Servis Rhino Rotary Mower Se4 Users Manual 1348 1548 1948 PUB 05 04 COVERS

SE4 to the manual 3139a157-8515-4c0a-b077-6020aa336b15

2015-02-02

: Servis-Rhino Servis-Rhino-Rotary-Mower-Se4-Users-Manual-490822 servis-rhino-rotary-mower-se4-users-manual-490822 servis-rhino pdf

Open the PDF directly: View PDF .
Page Count: 21

RHINO®

1020 S. Sangamon Ave.

Gibson City, IL 60936

800-446-5158

Email: parts@servis-rhino.com

PART'S MANUAL

An Operator's Manual was shipped with the equipment in the

Manual Canister. This Operator's Manual is an integral part of

the safe operation of this machine and must be maintained

with the unit at all times. READ, UNDERSTAND, and FOLLOW

the Safety and Operation Instructions contained in this manual

before operating the equipment. If the Operator's Manual is

not with the equipment, contact your dealer or Servis-Rhino

(800-446-5158) to obtain a Free copy before operating the

equipment.

SE4

ROTARY MOWER

Rev 09-05 S/N 16874 -Current Part No.00760866P

TO THE OWNER/OPERATOR/DEALER

All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who

recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to

be used with all its safety equipment properly attached to minimize the chance of accidents.

BEFORE YOU START!! Read the safety messages on the implement and shown in your manual.

Observe the rules of safety and common sense!

WARRANTY INFORMATION:

Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form

in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card

and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic

failure with possible injury or death.

PARTS

SECTION

Parts Section – 1

Parts Section – 2

For maximum safety and to guarantee optimum product reliability, always use

genuine Servis-Rhino Parts. The use of inferior replacement parts may cause

premature or catastrophic failure which could result in serious injury or death.

Direct any questions regarding parts to:

The following instructions are offered to help eliminate needless delay and error in processing

purchase orders for the equipment in this section.

1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the

basic machine featured in this manual. Part Numbers and Descriptions are given to help

locate the parts and quantities required.

2. The Purchase Order must include the name and address of the person or organization

ordering the parts, who should be charged, and if possible, the serial number of the machine

for which the parts are ordered.

3. The Purchase Order must clearly list the quantity of each part, the complete and correct part

number (be sure to include all periods), and the basic name of the part.

4. The Manufacturer reserves the right to substitute parts where applicable.

5. Some parts are unlisted items which are special production items not normally stocked and

are subject to special handling. Request a quotation for such parts before sending a

Purchase Order.

6. The Manufacturer reserves the right to change prices without prior notice.

NOTE: Please refer to The Safety Section in the front of this Manual for the proper

Part Number when ordering Replacement Safety Decals.

PARTS ORDERING GUIDE

RHINO®

1020 S. Sangamon Ave.

Gibson City, IL 60936

800-446-5158

Email: parts@servis-rhino.com

PART NAME INDEX

DRIVELINE ASSEMBLY S/N 16873 -BELOW Rev 10-04..................................................................................................... 8

DRIVELINE ASSEMBLY S/N 16874 -CURRENT Rev 09-05 .............................................................................................. 10

FRONT DEFLECTORS ASSEMBLY.................................................................................................................................... 11

GEARBOX ASSEMBLY.......................................................................................................................................................... 6

HYDRAULIC RELIEF ASSEMBLY (OPTION)...................................................................................................................... 13

MAIN ASSEMBLY................................................................................................................................................................... 4

OFFSET ADAPTER (OPTION) ............................................................................................................................................ 14

REAR DEFLECTORS ASSEMBLY ...................................................................................................................................... 12

SAFETY DECAL SHEETS ................................................................................................................................................... 15

SE4 (Oct-04) S/N 16874 -Current Rev 09-05

MAIN ASSEMBLY

SE4 (Oct-04) S/N 16874 -Current Rev 09-05

MAIN ASSEMBLY

ITEM PART NO. QTY. DESCRIPTION

00773753 - MAIN ASSEMBLY

1 00770773 1 LOCKNUT

2 00770772 1 BOLT

3 00757949R 1 BAR TOP LINK

4 00770781 4 BOLT

5 00766542 1 BUSHING

6 00603500 2 HITCH PIN (CAT 1)

