Sercomm NV842 4 Channel wireless Video Server User Manual NV842 manual
Sercomm Corporation 4 Channel wireless Video Server NV842 manual
Sercomm >
User manual
Video Server
User’s Guide
i
Table of Contents
CHAPTER 1 INTRODUCTION.............................................................................................. 1
Overview ............................................................................................................................ 1
Physical Details - Video Server......................................................................................... 3
Package Contents .............................................................................................................. 4
CHAPTER 2 BASIC SETUP ................................................................................................... 6
System Requirements........................................................................................................ 6
Installation - Video Server................................................................................................ 6
Setup using the Windows Wizard .................................................................................... 7
CHAPTER 3 VIEWING LIVE VIDEO ................................................................................ 12
Overview .......................................................................................................................... 12
Requirements ................................................................................................................... 12
Connecting to a Video Server on your LAN ................................................................. 12
Connecting to a Video Server via the Internet.............................................................. 14
Viewing Live Video ......................................................................................................... 16
CHAPTER 4 ADVANCED VIEWING SETUP ................................................................... 18
Introduction ..................................................................................................................... 18
Controlling User Access to the Video Stream ............................................................... 20
Making Video available from the Internet.................................................................... 21
Viewing Live Video via the Internet .............................................................................. 24
Motion Detection Alerts.................................................................................................. 25
CHAPTER 5 WEB-BASED MANAGEMENT .................................................................... 26
Introduction ..................................................................................................................... 26
Connecting to Video Server............................................................................................ 26
Welcome Screen............................................................................................................... 27
Administration Menu...................................................................................................... 28
System Screen .................................................................................................................. 29
Network Screen................................................................................................................ 31
Wireless Screen (Wireless Model Only) ........................................................................ 35
DDNS Screen.................................................................................................................... 38
IP Filter Screen................................................................................................................ 40
I/O Port Screen ................................................................................................................ 41
RS485 Screen ................................................................................................................... 42
Streamings........................................................................................................................ 45
Video & Audio Screen..................................................................................................... 47
Video Access Screen ........................................................................................................ 49
User Database Screen...................................................................................................... 51
Motion Detection Screen................................................................................................. 52
Audio Detection Screen................................................................................................... 53
E-Mail Screen .................................................................................................................. 54
FTP Screen....................................................................................................................... 56
HTTP Screen.................................................................................................................... 57
SD Card Screen ............................................................................................................... 58
SMB/CIFS Client Screen ................................................................................................ 60
Trigger & Recording Screen .......................................................................................... 61
Maintenance Screen ........................................................................................................ 63
Status Screen.................................................................................................................... 65
Log Screen........................................................................................................................ 67
ii
CHAPTER 6 WINDOWS VIEWING/RECORDING UTILITY........................................ 68
Overview .......................................................................................................................... 68
System Requirements...................................................................................................... 68
Installation ....................................................................................................................... 68
System Tray Icon............................................................................................................. 69
LiveView Screen .............................................................................................................. 70
Camera Setup .................................................................................................................. 71
LiveVew Program - for Streams Live Viewing............................................................. 73
View Recordings Program - for Streams Recording.................................................... 75
Setup Program - for Streams Configuration................................................................. 77
CHAPTER 7 TROUBLESHOOTING .................................................................................. 80
Overview .......................................................................................................................... 80
Problems........................................................................................................................... 80
APPENDIX A SPECIFICATIONS........................................................................................ 83
Video Server..................................................................................................................... 83
Regulatory Approvals ..................................................................................................... 83
Copyright Notice.............................................................................................................. 84
APPENDIX B NETWORK CAMERA HTTP CGI ............................................................. 85
User-level CGI commands (user level privilege)........................................................... 85
Admin-level CGI commands (administrator level privilege)..................................... 111
Appendices ..................................................................................................................... 132
P/N: 956YYF0001
Copyright © 2011. All Rights Reserved.
Document Version: 1.0
All trademarks and trade names are the properties of their respective owners.
1
&KDSWHU
&KDSWHU&KDSWHU
&KDSWHU
,QWURGXFWLRQ
,QWURGXFWLRQ,QWURGXFWLRQ
,QWURGXFWLRQ
This Chapter provides details of the Video Server's features, components and
capabilities.
Overview
The Video Server digitizes analog video signals and transmits digital images directly to your
wired LAN or the Internet. The Video Server is a device that used to turn an analog video
system into high performance IP-based solutions. The Video Server comes with the RS-485
interface, which can be used for external PTZ devices. It also supports Digital I/O (4-IN, 4-
OUT) for external sensors and alarms. Up to 10 authorized viewers from different locations
can view the H.264, MPEG-4 and M-JPEG streams simultaneously.
H.264 uses the new innovations in video compression technology to provide excellent video
quality from the low video data. Bit rate can be saved up more with nearly lossless coding
while using H.264. The intent of the H.264 project was to create a standard capable of
providing good video quality at lower bit rates than previous standards, without increasing the
complexity of design which would be impractical or expensive to implement.
A convenient and user-friendly Windows program is provided for both viewing and recording
video. If necessary, you can even view video using your Web Browser, on a variety of software
platforms.
Features
•
Triple Stream Live Video to Multiple Users.
The H.264, MPEG4 and JPEG encoders
built into the video server generate a ready-to-view video stream. Just connect to the video
server using your Web browser or the provided Windows utility to view live video.
•
Suitable for Home, Business or Public Facilities
. Whether for Home, Business or
Public Facility surveillance, the Video Server has the features you need.
•
Multi-Protocol Support.
Supporting TCP/IP networking, SMTP (E-mail), HTTP and
other Internet related protocols, the Video Server can be easily integrated into your
existing network.
•
Easy Configuration.
A Windows-based Wizard is provided for initial setup.
Subsequent administration and management can be performed using a standard web
browser. The administrator can configure and manage the Video Server via the LAN or
Internet.
•
SD Card Slot
. With the slot, you can insert the SD card to store recording files.
• Viewing/Recording Utility.
A user-friendly Windows utility is provided for viewing
live video. For periods when you are absent, or for scheduled recording, this application
also allows you to record video on your PC. Use the Playback function of the supplied
Windows utility to view the recorded files.
• 3D-Deinterlace Support.
It can
provide clearer image when movement speed of the
view is moderate. It provides high quality edge preserving deinterlacing with the 4th
generation motion adaptive 3D-Deinterlacing algorithm and performs proper processing
for fast motion and film video sources.
2
•
Motion Detection.
This feature can detect motion in the field of view. The Video Server
will compare consecutive frames to detect changes caused by the movement of large
objects. Motion detection alarm can be triggered via e-mail, FTP, instant messaging and/or
an external alarm device.
•
Flexible Scheduling.
You can limit access to the video stream to specified times using
a flexible scheduling system. The Motion Detection feature can also have its own schedule,
so it is active only when required.
•
Syslog Support.
If you have a Syslog Server, the Video Server can send its log data to
your Syslog Server.
•
Audio Support.
You can listen as well as look! Audio is encoded with the video if
desired. You can connect an external microphone to the video server.
•
IP Filter.
Use the IP Filter to block/accept access to the IP addresses.
•
User-definable HTTP/ HTTPS port number
. This allows Internet Gateways to use
"port mapping" so the Video Server and a Web Server can share the same Internet IP
address.
•
DDNS Support.
In order to view video over the Internet, users must know the Internet
IP address of the gateway used by the Video Server. But if the Gateway has a dynamic IP
address, DDNS (Dynamic DNS) is required. Since many existing Gateways do not support
DDNS, this function is incorporated into the Video Server.
•
NTP (Network-Time-Protocol) Support.
NTP allows the Video Server to calibrate its
internal clock from an Internet Time-Server. This ensures that the time stamp on Video
from the Video Server will be correct.
