Sercomm WAP121 Wireless-N Access Point with Power over Ethernet User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1592042
Application ID	kNIe6n/l55ReI3/Mx/yytA==
Document Description	User manual 4 of 4
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	81.59kB (1019867 bits)
Date Submitted	2011-12-01 00:00:00
Date Available	2011-12-01 00:00:00
Creation Date	2011-11-29 15:34:18
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2011-11-30 16:42:30
Document Title	untitled

Translated Safety Warnings
¡Advertencia!
Varning!
La instalación del equipo debe cumplir con las normativas de electricidad locales y nacionales.
Installation av utrustningen måste ske i enlighet med gällande elinstallationsföreskrifter.
Regulatory Compliance and Safety Information for the Cisco Small Business Wired and Wireless Routers, and Access Points (EMC
78-19314-01
19
Translated Safety Warnings
Statement 1075—Hazardous Voltage or Energy Present on DC Power
Terminals
Warning
Waarschuwing
Varoitus
Hazardous voltage or energy may be present on DC power terminals. Always replace cover
when terminals are not in service. Be sure uninsulated conductors are not accessible when cover
is in place.
Op DC-aansluitingspunten kunnen zich gevaarlijke voltages of energieën voordoen. Plaats
altijd de afsluiting wanneer de aansluitingspunten niet worden gebruikt Zorg ervoor dat
blootliggende contactpunten niet toegankelijk zijn wanneer de afsluiting is geplaatst.
Tasavirtaliittimissä saattaa olla huomattava jännite tai teho. Sulje suojus aina, kun liittimet
eivät ole käytössä. Suojuksen ollessa suljettuna varmista, että kohde on suojattu
eristämättömiltä johtimilta.
Attention
Le voltage ou l'énergie électrique des terminaux à courant continu peuvent être dangereux.
Veillez à toujours replacer le couvercle lors les terminaux ne sont pas en service. Assurez-vous
que les conducteurs non isolés ne sont pas accessibles lorsque le couvercle est en place.
Warnung
In mit Gleichstrom betriebenen Terminals kann es zu gefählicher Spannung kommen. Die
Terminals müssen abgedeckt werden, wenn sie nicht in Betrieb sind. Stellen Sie bei Benutzung
der Abdeckung sicher, dass alle nicht isolierten, stromführenden Kabel abgedeckt sind.
Avvertenza
I terminali di alimentazione DC potrebbero contenere voltaggio o energia pericolosi. Accertarsi
di sostituire il coperchio ogni qualvolta i terminali non sono operativi. Accertarsi che i
conduttori scoperti non siano accessibili quando il coperchio è inserito.
Advarsel
Det kan forekomme farlig spenning eller energi i likestrømsterminaler. Sett alltid dekselet på
plass når terminalene ikke er i bruk. Kontroller at uisolerte ledere ikke er tilgjengelige når
dekselet er på plass.
Aviso
Os terminais de corrente contínua podem fornecer tensão ou energia perigosa. Volte a colocar
a tampa, sempre que os terminais não estiverem a ser utilizados. Certifique-se de que os
condutores sem isolamento não estão acessíveis, quando a tampa estiver colocada.
¡Advertencia!
Puede haber energía o voltaje peligrosos en los terminales eléctricos de CC. Reemplace siempre
la cubierta cuando no estén utilizándose los terminales. Asegúrese de que no haya acceso a
conductores descubiertos cuando la cubierta esté colocada.
Varning!
20
Farlig spänning eller skadlig energi kan finnas i likströmsterminalerna. Sätt alltid tillbaka
höljet när terminalerna inte används. Försäkra att inga oisolerade ledare kan nås när höljet
sitter på plats.
Regulatory Compliance and Safety Information for the Cisco Small Business Wired and Wireless Routers, and Access Points (EMC
78-19314-01
Translated Safety Warnings
Statement 248—Unit Mounting Warning
Warning
Waarschuwing
This unit is intended to be mounted on a wall. Please read the wall mounting instructions
carefully before beginning installation. Failure to use the correct hardware or to follow the
correct procedures could result in a hazardous situation to people and damage to the system.
Deze eenheid dient aan een wand te worden bevestigd. Lees voordat u met de installatie begint,
de instructies voor wandmontage aandachtig door. Het niet gebruiken van de juiste apparatuur
of het niet volgen van de juiste procedures kan leiden tot gevaarlijke situaties of beschadiging
van het systeem.