7 00770777 4 LOCKNUT

8 00766505 2 A-FRAME BAR

9 00773564 2 REAR BRACE

10 00755881 5 LOCKNUT

11 00766610 1 MOUNTING FLAT

12 00761655P 1 GEARBOX

13 00762365 2 BOLT

14 02957510 1 BOLT

15 00768968 9 LOCKNUT

16 02963669 2 BOLT

17 00036900 1 COTTER PIN

18 15B2000 1 WASHER

19 00773768 1 TAILWHEEL BEAM

20 00773565R 1 CASTER FORK

21 00773566 1 SPINDLE

22 9143009 1 LOCKNUT

23 00761402 2 BLADE BOLT

24 00773812 2 SUCTION BLADE

25 00761535 2 WASHER

26 00750226 2 LOCKNUT

27 00766590R 1 DISHPAN

28 00606000 1 COTTER PIN

29 00758692 1 SLOTTED NUT

30 7192 1 SNAP RING

31 02958784 2 BOLT

32 00773755R 1 MAIN FRAME

33 00762423 2 WASHER

34 00772590 1 SHIELD BRACKET

35 00766611 1 GAUGE WHEEL MOUNT

36 00770066 1 CABLE & PINS ASSY

37 001465 1 GREASE FITTING

38 00772588 1 SHIELD PLATE

39 03101646 2 LOCKWASHER

40 00773567 1 TIRE RIM ASSEMBLY

41 00766086 1 FLATWASHER

42 00772291 2 HITCH LUG

43 02958788 4 BOLT

SE4 (Oct-04) S/N 16874 -Current Rev 09-05

GEARBOX ASSEMBLY

SE4 (Oct-04) S/N 16874 -Current Rev 09-05

GEARBOX ASSEMBLY

ITEM PART NO. QTY. DESCRIPTION

00761655 - GEARBOX ASSY

1 00564700 1 INPUT SHAFT

2 00564200 1 SEAL

3 00563700 3 BALL BEARING

4 00564300 1 INPUT CAP

5 00564400 AR GASKET

6 00752481 1 INPUT GEAR

7 00564100 3 RETAINING RING

8 00563900 1 HOUSING

9 00564800 1 BEARING

10 00752480 1 OUTPUT PINION & SHAFT

11 00757682 1 BEARING SPACER

12 00760928 AR GASKET .25

00760929 AR GASKET .10

13 02161100 10 LOCKWASHER

14 00011400 10 BOLT

15 00563500 1 SEAL

17 00606000 1 COTTER PIN

18 7202 1 SLOTTED NUT

19 6192 1 WASHER

20 00757683 1 OUTPUT CAP

21 7A81324 1 BOLT

22 7192 1 RETAINING RING

23 00001800 1 LOCKNUT

00765444 1qt QT,ALAMO 000 GEAR LUBE

SE4 (Oct-04) S/N 16874 -Current Rev 09-05

DRIVELINE ASSEMBLY S/N 16873 -BELOW Rev 10-04

SE4 (Oct-04) S/N 16874 -Current Rev 09-05

DRIVELINE ASSEMBLY S/N 16873 -BELOW Rev 10-04

ITEM PART NO. QTY. DESCRIPTION

00759161B - DRIVELINE ASSEMBLY

1 00768296 1 INNER SHAFT & SHIELD ASSY

2 001465 1 GREASE FITTING

3 00768257 1 SHEAR BOTL YOKE

4 00756231 2 CROSS & BEARING KIT

5 00768295 1 INNER TUBE ASSEMBLY