•
PoE Support.
(Wired Model Only)
You can use IEEE 802.3af PoE (Power over
Ethernet) to provide power to the Video Server, so only a single cable connection is
required.
Security Features
•
User Authentication.
If desired, access to live video can be restricted to known users.
Users will have to enter their username and password before being able to view the video
stream. User authentication is not required if the Multicast feature is enabled.
•
Password-Protected Configuration
. Configuration data can be password protected, so
that it only can be changed by the Video Server Administrator.
Wireless Features (Wireless Model Only)
•
Supports 802.11b, 802.11g and 802.11n Standards.
The 802.11n standard provides
for backward compatibility with the 802.11b standard, so 802.11n, 802.11b and 802.11g
Wireless stations can be used simultaneously.
•
Wired and Wireless Network Support.
The Video Server supports either wired or
wireless transmission.
•
WEP Support
. Full WEP support (64/128 Bit) on the Wireless interface is provided.
•
WPA/WPA2 Support
. The WPA Personal/WPA2 Personal standard is also supported,
allowing advanced encryption of wireless data.
•
WPS Support.
WPS (Wi-Fi Protected Setup) can simplify the process of connecting any
device to the wireless network by using the push button configuration (PBC) on the
Wireless Access Point, or entering a PIN code if there's no button.
3
Physical Details - Video Server
Front - Video Server
Figure 1: Front Panel
RESET button This button is recessed; you need a pin or paper clip to press it. It
can be activated at any time the video server is in the "ready" mode.
• Reset to manufacturer default value and reboot. When
pressed and held over 10 seconds, the settings of Video Server
will be set to their default values.
Note:
After this procedure is completed, the Power LED will blink three
times to confirm that the reset was completed successfully.
CH1~CH4 Each channel includes a video in port and an audio in port.
• Video in: It supports a single composite video source by using a
BNC connector.
• Audio in: If required, an external microphone can be attached
here. Microphones designed to be used with PCs are usually
compatible with this microphone input.
Output Channel This channel includes a video in port and an audio in port.
• Video in: Loop-through connection to the video signal from the
Video In connector. It allows direct connection to an external
monitor.
• Audio in: If required, an external microphone can be attached
here.
• Video Channel Switch: Push this button to switch the monitor
between the 4 input channels (CH1, CH2, CH3, CH4, CH1~4).
WPS Button Push the WPS button on the device and on your other wireless
device to perform WPS function that easily creates an encryption-
secured wireless connection automatically.
• WPS PBC Mode. When pressed and released (less then 3
seconds), the Network Camera will be in the WPS PBC mode
(Auto link mode).
• WPS Pin Code Mode. When pressed and held for over 3
seconds, the Network Camera will be in the WPS Pin Code
mode.
4
WPS LED
(Green)
On - Wireless security is On.
Off - Wireless security is Off.
Flashing - WPS sync is in progress.
Network LED
(Green)
On - LAN connection is detected.
Off - LAN connection is not detected
Blinking - Data is being transmitted or received via the LAN
connection.
POWER LED
(Green)
On - Power on.
Off - No power.
Blinking - The POWER LED will blink during start up. This will
take 15 to 20 seconds.
Rear - Video Server
Figure 2: Rear Panel
POWER Connect the supplied 12V power adapter here. Do not use other
power adapters; doing so may damage the video server.
ETHERNET port Use a standard LAN cable to connect your Video Server to a
10/100BaseT hub or switch.
RS485 The terminal block includes 1 RS-485 port (2 pins)
IO Ports The terminal block includes 8 GND ports, 4 input ports and 4 output
ports.
SD/SDHC Card
slot
Insert the SD card into the slot, if required.
Package Contents
The following items should be included: If any of these items are damaged or missing, please
contact your dealer immediately.
1. Video Server
2. Power adapter
3. Antennae (Wireless Model Only)
4. Installation CD-ROM
5
5. Quick Installation Guide
6. GPIO 8 pin x 2
7. RS-485 2 pin x 1
6
&KDSWHU
&KDSWHU&KDSWHU
&KDSWHU
%DVLF6HWXS
%DVLF6HWXS%DVLF6HWXS
%DVLF6HWXS
This Chapter provides details of installing and configuring the Video Server.
System Requirements
To use the wired LAN interface, a standard 10/100BaseT hub or switch and network cable is
required.
Installation - Video Server
1. Assemble the Video Server
For Wireless model, screw the supplied antennae to the mounting points on the rear.
2. Connect the LAN Cable
Connect the Video Server to a 10/100BaseT hub or switch, using a standard LAN cable.
For Wireless model, this will disable the Wireless Interface.
The Wireless and LAN interfaces cannot be used
simultaneously. Using the LAN interface is recommended for
initial configuration. After the Wireless settings are correct,
the Wireless interface can be used.
The first time you connect to the camera, you should connect
the LAN cable and configure the Network Camera with
appropriate settings. Then you can unplug the LAN cable and
power off the camera. The Network Camera will be in wireless
interface when you power on the camera again.
3. Connect the Camera
Connect the video output of the camera to the video in of the Video Server, using a
standard video cable with BNC connectors.
4. Power Up
Connect the supplied 12Vpower adapter to the Video Server and power up. Use only the
power adapter provided. Using a different one may cause hardware damage.
5. Check the LEDs
• The Power LED will turn on briefly, then start blinking. It will blink during startup, which
takes 15 to 20 seconds. After startup is completed, the Power LED should remain ON.
• The Network LED should be ON.
For more information, refer to Physical Details - Video Server in Chapter 1.
7
Setup using the Windows Wizard
Initial setup should be performed using the supplied Windows-based setup Wizard. This
program can locate the Video Server even if its IP address is invalid for your network. You can
then configure the Video Server with appropriate TCP/IP settings for your LAN.
Subsequent administration can be performed with your Web browser, as explained in Chapter
5 - Web-based Management.
Setup Procedure
1. Insert the supplied CD-ROM into your drive. If the setup program does not start
automatically, run NetworkCamera.exe in the root folder.
• You will see the Welcome screen shown below.
• Click the Setup button to start the setup Wizard.
Figure 3: Welcome Screen
2. The next screen, shown below, will list all the Video Servers on your LAN.
Figure 4: Camera List Screen
8
• Select the desired video server from the list on the left. The current settings for the
selected video server will be displayed in the table on the right.
• Click Next to continue.
3. You will be prompted to enter the Administrator Name and Administrator Password, as
shown below.
• If using the default values, enter administrator for the name, and leave the
password blank.
• Otherwise, enter the Administrator Name and Administrator Password set on the
Maintenance screen.
Figure 5: Password Dialog
4. This screen allows you to enter a suitable Description, and set the correct Time Zone,
Date, and Time. Make any desired changes, then click Next to continue.
Figure 6: Camera Settings
5. On the following IP Address Settings screen, shown below, choose Fixed IP Address,
Dynamic IP Address or PPPoE.
9
Figure 7: Fixed or Dynamic IP Selection
• Fixed IP is recommended, and can always be used.
• Dynamic IP can only be used if your LAN has a DCHP Server.
• PPPoE (PPP over Ethernet) is the most common login method, widely used with
DSL modems.
Click Next to continue.
6. If you chose Fixed IP Address, the following TCP/IP Settings screen will be displayed.
Figure 8: TCP/IP Settings
• Enter an unused IP Address from within the address range used on your LAN.
• The Subnet Mask and Default Gateway fields must match the values used by PCs on
your LAN.
• The Primary DNS address is required in order to use the E-mail alert or Dynamic
DNS features. Enter the DNS (Domain Name Server) address recommended by your
ISP.
• The Secondary DNS is optional. If provided, it will be used if the Primary DNS is
unavailable.
