Servis Rhino Rotary Mower Se4 Users Manual 1348 1548 1948 PUB 05 04 COVERS
SE4 to the manual 3139a157-8515-4c0a-b077-6020aa336b15
2015-02-02
: Servis-Rhino Servis-Rhino-Rotary-Mower-Se4-Users-Manual-490822 servis-rhino-rotary-mower-se4-users-manual-490822 servis-rhino pdf
Open the PDF directly: View PDF .
Page Count: 21
Download | |
Open PDF In Browser | View PDF |
SE4 ROTARY MOWER Rev 09-05 S/N 16874 -Current Part No.00760866P PART'S MANUAL An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or Servis-Rhino (800-446-5158) to obtain a Free copy before operating the equipment. RHINO® 1020 S. Sangamon Ave. Gibson City, IL 60936 800-446-5158 Email: parts@servis-rhino.com © 2005 Alamo Group Inc. TO THE OWNER/OPERATOR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death. PARTS SECTION Parts Section – 1 PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. NOTE: Please refer to The Safety Section in the front of this Manual for the proper Part Number when ordering Replacement Safety Decals. For maximum safety and to guarantee optimum product reliability, always use genuine Servis-Rhino Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to: RHINO ® 1020 S. Sangamon Ave. Gibson City, IL 60936 800-446-5158 Email: parts@servis-rhino.com ©2005 Alamo Group Inc. Parts Section – 2 PART NAME INDEX DRIVELINE ASSEMBLY S/N 16873 -BELOW Rev 10-04 ..................................................................................................... 8 DRIVELINE ASSEMBLY S/N 16874 -CURRENT Rev 09-05 .............................................................................................. 10 FRONT DEFLECTORS ASSEMBLY.................................................................................................................................... 11 GEARBOX ASSEMBLY.......................................................................................................................................................... 6 HYDRAULIC RELIEF ASSEMBLY (OPTION)...................................................................................................................... 13 MAIN ASSEMBLY................................................................................................................................................................... 4 OFFSET ADAPTER (OPTION) ............................................................................................................................................ 14 REAR DEFLECTORS ASSEMBLY ...................................................................................................................................... 12 SAFETY DECAL SHEETS ................................................................................................................................................... 15 SE4 (Oct-04) S/N 16874 -Current Rev 09-05 ©2007 Alamo Group Inc. Parts Section – 3 MAIN ASSEMBLY SE4 (Oct-04) S/N 16874 -Current Rev 09-05 ©2007 Alamo Group Inc. Parts Section – 4 MAIN ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 00773753 00770773 00770772 00757949R 00770781 00766542 00603500 00770777 00766505 00773564 00755881 00766610 00761655P 00762365 02957510 00768968 02963669 00036900 15B2000 00773768 00773565R 00773566 9143009 00761402 00773812 00761535 00750226 00766590R 00606000 00758692 7192 02958784 00773755R 00762423 00772590 00766611 00770066 001465 00772588 03101646 00773567 00766086 00772291 02958788 1 1 1 4 1 2 4 2 2 5 1 1 2 1 9 2 1 1 1 1 1 1 2 2 2 2 1 1 1 1 2 1 2 1 1 1 1 1 2 1 1 2 4 MAIN ASSEMBLY LOCKNUT BOLT BAR TOP LINK BOLT BUSHING HITCH PIN (CAT 1) LOCKNUT A-FRAME BAR REAR BRACE LOCKNUT MOUNTING FLAT GEARBOX BOLT BOLT LOCKNUT BOLT COTTER PIN WASHER TAILWHEEL BEAM CASTER FORK SPINDLE LOCKNUT BLADE BOLT SUCTION BLADE WASHER LOCKNUT DISHPAN COTTER PIN SLOTTED NUT SNAP RING BOLT MAIN FRAME WASHER SHIELD BRACKET GAUGE WHEEL MOUNT CABLE & PINS ASSY GREASE FITTING SHIELD PLATE LOCKWASHER TIRE RIM ASSEMBLY FLATWASHER HITCH LUG BOLT SE4 (Oct-04) S/N 16874 -Current Rev 09-05 ©2007 Alamo Group Inc. Parts Section – 5 GEARBOX ASSEMBLY SE4 (Oct-04) S/N 16874 -Current Rev 09-05 ©2007 Alamo