Servis Rhino Brush Cutter Fs15 Users Manual FS15,FS10 COVER.p65
FS15 to the manual 2b5a5326-a850-4986-9382-b6d49691de70
2015-02-02
: Servis-Rhino Servis-Rhino-Brush-Cutter-Fs15-Users-Manual-490774 servis-rhino-brush-cutter-fs15-users-manual-490774 servis-rhino pdf
Open the PDF directly: View PDF .
Page Count: 84
Download | |
Open PDF In Browser | View PDF |
FS15 FLEX-WING ROTARY CUTTER P/N 00773425MB Published 07-05 MASTER PARTS BOOK S/N 00101 TO 10429 PARTS LISTING Rhino® An Alamo Group Company 1020 S. Sangamon Ave. Gibson City, Il 60936 1-800-446-5158 Email: parts@servis-rhino.com © 2005 Alamo Group Inc. TO THE OWNER/OPERATOR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death. PARTS SECTION Parts Section – 1 PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. NOTE: Please refer to The Safety Section in the front of this Manual for the proper Part Number when ordering Replacement Safety Decals. For maximum safety and to guarantee optimum product reliability, always use genuine Servis-Rhino Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to: RHINO ® 1020 S. Sangamon Ave. Gibson City, IL 60936 800-446-5158 Email: parts@servis-rhino.com ©2005 Alamo Group Inc. Parts Section – 2 PART NAME INDEX AXLE ASSEMBLY - CTR & WING S/N 00101 - 10147 OCT 1977 - JAN 1988.................................................................... 5 AXLE ASSEMBLY - CTR & WING S/N 10148 - 10429 JAN 1988 - MAY 1988.................................................................... 6 BLADE BAR ASSEMBLY - CTR HEAVY DUTY S/N 01162 - 10429 DEC 1980 - MAY 1988.............................................. 7 BLADE BAR ASSEMBLY - CTR STANDARD S/N 00101 - 01162 OCT 1977 - DEC 1980 ................................................. 8 BLADE BAR ASSEMBLY - WING HEAVY DUTY S/N 01162 - 10429 DEC 1980 - MAY 1988 ........................................... 9 BLADE BAR ASSEMBLY - WING STANDARD S/N 01162 - 10429 OCT 1977 - DEC 1980 ............................................. 10 BLADE PAN ASSEMBLY - CTR HEAVY DUTY S/N 01162 - 10429 DEC 1980 - MAY 1988............................................ 11 BLADE PAN ASSEMBLY - CTR STANDARD S/N 00101 - 01162 OCT 1977 - DEC 1980 ............................................... 12 BLADE PAN ASSEMBLY - WING HEAVY DUTY S/N 01162 - 10429 DEC 1980 - MAY 1988 ......................................... 13 BLADE PAN ASSEMBLY - WING STANDARD S/N 00101 - 01162 OCT 1977 - DEC 1980 ............................................. 14 CHAIN GUARD - CENTER & WING SECTION S/N 01497 - 10429 JUN 1982 - MAY 1988 ............................................. 15 CHAIN GUARD - REAR CENTER SECTION S/N 01497 - 10429 JUN 1982 - MAY 1988................................................. 16 CHAIN GUARD - REAR WING SECTION S/N 01497 - 10429 JUN 1982 - MAY 1988...................................................... 17 CYLINDER ASSEMBLY - CENTER AXLE S/N 00101 - 01377 OCT 1977 - JAN 1982...................................................... 18 CYLINDER ASSEMBLY - CENTER AXLE S/N 00101 - 10429 OCT 1977 - MAY 1988..................................................... 19 CYLINDER ASSEMBLY - CENTER AXLE S/N 01376 - 10429 JAN 1982 - MAY 1988 ..................................................... 20 CYLINDER ASSEMBLY - LEVEL LIFT - 2-1/2 X 8 SLAVE CYL S/N 00101 - 10429 OCT 1977 - MAY 1988................... 21 CYLINDER ASSEMBLY - LEVEL LIFT - 2-3/4 X 8 SLAVE CYL S/N 00101 - 10429 OCT 1977 - MAY 1988................... 22 CYLINDER ASSEMBLY - LEVEL LIFT - 3 X 8 SLAVE CYL S/N 00101 - 10429 OCT 1977 - MAY 1988......................... 23 CYLINDER ASSEMBLY - LEVEL LIFT REPLACEMENT ASSY (P/N 8719) S/N 00101 - 10429 OCT 1977 - MA ............ 24 CYLINDER ASSEMBLY - LEVEL LIFT REPLACEMENT ASSY (P/N 8720) S/N 00101 - 10429 OCT 1977 - MA ............ 25 CYLINDER ASSEMBLY - LEVEL LIFT REPLACEMENT ASSY (P/N 8721) S/N 00101 - 10429 OCT 1977 - MA ............ 26 CYLINDER ASSEMBLY - WING-HYDRAULIC CYLINDER & HOSE GROUP S/N 00101 - 01376 OCT 1977 - JAN ....... 27 CYLINDER ASSEMBLY - WING-LANTEX HYDRAULIC CYL & HOSE GRP S/N 01377 - 10429 JAN 1982 - MAY......... 28 CYLINDER ASSEMBLY - WING-REPLACEMENT S/N 00101 - 10429 OCT 1977 - MAY 1988........................................ 29 DECALS S/N 00101 - 10429 OCT 1977 - MAY 1988.......................................................................................................... 30 DEFLECTOR - REAR WING S/N 01497 - 10429 JUN 1982 - MAY 1988 .......................................................................... 31 DEFLECTOR - RUBBER FRONT CENTER S/N 00101 - 10429 OCT 1977 - MAY 1988 .................................................. 32 DEFLECTOR - RUBBER FRONT WING LEFT & RIGHT S/N 00101 - 10429 OCT 1977 - MAY 1988 ............................. 33 DEFLECTOR - RUBBER LEFT & RIGHT CENTER S/N 00101 - 10429 OCT 1977 - MAY 1988...................................... 34 DRIVELINE ASSEMBLY - CTR GEARBOX SQUARE SHAFT SLIP 35R S/N 00101 - 10429 OCT 1977 - MAY 19......... 35 DRIVELINE ASSEMBLY - OUTBOARD SQUARE SHAFT ASSEMBLY 35R S/N 00101 - 10429 OCT 1977 - MAY 1 ..... 36 DRIVELINE ASSEMBLY - PTO SQUARE SHAFT ASSEMBLY 44R S/N 00101 - 10429 OCT 1977 - MAY 1988............ 37 DRIVELINE ASSEMBLY - SHIELDING ASSEMBLY SQUARE SHAFTS S/N 00101 - 10429 OCT 1977 - MAY 198 ....... 38 GEARBOX ASSEMBLY - CENTER SECTION S/N 00101 - 10429 OCT 1977 - MAY 1988 .............................................. 40 GEARBOX ASSEMBLY - DIVIDER (COMER) S/N 01901 - 10429 FEB 1985 - MAY 1988 ............................................... 42 GEARBOX ASSEMBLY - DIVIDER S/N 00101 - 01900 OCT 1977 - FEB 1985 ................................................................ 44 GEARBOX ASSEMBLY - LEFT WING S/N 00101 - 10429 OCT 1977 - MAY 1988 .......................................................... 46 GEARBOX ASSEMBLY - RIGHT WING S/N 00101 - 10429 OCT 1977 - MAY 1988 ........................................................ 48 GEARBOX ATTACHMENT - DIVIDER & CENTER GEARBOX S/N 00101 - 10429 OCT 1977 - MAY 1988.................... 50 GEARBOX ATTACHMENT- RIGHT & LEFT WING GEARBOX S/N 00101 - 10429 OCT 1977 - MAY 1988 ................... 51 HOSE BRACKET COMPONENTS S/N 00101 - 10429 OCT 1977 - MAY 1988................................................................. 52 HUB ASSEMBLY - CENTER & OUTBOARD S/N 10148 - 10428 JAN 1988 - MAY 1988 ................................................. 53 HUB ASSEMBLY - OUTBOARD AXLES S/N 00101 - 10147 OCT 1977 - JAN 1988 ........................................................ 54 HUB ASSEMBLY - STANDARD CENTER AXLE S/N 00101 - 10147 OCT 1977 - JAN 1988 ........................................... 55 HYDRAULIC CONTROL VALVE MOUNTING KIT S/N 00101 - 10429 OCT 1977 - MAY 1988 ........................................ 56 HYDRAULIC HOSE ADAPTERS S/N 00101 - 10429 OCT 1977 - MAY 1988 ................................................................... 57 HYDRAULIC VALVE ASSEMBLY - DETENT W/SPRING ASSEMBLY S/N 00101 - 10429 OCT 1977 - MAY 1988 ........ 58 HYDRAULIC VALVE ASSEMBLY - OPEN/CLOSED CENTER VALVE S/N 00101 - 10429 OCT 1977 - MAY 1988........ 59 JACK ASSEMBLY - TOP WING S/N 00101 - 10429 OCT 1977 - MAY 1988 .................................................................... 60 LEFT SCREW S/N 00101 - 10429 OCT 1977 - MAY 1988................................................................................................. 