10
Click Next to continue.
7. If you chose PPPoE, the following PPPoE Settings screen will be displayed.
Figure 9: PPPoE Settings Screen
• Enter the User Name provided by your ISP.
• Enter the Password for the user name above.
Click Next.
8. The next screen, shown below, displays all details of the Video Server.
• Click Next if the settings are correct
• Click Back to modify any incorrect values.
Figure 10: Save Settings
9. Click OK to confirm that you want to save the new settings. If you want to cancel your
changes, click Cancel.
11
Figure 11: Confirm Screen
10. After clicking OK, you will see the screen below.
Figure 12: Final Screen
Clicking the Install Utility button will install the Viewing/Recording utility described in
Chapter 6 - Windows Viewing/Recording Utility.
11. Click Exit to end the Wizard.
Setup is now complete.
12
&KDSWHU
&KDSWHU&KDSWHU
&KDSWHU
9LHZLQJ/LYH9LGHR
9LHZLQJ/LYH9LGHR9LHZLQJ/LYH9LGHR
9LHZLQJ/LYH9LGHR
This Chapter provides basic information about viewing live video.
Overview
After finishing setup via the Windows-based Wizard, all LAN users can view live video using
Internet Explorer on Windows.
This Chapter has details of viewing live video using Internet Explorer.
But many other powerful features and options are available:
• To view multiple video servers simultaneously, or record video (either interactively or by
schedule), you should install the Windows Viewing/Recording utility. Refer to Chapter 6 -
Windows Viewing/Recording Utility for details on installing and using this program.
• The video server administrator can also adjust the Video Stream, and restrict access to the
video stream to known users by requiring viewers to supply a username and password. See
Chapter 4 - Advanced Viewing Setup for details.
• To make Live Video from the video server available via the Internet, your Internet
Gateway or Router must be configured correctly. See Making Video available from the
Internet in Chapter 4 - Advanced Viewing Setup for details.
Requirements
To view the live video stream generated by the Video Server, you need to meet the following
requirements:
• Windows XP, 32-bit Windows Vista/Windows 7.
• Internet Explorer 6 or later, Firefox 3.0 or later.
Connecting to a Video Server on your LAN
To establish a connection from your PC to the Video Server:
1. Use the Windows utility to get the IP address of the Video Server.
2. Start Internet Explorer.
3. In the Address box, enter "HTTP://" and the IP Address of the Video Server.
4. When you connect, the following screen will be displayed.
13
Figure 13: Home Screen
5. Click View Video.
6. If the Administrator has restricted access to known users, you will then be prompted for a
username and password.
Enter the name and password assigned to you by the Video Server administrator.
7. The first time you connect to the Video Server, you will be prompted to install an ActiveX
component (OCX or CAB file), as in the example below.
You must install this ActiveX component (OCX or CAB file) in order to view the
Video stream in Internet Explorer.
Click the "Yes" button to install the ActiveX component.
Figure 14: ActiveX OCX Prompt
8. Video will start playing automatically. There may be a delay of a few seconds while the
video stream is buffered.
14
Connecting to a Video Server via the Internet
You can NOT connect to a Video Server via the Internet unless the Video Server
Administrator has configured both the Video Server and the Internet
Gateway/Router used by the Video Server.
See Making Video available from the Internet in Chapter 4 - Advanced Viewing Setup for
details of the required configuration.
Also, you need a broadband Internet connection to view video effectively. Dial-up connections
are NOT supported.
To establish a connection from your PC to the Video Server via the Internet:
1. Obtain the following information from the Administrator of the video server you wish to
connect to:
• Internet IP Address or Domain Name of the video server.
• Port number for HTTP connections.
• Login (username, password) if required.
2. Start Internet Explorer.
3. In the Address box, enter the following:
HTTP://Internet_Address:port_number
Where Internet_Address is the Internet IP address or Domain Name of the video
server, and port_number is the port number used for HTTP (Web) connections to the
video server.
Examples using an IP address:
HTTP://203.70.212.52:1024
Where the Internet IP address is 203.70.212.52 and the HTTP port number is 1024.
Example using a Domain Name:
HTTP://mycamera.dyndns.tv:1024
Where the Domain name (using DDNS in this example) is mycamera.dyndns.tv and
the HTTP port number is 1024.
15
4. When you connect, the following screen will be displayed.
Figure 15: Home Screen
5. Click View Video.
6. If the Administrator has restricted access to known users, you will then be prompted for a
username and password.
Enter the name and password assigned to you by the Video Server administrator.
7. The first time you connect to the video server, you will be prompted to install an ActiveX
component (OCX or CAB file), as in the example below.
You must install this ActiveX component (OCX or CAB file) in order to view the
Video stream in Internet Explorer.
Click the "Yes" button to install the ActiveX component.
Figure 16: ActiveX OCX Prompt
8. Video will start playing automatically. There may be a delay of a few seconds while the
video stream is buffered.
16
Viewing Live Video
After installing the ActiveX component, you be able to view the live video stream in its own
window, as shown below.
Adjust focus manually by turning the front lens until the video becomes clear.
Figure 17: View Video Screen
There are a number of options available on this screen, accessed by select list, button or icon.
See the table below for details.
Note: The options can only be configured while using IE browser. Other browsers can just
view the video rather than configuration.
If after installing the OCX, the video still cannot be viewed, please install the decoders to solve
this problem. You can install it from the following screens:
• Supplied Windows-based setup Wizard
• View Video Screen (preferred)
Figure 18: Install Decorders
• Motion Detection Screen
17
General Options
These options are always available, regardless of the type of video server you are connected to.
Screen. Select the desired channel to view on the screen.
Select the desired option from the drop-down list.
ON. Click this to set the output I/O port to ON mode.
OFF. Click this to set the output I/O port to OFF mode.
/ Play/Stop. Use this icon to start/stop viewing.
Back to Original. Use this icon to make the image back to original size.
Zoom Out. A digital zoom out feature is available. To zoom out the
window, click this icon.
Zoom In. A digital zoom in feature is available. To zoom in the window,
click this icon.
Snapshot. Click this to take a single JPEG "snapshot" image of the current
video.
Speaker On/Off. Use this button to turn the PC's speaker on or off.
Audio Upload On/Off. This icon is displayed when the Speaker (Audio &
Video screen) is enabled. Use this slider to adjust the volume.
Volume. Use this slider to adjust the volume.
Full Screen Display. Click this button to see the full screen of the image.
Setup. Select the desired folder to save the file.
18
&KDSWHU
&KDSWHU&KDSWHU
&KDSWHU
$GYDQFHG9LHZLQJ6HWXS
$GYDQFHG9LHZLQJ6HWXS$GYDQFHG9LHZLQJ6HWXS
$GYDQFHG9LHZLQJ6HWXS
This Chapter provides information about the optional settings and features for
viewing video via the Video Server. This Chapter is for the video server
Administrator only.
Introduction
This chapter describes some additional settings and options for viewing live Video:
• Adjusting the video image
• Controlling user access to the live video stream
• Making video available from the Internet
• Using the Motion Detection feature
To Adjust the Video Image:
1. Connect to the Web-based interface of the Video Server. (See Chapter 5 - Web-based
Management for details.)
2. Select Administration, then Streamings. You will see a screen like the example below.
Figure 19: Streamings Screen
3. Make the required adjustments, as explained below, and save your changes.
19
Data - Streamings Screen
Default Streaming
Channel
Select the default channel for streaming from the drop-down list.
Streaming 1 Settings (MJPEG)
Video Format This displays the default format.
Resolution Select the desired video resolution format. The default resolution is
set to 704*576.
Fixed Video
Quality
Select the desired option. The default fix quality is set to Normal.
Max. Frame Rate Select the desired Maximum frame rate for the video stream.