Varoitus
Tämä laite on tarkoitettu seinälle asennettavaksi. Lue seinäasennusohjeet huolellisesti ennen
asennuksen aloittamista. Väärien työkalujen käyttäminen tai ohjeiden noudattamatta
jättäminen voi aiheuttaa henkilövahinkoja ja vioittaa laitetta.
Attention
Cette unité est conçue pour être montée sur un mur. Veuillez lire attentivement les instructions
de montage avant de commencer l'installation. L'utilisation d'un matériel incorrect ou
l'application inappropriée des procédures peut être à l'origine d'accidents et endommager le
système.
Warnung
Diese Einheit ist für die Montage an einer Wand bestimmt. Lesen Sie die Montageanweisungen
sorgfältig durch, bevor Sie mit der Installation beginnen. Nichtverwenden der korrekten
Hardware oder Nichtbefolgen der korrekten Vorgehensweise stellt eine potentielle
Gefahrenquelle dar und könnte das System beschädigen.
Avvertenza
L’unità deve essere montata a parete. Leggere attentamente le istruzioni di montaggio a parete
prima di procedere all’installazione. L’impiego di utensili non adeguati o di procedure non
corrette può comportare un rischio per le persone e per il sistema stesso.
Regulatory Compliance and Safety Information for the Cisco Small Business Wired and Wireless Routers, and Access Points (EMC
78-19314-01
21
European Directives
Advarsel
Denne enheten er beregnet på veggmontering. Les instruksjonene om veggmontering nøye før
du begynner installeringen. Hvis du ikke bruker riktig maskinutstyr eller følger de korrekte
prosedyrer, kan det medføre risiko for personskade og skade på systemet.
Aviso
Esta unidade foi concebida para ser montada numa parede. Leia atentamente as instruções de
montagem em parede antes de iniciar a instalação. A utilização de material incorrecto ou o não
seguimento dos procedimentos correctos podem dar origem a uma situação perigosa para o
pessoal e danificar o sistema.
¡Advertencia!
Esta unidad está diseñada para ser montada en la pared. Leer las instrucciones de montaje en
pared cuidadosamente antes de comenzar la instalación. En caso de no utilizar los materiales
apropiados o no seguir el procedimiento correcto, se podría crear una situación peligrosa y
ocasionar daños al sistema.
Varning!
Den här enheten är utformad för väggmontering. Läs noga anvisningarna för väggmontering
innan du börjar installera. Om du inte använder rätt maskinvara eller inte följer anvisningarna
kan det orsaka fara för personskada eller skador på systemet.
European Directives
Non-Radio Models (Not Fitted with Antenna or Antenna Connectors)
The following CE mark is affixed to the equipment and packaging:
Declaration of Conformity with Regard to the Directives 2006/95/EC and 2004/108/EC
This equipment complies with the essential requirements and other provisions of Directives 2006/95/EC
and 2004/108/EC. For more information, please refer to the Declaration of Conformity.
Radio Models (Models Fitted with Antenna or Antenna Connectors)
The following CE mark is affixed to the equipment and packaging:
22
Regulatory Compliance and Safety Information for the Cisco Small Business Wired and Wireless Routers, and Access Points (EMC
78-19314-01
European Directives
National Restrictions
Table 1 provides an overview of the regulatory power limits applicable for the 2.4-GHz bands.
Table 1
RCSI Power Limits
Frequency Band
(MHz)
Max Power Level (EIRP)
(mW)
2400-2483.5
100
Indoor Only
Indoor and Outdoor
5150-5350
200
5470-5725
1000
1. Dynamic Frequency Selection (DFS) and Transmit Power Control (TPC) are required in the 5250- to 5350-GHz and 5470- to
5725-GHz range.
Other Country Restrictions
Other countries have the following additional requirements or restrictions than those listed in Table 2.
France—For 2.4 GHz, the output power is restricted to 10 mW EIRP when the product is used outdoors
in the band 2454 – 2483,5 MHz. There are no restrictions when used indoors or when used in other parts
of the 2.4-GHz band.