Group Inc. Parts Section – 6 GEARBOX ASSEMBLY ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 17 18 19 20 21 22 23 PART NO. QTY. DESCRIPTION 00761655 00564700 00564200 00563700 00564300 00564400 00752481 00564100 00563900 00564800 00752480 00757682 00760928 00760929 02161100 00011400 00563500 00606000 7202 6192 00757683 7A81324 7192 00001800 00765444 1 1 3 1 AR 1 3 1 1 1 1 AR AR 10 10 1 1 1 1 1 1 1 1 1qt GEARBOX ASSY INPUT SHAFT SEAL BALL BEARING INPUT CAP GASKET INPUT GEAR RETAINING RING HOUSING BEARING OUTPUT PINION & SHAFT BEARING SPACER GASKET .25 GASKET .10 LOCKWASHER BOLT SEAL COTTER PIN SLOTTED NUT WASHER OUTPUT CAP BOLT RETAINING RING LOCKNUT QT,ALAMO 000 GEAR LUBE SE4 (Oct-04) S/N 16874 -Current Rev 09-05 ©2007 Alamo Group Inc. Parts Section – 7 DRIVELINE ASSEMBLY S/N 16873 -BELOW Rev 10-04 SE4 (Oct-04) S/N 16874 -Current Rev 09-05 ©2007 Alamo Group Inc. Parts Section – 8 DRIVELINE ASSEMBLY S/N 16873 -BELOW Rev 10-04 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 00759161B 00768296 001465 00768257 00756231 00768295 00768294 00768293 00770391 00759170 00764506 00754330 00764507 00775112 00775113 1 1 1 2 1 1 1 1 1 1 6 1 1 1 DRIVELINE ASSEMBLY INNER SHAFT & SHIELD ASSY GREASE FITTING SHEAR BOTL YOKE CROSS & BEARING KIT INNER TUBE ASSEMBLY OUTER SHAFT & SHIELD ASSY OUTER TUBE ASSEMBLY TWIST COLLAR KIT YOKE ASSEMBLY INNER TUBE BEARING LOCKING PIN OUTER TUBE BEARING INNER HALF SHIELD ASSEMBLY OUTER HALF SHIELD ASSEMBLY SE4 (Oct-04) S/N 16874 -Current Rev 09-05 ©2007 Alamo Group Inc. Parts Section – 9 DRIVELINE ASSEMBLY S/N 16874 -CURRENT Rev 09-05 ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 00759161C 00764500A 00756231 ---------------00759169 ------------------------------00759165 ---------------00777329A 00764506 00754330 00764507 00768342 ------------------------------------------------------------00768294 00768296 ------------------------------00774079 1 2 1 1 1 1 1 1 1 1 6 1 1 1 1 1 1 1 1 1 1 1 DRIVELINE ASY,YOKE COLLAR - COMPLETE CROSS & BEARING KIT SERIES 40 OUTER YOKE PIN ROLL 8mm X 60mm OUTER TUBE WITH LABEL INNER TUBE PIN ROLL INNER TUBE INNER YOKE YOKE, 1-3/8 BORE SP COLLAR-INNER-GUARD-RETAINER BOLT, NYLON - SAFETY SHIELD] COLLAR-OUTER-GUARD-RETAINER SHIELD, ASY, CMPLT FEMALE TUBE YOKE WITH LABEL MALE TUBE YOKE HALF FEMALE GUARD HALF FEMALE GUARD SHAFT, ASY, OUTER W/SHIELD SHAFT, ASY, INNER W/SHIELD DANGER LABEL FOR OUTER TUBE DANGER LABEL FOR OUTER GUARD TUBE KIT,SLIDE COLLAR REPAIR SE4 (Oct-04) S/N 16874 -Current Rev 09-05 ©2007 Alamo Group Inc. Parts Section – 10 FRONT DEFLECTORS ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 00773940 00001800 00748823 00773944 00773943 6 6 1 1 FRONT DEFLECTOR ASSY LOCKNUT BOLT DEFLECTOR STRAP DEFLECTOR SE4 (Oct-04) S/N 16874 -Current Rev 09-05 ©2007 Alamo Group Inc. Parts Section – 11 REAR DEFLECTORS ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 00761603 00761597 00761596 00761598 00761599 7A181310 00001800 2 2 1 1 6 6 REAR DEFLECTOR ASSY SIDE STRAP SIDE DEFLECTOR CENTER DEFLECTOR CENTER STRAP BOLT LOCKNUT SE4 (Oct-04) S/N 16874 -Current Rev 09-05 ©2007 Alamo Group Inc. Parts Section – 12 HYDRAULIC RELIEF ASSEMBLY (OPTION) ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 8709 8708 02845500 00695100 2 2 2 2 CHAIN ASSEMBLY BRACKET BOLT NUT SE4 (Oct-04) S/N 16874 -Current Rev 09-05 ©2007 Alamo Group Inc. Parts Section – 13 OFFSET ADAPTER (OPTION) ITEM PART NO. QTY. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 0702310000 0702310100 0702310001 0702310300 0702310200 511027 7A14924 15B1400 423013 5JRC1490 3W6 02030400 00001300 00001200 7AH5121636 595062 00748539 7AH5101816 00749136 743013 1 1 1 1 2 2 4 4 2 2 4 4 4 1 1 1 2 2 2 OFFSET ADAPTER ADAPTER MAINFRAME BRACE BAR BRACE LUG AND CHAIN ADJUSTABLE LIFT LUG WRIST PIN BOLT WASHER BUSHING LOCKNUT RETAING PIN BOLT LOCKWASHER HEX NUT BOLT SPACER LOCKNUT BOLT LOCKNUT BUSHING SE4 (Oct-04) S/N 16874 -Current Rev 09-05 ©2007 Alamo Group Inc. Parts Section – 14 SAFETY DECAL SHEETS ITEM PART NO. QTY. DESCRIPTION 1 2 3 00776481 00773310 2738332 1 1 2 SHEET,MANUALCANISTER DECAL KIT, DECAL SHEET SE-4 DECAL, RED OBLONG REFLECTOR (NOT SHOWN) SE4 (Oct-04) S/N 16874 -Current Rev 09-05 ©2007 Alamo Group Inc. Parts Section – 15 SERVIS-RHINO LIMITED WARRANTY 1. LIMITED WARRANTIES 1.01.Servis-Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”) that the goods purchased are free from defects in material or workmanship. 