6 00768294 1 OUTER SHAFT & SHIELD ASSY

7 00768293 1 OUTER TUBE ASSEMBLY

8 00770391 1 TWIST COLLAR KIT

9 00759170 1 YOKE ASSEMBLY

10 00764506 1 INNER TUBE BEARING

11 00754330 6 LOCKING PIN

12 00764507 1 OUTER TUBE BEARING

13 00775112 1 INNER HALF SHIELD ASSEMBLY

14 00775113 1 OUTER HALF SHIELD ASSEMBLY

SE4 (Oct-04) S/N 16874 -Current Rev 09-05

DRIVELINE ASSEMBLY S/N 16874 -CURRENT Rev 09-05

ITEM PART NO. QTY. DESCRIPTION

00759161C - DRIVELINE

1 00764500A 1 ASY,YOKE COLLAR - COMPLETE

2 00756231 2 CROSS & BEARING KIT SERIES 40

3 ---------------- 1 OUTER YOKE

4 00759169 1 PIN ROLL 8mm X 60mm

5 ---------------- 1 OUTER TUBE WITH LABEL

6 ---------------- 1 INNER TUBE

7 00759165 1 PIN ROLL INNER TUBE

8 ---------------- 1 INNER YOKE

9 00777329A 1 YOKE, 1-3/8 BORE SP

10 00764506 1 COLLAR-INNER-GUARD-RETAINER

11 00754330 6 BOLT, NYLON - SAFETY SHIELD]

12 00764507 1 COLLAR-OUTER-GUARD-RETAINER

13 00768342 1 SHIELD, ASY, CMPLT

14 ---------------- 1 FEMALE TUBE YOKE WITH LABEL

15 ---------------- 1 MALE TUBE YOKE

16 ---------------- 1 HALF FEMALE GUARD

17 ---------------- 1 HALF FEMALE GUARD

18 00768294 1 SHAFT, ASY, OUTER W/SHIELD

19 00768296 1 SHAFT, ASY, INNER W/SHIELD

20 ---------------- 1 DANGER LABEL FOR OUTER TUBE

21 ---------------- 1 DANGER LABEL FOR OUTER GUARD TUBE

22 00774079 1 KIT,SLIDE COLLAR REPAIR

SE4 (Oct-04) S/N 16874 -Current Rev 09-05

FRONT DEFLECTORS ASSEMBLY

ITEM PART NO. QTY. DESCRIPTION

00773940 - FRONT DEFLECTOR ASSY

1 00001800 6 LOCKNUT

2 00748823 6 BOLT

3 00773944 1 DEFLECTOR STRAP

4 00773943 1 DEFLECTOR

SE4 (Oct-04) S/N 16874 -Current Rev 09-05

REAR DEFLECTORS ASSEMBLY

ITEM PART NO. QTY. DESCRIPTION

00761603 - REAR DEFLECTOR ASSY

1 00761597 2 SIDE STRAP

2 00761596 2 SIDE DEFLECTOR

3 00761598 1 CENTER DEFLECTOR

4 00761599 1 CENTER STRAP

5 7A181310 6 BOLT

6 00001800 6 LOCKNUT

SE4 (Oct-04) S/N 16874 -Current Rev 09-05

HYDRAULIC RELIEF ASSEMBLY (OPTION)

ITEM PART NO. QTY. DESCRIPTION

1 8709 2 CHAIN ASSEMBLY

2 8708 2 BRACKET

3 02845500 2 BOLT

4 00695100 2 NUT

SE4 (Oct-04) S/N 16874 -Current Rev 09-05

OFFSET ADAPTER (OPTION)