The default value is 25.
Streaming 2/3 Settings
Video Format Select the desired format from the list.
Resolution Select the desired video resolution format.
Video Quality
Control
• Constant Bit Rate: Select the desired bit rate.
• Fixed Quality: Select the desired option.
GOV Length Enter the desired value between 1 and 150.
Max. Frame Rate Select the desired Maximum frame rate for the video stream.
The default value is 15.
User Defined URI You may enter the URI up to 32 characters long for accessing the
live video from camera through cell phone connection.
20
Controlling User Access to the Video Stream
By default, anyone can connect to the Video Server and view live Video at any time.
If desired, you can limit access to scheduled times, and also restrict access to known users.
To Control User Access to Live Video:
1. Connect to the Web-based interface of the Video Server. (See Chapter 5 - Web-based
Management for details.)
2. Select Video Access.
3. Set the desired options for Access.
Access
Select the desired option as required:
• If the User Access is enabled, users will be prompted for a username and password when
they connect to the camera for viewing video.
• When Video Access is enabled, viewing video is only available during the scheduled
periods, and unavailable at other times. If this option is selected, you need to define a
schedule; otherwise it is always disabled.
However, viewing video is still possible by logging in as the Administrator.
Figure 20: Controlling User Access
See Chapter 5 - Web-based Management for further details about using the Video Access and
User Database screens.
21
Making Video available from the Internet
If your LAN is connected to the Internet, typically by a Broadband Gateway/Router and
Broadband modem, you can make the Video Server available via the Internet. You will need to
configure your Router or Gateway to allow connections from the Internet to the video server.
Router/Gateway Setup
Your Router or Gateway must be configured to pass incoming TCP (HTTP) connections (from
Internet Viewers) to the Video Server. The Router/Gateway uses the Port Number to determine
which incoming connections are intended for the Video Server.
This feature is normally called Port Forwarding or Virtual Servers. The Port
Forwarding/Virtual Server entry tells the Router/Gateway that incoming TCP connections on
port 1024 should be passed to the Video Server. If necessary, check the user manual for your
Router/Gateway for further details.
The "Port" for the Port Forwarding / Virtual Server entry
above is the " Secondary Port" number specified on the
Network screen of the Video Server.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits
set forth for an uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 20 entimeters between the radiator and your body.
22
Video Server Setup
The Video Server configuration does NOT have be changed, unless:
• You wish to change the port number from the default value.
• You wish to use the DDNS (Dynamic DNS) feature of the Video Server.
HTTPS Port Configuration
Normally, HTTP (Web) connections use port 80. Since the Video Server uses HTTP, but port
80 is likely to be used by a Web Server, you can use a different port for the Video Server. This
port is called the Secondary Port.
The default HTTP/HTTPS Secondary Port is 1024/1025. If you prefer to use a different port
number, you can specify the port number on the Video Server's Network screen, as shown
below.
Figure 21: Network Screen
See Chapter 5 - Web-based Management for further details on using the Network screen.
Viewers need to know this port number in order to connect
and view live Video, so you must inform viewers of the
correct port number.
DDNS (Dynamic DNS)
Many internet connections use a "Dynamic IP address", where the Internet IP address is
allocated whenever the Internet connection is established.
This means that other Internet users don't know the IP address, so can't establish a connection.
DDNS is designed to solve this problem, by allowing users to connect to your LAN using a
domain name, rather than an IP address.
To use DDNS:
1. Register for the DDNS service with a supported DDNS service provider. You can then
apply for, and be allocated, a Domain Name.
2. Enter and save the correct DDNS settings on the DDNS screen of the Video Server.
3. Both Router and Video Server should use the same port number for DDNS service.
23
Figure 22: DDNS Screen
4. Operation is then automatic:
• The Video Server will automatically contact the DDNS server whenever it detects that
the Internet IP address has changed, and inform the DDNS server of the new IP
address.
• Internet users can then connect to the Video Server using the Domain Name allocated
by the DDNS service provider.
Example: HTTP://mycamera.dyndns.tv:1024
mycamera.dyndns.tv is domain host name. 1024 is the port number.
24
Viewing Live Video via the Internet
Clients (viewers) will also need a broadband connection; dial-up connections are NOT
recommended.
Viewing Live Video Using your Web Browser
If using your Web browser, you need to know the Internet IP address (or the Domain name) of
the video server's Router/Gateway, and the correct port number.
Enter the Internet address of the Router/Gateway, and its port number, in the Address (or
Location) field of your Browser.
Example - IP address:
HTTP://203.70.212.52:1024
Where the Router/Gateway's Internet IP address is 203.70.212.52 and the "Secondary
Port" number on the Video Server is 1024.
Example - Domain Name:
HTTP://mycamera.dyndns.tv:1024
Where the Router/Gateway's Domain name is mycamera.dyndns.tv and the "Secondary
Port" number on the Video Server is 1024.
Viewing Live Video with the Viewing/Recording Utility
If using the Windows Viewing/Recording Utility, the details of the Video Server must be
entered on the Cameras screen.
Figure 23: Add video server from LAN
See Chapter 6 - Window Viewing/Recording Utility for full details on using the Windows
Viewing/Recording utility.
25
Motion Detection Alerts
The Motion Detection feature can generate an Alert when motion is detected.
The Video Server will compare consecutive frames to detect changes caused by the movement
of large objects.
But the motion detector can also be triggered by:
• Sudden changes in the level of available light
• Movement of the camera itself.
Try to avoid these situations. The motion detection feature works best in locations where there
is good steady illumination, and the camera is mounted securely.
Note: The Motion Detection settings can only be configured while using IE browser.
To Use Motion Detection Alerts
Using the Web-based interface on the Video Server, select the Motion Detection screen, then
configure this screen as described below.
Figure 24: Motion Detection
1. Enable the Motion Detection feature.
2. Set the areas of the video image to be examined for movement. You can define up to 4
areas, and set the motion threshold individually for each area.
3. If using a schedule, define the desired schedule in Event Trigger screen.
4. Save your changes.
If the Motion Detection feature is enabled, but the related
options in the Event Trigger screen are not enabled, then the
only action when motion is detected is to log this event in the
system log.
26
&KDSWHU
&KDSWHU&KDSWHU
&KDSWHU
:HE
:HE:HE
:HE
EDVHG0DQDJHPHQW
EDVHG0DQDJHPHQWEDVHG0DQDJHPHQW
EDVHG0DQDJHPHQW
This Chapter provides Setup details of the Video Server’s Web-based
Interface. This Chapter is for the video server Administrator only.
Introduction
The Video Server can be configured using your Web Browser. The Video Server must have an
IP address which is compatible with your PC.
The recommended method to ensure this is to use the supplied Windows-based Wizard, as
described in Chapter 2 - Basic Setup.
Connecting to Video Server
• If using only your Web Browser, use the following procedure to establish a connection
from your PC to the Video Server:
• Once connected, you can add the Video Server to your Browser's Favorites or Bookmarks.
Connecting using your Web Browser
1. Use the Windows utility to get the IP address of the Video Server.
2. Start your WEB browser.
3. In the Address box, enter "HTTP://" and the IP Address of the Video Server.
4. You will then be prompted for a username and password.
• If using the default values, enter administrator for the name, and leave the
password blank.
• Otherwise, enter the Administrator ID and Administrator Password set on the
Maintenance screen.
27
Welcome Screen
When you connect, the following screen will be displayed.
Figure 25: Welcome Screen
The menu options available from this screen are:
• View Video - View live Video using your Web Browser. See Chapter 3 - Viewing Live
Video for details.
• Administration - Access the Administration menu.
28
Administration Menu
Clicking on Administration on the menu provides access to all the settings for the Video
Server.