61 LEVEL LIFT KIT FIELD INSTALLATION S/N 00101 - 10429 OCT 1977 - MAY 1988 ....................................................... 62 LEVEL LIFT ROD ASSEMBLY S/N 10148 - 10428 JAN 1988 - MAY 1988 ....................................................................... 63 MAINFRAME ASSEMBLY S/N 00101 - 01900 OCT 1977 - FEB 1985............................................................................... 64 MAINFRAME ASSEMBLY S/N 01901 - 10429 FEB 1985 - MAY 1988 .............................................................................. 65 NOTES.................................................................................................................................................................................. 39 SIDE SHOE & SIDE SKIRT - OFFSET MODELS CTR SECTION S/N 00101 - 10429 OCT 1977 - MAY 1988................ 66 SIDE SHOE & SIDE SKIRT S/N 00101 - 10429 OCT 1977 - MAY 1988 ........................................................................... 67 SKID SHOE ASSEMBLY S/N 00101 - 00466 OCT 1977 - FEB 1979 ................................................................................ 68 SKID SHOE ASSEMBLY S/N 00101 - 10429 OCT 1977 - MAY 1988................................................................................ 69 SPRING ASSEMBLY - CENTER AXLE S/N 00101 - 10429 OCT 1977 - MAY 1988 ......................................................... 70 SPRING ASSEMBLY - WING S/N 00101 - 10429 OCT 1977 - MAY 1988 ........................................................................ 71 TIRE/WHEEL ASSEMBLY S/N 00101 - 10429 OCT 1977 - MAY 1988 ............................................................................. 72 FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 3 PART NAME INDEX TONGUE ASSEMBLY S/N 00101 - 10429 OCT 1977 - MAY 1988 .................................................................................... TORQUE LIMITER ASSEMBLY S/N 00101 - 10001 OCT 1977 - AUG 1987..................................................................... TORQUE LIMITER ASSEMBLY S/N 10001 - 10429 AUG 1987 - MAY 1988 .................................................................... WEIGHT BOX S/N 00101 - 10429 OCT 1977 - MAY 1988................................................................................................. WINCH AND STAND ASSSEMBLY S/N 00101 - 10429 OCT 1977 - MAY 1988............................................................... FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 4 73 74 75 76 77 AXLE ASSEMBLY - CTR & WING S/N 00101 - 10147 OCT 1977 - JAN 1988 ITEM PART NO. QTY. DESCRIPTION 1 0656060100 0656280100 0656070110 0656070100 0656070210 0656070200 20BH5012 15B1600 65106A4 D121 D301 0652140220 0652140210 0652140260 0652140250 1 1 1 1 1 1 4 4 4 1 1 1 15 1 1 CENTER AXLE WELD NOT SHOWN DOUBLE AXLE WELD SHOWN AXLE WLD R.H. ONLY AXLE ASSY AXLE WLD L.H. ONLY AXLE ASSY PIN-SPIRAL 5/16 X 1 1/2 * WASHER 1 SAE P * WLDMT,AXLE PIVOT PIN * DECAL ADJ-NUTS DECAL,RHINO WLDMT, AXLE ARM - LEFT ** LEFT AXLE ASSY ** WLDMT, AXLE ARM - RIGHT RIGHT AXLE ASSY ** 5 6 7 8 9 10 11 15 16 Note: This Axle uses hub #3741247 assembly on center and hub #271033 assembly on wing. Washers are welded to spindle on center axle but not on the wing. FOR REPLACEMENT PARTS ONLY *QTY SHOWN FOR 1 MACHINE, COMPLETE **USED W/FACTORY LEVEL LIFT ONLY ITEM #15 AND #16 FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 5 AXLE ASSEMBLY - CTR & WING S/N 10148 - 10429 JAN 1988 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 00756458 00756456 00756461 00756464 00756455 00756457 00756459 00756462 20BH5012 15B1600 65106A4 D121 D301 00756466 00756468 00756465 00756467 1 1 1 1 1 1 1 1 4 4 4 1 1 1 1 1 1 AXLE CENTER ASSY NOT SHOWN AXLE DOUBLE CENTER SHOWN AXLE ARM ASSY (R.H.), COMPLETE W/1 HUB AXLE ARM ASSY(L.H.), COMPLETE W/1 HUB DOUBLE AXLE ARM WELD SHOWN CENTER AXLE WELD NOT SHOWN AXLE WELD (R.H.) ONLY AXLE WELD (L.H.) ONLY PIN-SPIRAL 5/16 X 1 1/2 * WASHER 1 SAE P * WLDMT,AXLE PIVOT PIN * DECAL ADJ-NUTS DECAL,RHINO LEFT AXLE ARM ASSY RIGHT AXLE ARM ASSY LEFT AXLE ARM WELD N/S RIGHT AXLE ARM WELD 2 3 4 5 6 7 8 9 10 11 12 13 15 16 Note: This axle center & win uses hub #00757241 assembly. FOR REPLACEMENT PARTS ONLY. *QTY SHOWN FOR 1 MACHINE, COMPLETE **USED W/FACTORY HYDRAULIC LEVEL LIFT ONLY ITEM #12 THRU #16 FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 6 BLADE BAR ASSEMBLY - CTR HEAVY DUTY S/N 01162 - 10429 DEC 1980 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 0656160100 0652010030 571044 571045 5GL16140 0622010330 0656150200 1 2 2 2 2 2 2 WLDMT, BLADE CARRIER BLADE, CCW/CW FLAT BOLT SHOULDER WASHER LOCKNUT 1 -14 LH TLN PL BLADE, CCW FAN WASHER,SQ HOLE HT Note: This carrier was optional until Dec. 1980 then, it became standard. These blade bolts have square shoulders. The blade bolt hole is 1-25/64 diameter. Check Before Ordering Parts FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 7 BLADE BAR ASSEMBLY - CTR STANDARD S/N 00101 - 01162 OCT 1977 - DEC 1980 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 701021R 701022R 36107A2ALH 481043 5GL12160 71103 1 2 2 2 2 2 CARRIER,BAR BLADE BLADE BOLT SHOULDER L.H THREAD SPCR 1-1/4 X 3/4 X 5/16 LOCKNUT TLM 3/4 NF PLB L.H. THREAD BLD,OFT/FAN,CCW Note: This blade carrier was standard till Dec. 1980. These Blade bolts have round shoulder. The blade bolt hole is 1-1/64 dia. Check Before Ordering Parts FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 8 BLADE BAR ASSEMBLY - WING HEAVY DUTY S/N 01162 - 10429 DEC 1980 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 0656180100 0652010030 0622010330 0652010330 571044 571045 5GL16140 0656150200 1 2 2 3 2 2 2 2 WLDMT, BLADE CARRIER, FS15 BLADE, CCW/CW FLAT BLADE, CCW FAN BLADE, CW FAN BOLT SHOULDER WASHER LOCKNUT 1 -14 LH TLN PL WASHER,SQ HOLE HT 4 5 6 7 Note: This was optional till Dec. 1980. These blades bolts have square shoulders. The blade bolt hole is 1-25/64 dia. Check Before Ordering Parts FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 9 BLADE BAR ASSEMBLY - WING STANDARD S/N 01162 - 10429 OCT 1977 - DEC 1980 ITEM PART NO. QTY. DESCRIPTION 1 2 711021 701022R 0656240000 71103 36107A2ALH 5312316 5GL12160 1 2 2 2 2 2 2 BLADE CARRIER BLADE BLADE STD FAN BLD,OFT/FAN,CCW BOLT SHOULDER WASHER (SPECIAL) LOCKNUT TLM (LH) 3/4 NF PLB 3 4 5 6 Note: This blade carrier was optional till Dec. 1980. The blade bolt hole is 1-1/64 dia. Check Before Ordering Parts FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 10 BLADE PAN ASSEMBLY - CTR HEAVY DUTY S/N 01162 - 10429 DEC 1980 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 0656150100 701332 0652010030 0652010030 0622010330 571044 7AH5101816 0656150200 571045 W67 00749136 5GL1640 1 1 2 3 2 2 4 2 2 4 4 2 BALDE CARRIER WELDMENT DISHPAN OFFSET FLAT BLADE HARD SURFACED OFFSET FLAT BLADE OFFSET FAN BLADE OFFSET HARD SURFACED FAN BLADE BOLT SPACER WASHER SHOULDER BOLT HARD WASHER LOCKNUT LOCKNUT L.H. THREAD 4 5 6 7 8 9 10 11 Note: This carrier was optional until Dec. 1980 then, it became standard. These blade bolts have square shoulders. The blade bolt hole is 1-25/64 diameter. Check Before Ordering Parts FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 11 BLADE PAN ASSEMBLY - CTR STANDARD S/N 00101 - 01162 OCT 1977 - DEC 1980 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 701333 701332 701022R 71103 HS71103 36107A2ALH 7AH5101816 671044 681064 W67 5GR10180 