ITEM PART NO. QTY. DESCRIPTION

0702310000 - OFFSET ADAPTER

1 0702310100 1 ADAPTER MAINFRAME

2 0702310001 1 BRACE BAR

3 0702310300 1 BRACE LUG AND CHAIN

4 0702310200 1 ADJUSTABLE LIFT LUG

5 511027 2 WRIST PIN

6 7A14924 2 BOLT

7 15B1400 4 WASHER

8 423013 4 BUSHING

9 5JRC1490 2 LOCKNUT

10 3W6 2 RETAING PIN

11 02030400 4 BOLT

12 00001300 4 LOCKWASHER

13 00001200 4 HEX NUT

14 7AH5121636 1 BOLT

15 595062 1 SPACER

16 00748539 1 LOCKNUT

17 7AH5101816 2 BOLT

18 00749136 2 LOCKNUT

19 743013 2 BUSHING

SE4 (Oct-04) S/N 16874 -Current Rev 09-05

SAFETY DECAL SHEETS

ITEM PART NO. QTY. DESCRIPTION

1 00776481 1 SHEET,MANUALCANISTER DECAL

2 00773310 1 KIT, DECAL SHEET SE-4

3 2738332 2 DECAL, RED OBLONG REFLECTOR (NOT SHOWN)

SE4 (Oct-04) S/N 16874 -Current Rev 09-05

LIMITED WARRANTY

1. LIMITED WARRANTIES

1.01.Servis-Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal

purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”)

that the goods purchased are free from defects in material or workmanship.

1.02.Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be

defective under normal use and service due to defects in material or workmanship.

1.03.This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use,

negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or

lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal

combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found

in your Operator’s Manual.

1.04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any

nature on behalf of Manufacturer.

2. REMEDIES AND PROCEDURES.

2.01.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer

within 30 days of purchase.

2.02.Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the

goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the

claim is based.

2.03.Purchaser is responsible for returning the goods in question to the Dealer.

2.04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and

service due to defects in material or workmanship, Manufacturer will:

(a) Repair or replace the defective goods or part(s) or

(b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer)

if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty

by Manufacturer.

The choice of remedy shall belong to Manufacturer.

2.05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and

for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the trans-

portation cost for the goods or part(s) from the Dealer to the designated factory.

3. LIMITATION OF LIABILITY.

3.01.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES

WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE.

3.02.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR

USE OF THE GOODS.

3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO

PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE

CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT

LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM

THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE

ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER’S LIABILITY HEREUNDER FOR DAMAGES

INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS.

3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER

THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS

OCCURRED.

4. MISCELLANEOUS.

4.01.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County,

Texas.

4.02.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall

be deemed to be a waiver of any other term.

4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the

invalidity of such provision shall not invalidate any other provisions herein.

4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein.

KEEP FOR YOUR RECORDS

ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine

identification when applying for warranty.

Servis-Rhino Implement Model _______________________________ Serial Number ________________________________

Date Purchased __________________________________________ Dealer ______________________________________

ATTENTION:

READ YOUR OPERATOR'S MANUAL

SERVIS-RHINO

1020 S. Sangamon Ave.

Gibson City, IL 60936

800-446-5158

Email: parts@servis-rhino.com

RHINO®

TO THE OWNER/OPERATOR/DEALER

To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and

the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily

find the information you need.

The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety

requirements of tractor operators:

REQUIRED OF THE OWNER:

1. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and

2. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and

3. Ensure that each employee uses such Seatbelt while the tractor is moving; and

4. Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected

area provided by the ROPS.

REQUIRED OF THE OPERATOR

1. Securely fasten seatbelt if the tractor has a ROPS.

2. Where possible, avoid operating the tractor near ditches, embankments, and holes.

3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.

4. Stay off slopes too steep for safe operation.

5. Watch where you are going - especially at row ends, on roads, and around trees.

6. Do not permit others to ride.

7. Operate the tractor smoothly - no jerky turns, starts, or stops.

8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer.

9. When the tractor is stopped, set brakes securely and use park lock, if available.

Keep children away from danger all day, every day...

Equip tractors with rollover protection (ROPS) and keep all machinery

guards in place...

Please work, drive, play and live each day with care and concern for

your safety and that of your family and fellow citizens.

Printed U.S.A. P/N 00760866PSE4 PL 10/04

Servis Rhino Rotary Mower Se4 Users Manual 1348 1548 1948 PUB 05 04 COVERS

SE4 to the manual 3139a157-8515-4c0a-b077-6020aa336b15

Navigation menu

Versions of this User Manual:

Views

Navigation