The Administration menu contains the following options:
Setup
• System
• Network
• Wireless (Wireless Model Only)
• DDNS
• IP Filter
• I/O Port
• RS485
Video & Audio
• Streamings
• Video & Audio
• Video Access
• User Database
Event
• Motion Detection
• Audio Detection
• E-Mail
• FTP
• HTTP
• SD Card
• SMB/CIFS Client
• Trigger & Recording
Administration
• Maintenance
• Status
• Log
29
System Screen
After clicking Administration on the main menu, or selecting System on the Setup menu, you
will see a screen like the example below.
Figure 26: System Screen
Data - System Screen
System Settings
Device ID This displays the ID for the Video Server.
Camera Name Enter the desired name of the Video Server.
Description This field is used for entering a description, such as the location of the
Video Server.
Date & Time
Date Format Choose the desired format from the drop-down list.
Current
Date & Time
This displays the current date and time on the video server.
If it's not correct, click the Change button to modify the date/time
settings. This button will open a sub-screen where you have 2 options:
• Set the video server's date and time to match your PC.
• Select the correct date and time.
Time Zone Choose the Time Zone for your location from the drop-down list.
If your location is currently using Daylight Saving, enable the Adjust
for daylight saving checkbox.
30
Network Time
Protocol
Enable or disable the Time Server feature as required.
If Enabled, the Video Server will contact a Network Time Server at
regular intervals and update its internal timer.
NTP Server
Address
Enter the address for the desired NTP server.
Update The Schedule determines how often the Video Server contacts the NTP
Server.
Select the desired options.
LED Operation If Disabled, the LED of the Video Server will be in off state.
31
Network Screen
This screen is displayed when the Network option is clicked.
Figure 27: Network Screen
32
Data - Network Screen
Network
Internet Connection
Type
There are 3 connection types:
• Obtain Address Automatically (DHCP): If selected, the
Video Server will obtain its IP address and related information
from a DHCP Server. Only select this option if your LAN has a
DHCP Server.
• Static IP Address: If selected, you must assign the following
data to the Video Server.
• IP Address - Enter an unused IP address from the address
range used on your LAN.
• Subnet Mask - Use the same value as PCs on your LAN.
• Default Gateway - Use the same value as PCs on your
LAN.
• PPPoE (PPP over Ethernet): This is the most common login
method, widely used with DSL modems. Normally, your ISP
will have provided some software to connect and login. This
software is no longer required, and should not be used.
• Username - The user name (or account name) provided by
your ISP.
• Password - Enter the password for the login name above.
Obtain DNS server
address
automatically
If selected, the Video Server will use the DNS address or addresses
provided by the DHPC server.
This option is only available if the IP address setting is Obtain an
IP address automatically.
Use the following
DNS server address
Primary DNS server - Use the same value as PCs on your LAN.
Normally, your ISP will provide this address.
Secondary DNS server - This is optional. If entered, this DNS will
be used if the Primary DNS does not respond.
WINS Address There are 2 options:
• Obtain WINS address automatically - If selected, the Video
Server will obtain its IP address from DHCP server.
• Use the following WINS address - Enter the IP address of
your WINS server.
33
HTTP/HTTPS This sets the port number for HTTP/HTTPS connections to the
Video Server, whether for administration or viewing video.
The HTTP (HyperText Transfer Protocol) is used for the standard
of transferring files (text, graphic images and other multimedia
files) on the World Wide Web. The default HTTP port is 1024.
HTTPS (Hypertext Transfer Protocol Secure) can provide more
secure communication with the SSL/TLS protocol, which support
data encryption to HTTP clients and servers. The default HTTPS
port is 1025.
The Secondary port can be used for DDNS, other service and when
more than 2 Video Servers are in use.
If enabled, you can connect using either port 80 or the Secondary
port. You must enter the Secondary port number (between 1024 to
65535) in the field provided.
Note that when using a port number which is not 80, you must
specify the port number in the URL. For example, if the Video
Server's IP address was 192.168.1.100 and the Secondary port was
1024, you would specify the URL for the Video Server as follows:
http://192.168.1.100:1024
RTP/RTSP The RTSP (Real Time Streaming Protocol), a standard for
connected client(s) to control streaming data (MPEG-4) over the
World Wide Web. Enter the RTSP Port number (between 1024 and
65535) in the field provided. The default RTSP Port is 554.
The RTP (Real Time Transport Protocol), an Internet protocol for
transmitting real-time data such as audio and video.
Max RTP Data Packet field will let users limit the size of the file.
Enter the desired value between 400 and 1400.
Note: RTSP and RTP settings are for cell phone only.
Multicast RTP/RTSP
Enable Multicast Enable the feature as required.
Input Source Select the desired channel as the input source.
Video Address Enter the address of video.
Video Port Enter the desired value (between 1024 to 65534) in the field
provided. The number you entered must be even values.
Audio Address Enter the address of the audio.
Audio Port Enter the desired value (between 1024 to 65534) in the field
provided. The number you entered must be even values.
Time to Live Enter the desired length of time, if the packets fail to be delivered
to their destination within. The Time to Live you entered must be
in-between 1 to 255.
UPnP
Enable Discovery If enabled, the Video Server will broadcast its availability through
UPnP. UPnP compatible systems such as Windows XP will then be
able to detect the presence of the Video Server.
34
Enable Traversal If enabled, HTTP connections (from your Web Browser or the
Viewer and Recorder utility) can use secondary port instead of port
80 (the standard HTTP port) to access the video server.
Bonjour
Enable Bonjour
Service
If enabled, the Video Server can be accessed through a "Bonjour"
enabled browser, such as Microsoft Internet Explorer (with a
Bonjour plug-in) or Safari browser. You can also find other
Bonjour-enabled devices on your network.
QoS
Enable QoS Mode If enabled, the throughput level (for Video and Audio) is
guaranteed through QoS (Quality of Service).
DSCP Enter the desired value of Differentiated Services Code Point
(DSCP). The value must be between 0 and 63.
35
Wireless Screen (Wireless Model Only)
This screen is displayed when the Wireless menu option is clicked.
Figure 28: Wireless Screen
Data - Wireless Screen
Wireless Network
Site Survey Click the "Site Survey" button and select from a list of available
APs.
WSC PIN Code It displays the WSC PIN code number for the Video Server.
Network Type This determines the type of wireless communication used by the
Video Server.
• If you have an Access Point, select Infrastructure.
• Otherwise, select Ad-hoc.
SSID This must match the value used by other devices on your wireless
LAN. The Default is ANY.
Note! The SSID is case sensitive.
Domain Select your region from the drop-down list.
36
Channel No. • In Infrastructure mode, this setting is ignored. The Video
Server will use the Channel set on the Access Point.
• For Ad-hoc mode, select the Channel you wish to use on your
Video Server. Other Wireless stations should use the same
setting.
• If you experience interference (shown by lost connections
and/or slow data transfers) you may need to experiment with
different channels to see which one is the best.
Security
Security System Select the desired option, and then enter the settings for the selected
method:
• Disabled - No security is used. Anyone using the correct SSID
can connect to your network. This is default.
• WEP - The 802.11b standard. Data is encrypted before
transmission, but the encryption system is not very strong.
• WPA/WPA2 Personal - Like WEP, data is encrypted before
transmission. WPA is more secure than WEP, and should be
used if possible. WPA Personal is the version of WPA which
does NOT require a Radius Server on your LAN.
WEP
Authentication Type Normally this can be left at the default value of "Automatic." If that
fails, select the appropriate value - "Open System" or "Shared
Key." Check your wireless card's documentation to see what
method to use.
Note: In Infrastructure mode, either setting will normally work,
since most Access Points can use both methods.