Pour la bande 2.4-GHz, la puissance est limitée à 10 mW en p.i.r.e. pour les équipements utilisés en
extérieur dans la bande band 2454 – 2483,5 MHz.. Il n’y a pas de restrictions pour des utilisations en
intérieur ou dans d’autres parties de la bande 2,4 GHz. Consultez http://www.arcep.fr/ pour de plus
amples détails.
Italy—This product meets the National Radio Interface and the requirements specified in the National
Frequency Allocation Table for Italy. Unless this wireless LAN product is operating within the
boundaries of the owner’s property, its use requires a “general authorization”. Please check
http://www.comunicazioni.it/it/ for more details.
Questo prodotto è conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale
di ripartizione delle frequenze in Italia. Se non viene installato all’interno del proprio fondo, l’utilizzo
di prodotti Wireless LAN richiede una “Autorizzazione Generale”. Consultare
http://www.comunicazioni.it/it/ per maggiori dettagli.
Latvia—The outdoor usage of the 2.4 GHz band requires an authorization from the Electronic
Communications Office. Please check http://www.esd.lv for more details.
2,4 GHz frekvencu joslas izmantošanai arpus telpam nepieciešama atlauja no Elektronisko sakaru
direkcijas. Vairak informacijas: http://www.esd.lv.
Note
The regulatory limits for maximum output power are specified in Equivalent Isotropic Radiated Power
(EIRP). The EIRP level of a device can be calculated by adding the gain of the antenna used (specified
in dBi) to the output power available at the connector (specified in dBm).
Regulatory Compliance and Safety Information for the Cisco Small Business Wired and Wireless Routers, and Access Points (EMC
78-19314-01
23
European Directives
Statement 287—Declaration of Conformity to R&TTE Directive
1999/5/EC for the European Community, Switzerland, Norway, Iceland
and Liechtenstein
English:
This equipment is in compliance with the essential requirements and other relevant provisions
of Directive 1999/5/EC.
[Bulgarian]:
[Czech]:
Dansk
[Danish]:
Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i
Direktiv 1999/5/EF.
Deutsch
[German]:
Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden
Vorgaben der Richtlinie 1999/5/EU.
Eesti
[Estonian]:
See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele asjakohastele sätetele.
Español
[Spanish]:
Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva
1999/5/CE.
[Greek]:
Français
[French]:
Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la
Directive 1999/5/EC.
Íslenska
[Icelandic]:
Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar 1999/5/EC.
Italiano
[Italian]:
Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva
1999/5/CE.
Latviski
[Latvian]:
[Lithuanian]:
Nederlands
[Dutch]:
Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de
Richtlijn 1999/5/EC.
Malti
[Maltese]:
24
Regulatory Compliance and Safety Information for the Cisco Small Business Wired and Wireless Routers, and Access Points (EMC
78-19314-01
Standards Compliance for European Directives
Magyar
[Hungarian]:
Norsk
[Norwegian]:
Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i
EU-direktiv 1999/5/EF.
Polski
[Polish]:
Português
[Portuguese]:
Este equipamento está em conformidade com os requisitos essenciais e outras provisões
relevantes da Directiva 1999/5/EC.
[Romanian]:
Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi relevante ale
Directivei 1999/5/EC.
Slovensko
[Slovenian]:
Slovensky
[Slovak]:
Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji Direktive
1999/5/EC.
Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými nariadeniami
direktív: 1999/5/EC.
Suomi
[Finnish]:
Svenska
[Swedish]:
Standards Compliance for European Directives
This section includes all regulatory, safety, EMC, telecom, and radio standards used to verify compliance
with the EU Directive (Directive 2006/95/EC and 2004/108/EC for products without antenna or antenna
connectors and Directive 1995/5/EC for products with antenna or antenna connectors). The Cisco Small
Business Wired and Wireless Routers, and Access Points (EMC Class B Devices) is in compliance with
national and international standards as described in Table 2.
Table 2
Standards Compliance
Specification
Description
Safety
EN 60950 1
EN 60825 1
Products with Optical Ethernet:
EN 60825 2
Wireless Products:
EN 50385
Regulatory Compliance and Safety Information for the Cisco Small Business Wired and Wireless Routers, and Access Points (EMC
78-19314-01
25
EMC Class B Notices and Warnings
Table 2
Standards Compliance (continued)
Specification
Description
EMC
EN55022 Class A
EN50082
EN61000 6 1
EN55024
EN61000 3 2
EN61000 3 3
Wireless Products:
EN 301 489 1, EN 301 489 17
Radio
2.4 GHz 802.11 systems
EN 300 328
5.0 GHz 802.11 systems
EN 301 893
For specific details about the years, revisions and relevant amendments please refer to the applicable
declaration of conformity available at http://www.ciscofax.com.