5GL12160 1 1 2 2 2 2 4 2 2 4 4 2 CARRIER BLADE WELDMENT DISHPAN BLADE, OFFSET FLAT BLADE, OFFSET FAN BLADE OFFSET FAN (HARD SURFACED) SHOULDER BLADE BOLT BOLT SPACER WASHER WASHER (HARDENED) WASHER (HARDENED) NUT-TOPLOCK NUT-TOPLOCK LH THREAD 5 6 7 8 9 10 11 Note: This blade carrier was standard till Dec. 1980. These Blade bolts have round shoulder. The blade bolt hole is 1-1/64 dia. Check Before Ordering Parts FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 12 BLADE PAN ASSEMBLY - WING HEAVY DUTY S/N 01162 - 10429 DEC 1980 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 0656170100 671042 0652010030 0652010030 0652010030 0652010030 0622010330 0622010330 0652010330 0652010330 571044 571045 7AH5101816 W67 00749136 5GL16140 0656150200 1 1 2 3 2 3 2 4 2 2 2 2 4 4 4 2 2 BLADE CARRIER, WELDMENT BLADE PAN OFFSET FLAT BLADE, CCW OFFSET FLAT BLADE, HARD SURFACED, CCW OFFSET FLAT BLADE, CW OFFSET FLAT BLADE, HARD SURFACED, CW OFFSET FAN BLADE, CCW OFFSET FAN BLADE, HARD SURFACED, CCW OFFSET FAN BLADE, CW FAN, BLADE HARD SURFACED, CW SHOULDER BOLT (L.H. THREADS) SHOULDER BOLT WASHER BOLT WASHER LOCKNUT LOCKNUT L.H. THREADS WASHER SPACER 4 5 6 7 8 9 10 11 Note: This was optional till Dec. 1980. These blades bolts have square shoulders. The blade bolt hole is 1-25/64 dia. Check Before Ordering Parts FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 13 BLADE PAN ASSEMBLY - WING STANDARD S/N 00101 - 01162 OCT 1977 - DEC 1980 ITEM PART NO. QTY. DESCRIPTION 1 2 3 671041 671042 701022R 0656240000 0656240000 71103 0656240000 71103 0656240000 36107A2ALH 5312316 7AH5101816 W67 00749136 5GI12160 671044 1 1 2 2 2 2 2 2 2 2 2 4 4 4 2 2 CARRIER, BLADE (WELDMENT) BLADE PAN BLADE, OFFSET, CCW BLADE, OFFSET, CW (HARD SURFACE) BLADE, OFFSET, CW BLADE, SUCTION, CCW BLADE, SUCTION, CW BLADE, SUCTION, HARD SURFACED, CCW BLADE, SUCTION, HARD SURFACED, CW BOLT, SHOULDER L.H. THD. WASHER, SPECIAL (HEAT TREATED) BOLT WASHER, HARD NUT, LOCK HEX. NUT, LOCK HEX. WASHER, SPACER 4 5 6 7 8 9 10 11 Note: This blade carrier was optional till Dec. 1980. The blade bolt hole is 1-1/64 dia. Check Before Ordering Parts FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 14 CHAIN GUARD - CENTER & WING SECTION S/N 01497 - 10429 JUN 1982 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 6 7 8 9 10 0652100000 0652100100 0652100200 0652100110 0652100201 0652100101 0652100203 0652100202 0652100104 0652100102 0652100105 7A81312 11 12 00013300 15B800 13 5GR8130 1 1 1 1 69 63 1 2 1 2 7 5 2 7 7 7 7 CHAIN GUARDS, FRONT CTR SECT FRNT CHN GD ASSY FRNT CHN GD ASSY, WING * WLDMT, MOUNTING BRACKET GUARD MNTING BRKT * CHAIN 5/16 5-LINKS CHAIN 5/16, 6 LINK * ROD CHAIN * ROD CHAIN ROD CHAIN ROD CHAIN C/S1/2 X 1 1/2 NC (WING) * HEXB 1/2 NC 2 PL5 * WASHER 1/2 SAE ZP (WING) * NUT,LOCKNUT 1/2 NC (WING) * 1 2 3 4 5 Note: These replace assembly used prior to Serial #07497 June 1982. Chain Guards with chain links welded on longer available. Leading edge of mower will be turned down 90` approximately. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 15 CHAIN GUARD - REAR CENTER SECTION S/N 01497 - 10429 JUN 1982 - MAY 1988 ITEM 1 2 3 4 5 6 7 ?8 PART NO. QTY. DESCRIPTION 0652110000 0652110100 0652110101 0652100203 0652110102 00748823 00752680 15B800 00001800 0652110103 652053 1 1 57 1 4 2 6 6 2 2 CHAIN GUARDS, REAR * REAR CHN GD ASSY, CTR SECT MOUNTING BRACKET CHAIN 5/16, 6 LINK ROD,CHAIN GUARD 52 1/2 LG HHCS 1/2-13UNC 1-1/2 PL5 HHCS 1/2-13UNC X 4LG PL5 WASHER 1/2 SAE ZP LOCKNUT TLM 1/2 NC PLB ROD,CHAIN GUARD 11 1/2 LG SPACER Note: These chain guards as an assembly replace earlier chain guards prior to serial #01497 June 1982. Chain guards with chain links welded on bracket are no longer available. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 16 CHAIN GUARD - REAR WING SECTION S/N 01497 - 10429 JUN 1982 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 0652110300 0652110200 0652110210 0652110310 00751126 0652110201 00013300 652053 00752680 7A81336 1 1 1 2 110 2 2 8 6 2 LEFT REAR WING CHN GD RT REAR CHN GD ASSY MOUNTING BRKT, RIGHT MOUNTING BRKT, LEFT CHAIN 5/16 WLD 6 LINK ROD CHAIN HEXB 1/2 NC 2 PL5 SPACER HHCS 1/2-13UNC X 4LG PL5 C/S1/2 X 4-1/2 NC PL5 2 3 4 5 9 10 12 Complete Rear Chain Guard Assembly to include center, left and right wing. See Center Chain Guard Section. These are the same for all previous serial #’s listed without modification. Chain Guards with welded on links are no longer available. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 17 CYLINDER ASSEMBLY - CENTER AXLE S/N 00101 - 01377 OCT 1977 - JAN 1982 ITEM PART NO. QTY. DESCRIPTION 1 65113B1 00759946 00755234 651302 94514 691354 65113A3 65113B6 651136 65113B8 65113A8 65113A9 651139 6511310 691315 6511311 65113A12 0651130001 8354 37107B13 65113A16 0651130017 6511320 00001200 00999316 6511322 00013901 6511324 00749508 2717100 6511325A 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 4 4 1 1 4 1 1 1 1 - CYLINDER CYLINDER 3 X 8 W/1-1/4 ROD CONTROL SPACER KIT HOSE #6 - 8 MP - 8 MP 180 LG ADAPTER, HYD, ELBOW SWIVEL CLEVIS 1 1/4-12 NF THD CLEVIS 1/16-12 NF THD COLLAR COLLAR HEAD 1 1/4 ROD 3 BR HEAD 1 1/16 ROD 3 BR ROD 1 1/4 ROD, 1-1/16 DIA.,3/4NF THDS. TUBE CENTER CYL PISTON, 3, O RING SEAL PISTON, 3, UCUP SEAL CLEVIS BASE 1/2 CLEVIS BASE 7/16 PIN-HYD. CYLINDER CLIP-X HAIR PIN TIE ROD 1/2 - 13 TIE ROD NUT, PISTON (3/4-NF HEX) NUT,HEX 1/2 NC PL NUT HEX 7/16 NC PL BOLT NUT HEX 3/8 NC PL BREATHER,1/2 SQ HD CORED PLUG 1/2-14 NPT SEAL KIT 1 1/4 SEAL KIT,3 CROSS CYLINDER 1 1/16 2 3 4 7 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Note: This cylinder was used approx. through 1982. Always check length of barrel, type of stroke control, size and rod (Item #10), size of tie rods. (Item #16) before ordering parts. Replacement part # for complete assembly is 00759946 and the stroke control spacer kit is 00755234. This cylind FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 18 CYLINDER ASSEMBLY - CENTER AXLE S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 19 00759946 8354 163016 00760199 4675M 7339 00023100 00760661 00760194 00760200 4376 4690W 00760197 8754 00760196 00760202 00755234 00760199 2 2 1 1 1 1 1 1 1 1 8 1 1 1 4 1 CYLINDER 3 X 8 W/1-1/4 ROD PIN-HYD. CYLINDER PIN, COTTER 3/16 X 2 SEAL KIT (3 DIA HYD CYL) NUT PISTON BREATHER, CYLINDER HHCS 3/8 -16UNC 1-1/2 PL5 PISTON FOR 3BORE CYL TUBE, CYL 3X8 PISTON ROD NUT HEX 1/2-20 NF PL INSTALL SHEET-BELT TENSIONER&S HEAD, CYL 3 CLEVIS,OUTER BASE, CYL 3 ROD,CYL TIE (1/2NFX13)3X8 CYL CONTROL SPACER KIT SEAL KIT (3 DIA HYD CYL) REPLACEMENT PARTS ONLY Replacement cylinder not used in production. Used as replacement assembly. Parts WILL NOT interchange with earlier cylinder. Note: No screw on stroke control - use clip on spacers. (Item # 19) Seal Kit # 00760199 contains both old and new style piston seals. New style seal can be installed in old style piston. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 19 CYLINDER ASSEMBLY - CENTER AXLE S/N 01376 - 10429 JAN 1982 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 65113B1 651302 94514 0651130001 0651130005 0651130006 0651130007 00750208 0651130012 5B6240 7E62414 02816800 0651130016 0651130017 691351 8354 00000400 0651130022 0651130014 1 1 1 1 1 1 1 1 1 1 1 8 1 4 1 2 4 1 - CYLINDER HOSE #6 - 8 MP - 8 MP 180 LG ADAPTER, HYD, ELBOW SWIVEL CLEVIS BASE PISTON ROD BARREL PLUG,BREATHER 1/2 NPTM - 007 STROKE CONTROL NUT,ROD CLEVIS SHCS 3/8 NF 1-3/4 NUT 1/2 NF HEX HEAD 3 HYD CYL 1-1/4 ROD TIE ROD NUT PIN-HYD. CYLINDER PIN-COTTER 1/8 X 1-1/2 PLATED CLEVIS 1-14 NF THD SEAL KIT,3 LANTEX CYLINDER Note: This cylinder was used approx. after 1982. Always check length of barrel, and type of stroke control before ordering part. Replacement part # for complete cylinder assy is 00759946, and stroke control spacer kit is 00755234. Parts Will Not Interchange. This is an lantex cylinder length of barrel (Item #7) is 10 1/8" long. Stroke control (Item #9) is round with notches cast into it. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 20 CYLINDER ASSEMBLY - LEVEL LIFT - 2-1/2 X 8 SLAVE CYL S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 0652141500 0652141501 0652141312 0652141502 0652141503 0652141504 5JRC10180 0652140305 0652141506 0652140307 691356 37107B13 0652141311 691302 B651302 6513015 B65113A2 94514 1 1 1 1 1 1 4 1 1 2 4 2 1 1 1 1 6 CLY, LEVEL LIFT PISTON ROD PLUG, STRAIGHT ADAPTER TUBE HEAD PISTON NUT TOPLOCK 5/8 NF PLC TIEROD,HYD CYL W/NUT CLEVIS,BASE CLEVIS, ROD PIN CLIP-X HAIR PIN ADP HYD STGHT 8MB - 8FP HYD HOSE-3/8-8W/ 1/2 FITTING (NOT SHOWN) HOSE #6 - 8MP - 8MP - 180LG (NOT SHOWN) HOSE #6 - 8 MP - 8 MP 216 LG (NOT SHOWN) HYD HOSE ONE (NOT SHOWN) ADAPTER, HYD, ELBOW SWIVEL (NOT SHOWN) FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 21 CYLINDER ASSEMBLY - LEVEL LIFT - 2-3/4 X 8 SLAVE CYL S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 0652141400 0652141401 0652141312 0652141402 0652141403 0652141404 5JRC12100 0652140305 0652141406 0652140307 691356 37107B13 0652141311 691302 B651302 6513015 B65113A2 94514 1 1 1 1 1 1 4 1 1 2 4 2 1 1 1 1 6 HYD CYL KIT ROD,PISTON PLUG, STRAIGHT ADAPTER TUBE HYD CYL GLAND,ROD END PISTON NUT TOPLOCK 3/4 TIEROD,HYD CYL W/NUT CLEVIS,BASE CLEVIS, ROD PIN CLIP-X HAIR PIN ADP HYD STGHT 8MB - 8FP HYD HOSE-3/8-8W/(1/2FITTING (NOT SHOWN) HOSE #6 - 8MP - 8MP - 180LG (NOT SHOWN) HOSE #6 - 8 MP - 8 MP 216 LG (NOT SHOWN) HYD HOSE ONE (NOT SHOWN) ADAPTER, HYD, ELBOW SWIVEL (NOT SHOWN) FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 22 CYLINDER ASSEMBLY - LEVEL LIFT - 3 X 8 SLAVE CYL S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 0652141300 0652141301 0652141312 0652141302 0652141303 0652141304 6511320 0652140305 0652141306 0652140307 691356 37107B13 691302 B651302 6513015 B65113A2 94514 1 1 1 1 1 1 4 1 1 2 4 1 1 1 1 6 HYD CYL KIT PISTON ROD PLUG, STRAIGHT ADAPTER TUBE HEAD PISTON NUT, PISTON (3/4-NF HEX) TIEROD,HYD CYL W/NUT BASE CLEVIS CLEVIS, ROD PIN CLIP-X HAIR PIN HYD HOSE-3/8-8W/ 1/2FITTING (NOT SHOWN) HOSE #6 - 8MP - 8MP - 180LG (NOT SHOWN) HOSE #6 - 8 MP - 8 MP 216 LG (NOT SHOWN) HYD HOSE ONE (NOT SHOWN) ADAPTER, HYD, ELBOW SWIVEL (NOT SHOWN) Note; Center Cylinder has stroke control (Item 13) on shaft. The unit must already have hydraulic cylinders to fit arms and deck. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 23 CYLINDER ASSEMBLY - LEVEL LIFT REPLACEMENT ASSY (P/N 8719) S/N 00101 - 10429 OCT 1977 - MA ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 ?13 8719 8772 4705M 8768 8769 4706 8754 8773 4689 8774 8764 8354 163016 00755234 1 1 1 1 1 1 1 4 8 1 1 2 4 1 HYDRAULIC CYLINDER CAP PISTON NUT PISTON TUBE PISTON ROD CLEVIS,OUTER TIE ROD NUT HEX 9/16-18NF PL HEAD SEAL KIT PIN-HYD. CYLINDER PIN, COTTER 3/16 X 2 CONTROL SPACER KIT (NOT SHOWN.) Note: Center cylinder WILL NOT have screw on stroke control. The unit must already have hydraulic level left for these cylinders it mount to axle arms and deck. REPLACE CYL’S ONLY NOT USED IN PRODUCTION UNIT, PARTS WILL NOT INTERCHANE WITH EARLIER CYLINDERS. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 24 CYLINDER ASSEMBLY - LEVEL LIFT REPLACEMENT ASSY (P/N 8720) S/N 00101 - 10429 OCT 1977 - MA ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 8720 8778 4705 8775 8776 4706 8754 8773 4689 8779 8765 8354 163016 1 1 1 1 1 1 4 8 1 1 2 4 WING AXLE 3 1/4 X 8 SLAVE CYLINDER BASE CLEVIS PISTON NUT PISTON TUBE PISTON ROD ROD CLEVIS TIE ROD NUT 9/16 - 18 HEAD SEAL KIT PIN, CLEVIS COTTER PIN Note: Center cylinder WILL NOT have screw on stroke control. The unit must already have hydraulic level left for these cylinders it mount to axle arms and deck. REPLACE CYL’S ONLY NOT USED IN PRODUCTION UNIT, PARTS WILL NOT INTERCHANE WITH EARLIER CYLINDERS. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 25 CYLINDER ASSEMBLY - LEVEL LIFT REPLACEMENT ASSY (P/N 8721) S/N 00101 - 10429 OCT 1977 - MA ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 8721 8784 4675M 8780 8781 8753 8754 8785 4376 8786 8766 8354 163016 1 1 1 1 1 1 1 4 8 1 1 2 4 CYL HYD LEVEL LIFT 3 DIA CAP (HYD. CYLINDER) NUT PISTON PISTON TUBE PISTON ROD CLEVIS,OUTER TIE ROD NUT HEX 1/2-20 NF PL HEAD SEAL KIT PIN-HYD. CYLINDER PIN, COTTER 3/16 X 2 Note: Center cylinder WILL NOT have screw on stroke control. The unit must already have hydraulic level left for these cylinders it mount to axle arms and deck. REPLACE CYL’S ONLY NOT USED IN PRODUCTION UNIT, PARTS WILL NOT INTERCHANE WITH EARLIER CYLINDERS. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 26 CYLINDER ASSEMBLY - WING-HYDRAULIC CYLINDER & HOSE GROUP S/N 00101 - 01376 OCT 1977 - JAN ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 00759947 6513015 94514 691351 65130A12 65113B8 65130A4 65130A4 65130B15 651306 651307 691315 6511311 65113A12 0651130001 8354 00000400 65130A8 0651300003 6511320 00001200 5B7140 6511322 00013901 00750208 00749508 65113A30 6513011A 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 2 4 4 4 1 8 8 1 1 1 1 - CYLINDER 3 X 14 W/1-1/4 ROD HOSE #6 - 8 MP - 8 MP 216 LG ADAPTER, HYD, ELBOW SWIVEL NUT CLEVIS 1 1/8-12 NF THD HEAD 1 1/4 ROD 3 BR HEAD 3 BORE X 1-1/8 ROD HEAD 3 BORE X 1-1/8 ROD ROD,CYL 1-1/4 DIA,1-1/4-12 THD ROD TUBE OUTBOARD PISTON, 3, O RING SEAL PISTON, 3, UCUP SEAL CLEVIS BASE 1/2 CLEVIS BASE 7/16 PIN-HYD. CYLINDER PIN-COTTER 1/8 X 1-1/2 PLATED TIE ROD 1/2 X 19 ROD NUT, PISTON (3/4-NF HEX) NUT,HEX 1/2 NC PL NUT 7/16 NC HEX BOLT NUT HEX 3/8 NC PL PLUG,BREATHER 1/2 NPTM - 007 PLUG 1/2-14 NPT SEAL KIT 3 CR CYL, 1 1/4 SEAL KIT,3 CROSS CYLINDER 1 1/8 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Note: This cylinder used throught approx 1982. Check length of barrel before ordering replacement pars. If the cylinder was used check size of tie rods (Item #12) and size of cylinder rod (Item #6). REPLACEMENT PARTS FOR THIS COMPLETE CYLINDER ASSY IS 00759947. PARTS WILL NOT INTERCHANGE. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 27 CYLINDER ASSEMBLY - WING-LANTEX HYDRAULIC CYL & HOSE GRP S/N 01377 - 10429 JAN 1982 - MAY ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 65130B1 6513015 94514 0651130001 0651130005 0651300001 0651300002 5B6240 7E62414 0651130022 02816800 0651130016 0651300003 691351 8354 00000400 00750208 0651130014 1 1 1 1 1 1 1 1 1 1 8 1 4 1 2 4 1 - HYD. CYL. 3" BORE X 14" STROKE 1-1/4" DIA. ROD BASE END HOSE #6 - 8 MP - 8 MP 216 LG ADAPTER, HYD, ELBOW SWIVEL CLEVIS BASE PISTON ROD TUBE NUT,ROD CLEVIS SHCS 3/8 NF 1-3/4 CLEVIS 1-14 NF THD NUT 1/2 NF HEX HEAD 3 HYD CYL 1-1/4 ROD ROD NUT PIN-HYD. CYLINDER PIN-COTTER 1/8 X 1-1/2 PLATED PLUG,BREATHER 1/2 NPTM - 007 SEAL KIT,3 LANTEX CYLINDER Note: This cylinder used approx. After 1982 always check barrel lenght (Item #7) before ordering replacement parts. REPLACE THIS CYLINDER ASSY WITH #00759947. PARTS WILL NOT INTERCHANGE. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 28 CYLINDER ASSEMBLY - WING-REPLACEMENT S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 5 6 7 8 9 10 11 12 13 14 15 16 17 18 ?19 00759947 00756496 94517 7329 94507 00760196 00760198 00760201 00760195 00013901 00023100 8754 4690W 00760197 00760203 4675M 8354 162012 6511324 00760199 1 1 1 1 1 1 1 1 1 1 1 1 8 1 4 1 2 2 1 CYLINDER 3 X 14 W/1-1/4 ROD HOSE-#4-6MP-6MP-216LG ADAPTER, HYD, ELBOW SWIVEL ADAPTER, HYD, STGHT RESTRICTOR ADAPTER, HYD, REDUCER BASE, CYL 3 PISTON ROD, CYL 3X14 TUBE, CYL 3X14 NUT HEX 3/8 NC PL HHCS 3/8 -16UNC 1-1/2 PL5 CLEVIS,OUTER INSTALL SHEET-BELT TENSIONER&S HEAD, CYL 3 TIE ROD, CYL 3X14 NUT PISTON PIN-HYD. CYLINDER PIN,COTTER BREATHER,1/2 SQ HD CORED SEAL KIT (3 DIA HYD CYL) Note: This is a replcaement cylinder and was not used in production. PARTS WILL NOT INTERCHANGE WITH EARLIER CYLINDERS. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 29 DECALS S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 5 6 7 8 9 10 11 12 13 14 15 16 17 18 21 23 24 D303 D301 D337 D121 D122 999200 D112 D103 D102 D101A D137 99203 D138 D131 D304 NFS 999403 00756494 99204 999401 26E127001 26E127004 26E127000 3 1 3 1 1 1 1 1 1 4 1 2 1 1 2 1 1 3 1 2 A/R A/R A/R DECAL,RHINO DECAL,RHINO DECAL-FLX-S-15 DECAL ADJ-NUTS DECAL(PREV. STREAKNG) DECAL GENERAL WARNING ALL UNIT DECAL USE SAE GER LUB DECAL,OPERATE AT 540 RPM DECAL PTO SFT TO HTCH DECAL OIL LEVEL DECAL CCW BLADE ROTATION DECAL, RED REFLECTOR DECAL-CW BLADE ROTATION DECAL NOTICE DECAL (RHINO) SERIAL NUMBER PLATE DECAL-DANGER, OFFSET WGT. BOX DECAL-DANGER,DRIVELINE DECAL-YELLOW REFLECTOR DECAL, ROTATING BLADE PAINT,1 QT,RH ORANGE PAINT, 1 GAL,RH ORNG PAINT,(SPRAY)RHINO ORANGE FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 30 DEFLECTOR - REAR WING S/N 01497 - 10429 JUN 1982 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 6 7 8 13 00002700 00001800 00756876 02030700 10 10 2 7 FLATWASHER 1/2 PL STD LOCKNUT TLM 1/2 NC PLB WING REAR COVER HHCS 1/2-13UNC 1-1/4 PL5 FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 31 DEFLECTOR - RUBBER FRONT CENTER S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 00758370 00758261 00758263 02030700 00001800 1 1 1 3 3 DEFLECTOR, ASY, FRT CTR BAND RUBBER GD FRT CTR PANEL RUBBER GD FRT CTR HHCS 1/2-13UNC 1-1/4 PL5 LOCKNUT TLM 1/2 NC PLB Note: These will not fit earlier serial numbers. Complete of deflectors front-center, left and right wings assembly #00758355. For 10 foot unit order assembly #00756994. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 32 DEFLECTOR - RUBBER FRONT WING LEFT & RIGHT S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 00758368 00758264 00758259 02030700 00001800 1 1 1 7 7 DEFLECTOR ASSEMBLY PANEL BAND HEX BOLT LOCKNUT FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 33 DEFLECTOR - RUBBER LEFT & RIGHT CENTER S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 00758369 00758262 00758260 02030700 00001800 1 1 1 2 2 DEFLECTOR, ASY, FRT L-R CTR PANEL RUBBER GD L&R CTR BAND, RUBBER GD LH & RH HHCS 1/2-13UNC 1-1/4 PL5 LOCKNUT TLM 1/2 NC PLB Note: These will not fit earlier serial numbers. Complete of deflectors front-center, left and right wings assembly #00758355. For 10 foot unit order assembly #00756994. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 34 DRIVELINE ASSEMBLY - CTR GEARBOX SQUARE SHAFT SLIP 35R S/N 00101 - 10429 OCT 1977 - MAY 19 ITEM PART NO. QTY. DESCRIPTION 1 0657070000 W707LSA W341 W324 9C482010 5B8200 W318 W284A W3071 271105B 7AH551816 5JRC5180 W279R W324A 1 1 1 1 1 1 1 1 1 1 4 4 2 1 DRIVELINE, SLIP ASSY CTR D/L,S15, SHAFT SQ YOKE 1 3/16 SQ HOLE PAINT BLK SHSS 1/2 NF 1-1/4 NUT 1/2 NF HEX YOKE W/TAPERED SHAFT PAINT BLK YOKE,SLIDE COLLAR PAINT BLACK YOKE, TORQUE LIMITER (7-1/16 BUSHING SP & TL YOKE HEXB 5/16NC 2 NUT TOPLOCK 5/16 CROSS REPAIR KIT, CTR YOKE,1-3/16 SQ HOLE W/SETSCREW 2 3 4 5 6 7 8 9 10 11 12 FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 35 DRIVELINE ASSEMBLY - OUTBOARD SQUARE SHAFT ASSEMBLY 35R S/N 00101 - 10429 OCT 1977 - MAY 1 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 W705RB7 W316B W3071 271105B W279R 7AH551816 5JRC5180 W702RZ4 W702RZ W312Z W318 W284A 17C1981 1 1 1 1 1 4 4 1 1 1 1 1 1 SHFT, SHLD,SM TL YK YK & SHFT ASSY 39-1/8 YOKE, TORQUE LIMITER (7-1/16 BUSHING SP & TL YOKE CROSS REPAIR KIT, CTR HEXB 5/16NC 2 NUT TOPLOCK 5/16 HSG, SHLD,TPR YOKE HSG, SHLD,QD YOKE YOKE TB & SLV 50 YOKE W/TAPERED SHAFT PAINT BLK YOKE,SLIDE COLLAR PAINT BLACK GREASE ZERK 9 10 11 FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 36 DRIVELINE ASSEMBLY - PTO SQUARE SHAFT ASSEMBLY 44R S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 W805O4 W805O11 W816A W826 W827A W840 W802B W812A W821A W44B2A W44B3 W44B4A 17C1981 1 1 1 1 1 1 1 1 1 1 1 1 1 SHFT, SHLD,TPR YK PAINT BLACK SHAFT 44R SQ ASY 1-3/4-20 SPL YOKE SHAFT PAINT BLACK YOKE,SAE TAPER PAINT BLACK YOKE,CLP,1-3/4-20SP PAINT BLK CROSS REPR KIT HSG,SHLD,QD YK PAINT BLACK YOKE SLEEVE PAINT BLACK YOKE,Q.D. 6BSPLN PAINT BLACK QD REPAIR KIT SPRING-PIN LOCK WASHER X GREASE ZERK 2 3 4 5 6 7 8 9 10 11 FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 37 DRIVELINE ASSEMBLY - SHIELDING ASSEMBLY SQUARE SHAFTS S/N 00101 - 10429 OCT 1977 - MAY 198 ITEM PART NO. QTY. DESCRIPTION 1 W811Q W815R W315RA1 W311RZ1 W335 00751176 W936 W937 AR AR AR AR AR AR AR AR SHIELD D/L OUTER PAINT BLACK SHLD IN ASSY PAINT BLACK SHIELD ASSY, INNER SHIELD, OUTER BEARING, NYLON RETAINER, NYLON BRG. WASHER THRUST RING SNAP 2 4 5 6 7 FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 38 NOTES FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 39 GEARBOX ASSEMBLY - CENTER SECTION S/N 00101 - 10429 OCT 1977 - MAY 1988 FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 40 GEARBOX ASSEMBLY - CENTER SECTION S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 7010414 00748532 00752155 7010416 701047R 00752159 00748527 00748525 00753738 00753737 00748522 701044R 00749509 00748519 7010422 00748526 701046R 00758647 7010419 00758648 00011400 02030700 7AH5121620 00011700 00753743 00748547 00748539 5E16140 00606000 00565000 00749508 5312316 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 2 1 A/R A/R 1 8 4 4 8 4 1 4 1 1 1 2 4 HOUSING MAIN HOUSING-BEARING CAP CAP BEARING RETAINING SHAFT, INPUT 1-3/8-6 OUTPUT SHAFT & GEAR GEAR BEVEL-22 TOOTH BEARING CONE TIMKEN #LM603049 BEARING CUP BEARING CONE 16137 BEARING CUP 16282 BEARING CONE BEARING CUP 363 SEAL OIL SEAL RING RING, RETAINING SPACER SHIM, ADJUSTMENT .010 OR .25M SHIM KIT SHIM ,ADJUSTMENT O.5 HHCS 3/8 NC 1 PL5 HHCS 1/2-13UNC 1-1/4 PL5 C/S 3/4 X 2 1/2 NF 5 LOCKWASHER 5/16 PL STD LOCKWASHER FLATWASHER 1-1/32 X 2-3/16X.22 NUT TOPLOCK 3/4 NF PLB NUT CASTLE 1 -14 STD PL PIN-COTTER 3/16 X 2 PLUG, HEX HEAD PIPE 1/8-27NPT PLUG 1/2-14 NPT WASHER (SPECIAL) NOTE: ITEM 15,23,27, & 32 NOT INCLUDED WITH GEARBOX ASSEMBLY AND MUST BE SPECIFIED WHEN ORDERING 701041 GEARBOX ASSEMBLY. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 41 GEARBOX ASSEMBLY - DIVIDER (COMER) S/N 01901 - 10429 FEB 1985 - MAY 1988 FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 42 GEARBOX ASSEMBLY - DIVIDER (COMER) S/N 01901 - 10429 FEB 1985 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 19 21 22 0656030000 00753232 00753240 00753233 00753221 00753234 00753228 00753223 00755070 00753238 00753225 00753237 00753237 00753239 00753226 00753230 00753231 00755069 00753222 00753235 00753227 1 1 1 2 1 2 4 2 2 2 2 2 1 2 6 6 1 2 2 2 DIVIDER GEARBOX CASING COVER SHAFT SHAFT CROWNWHEEL BEVEL PINION BEARING BEARING OIL SEAL OIL SEAL INTERNAL CIRCLIP INTERNAL CIRCLIP OIL FILLER PLUG PLUG HEXB METRIC 8-P1.25- 30MM PL5 SCHNORR WASHER GASKET SHIM SHIM TAKE-UP RING NOTE: ITEMS 30 AND 31 ARE NOT FURNISHED WITH THE GEARBOX ASSEMBLY. THIS GEARBOX HAS 1 3/8 TAPER SHAFTS. P/N 651033 GEAR REPLACE BY P/N 00757028. Offest units used gearbox#0651030000 (same as #65103 except only on wing out put shaft) Cover #0682053, 6 bolts #0682053, 6 bolts #7A10118, &6 lockwashers #131000. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 43 GEARBOX ASSEMBLY - DIVIDER S/N 00101 - 01900 OCT 1977 - FEB 1985 FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 44 GEARBOX ASSEMBLY - DIVIDER S/N 00101 - 01900 OCT 1977 - FEB 1985 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 65103 16212012 5312315 5312316 651035 651037 7A1101110 00757028 651031 5312312 PT204A 531232 651036 W84 W83 PT103 271096 5312310 PT104 PT105 531237 531238 PT209 5310415 651034 00001300 00750959 301021 651032 00751003 00010300 00752658 5DR12160 D112 D101A 4 3 4 1 1 18 3 1 3 3 2 2 3 3 2 2 4 2 2 3 3 3 2 1 8 8 1 1 1 6 6 1 1 1 GEARBOX ASSY COTTER PIN CASTE NUT (SPECIAL THIN) SPECIAL WASHER (HEAT TREATED) INPUT SHAFT BEARING CARRIER CAP PLACE BOLT BEVEL GEAR, 18-TEETH PRIMARY GEAR BOX HOUSING SHIM SET GASKET DRIVE SHAFT HOUSING OUTPUT SHAFT BEARING CUP BEARING CONE OIL SEAL BEARING COLLAR KEY (HEAT TREATED) LOCKNUT LOCKWASHER BEARING CUP BEARING CONE WOODRUFF KEY OIL SEAL GASKET LOCKWASHER CAPSCREW BREATHER PLUG GEAR BOX COVER PLATE PIPE PLUG LOCKWASHER CAPSCREW NUT DECAL (USE SAE GEAR LUBE) DECAL (OIL LEVEL) FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 45 GEARBOX ASSEMBLY - LEFT WING S/N 00101 - 10429 OCT 1977 - MAY 1988 FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 46 GEARBOX ASSEMBLY - LEFT WING S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 22 24 25 26 28 29 30 0656230000 00563900 00564300 711052 0656230001 00564000 00564600 00564800 00563700 00757682 00564400 00563600 00612703 00564500 00564100 00563500 00564200 00565000 00749508 00011400 00753642 7AH5101816 W67 00011700 00748547 5E16140 00606000 00749136 1 1 1 1 1 1 1 3 1 A/R 1 2 1 3 1 1 1 1 6 4 4 4 10 1 1 1 4 GEARBOX MAIN HOUSING CAP, BEARING CAP W/SPACER SHAFT,1-3/8-6 INPUT W/PILOT PINION OUTPUT SHAFT INPUT GEAR BEARING,BALL BEARING, BALL SPACER, BEARING SHIM GASKET SNAP-RETAINER RING RING,RETAINING RING, RETAINING SEAL, OIL OUTPUT OIL SEAL PLUG, HEX HEAD PIPE 1/8-27NPT PLUG 1/2-14 NPT HHCS 3/8 NC 1 PL5 HHCS,3/8NC X 1-1/4,ZP,GRD5 C/S 5/8 X 2 NF GR5 WASHER LOCKWASHER 5/16 PL STD FLATWASHER 1-1/32 X 2-3/16X.22 NUT CASTLE 1 -14 STD PL PIN-COTTER 3/16 X 2 NUT TOPLOCK 5/8 NF PLB IMPORTANT NOTE: Item #3 and Item #9 must be replaced together at the same time, do not change one without the other. If #711052 or #6710510 is ordered a cup and spacer will be shipped together as a kit so order one # or the other, not both. ITEMS 12,22,24,29, AND 30 ARE NOT FURNISHED WITH GEARBOX ASSEMBLY AND MUST BE SPECIFIED, IF REQUIRED. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 47 GEARBOX ASSEMBLY - RIGHT WING S/N 00101 - 10429 OCT 1977 - MAY 1988 FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 48 GEARBOX ASSEMBLY - RIGHT WING S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 22 23 24 25 26 28 29 30 0656220000 0656220001 0656220003 00757683 0656220002 00564000 00564600 00564800 00563700 00757682 00564400 00563600 00612703 00564500 00564100 00563500 00564200 00565000 00749508 00011400 00753642 7AH5101816 00751003 W67 00011700 00768547 5E16140 00606000 00749136 1 1 1 1 1 1 1 3 1 A/R 1 2 1 3 1 1 1 1 6 4 4 1 4 10 1 1 1 4 GEARBOX HOUSING CAP CAP, OUTPUT SHAFT PINION OUTPUT SHAFT INPUT GEAR BEARING,BALL BEARING, BALL SPACER, BEARING SHIM GASKET SNAP-RETAINER RING RING,RETAINING RING, RETAINING SEAL, OIL OUTPUT OIL SEAL PLUG, HEX HEAD PIPE 1/8-27NPT PLUG 1/2-14 NPT HHCS 3/8 NC 1 PL5 HHCS,3/8NC X 1-1/4,ZP,GRD5 C/S 5/8 X 2 NF GR5 PIPE PLUG 1/4 NPTM STANDARD WASHER LOCKWASHER 5/16 PL STD DECAL - PC2040 NUT CASTLE 1 -14 STD PL PIN-COTTER 3/16 X 2 NUT TOPLOCK 5/8 NF PLB IMPORTANT NOTE: Item #3 and Item #9 must be replaced together at the same time, do not change one without the other. If #711052 or #6710510 is ordered a cup and spacer will be shipped together as a kit so order one # or the other, not both. ITEMS 12,22,24,29, AND 30 ARE NOT FURNISHED WITH GEARBOX ASSEMBLY AND MUST BE SPECIFIED, IF REQUIRED. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 49 GEARBOX ATTACHMENT - DIVIDER & CENTER GEARBOX S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 0651470000 0656130100 0656520000 1 1 1 SHIELD ASSEMBLY SHIELD, PRIMARY GEARBOX CTR GEAR BOX SHIELD 2 FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 50 GEARBOX ATTACHMENT- RIGHT & LEFT WING GEARBOX S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 0656451210 0656451110 1 1 SHIELD WLD SHIELD WLD FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 51 HOSE BRACKET COMPONENTS S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 0651140100 0651150100 02675800 00010400 00010300 1 1 2 2 2 WLDMT, HYD. HOSE BRKT HYD. HOSE BRKT. HHCS 5/8-11UNC 1-1/2 PL5 NUT 5/8 NC HEX PL LOCKWASHER 5/8 PL STD FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 52 HUB ASSEMBLY - CENTER & OUTBOARD S/N 10148 - 10428 JAN 1988 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 3 4 5 6 7 8 9 10 11 12 13 14 15 00757241 00756576 00750434 00756577 00752177 00750614 00756490 00750616 00756493 00756492 00026200 00003500 00756489 0371242102 1 1 4 5 5 1 1 1 1 1 1 1 1 WHEEL HUB, PREASSY BEARING CUP OUTSIDE BEARING CONE INSIDE BEARING CUP INSIDE BOLT, STUD 1/2-20 NF X 1-7/8 NUT 1/2-20NF 90DEG.CONE LUG PL NUT SLOTTED THIN 1 NF PLC OIL SEAL WASHER DUST CAP PIN-COTTER 5/32 X 1-1/2 ZERK FITTING 1/8 STRAIGHT HUB W/ CUPS & STUBS BEARING CONE Note: This hub was used on all center and outboard, standard, level lift axles between these serial numbers. this hub has no washer behind seal on spindle and logo cast into backside of hub. When using sectional tires install item #7 flat against wheel, opposite picture. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 53 HUB ASSEMBLY - OUTBOARD AXLES S/N 00101 - 10147 OCT 1977 - JAN 1988 ITEM PART NO. QTY. DESCRIPTION 3 4 5 6 7 8 9 10 11 12 13 14 15 271033 PT108 00006500 00016900 13198 00750614 5DR12160 00771458 15B1200 PT112 1621/2010 00003500 PT110SA PT109 1 1 1 5 5 1 1 1 1 1 1 1 1 HUB GROUP ASSY BEARING CUP BEARING CONE BEARING CUP BOLT, HUB NUT 1/2-20NF 90DEG.CONE LUG PL NUT 3/4 NF SLOTTED OIL SEAL WASHER 3/4 P SAE HUB CAP CTR ZERK FITTING 1/8 STRAIGHT WHEEL HUB BEARING CONE Note: When using sectional tires install item #7 flat against wheel, opposite picture. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 54 HUB ASSEMBLY - STANDARD CENTER AXLE S/N 00101 - 10147 OCT 1977 - JAN 1988 ITEM PART NO. QTY. DESCRIPTION 3 4 5 6 7 8 9 10 11 12 13 14 15 371247 00016900 371247E 371247D 13198 00750614 371247J 371247F 371247H 371247H 1621/2012 00003500 371247SA 371247C 1 1 1 5 5 1 1 1 1 1 1 1 1 HUB, ASY BEARING CUP BEARING CONE 342A BEARING CUP 332 BOLT, HUB NUT 1/2-20NF 90DEG.CONE LUG PL NUT, 7/8-14 UNF STD SLOTTED SEAL WASHER WASHER PINS-CTR 5/32 X 1 1/2 ZERK FITTING 1/8 STRAIGHT HUB BEARING CONE Note: Spindel will have washer welded to it behind seal. When using sectional tires install item #7 flat against wheel, opposite picture. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 55 HYDRAULIC CONTROL VALVE MOUNTING KIT S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 651401 00016200 13500 5B5180 1 6 6 6 MT BKT WLD HHCS 5/16NC 2 PL5 L WSHR 5/16 NUT 5/16 NC HEX FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 56 HYDRAULIC HOSE ADAPTERS S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 2 4 5 00275400 651311 651312 3 3 3 Q.D, COUPLER #8 QD COUPLER HALF FEMALE COUPLER HALF, MALE Note: Choice of couplers is up to the customer. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 57 HYDRAULIC VALVE ASSEMBLY - DETENT W/SPRING ASSEMBLY S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 18 19 20 21 22 23 24 25 26 27 28 29 30 6514016 6514017 6514018 6514019 6514020 6514021 7E42012 6514022 7D42014 6514023 6514024 6514025 65140A54 1 1 1 1 1 1 1 1 4 1 1 1 1 HOUSING DETENT SLEEVE WASHER SPRING CENTERING (25#) COLLAR STEP WASHER C/S1/4 X 1 1/2 SK HD CAP,END BOLT BALL 1/4 STEEL SPRING PLUG WASHER Standard quantities for one Detent Assembly 3 required per hydraulic valve. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 58 HYDRAULIC VALVE ASSEMBLY - OPEN/CLOSED CENTER VALVE S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 19E13/41/2 65140A47 65140A48 7E4204 65140A46 6514012 6514013 6514026 6514027 6514028 6514029 6514030 6514031 65140A50 6514042 6514039 6514037 2 3 3 6 3 6 6 3 3 3 3 3 3 1 1 1 1 PIPE BUSHING HANDLE KIT-PIN SHCS 1/4 NC 1/2 BRKT PLATE RETAINER SEAL, O-RING POPPET SPRING,LIFT CHECK SEAL, O-RING PLUG PLATE,1/16 ORIFICE RETAINER NON -ADJUSTABLE RELIEF ASSEMBLY (OPEN CENTER ONLY) CLOSED CENTER ASSEMBLY (CLOSED CENTER ONLY) CONVERSION PLUG ASSEMBLY NO-RELIEF ASSEMBLY (CLOSED CENTER ONLY) FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 59 JACK ASSEMBLY - TOP WING S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 0811140000 00749892 00751685 651081W 7A101116 131000 5B10110 1 1 1 1 2 2 2 PARKING JACK PIN-JACK RETAINING PIN-CLIP HAIR BKTS PARKING JACK BLT 5/8 X 2 ZP LOCK WASHER NUT 5/8 HEX, ZP FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 60 LEFT SCREW S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 ?7 0656510000 651062F 00609200 02030300 00760135 00756579 0656510001 1 2 2 2 1 1 1 MANUAL-LIFT SCREW FITTING,GREASE (DRIVE TYPE) HEXB 1 NC 4 GR5 NUT TOPLOCK 1 NC PLB HANDLE,MANUAL LIFT SCREW TOP LINK THREAD LOCK MANUAL-LIFT SCREW FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 61 LEVEL LIFT KIT FIELD INSTALLATION S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 0652140120 0652140130 0652140140 0652140150 371063A 0652140160 691154 5GR12100 7AH5101132 02956948 15B1600 163016 65107A3C 0652150100 0652150000 1 1 1 1 1 1 1 1 2 2 1 1 1 1 WLDMT, BASE WLDMT, PIVOT ARM WLDMT, SPRING ROD SPRING GUIDE SPRING PIN PIN LOCKNUT TLM 3/4 NC PL C/S 5/8 X 4 NC GR.5 LOCKNUT 5/8 NC PLC WASHER 1 SAE P PIN, COTTER 3/16 X 2 WASHER AXLE LUG ASSEMBLY LEVEL LIFT KIT FS15 Note: Factory level lift did not use bracket #14 on axle arms. Axle arms had longer lugs on them. To order complete field installation level lift kit, including hydraulic cylinders and hoses, order bundle #0652150000. (Most current type cylinder used will be used shipped) FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 62 LEVEL LIFT ROD ASSEMBLY S/N 10148 - 10428 JAN 1988 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 584042 651101 00770485A 651102 5C1490 00606000 15B1200 2 2 2 4 2 8 8 WLDMT-ROD CONTROL ROD NUT,EXTENDED ADJUSTMENT PIN-DRILLED HEXNUT 7/8 JAM ZP PIN-COTTER 3/16 X 2 WASHER 3/4 P SAE FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 63 MAINFRAME ASSEMBLY S/N 00101 - 01900 OCT 1977 - FEB 1985 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 0656011000 0656020200 0656020100 65109 20A4012E 5710121 5F5180 0656270000 0656261000 0656260000 1 1 1 2 2 3 6 2 2 2 WLDMT, FS15 CTR SECT M.FF L/H O/B FRAME WLD R/H O/B FRAME WLD PIN HINGE PIN COVER PLATE NUT 5/16 NC WING T,SPACER,LONG SPACER,SHORT HINGE SPACER,SHORT Note: Later models replaced lock pin w/bolts and nut. Part number 7A51812 bolt, 5GR5180 locknut. PART NUMBER 0656261000 REPLACES PART NUMBER 0656260000 FOR SERIAL # 00631 AND ON. PART NUMBER 0656261000, 21-5/8" LONG. PART #0656260000, 171/4" LONG. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 64 MAINFRAME ASSEMBLY S/N 01901 - 10429 FEB 1985 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 0656011000 0656020200 0656020100 65109 20A4012E 5710121 5F5180 0656270000 0656261000 0656260000 1 1 1 2 2 3 6 2 2 2 WLDMT, FS15 CTR SECT M.FF L/H O/B FRAME WLD R/H O/B FRAME WLD PIN HINGE PIN COVER PLATE NUT 5/16 NC WING T,SPACER,LONG SPACER,SHORT HINGE SPACER Note: Later models replaced lock pin w/bolts and nut. Part number 7A51812 bolt, 5GR5180 locknut. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 65 SKID SHOE & SIDE SKIRT - OFFSET MODELS CTR SECTION S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 652071 65203L 2A381312 00001200 00001300 281316 00748823 1 1 3 8 8 3 2 SIDESKIRT WLDMT, LEFT SIDE SHOES SLIDE BOLT,PLOW 1/2 NC X 1-1/2 GR.5 NUT,HEX 1/2 NC PL LOCKWASHER 1/2 PL STD CARB 1/2NC X 2 HHCS 1/2-13UNC 1-1/2 PL5 FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 66 SKID SHOE & SIDE SKIRT S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 65202RW 65202LW 65203R 65203L 15B800 00001200 7A81312 13800 2A381312 D303 D337 1 1 1 1 12 18 12 18 6 2 2 SKIRT SIDE SKIRT SIDE SHOES SLIDE SHOES SLIDE WASHER 1/2 SAE ZP NUT,HEX 1/2 NC PL C/S1/2 X 1 1/2 NC LOCK WASHER BOLT,PLOW 1/2 NC X 1-1/2 GR.5 DECAL,RHINO DECAL-FLX-S-15 Note: This side skirt is 1/4" thick. Replace old 3/16" Thick side skirt with out modification. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 67 SKID SHOE ASSEMBLY S/N 00101 - 00466 OCT 1977 - FEB 1979 ITEM PART NO. QTY. DESCRIPTION 1 0656490010 0656490020 2A381312 00001200 13800 00013300 15B800 0656490107 1 1 2 5 5 3 2 1 ASY,RIGHT SKID SHOE ASY,LEFT SKID SHOE BOLT,PLOW 1/2 NC X 1-1/2 GR.5 NUT,HEX 1/2 NC PL LOCK WASHER HEXB 1/2 NC 2 PL5 WASHER 1/2 SAE ZP WEAR PLATE 2 3 4 5 6 7 Note: Later Models have item 1 welded to center section of the mainframe at assembly. These can be used to replace skid shoe mount broken off on units FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 68 SKID SHOE ASSEMBLY S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 0656490107 2A381312 00001200 13800 1 2 2 2 WEAR PLATE BOLT,PLOW 1/2 NC X 1-1/2 GR.5 NUT,HEX 1/2 NC PL LOCK WASHER FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 69 SPRING ASSEMBLY - CENTER AXLE S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 0656460110 0656460120 5JRC12100 371063A 65107A4 00002701 02023800 37107B13 0656460240 1 1 4 4 4 4 4 2 2 UPPER SPRING WLD LOWER SPRING WLD NUT TOPLOCK 3/4 SPRING GUIDE SPRING FLATWASHER,3/4,TYPE AW,ZP HEXB 3/4 NC 6-1/2PL CLIP-X HAIR PIN WLDMT-PIN Note: Center Spring Assembly was optional eqpt. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 70 SPRING ASSEMBLY - WING S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 0656460200 0656460220 0656460210 37107B13 0656460230 65107A4 371063A 00037200 02023800 0656460240 00002701 1 1 2 1 1 1 1 1 1 1 OUTBOARD SPRING ASSY ROCKER ARM WLD SPRING BASE WLD CLIP-X HAIR PIN PIN-WLD GUIDE SPRING SPRING NUT TOPLOCK 3/4 NC PLC HEXB 3/4 NC 6-1/2PL WLDMT-PIN FLATWASHER,3/4,TYPE AW,ZP Note: These sere not used on units with hyd level lift. See level lift section for spring assy’s used FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 71 TIRE/WHEEL ASSEMBLY S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 1 2 00008700 00019200 00025200 00749700 1 1 1 WHEEL, 15 X 5.00 DC (RIM ONLY) WHEEL 14 X 5.00 DC (RIM ONLY) LAMINATED PUNCTURE-PROOF TIRE & WHEEL ASSEMBLY (21" OD) 6.00 X 9 14" AIRPLANE TIRE AND WHEEL ALSO AVAILABLE Used 14" Airplane Tire and Wheel - P/N 00749700 (not shown) FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 72 TONGUE ASSEMBLY S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 B65105 651051 0656050200 651052 0656050300 651053 651054 7AH5121620 00752161 7AH5121636 00748539 00606000 1 1 1 1 1 1 2 2 1 6 3 2 TONGUE WLDMT, TONGUE WLDMT, TONGUE HITCH, FS15 PART CLEVIS, TONGUE TNG-HITCH CONT ROD ROD HITCH CONTROL PIN-TONGUE PIVOT C/S 3/4 X 2 1/2 NF 5 HHCS 3/4 NF 3 PL5 C/S 3/4 X 4 1/2 NF 5 NUT TOPLOCK 3/4 NF PLB PIN-COTTER 3/16 X 2 2 3 4 5 6 7 8 Note: Item #6 has ears cast on to it. Check before ordering. Item #5 bronze bushing FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 73 TORQUE LIMITER ASSEMBLY S/N 00101 - 10001 OCT 1977 - AUG 1987 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 70105 701052 00748832 00748833 701054R 00748825 701055R 00748831 701053R 9C16163 00748834 1 1 2 1 1 1 4 1 1 1 TORQUE LIMITER ASSY DRIVE PLATE PLATE,PRESSURE DISC,CLUTCH HUB, TORQUE LIMITER BUSHING NUT ADJ TOPLOCK SPRING, BELLEVILLE PLUG BRONZE SHSS CUP POINT 3/8NC X 3/8 PL BACK PLATE Note: Item #7 is hex shaped nut. Check before ordering. Notice: Most Parts are interchangeable with the Warner-Motive Torque Limiter (70105). To prevent damage to the assembly, do not use or mix 0731070006 spring together with 701056 spring on the sam assemly. Also, replacement of the disc and spring with Warner parts will lower the capacity of the FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 74 TORQUE LIMITER ASSEMBLY S/N 10001 - 10429 AUG 1987 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 0731070000 00748829 00748834 0731070003 0731070004 0731070005 0731070006 0731070007 1 1 2 1 1 3 1 TORQUE-LIMITER 3SPG HUB BACK PLATE DISK, FRICTION PLATE,DRIVE PLATE, PRESSURE SPRING, BELLVILLE NUT, ADJUSTING FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 75 WEIGHT BOX S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 0656390100 0656390300 12BF6168 00012101 00757359 7A121016 00003901 00000200 15B1200 20A4012E 1 1 6 6 1 1 1 1 1 1 WEIGHT BOX WELD COVER SCREW 3/8 X 1 NC LOCKWASHER 3/8 PL HVY BRACE STRAP C/S 3/4 X 2 NC ZP LOCKWASHER 3/4 PL HEAVY NUT 3/4 NC HEX PL WASHER 3/4 P SAE PIN FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 76 WINCH AND STAND ASSSEMBLY S/N 00101 - 10429 OCT 1977 - MAY 1988 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 0656200100 00011400 00748823 15B600 00012101 00001300 00013901 00001200 B651202 651202 651203 65111 37107B13 1 3 2 1 3 2 3 2 1 1 1 1 2 STAND WINCH FS15 HHCS 3/8 NC 1 PL5 HHCS 1/2-13UNC 1-1/2 PL5 WASHER 3/8 SAE P LOCKWASHER 3/8 PL HVY LOCKWASHER 1/2 PL STD NUT HEX 3/8 NC PL NUT,HEX 1/2 NC PL WINCH & CABLE WINCH CABLE, 1/4 AIRCRAFT W/THIMBLE BAR, TRANSPORT CLIP-X HAIR PIN Note: this winch will fit and work in place of all previous winches with no modifications. FS15 Master Parts Book (July-05) ©2005 Alamo Group Inc. Parts Section – 77 SERVIS-RHINO LIMITED WARRANTY 1. LIMITED WARRANTIES 1.01.Servis-Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”) that the goods purchased are free from defects in material or workmanship. 1.02.Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship. 1.03.This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found in your Operator’s Manual. 1.04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer. 2. REMEDIES AND PROCEDURES. 2.01.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days of purchase. 2.02.Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the claim is based. 2.03.Purchaser is responsible for returning the goods in question to the Dealer. 2.04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will: (a) Repair or replace the defective goods or part(s) or (b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer. The choice of remedy shall belong to Manufacturer. 2.05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the Dealer to the designated factory. 3. LIMITATION OF LIABILITY. 3.01.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 3.02.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS. 3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER’S LIABILITY HEREUNDER FOR DAMAGES INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS. 3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED. 4. MISCELLANEOUS. 4.01.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas. 4.02.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term. 4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein. 4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein. KEEP FOR YOUR RECORDS ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification when applying for warranty. Servis-Rhino Implement Model _______________________________ Serial Number ________________________________ Date Purchased __________________________________________ Dealer ______________________________________ ATTENTION: READ YOUR OPERATOR'S MANUAL RHINO® 1020 S. Sangamon Ave. Gibson City, IL 60936 800-446-5158 Email: parts@servis-rhino.com TO THE OWNER/OPERATOR/DEALER To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER: 1. 2. 3. 4. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and Ensure that each employee uses such Seatbelt while the tractor is moving; and Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected area provided by the ROPS. REQUIRED OF THE OPERATOR 1. 2. 3. 4. 5. 6. 7. 8. 9. Securely fasten seatbelt if the tractor has a ROPS. Where possible, avoid operating the tractor near ditches, embankments, and holes. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces. Stay off slopes too steep for safe operation. Watch where you are going - especially at row ends, on roads, and around trees. Do not permit others to ride. Operate the tractor smoothly - no jerky turns, starts, or stops. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer. When the tractor is stopped, set brakes securely and use park lock, if available. Keep children away from danger all day, every day... Equip tractors with rollover protection (ROPS) and keep all machinery guards in place... Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens. FS15 PL 07-05 Printed U.S.A. P/N 00773425MB
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Page Count : 84 Page Mode : UseOutlines Page Layout : OneColumn Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-14, framework 1.6 About : uuid:194d5571-e5ed-43e7-8d67-67aba09d27a4 Producer : Acrobat Distiller 6.0.1 (Windows) Creator Tool : PageMaker 6.5 Modify Date : 2005:08:22 10:40:36-05:00 Create Date : 2005:08:03 08:52:17-05:00 Metadata Date : 2005:08:22 10:40:36-05:00 Document ID : uuid:7cfc6fb7-4dfe-4cc8-bf88-63a1df2d371b Format : application/pdf Title : FS15,FS10 COVER.p65 Creator : sftrinidad Author : sftrinidadEXIF Metadata provided by EXIF.tools