WEP Encryption Select the WEP Encryption level:
• 64 Bit Keys (10 Hex chars)
• 128 Bit Keys (26 Hex chars)
• 64 Bit Keys (5 ASCII chars)
• 128 Bit Keys (13 ASCII chars)
Passphrase Enter a word or group of printable characters in the Passphrase box
and click the "Generate Keys" button to automatically configure the
WEP Key(s). If encryption strength is set to 64-bit, then each of the
four key fields will be populated with key values. If encryption
strength is set to 128-bit, then only the selected WEP key field will
be given a key value.
WEP Keys • Use the radio buttons to select the default key.
• Enter the key value you wish to use. Other stations must have
the same key values.
• Keys must be entered in Hex. Hex characters are the digits (0 ~
9) and the letters A ~ F.
• Click Clear Keys to set the Keys to be blank.
37
WPA/WPA2 Personal
Shared Key Enter the key value. Data is encrypted using a key derived from the
network key. Other Wireless Stations must use the same network
key. The PSK must be from 8 to 63 characters or 64 hex characters
in length.
38
DDNS Screen
Many Internet connections use a "Dynamic IP address", where the Internet IP address is
allocated whenever the Internet connection is established.
This means that other Internet users don't know the IP address, so can't establish a connection.
DDNS is designed to solve this problem, as follows:
• You must register for the DDNS service with a DDNS service provider. The DDNS
Service provider will allocate a Domain Name to you upon request.
• The DDNS settings on the DDNS screen above must be correct.
• The Video Server will then contact the DDNS server whenever it detects that the Internet
IP address has changed, and inform the DDNS server of the new IP address. (The Check
WAN IP Address determines how often the Video Server checks if the Internet IP address
has changed.)
This system allows other Internet users to connect to you using the Domain Name allocated by
the DDNS service provider.
This screen is displayed when the DDNS menu option is clicked.
Figure 29: DDNS Screen
Data - DDNS Screen
DDNS
DDNS
Enable/Disable
Enable or disable the DDNS function, as required.
Only enable this feature if you have registered for the DDNS
Service with a DDNS Server provider.
Service Provider Choose a service provider from the list.
39
Web Site Button Click this button to open a new window and connect to the Web
site for the selected DDNS service provider.
Domain (Host)
Name
Enter the Domain Name (Host Name) allocated to you by the
DDNS Server provider.
Account/E-Mail Enter the login name or the E-mail address for the DDNS account.
Password/Key Enter the password/key for the DDNS account.
Check WAN IP
Address
Set the schedule for checking if the Internet IP address has
changed. If the IP address has changed, the DDNS Server will be
notified.
NOTE: If the DDNS Service provided some software to perform
this IP address update or notification, you should NOT use this
software. The update is performed by the video server.
40
IP Filter Screen
This screen is displayed when the IP Filter option is clicked.
Figure 30: IP Filter Screen
Data - IP Filter Screen
IP Filter
IP Filter The IP Filter feature allows administrators to control Video Server
access by filtering IP address. Select the desired option from the
drop-down list.
Single/Range Select to perform either single IP address or a range of IP addresses
that you desired.
IP Address Enter an IP address or a range of IP addresses you would like to
allow or deny.
41
I/O Port Screen
The Video Server supports 1 input port and 1 output port. This screen is displayed when the
I/O Port menu option is clicked.
Figure 31: I/O Port Screen
Data - I/O Port Screen
Input Ports
Current State It indicates the current state of the input port. Once the configured
state is happened, it will trigger the event actions.
Low Select the desired State:
• High
• Low
• Rising
• Falling
Output Ports
Current State It indicates the current state of the output port.
Default State Select the desired option from the drop-down list.
Manual Trigger Select the option to control the output state.
Action When
Triggered
If an event is happened, it will trigger the event alerting.
42
RS485 Screen
This screen is displayed when the RS485 menu option is clicked.
Figure 32: RS485 Screen
Data - RS485 Screen
RS485
Enable RS-485 Enable the RS-485 feature to enable pan and tilt functions for the
device.
Ports Settings
Baud Rate Select the desired baud rate from the drop-down list. The default is
2400 bps.
Data Bits Select the desired data bits from the drop-down list. The default is
8.
Parity Select the desired parity from the drop-down list. The default is
None.
Stop Bits Select the desired value from the drop-down list. The default is 1.
Address Enter the desired address in the provided field.
Set Preset Position Click this button to define the preset point position. Please see the
following section for more details.
43
Patrol Sequence This feature determines how the Video Server will move when it is
set to "Rotate". You can set a number of Preset Positions; the Video
Server will go to the first position, then move through the list of
preset positions until it is finished. The Video Server will stop at
the last position in the list.
To create the Preset Sequence, select the desired Preset Position in
the left column, and click the "Add >>" button. Repeat until the
desired sequence is complete. Note that you can add the same
Preset Position more than once; this can be used to make the
camera stay longer at one position.
To delete a position from the Sequence, select the desired position
and click the "Remove" button.
Set Preset Position Screen
This screen is displayed when the Set Preset Positions button on the Pan/Tilt screen is clicked.
Figure 33: Preset Point Position Screen
Data - Preset Point Positions
Set Position Set the desired position through adjusting the control panel.
Set Home Click this button to set the home position of Pan/Tilt.
Preset List Select the desired Preset. The screen will update with the current
data for the selected Preset Position.
44
Preset Name Enter a suitable name for the Preset Position.
If no name is entered, the preset will have a number only.
Pan Speed Select the desired speed for the Pan function.
Tilt Speed Select the desired speed for the Tilt function.
45
Streamings
This screen is displayed when the Streamings menu option is clicked.
If you want to view streaming via the cell phone:
1. Cell phone should be supported by 3GPP protocol.
2. Enter 554 for RTSP port number in the Network screen.
3. Both MPEG-4 and H.264 format support cell phone option.
4. Enter the following address in the URI:
RTSP:// Router IP address / User Defined URI
5. Select 15 fps for Max Frame Rate.
Note! Due to the bandwidth limitation for the cell phone usage, please set the resolution,
quality and frame rate to lower values.
Figure 34: Streamings Screen
46
Data - Streamings Screen
Default Streaming
Source
Select the default channel for streaming from the drop-down list.
Video Input You can check or modify the related stream settings by selecting the
desired channel from the list.
Streaming Settings
Video Format Select the desired format from the list.
Resolution Select the desired video resolution format.
Fixed Video
Quality
Select the desired option. The default fix quality is set to Normal.
Video Quality
Control
• Constant Bit Rate: Select the desired bit rate. The default is set
to 1.0 Mbps.
• Fixed Quality: Select the desired option. The default fix quality
is set to Normal.
Profile This is only for H.264 format only. There are 3 options:
• Baseline Profile
• Main Profile
• High Profile
GOV Length Adjust the GOV interval in frame base. "2" means 1 I frame and 1 P
Frame. "3" means 1 I frame and 2 P Frames. Enter the desired value
between 2 and 150.
Max. Frame Rate Select the desired Maximum frame rate for the video stream.
The default value is 30.
User Defined URI You may enter the URI up to 32 characters long for accessing the
live video from camera through cell phone connection.
47
Video & Audio Screen
This screen is displayed when the Video & Audio option is clicked.
Figure 35: Video & Audio Screen
Data - Video & Audio Screen
Video Input You can check or modify the related video adjustments by selecting
the desired channel from the list.
Basic Video Adjustments
Brightness If necessary, you can adjust the brightness to obtain a better image.
For example, if the camera is facing a bright light, the image may be
too dark. In this case, you can increase the brightness.
Contrast Select the desired option for the Contrast. You can select a value
between -3 and 3.
Saturation Select the desired option for the Saturation. You can select a value
between -3 and 3.