EMC Class B Notices and Warnings
This section includes the EMC Class B warnings for the Cisco Wired and Wireless Routers and Access
Point Devices.
Class B Notice for FCC
Modifying the equipment without Cisco’s authorization may result in the equipment no longer
complying with FCC requirements for Class B digital devices. In that event, your right to use the
equipment may be limited by FCC regulations, and you may be required to correct any interference to
radio or television communications at your own expense.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
26
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Regulatory Compliance and Safety Information for the Cisco Small Business Wired and Wireless Routers, and Access Points (EMC
78-19314-01
EMC Class B Notices and Warnings
Class B Notice for Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Statement 295—Class B Warning for Korea
Warning
This is a Class B Device and is registered for EMC requirements for residential use. This device
can be used not only in residential areas but in all other areas.
Statement 157—VCCI Compliance for Class B Equipment
Warning
This is a Class B product based on the standard of the VCCI Council. If this is used near a radio
or television receiver in a domestic environment, it may cause radio Interference. Install and
use the equipment according to the instruction manual.
VCCI-B
Regulatory Compliance and Safety Information for the Cisco Small Business Wired and Wireless Routers, and Access Points (EMC
78-19314-01
27
Japanese Electric Appliance and Radio Laws
Japanese Electric Appliance and Radio Laws
Statement 371—Power Cable and AC Adapter
Warning
When installing the product, please use the provided or designated connection cables/power
cables/AC adaptors/batteries. Using any other cables/adaptors could cause a malfunction or a
fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that
have the “UL” or “CSA” shown on the cord), not regulated with the subject law by showing
"PSE" on the cord, for any other electrical devices than products designated by CISCO.
Statement 372—Wireless LAN Products
All wireless LAN products in the 5.2/5.3GHz band cannot be used outdoors. Use the product only
indoors.
Radio
This section describes radio compliance conditions for the Cisco Small Business Wired and Wireless
Routers, and Access Points (EMC Class B Devices).
Caution
The Part 15 radio device operates on a non-interference basis with other devices operating at this
frequency when using the integrated antennas. Any changes or modification to the product not expressly
approved by Cisco could void the user’s authority to operate this device.
Caution
This device operates in the 5150-5250MHz and 5470-5725MHz bands and is therefore restricted to
indoor operation only (per FCC guidance). The use of this system outdoors is not in compliance with
FCC regulations or guidelines.
Please contact your Cisco salesperson for additional details.
28
Regulatory Compliance and Safety Information for the Cisco Small Business Wired and Wireless Routers, and Access Points (EMC
78-19314-01
Product Usage Restrictions
Product Usage Restrictions
With the exception of the Cisco WAP200E Wireless-G Exterior Access Point, these products are
intended for indoor use only.
Authorized External Antennas and Corresponding Power
Levels
Cisco’s 2.4-GHz wireless products have either integral antennas or external (dedicated) antennas.
This product is designed for use with the standard, integral or dedicated (external) antenna(s) that is/are
shipped together with the equipment. To compensate for alternative cable and antenna combinations, it
may be necessary to change the transmit power level. Combinations of extension cables and antennas
resulting in a radiated power level exceeding 100 mW EIRP are illegal.
Power Level Settings
For wireless adapters operating in the 2,4-GHz band, the typical radiated output power is 18 dBm EIRP,
while the maximum radiated output power will not exceed 20 dBm (100 mW) EIRP.
Use the Web-based Utility to configure its power output setting (refer to the product’s documentation
for more information).
Canadian Compliance Statement
Cisco 2.4-GHz and 5.0-GHz Access Points in Wireless Routers are certified to the requirements of
RSS-210 for 2.4-GHz and 5.0-GHz spread spectrum devices. The use of this device in a system operating
either partially or completely outdoors may require the user to obtain a license for the system according
to the Canadian regulations. For further information, contact your local Industry Canada office.
