to
connect to the camera. The wireless connection is
successful when the Power LED turns solid green.
NOTE: You must complete the WPS connection within 2
minutes or else the process will time out. The time
remaining is displayed in the upper left portion of the
screen.
11. When the Camera Details screen appears, showing that the
camera has been enrolled, assign the camera a unique name
(usually based on the location of the camera) in the Name
field, and then click Save.
14
Chapter 4 ADT Pulse Enrollment
The Pulse enrollment is complete. The newly-added device
appears in the Cameras list.
12. At the top left of the screen, click Go Back.
13. Wait until the Power LED and Network LED are both lit
solid green/blue, and then disconnect the camera from
power.
14. Install the camera in its final location. For Wall
Mounting, refer to Chapter 4.
15
Chapter 4 ADT Pulse Enrollment
If the Camera Continually Goes Offline
If after enrolling it the camera, it continually goes offline
(Power LED blinks continually), the camera will automatically
attempt to recover the wireless connection. If the camera
cannot recover on its own, take the following measures to
re-establish the Wi-Fi connection.
1. Power cycle the camera.
2. If the previous measure fails, move the gateway closer to
the camera, if possible.
3. If the previous measure fails, press the camera’s reset
button for15 seconds, and then re-enroll the camera into
Pulse.
4. If the previous measure fails, install a Wi-Fi Range
Extender model WN3000RPH-2ADPAS.
16
Appendix A
Specifications
MDC835 IP Camera
Dimensions (DxH)
4.33” x 3.62” (110mm x 92mm)
Lens
F1.8. DFOV 75°
Video
Compression
H.264 and MJPEG
Image Resolution
16:9 720p (1280x 720), QHD (640x360),
VGA (640x480), QVGA (320x240)
Mixed Mode (720p, VGA, QVGA)
Operating
Temperature
-40°F to 122°F (-40°C to 50°C)
* If the temperature is below -40°C, the
device will start the heater to warm up
the device, then boot up.
Storage
Temperature
-40°F to 158°F (-40°C to 70°C)
Network Protocol
TCP/IP, HTTP, HTTPS, DHCP, SMTP, FTP,
UPnP, DDNS, NTP, RTP, RTCP, RTSP, SMB, DNS
Network
Interface
1 Ethernet 10/100BaseT (RJ45) LAN
connection
Wireless
Interface
IEEE 802.11n/802.11b/802.11g compatible
Button
1 WPS/Reset/Image Flip Button
LED
1 3-color LED for Power/Network/Heater
IR LEDs
Power Adapter
12V, 1.5A
Regulatory Approvals
FCC Statement
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
17
Appendix
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly
approved by the party responsible for compliance could void the user's authority to
operate this equipment. (Example - use only shielded interface cables when
connecting to computer or peripheral devices).
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20 centimeters between the radiator and your body.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Industry Canada statement:
This device complies with RSS-247 of the Industry Canada
Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
Ce dispositif est conforme à la norme RSS-247 d'Industrie
Canada applicable aux appareils radio exempts de licence. Son
fonctionnement est sujet aux deux conditions suivantes: (1)
le dispositif ne doit pas produire de brouillage
préjudiciable, et (2) ce dispositif doit accepter tout
brouillage reçu, y compris un brouillage susceptible de
provoquer un fonctionnement indésirable.
18
Appendix
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set
forth for an uncontrolled environment. This equipment should
be installed and operated with minimum distance 20cm between
the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux
rayonnements IC établies pour un environnement non contrôlé.
Cet équipement doit être installé et utilisé avec un minimum
de 20 cm de distance entre la source de rayonnement et votre
corps.
19
Appendix
Mounting Template
20

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Title                           : ADT_MDC835_0729_QIG-2_ICupdate.doc
Author                          : 02113
Creator                         : pdfFactory Pro www.pdffactory.com
Producer                        : pdfFactory Pro 3.51 (Windows 7 Ultimate Chinese (Traditional))
Create Date                     : 2016:08:03 17:06:25+08:00
Page Count                      : 28

EXIF Metadata provided by EXIF.tools