Options
Enable Microphone Enable audio by checking this checkbox. Using Audio will increase
the bandwidth requirements slightly.
Audio Type Select the desired audio type.
Enable Time Stamp If enabled, the current time will be displayed on the Video image.
48
Enable Text
Display
Enable this setting if you want text to be displayed on the Video
image, and enter the desired text - up to 20 characters. This feature
is often used to identify each Video Server when multiple Video
Servers are installed.
Enable Line Out Enable this to use this feature.
49
Video Access Screen
This screen is displayed when the Video Access option on the Video & Audio menu is clicked.
Figure 36: Video Access Screen
Data - Video Access Screen
Enable Security
Checking
• If disabled - No login required. Users do not have to provide a
username and password when they connect to the video server
to view video.
• If enabled - Require login, users will be prompted for a
username and password when they connect to the video server
to view video. The video server administrator must use the
"User Database" menu option to create the desired users.
Enable Scheduled
Video Access
• If enabled - The video server is available during the scheduled
periods, and unavailable at other times. If this option is selected,
you need to define a schedule. If no schedule is defined, this
option is always disabled.
• If disabled - The option will remain disabled until you enable it.
Note that regardless of which setting is chosen, the Administrator
can ALWAYS access the video server and view live video.
Access Schedule
Scheduled Periods This displays all periods you have entered into the database. If you
have not entered any periods, this list will be empty.
Delete Use the Delete button to delete the selected item in the list.
50
Add New Schedule
Day Choose the desired option for the period.
Start Time Enter the start time using a 24 hr clock.
End Time Enter the end time using a 24 hr clock.
Add Click this button to add a new period.
51
User Database Screen
This screen is displayed when the User Database option on the Video & Audio menu is clicked.
Figure 37: User Database Screen
Data - User Database Screen
Existing Users
User List This displays all users you have entered into the User database. If
you have not entered any users, this list will be empty.
Edit, Delete, Delete
All
Use these buttons to manage the user database.
User Properties
User Name Enter the name for the user here.
• Spaces, punctuation, and special characters must NOT be used
in the name.
• The name is case insensitive (case is ignored), so you can not
have 2 names which differ only by case.
User Password The password for this user.
Confirm Password Re-enter the password for the user, to ensure it is correct.
Control Level Select the desired control level for the user you plan to add. (*
Operator level allows user to trigger output port manually)
Add Button Click this button to add a new user, using the data shown on screen.
Clear Button Use this button to clear the input fields, ready to add a new user.
52
Motion Detection Screen
This screen is displayed when the Motion Detection option on the Event menu is clicked.
.
Figure 38: Motion Detection Screen
Data - Motion Detection Screen
Video Input Select the desired channel to set the detection areas.
Set Detection Areas
Set Detection Areas You can set the full screen or areas of the video image to be
examined.
Note: Motion detection can be triggered by rapid changes in lighting
condition, as well as by moving objects. For this reason, it should
only be used indoors.
Indicator Current value for the Motion detection.
Threshold Adjust the threshold of detection for each area
53
Audio Detection Screen
This screen is displayed when the Audio Detection option on the Event menu is clicked.
.
Figure 39: Audio Detection Screen
Data - Audio Detection Screen
Audio Input Select the desired channel to set the audio volume.
Audio Detection
Current
Volume
It displays the current volume of the environment.
Triggered
Volume
Drag the bar to set the volume for triggering.
Triggered
When
Choose the desired situation for triggering the audio detection.
54
E-Mail Screen
This screen is displayed when the E-Mail option on the Event menu is clicked.
Figure 40: E-Mail Screen
Data - E-Mail Screen
Primary/Secondary SMTP Server
SMTP Server
Address
Enter the address of the SMTP (Simple Mail Transport Protocol)
Server to be used to send E-Mail.
Authentication Select the desired Authentication type for the SMTP Server.
SMTP Login name Enter your login name for the SMTP Server.
SMTP Password Enter your password for the SMTP Server.
POP server name Enter the name for the POP Server.
Show "From" as Enter the E-Mail address to be shown in the "From" field when the
E-mail is received.
Test the Server Click this button to test the server connection.
Secondary SMTP Check the box to upload to the Secondary SMTP if the video server
can not connect to the primary SMTP.
E-Mail Setup
E-Mail Address Enter at least one (1) E-Mail address; the 2nd and 3rd addresses are
optional. The E-mail alert will be sent to the E-mail address or
addresses specified here.
55
With Attachment Enable the checkbox if you want to attaché files to the E-mail.
Subject Enter the desired text to be shown as the "Subject" for the E-Mail
when it is received. Subject can not exceed 48 alphanumeric
characters.
56
FTP Screen
This screen is displayed when the FTP option on the Event menu is clicked.
Figure 41: FTP Screen
Data - FTP Screen
Primary/Secondary FTP
FTP Server Enter the address of the FTP Server.
Port Enter the Port of the FTP Server to be connected.
Login name Enter your login name for the FTP Server.
Password Enter your password for the FTP Server.
Enable Passive
Mode
Check the box to enable the Passive mode feature of the FTP.
File Path Name Enter the file path/name of the FTP.
Test the Server Click this button to test the server connection.
Secondary FTP Check the box to upload to the Secondary FTP if the video server
can not connect to the primary FTP.
57
HTTP Screen
This screen is displayed when the HTTP option on the Event menu is clicked.
Figure 42: HTTP Screen
Data - HTTP Screen
HTTP Notification
URL Enter the URL of your HTTP notification server.
User Name Enter the user name of your HTTP server.
Password Enter the password to match the user name above.
Proxy Server
Name
Specify the proxy server name in the provided field if the device
needs to pass through a Proxy Server to do the HTTP notification.
Proxy User Name Enter the user name for the proxy server.
Proxy Password Enter the password for the proxy server.
Proxy Port
Number
Enter the port number for the proxy server.
Method Select the desired method of form data encoding.
• Get - It should be used if and only if the form processing is
independent, which typically means a pure query form.
Generally it is advisable to do so.
• Post - If there are problems related to long URLs and non-
ASCII character repertoires, which can make it necessary to use
"POST" even for independent processing.
58
SD Card Screen
This screen is displayed when the SD Card option is clicked.
Figure 43: SD Card Screen
Data - SD Card Screen
Card Management
Card Status It shows details of the card, if any.
• Total Size
• Used Size
• Free Size
• Used (%)
Refresh Click this button to update the status of the current SD card
Format Format the SD card by clicking the Format button.
Safely Remove When you want to remove the card, click this button.
59
When disk is full Select the desired option for the behavior when the disk space limit
is reached.
• Overwrite oldest file. The Recorder will overwrite the oldest
file if the space is not enough for further recording.
• Stop recording. If the disk space limit is reached, no further
recording is done.
Continuous Recording
Continuous
Recording
Enter the desired time (minute) to set the maximum time period of a
recording.
Video Clips Click View button to see the details of the video clips.
60
SMB/CIFS Client Screen
This screen is displayed when the SMB/CIFS Client option on the Event menu is clicked.
Figure 44: SMB/CIFS Client Screen
Data - SMB/CIFS Client Screen
SMB/CIFS Client
Browse SMB/CIFS
Server
Click Browse button to select the desired SMB/CIFS server.
Server Name Enter the name of your SMB/CIFS server.
File Path Enter the file path of your SMB/CIFS server.
User Name Enter the user name for the SMB/CIFS client account.
Password Enter the password for the SMB/CIFS client account.
Test the Server Click this button to test the server connection.
61
Trigger & Recording Screen
This screen is displayed when the Event Trigger option on the Event menu is clicked.
Figure 45: Event Trigger Screen
Data - Event Trigger Screen
Event Schedule
Schedule List The Event Schedule shows all of the event types currently
configured in the Video Server, along with various information about
their configuration, as listed below:
• Name - the descriptive event name set by the user.