Guidelines for Operating Cisco Wireless Access Points and Wireless
Routers in Japan
This section provides guidelines for avoiding interference when operating Cisco wireless access points
in Japan. These guidelines are provided in both English and Japanese.
English Translation
This equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices
such as microwave ovens and mobile object identification (RF-ID) systems (licensed premises radio
stations and unlicensed specified low-power radio stations) used in factory production lines.
1.
Before using this equipment, make sure that no premises radio stations or specified low-power radio
stations of RF-ID are used in the vicinity.
2.
If this equipment causes RF interference to a premises radio station of RF-ID, promptly change the
frequency or stop using the device; contact the number below and ask for recommendations on
avoiding radio interference, such as setting partitions.
Regulatory Compliance and Safety Information for the Cisco Small Business Wired and Wireless Routers, and Access Points (EMC
78-19314-01
29
Authorized External Antennas and Corresponding Power Levels
3.
If this equipment causes RF interference to a specified low-power radio station of RF-ID, contact
the number below.
Contact Number: 03-5549-6500
03-6434-6500
43768
Japanese Translation
Administrative Rules for Cisco Wireless Devices in Taiwan
This section provides administrative rules for operating Cisco wireless access products in Taiwan. The
rules are provided in both Chinese and English.
Wireless Devices with IEEE 802.11a/b/g Radios
Chinese Translation
English Translation
This equipment is limited for indoor use.
30
Regulatory Compliance and Safety Information for the Cisco Small Business Wired and Wireless Routers, and Access Points (EMC
78-19314-01
Authorized External Antennas and Corresponding Power Levels
All Access Wireless Products
Chinese Translation
English Translation
Administrative Rules for Low-Power Radio-Frequency Devices
Article 12
For those low-power radio-frequency devices that have already received a type-approval, companies,
business units, or users should not change its frequencies, increase its power, or change its original
features and functions.
Article 14
The operation of the low-power radio-frequency devices is subject to the conditions that no harmful
interference is caused to aviation safety and authorized radio stations; and if interference is caused, the
user must stop operating the device immediately and can’t re-operate it until the harmful interference is
clear.
The authorized radio station means a radio-communication service operating in accordance with the
Communication Act.
The operation of the low-power radio-frequency devices is subject to the interference caused by the
operation of an authorized radio station, by another intentional or unintentional radiator, by industrial,
scientific and medical (ISM) equipment, or by an incidental radiator.
Regulatory Compliance and Safety Information for the Cisco Small Business Wired and Wireless Routers, and Access Points (EMC
78-19314-01
31
Generic Discussion on RF Exposure
An FCC-compliant telephone cord and modular plug is provided with this equipment, designed to be
connected to the telephone network or premises wiring using a compatible modular jack that is Part 68
compliant.
This equipment cannot be used on telephone company provided coin service. Connection to party line
service is subject to state tariffs.
If this equipment causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. If advance notice isn't practical, the
telephone company will notify the customer as soon as possible. Also, you will be advised of your right
to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations, or procedures that
could affect the operation of the equipment. If this happens, the telephone company will provide advance
notice in order for you to make the necessary modifications in order to maintain uninterrupted service.
If trouble is experienced with this equipment, please contact us for repair and warranty information. If
the trouble is causing harm to the telephone network, the telephone company may request you remove
the equipment from the network until the problem is resolved.
It is recommended that the customer install an AC surge arrestor in the AC outlet to which this device
is connected. This is to avoid damage to the equipment caused by local lightning strikes and other
electrical surges.
Generic Discussion on RF Exposure
The Cisco products are designed to comply with the following national and international standards on
Human Exposure to Radio Frequencies.
•
US 47 Code of Federal Regulations Part 2 Subpart J
•
American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers /
IEEE C 95.1 (92)
•
International Commission on Non Ionizing Radiation Protection (ICNIRP) 98
•
Ministry of Health (Canada) Safety Code 6. Limits on Human Exposure to Radio Frequency Fields
in the range from 3kHz to 300 GHz
•
Australia Radiation Protection Standard
To ensure compliance with various national and international Electromagnetic Field (EMF) standards,
the system should only be operated with Cisco approved antennas and accessories.
US
This system has been evaluated for RF exposure for Humans in reference to ANSI C 95.1 (American
National Standards Institute) limits. The evaluation was based on evaluation per ANI C 95.1 and FCC
OET Bulletin 65C rev 01.01. The minimum separation distance from the antenna to general bystander
is 7.9 inches (20cm) to maintain compliance.