1.02.Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship. 1.03.This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found in your Operator’s Manual. 1.04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer. 2. REMEDIES AND PROCEDURES. 2.01.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days of purchase. 2.02.Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the claim is based. 2.03.Purchaser is responsible for returning the goods in question to the Dealer. 2.04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will: (a) Repair or replace the defective goods or part(s) or (b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer. The choice of remedy shall belong to Manufacturer. 2.05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the Dealer to the designated factory. 3. LIMITATION OF LIABILITY. 3.01.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 3.02.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS. 3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER’S LIABILITY HEREUNDER FOR DAMAGES INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS. 3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED. 4. MISCELLANEOUS. 4.01.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas. 4.02.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term. 4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein. 4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein. KEEP FOR YOUR RECORDS ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification when applying for warranty. Servis-Rhino Implement Model _______________________________ Serial Number ________________________________ Date Purchased __________________________________________ Dealer ______________________________________ ATTENTION: READ YOUR OPERATOR'S MANUAL RHINO® 1020 S. Sangamon Ave. Gibson City, IL 60936 800-446-5158 Email: parts@servis-rhino.com R TO THE OWNER/OPERATOR/DEALER To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER: 1. 2. 3. 4. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and Ensure that each employee uses such Seatbelt while the tractor is moving; and Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected area provided by the ROPS. REQUIRED OF THE OPERATOR 1. 2. 3. 4. 5. 6. 7. 8. 9. Securely fasten seatbelt if the tractor has a ROPS. Where possible, avoid operating the tractor near ditches, embankments, and holes. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces. Stay off slopes too steep for safe operation. Watch where you are going - especially at row ends, on roads, and around trees. Do not permit others to ride. Operate the tractor smoothly - no jerky turns, starts, or stops. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer. When the tractor is stopped, set brakes securely and use park lock, if available. Keep children away from danger all day, every day... Equip tractors with rollover protection (ROPS) and keep all machinery guards in place... Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens. SE4 PL 10/04 Printed U.S.A. P/N 00760866P
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Modify, Copy, Annotate, Fill forms, Extract, Assemble, Print high-res XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Producer : Acrobat Distiller 5.0.5 (Windows) Keywords : Create Date : 2005:09:26 19:45:46Z Modify Date : 2007:08:30 13:34:19-05:00 Metadata Date : 2007:08:30 13:34:19-05:00 Creator Tool : Adobe PageMaker 7.0 Format : application/pdf Creator : egallegos Title : 1348 1548 1948 PUB 05-04 COVERS Description : 1348 1548 1948 PUB 05-04 COVERS Document ID : uuid:fe1316a5-3931-4534-9137-6bae72c4d529 Instance ID : uuid:59c1c69b-3527-4f62-8bc0-afd969985c7f Page Count : 21 Subject : 1348 1548 1948 PUB 05-04 COVERS Author : egallegosEXIF Metadata provided by EXIF.tools