• Effective Time Frame - shows when the event at a set time will
be triggered.
• Trigger by - shows what kind trigger activate the event.
• Action - shows what kind of the actions will be issued when the
event been triggered
Add, Edit, Delete
Button
Use the buttons to manage the selected schedule.
New Schedule
Effective Time
Frame
Choose the desired option for the period.
Start Time Choose the desired start time using a 24 hr clock.
End Time Choose the desired end time using a 24 hr clock.
Add Button Use this button to add the new schedule.
62
Trigger Event
Enable Check to perform all of the event(s) that were configured and
scheduled.
Interval Select the desired option for the events interval. (* "0" = No Delay)
Trigger by • Input 1 - This describes the states that the input must be in for
an event to be triggered.
• Audio Detection - The sound detection can be used to trigger
events.
• Motion Detection - Movement in a motion detection window
can be used to trigger events.
Actions • E-Mail - If checked, an E-Mail (with "Attachment") will be
delivered to the SMTP server. (SMTP Server must be
configured on the E-Mail page.)
• FTP - If checked, an FTP upload will be activated to the FTP
server. (FTP servers must be configured on the FTP page.)
• Output Port - If checked, the output port state will be activated
as configured. (Output port must be configured on the I/O Port
page.)
• HTTP - If checked, a HTTP CGI command will be delivered to
the HTTP server.
• SMB/CIFS - If checked, JPEG image(s) or video files will be
uploaded to the SMB server. (SMB must first be enabled and
configured on the SMB Client page.)
Attachment Type • Streaming Channel - Select the desired type for the video file.
• Pre/Post Capture - Select the desired length. The size of the
file depends on this setting, and also the Video size and degree
of compression.
63
Maintenance Screen
This screen is displayed when the Maintenance option on the Administration menu is clicked.
.
Figure 46: Maintenance Screen
Data - Maintenance Screen
Administrator Login
Administrator
ID
Enter the name for the Administrator here.
Spaces, punctuation, and special characters must NOT be used in the
name.
Administrator
Password
Enter the password for the Administrator.
Verify Password Re-enter the password for the Administrator, to ensure it is correct.
Firmware Upgrade
Upgrade File Click the "Browse" button and browse to the location on your PC
where you stored the Firmware file. Select this file.
Start Click this button to upgrade the Firmware. When the upgrade is
finished, the Video Server will restart, and this management connection
will be unavailable during the restart.
Clear File Name This does NOT stop the Upgrade process if it has started. It only clears
the input for the "Upgrade File" field.
64
Backup & Restore
Backup
Configuration
File
Click Backup button to save the current configuration information to a
text file.
Restore
Configuration
File
Click Restore button to reinitialize the video server to load the new
updated software. Do this after loading the upgrade file.
Clear File Name This does NOT stop the Restore process if it has started. It only clears
the input for the "Restore Configuration File" field.
Buttons
Defaults Click Defaults button to reload the default settings of the video server.
Restart Click Restart button to restart the video server.
65
Status Screen
This screen is displayed when the Status option on the Administration menu is clicked.
Figure 47: Status Screen
Data - Status Screen
System
Device Name This shows the name of the Video Server.
Description This shows the description of the Video Server, such as location.
F/W version The version of the current firmware installed.
Network
MAC Address The MAC address of the Video Server.
IP Address The IP Address of the Video Server.
66
Network Mask The network mask associated with the IP address above.
Gateway The IP Address of the remote Gateway associated with the IP Address
above.
WINS Address The IP Address of the WINS server.
Wireless (Wireless Model Only)
WSC PIN Dode It displays the current WSC PIN code.
Network Type This shows the Network Type currently in use (Ad-hoc or
Infrastructure).
SSID This displays the wireless SSID.
Channel This shows the wireless channel currently used.
Security The current security setting for Wireless connections.
Signal Strength This shows the strength of the signal.
Channel (1~4)
Video Format It displays the current format of video.
Resolution The image size of the video stream.
Video Quality This displays the image quality of the video stream.
Frame Rate This displays the frame rate of the video stream.
Buttons
Refresh Update the log and any other data on screen.
67
Log Screen
This screen displays a log of system activity.
Figure 48: Log Screen
Data - Log Screen
Log
System Log This is a log of system activity.
Refresh Button Click this to update the data shown on screen.
Clear Log Click this button to restart the log.
Enable Syslog
Service
Check the box to enable the System Log Server feature.
Syslog Server
Address
Enter the address of the Syslog Server.
68
&KDSWHU
&KDSWHU&KDSWHU
&KDSWHU
:LQGRZV
:LQGRZV:LQGRZV
:LQGRZV
9LHZLQJ5HFRUGLQJ8WLOLW\
9LHZLQJ5HFRUGLQJ8WLOLW\9LHZLQJ5HFRUGLQJ8WLOLW\
9LHZLQJ5HFRUGLQJ8WLOLW\
This Chapter describes how to view and record the live video stream
generated by the Video Server, using the supplied Windows utility.
Overview
The Utilities package includes following three functions:
• LiveView - to view/listen the live streams.
• View Recordings - to record the live streams.
• Setup - to configure the Utilities such as adding device, making recording schedules and
setting required parameters, etc..
The Utilities must be installed in the Windows before they can be configured.
System Requirements
In order to use the utility, you need to meet the following requirements:
• Windows XP SP3, 32-bit Windows Vista/Windows 7.
• Microsoft .NET Framework 3.5 Service Pack 1 (it should be installed on Windows
XP/VISTA via "Windows Update").
• Internet Explorer 6 or later, Firefox 3.0 or later
• 2GB RAM
• Individual Graphic Card
Installation
1. Insert the supplied CD-ROM into your drive. If the setup program does not start
automatically, run NetworkCamera.exe in the root folder. You will see the Welcome
screen shown below.
69
Figure 49: Welcome Screen
2. Click the Install Utility button to start the installation of the Utilities package.
3. Follow the prompts to complete the installation.
4. After the installation, double click the Monitor icon on the desktop or click Monitor menu
item in the Windows main program menu to launch the Utilities.
System Tray Icon
When started, the program will create an icon in the Windows system tray on the taskbar, as
shown below.
Figure 50: System Tray Icon
You can right click the icon and it will provides a menu which allows you to launch utility
program, view the utility details or even exit the utility package.
70
LiveView Screen
When Utility launched, the Camera Utility screen like the example below will be displayed.
Figure 51: Main Screen
If no devices have been defined and added to the Utilities, no video will be displayed. Utilities
should be configured first to view the streams. See the following section for information on
defining a device. Note that each device is given a number (Channel Number).
71
Camera Setup
To define a device and associate it with a Channel Number:
1. Click the Setup icon on the main screen. You will see a screen like the example below.
Figure 52: Cameras Screen
2. Add desired Video Server to the Camera List:
• To associate a device automatically with the current Channel:
• The Utilities will search and display all available devices found on your LAN in
the Add Camera list automatically. The Add Camera list can be updated by
clicking the Refresh button.
• The Camera Details panel, on the right, displays the data for the selected device.
• Check that the Camera Details shown on the right is correct. Enter associated
User Name and Password.
Note: The Port Number, User Name, Password and Stream Type can only be
modified in the WEB UI instead of Camera Setup screen.
• Click the Test Camera button to check that a connection and login can be
performed successfully.
• Click Add button. The device will now appear in the Camera List.
• To associate a device manually with the current Channel:
• Click Manually Add button.
• Enter the Local Name, IP Address, User Name, Password, Port Number and
Stream Type in the Camera Details section.
Note: The Port Number, User Name, Password and Stream Type can only be
modified in the WEB UI instead of Camera Setup screen.