Canada
This system has been evaluated for RF exposure for Humans in reference to ANSI C 95.1 (American
National Standards Institute) limits. The evaluation was based on evaluation per RSS-102 Rev 2. The
minimum separation distance from the antenna to general bystander is 7.9 inches (20cm) to maintain
compliance.
32
Regulatory Compliance and Safety Information for the Cisco Small Business Wired and Wireless Routers, and Access Points (EMC
78-19314-01
Declarations of Conformity
EU
This system has been evaluated for RF exposure for Humans in reference to the ICNIRP (International
Commission on Non-Ionizing Radiation Protection) limits. The evaluation was based on the EN 50385
Product Standard to Demonstrate Compliance of Radio Base stations and Fixed Terminals for Wireless
Telecommunications Systems with basic restrictions or reference levels related to Human Exposure to
Radio Frequency Electromagnetic Fields from 300 MHz to 40 GHz. The minimum separation distance
from the antenna to general bystander is 20cm (7.9 inches).
Australia
This system has been evaluated for RF exposure for Humans as referenced in the Australian Radiation
Protection standard and has been evaluated to the ICNIRP (International Commission on Non-Ionizing
Radiation Protection)limits. The minimum separation distance from the antenna to general bystander
is 20cm (7.9 inches).
Generic Statements - for other countries
ANSI C 95.1 (99)
This system has been evaluated for RF exposure for Humans in reference to the ANSI (American
National Standards Institute)limits as referenced in C 95.1 (99). The minimum separation distance
from the antenna to the user is 7.9 inches (20cm).
ICNIRP Limits
This system has been evaluated for RF exposure for Humans in reference to the ICNIRP (International
Commission on Non-Ionizing Radiation Protection) limits. The minimum separation distance from the
antenna to the user is 20cm (7.9 inches).
Declarations of Conformity
The Declaration of Conformity statements for this product can be found at the following URL:
http://www.ciscofax.com
Note
If you still have questions regarding the compliance of these products or you cannot find the information
you are looking for, please send an e-mail request to complianceinfo@cisco.com.
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks
can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word
partner does not imply a partnership relationship between Cisco and any other company. (1005R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any
examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only.
Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
© 2010 Cisco Systems, Inc. All rights reserved.
Regulatory Compliance and Safety Information for the Cisco Small Business Wired and Wireless Routers, and Access Points (EMC
78-19314-01
33
REVIEW DRAFT — CISCO CONFIDENTIAL
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance
could void your authority to operate the equipment.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
RF exposure warning: The equipment complies with RF exposure limits set forth for an uncontrolled
environment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Déclarations d'exposition aux RF liéesAvertissement d'exposition RF: L'équipement est conforme aux limites
d'exposition aux RF établies pour un environnement non contrôlé. L'antenne (s) utilisée pour ce transmetteur ne
doit pas être co-localisés ou fonctionnant en conjonction avec une autre antenne ou transmetteur.
This device complies with Industry Candada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation of the device.
Ce dispositif est conforme à la norme de l'industrie Candada exempts de licence RSS (s). L'opération est soumise
aux deux conditions suivantes: (1) Cet appareil ne peut causer d'interférences nuisibles, et (2) cet appareil doit
accepter toute interférence reçue, y compris les interférences qui peuvent causer un mauvais fonctionnement
de l'appareil.
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found
at ZZZFLVFRFRPJRWUDGHPDUNV. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply
a partnership relationship between Cisco and any other company. (1005R)
© 2012 Cisco Systems, Inc. All rights reserved.
Document Revision Number ###

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Extract
Page Count                      : 16
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:54bce34e-47d3-4fd2-bfcd-c7bc2b00eb47
Modify Date                     : 2011:11:30 16:42:30+08:00
Create Date                     : 2011:11:29 15:34:18+08:00
Metadata Date                   : 2011:11:30 16:42:30+08:00
Document ID                     : uuid:c94a9e38-37ed-42e1-83eb-4414ed9de3a3
Format                          : application/pdf
Title                           : untitled
Producer                        : Acrobat Distiller 6.0 (Windows)

EXIF Metadata provided by EXIF.tools