Shark Professional Steam Pocket Mop S3601Co Users Manual
Sharp-S3601Co-Users-Manual-804896 sharp-s3601co-users-manual-804896
2015-03-30
: Shark Shark-Shark-Professional-Steam-Pocket-Mop-S3601Co-Users-Manual-678910 shark-shark-professional-steam-pocket-mop-s3601co-users-manual-678910 shark pdf
Open the PDF directly: View PDF .
Page Count: 20
Download | |
Open PDF In Browser | View PDF |
WWW.SHARKCLEAN.COM PRO STEAM POCKET® MOP S3601CO N OWNER’S GUIDE S3601CO_N_11_IB_E_130304_4.indd 1 13-03-04 2:53 PM IMPORTANT SAFETY INSTRUCTIONS For Household Use Only WHEN USING YOUR SHARK® STEAM MOP, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: WARNING: READ ALL INSTRUCTIONS BEFORE USING YOUR STEAM MOP. 2. DO NOT use outdoors. DANGER OF SCALDING. Please use caution when using the steam mop. The steam emitted from the steam mop is very hot. POLARIZED PLUG: This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature. TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY: 1. Use the system only for its intended use. 3. DO NOT leave the appliance unattended when plugged in. Always unplug the power cord from the electrical outlet when not in use and before servicing. 4. DO NOT allow to be sued as a toy. DO NOT allow the appliance to be used by children. Close attention is necessary when used by or near children, pets or plants. 5. Use only as described in this manual. 6. Use only manufacturer’s recommended accessories. 7. DO NOT operate this appliance if it is not working as it should, with a damaged plug or cord, if the unit has been dropped, damaged, left outdoors, or dropped in water. To avoid the risk of fire, do not disassemble or attempt to repair the appliance on your own. Return the appliance to EURO-PRO Operating LLC for examination and repair. Incorrect re-assembly or repair can cause a risk of electrical shock or injury to persons when the appliance is used. 8. To protect against a risk of electric shock, DO NOT immerse the steam mop into water or any other liquids. 9. DO NOT handle plug or steam mop with wet hands or operate appliance without shoes. 2 TOLL FREE: 1-800-798-7398 S3601CO_N_11_IB_E_130304_4.indd 2 13-03-04 2:53 PM 10. DO NOT pull or carry by power cord, use power cord as handle, close a door on the power cord, or pull the power cord around sharp edges or corners. Keep power cord away from heated surfaces. 20. When cleaning the steam mop, unplug the power cord from the electrical outlet and clean with a dry or damp cloth. Do not pour water or use alcohol, benzene or paint thinner on the unit. 11. DO NOT unplug by pulling on power cord. To unplug, grasp the plug not the power cord. Do not use extension cords or outlets with inadequate current carrying capacity. 21. Extreme caution should be exercised when using this appliance to clean stairs. 12. DO NOT put any objects into openings. Do not use with any opening that is blocked. 13. DO NOT put hands or feet under the steam mop. Unit gets very hot. 14. Use ONLY on flat, horizontal surfaces. Do not use on walls, counters or windows. 15. DO NOT use on leather, wax polished furniture or floors, synthetic fabrics, velvet or other delicate, steam sensitive materials. 16. DO NOT add cleaning solutions, scented perfumes, oils or any other chemicals to the water used in this appliance as this may damage the unit or make it unsafe for use. If you live in a hard water area, we recommend using distilled water in your steam mop. 17. When in use, NEVER turn the appliance over or on its side. NEVER DIRECT STEAM TOWARDS PEOPLE, ANIMALS OR PLANTS. 18. NEVER LEAVE THE STEAM MOP IN ONE SPOT ON ANY SURFACE FOR ANY PERIOD OF TIME WHEN THE CLEANING PAD IS ATTACHED AS THIS WILL DAMAGE YOUR FLOORS. 19. Carefully remove the cleaning pad immediately after you have unplugged and allowed the steam mop to cool. 22. Never use steam mop without the cleaning pad attached. 23. Keep your work area well lit. 24. Store steam mop indoors in a cool, dry place. 25. To avoid circuit overload, do not operate another appliance on the same socket (circuit) as the steam cleaner. 26. DO NOT run appliance over the power cord. If an extension cord is absolutely necessary, an extension cord rated a minimum of 15 ampere, 14 gage cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange cord so that it cannot be pulled or tripped over. 27 Always unplug and allow the steam mop to cool before removing or changing mop heads. WARNING: Your steam mop is designed to clean hard floor surfaces that will withstand high heat. Do not use on unsealed wood or unglazed ceramic floors. On surfaces that have been treated with wax or some no wax floors, the sheen may be removed by the heat and steam action. It is always recommended to test an isolated area of the surface to be cleaned before proceeding. We also recommend that you check the use and care instructions from the floor manufacturer. SAVE THESE INSTRUCTIONS www.sharkclean.com S3601CO_N_11_IB_E_130304_4.indd 3 3 13-03-04 2:53 PM This manual covers model number: S3601CO N 11 TECHNICAL SPECIFICATIONS Voltage: 120V., 60Hz. Power: 1550 Watts Water Capacity: 500ml (16.9 oz.) Euro-Pro, Shark and Navigator are trademarks of Euro-Pro Operating LLC. All other brand names may be trademarks of their respective owners. TOLL FREE: 1-800-798-7398 S3601CO_N_11_IB_E_130304_4.indd 4 13-03-04 2:53 PM Contents Thank you for purchasing the Shark® Pro Steam Pocket® Mop. Getting Started.......................................................................2 Using Your Steam Mop........................................................5 Using Your Carpet Glider....................................................9 Care of Your Steam Mop.....................................................10 Troubleshooting Guide........................................................12 Warranty....................................................................................15 www.sharkclean.com S3601CO_N_11_IB_E_130304_4.indd 1 1 13-03-04 2:53 PM Getting Started When assembling your steam mop there may be a little water in or around the water tank. This is because we test all our steam mops 100% before you buy them, so you get a quality Shark® Pro Steam Pocket® Mop. h i a c b j l k d m e f g a All-Purpose Mop Head (1), XL Mop Head (1) and Triangle Mop Head (1) b Steam Mop Body h Quick Release Swivel Cord Wrap i Cord Clips j Water Tank Cap c Mop Handle k Water Tank d Two-Sided Cleaning Pads for the All-Purpose Mop Head (2), XL Mop Head (1) and Triangle Mop Head (1) l ON/Standby Switch e (1) 6mm x 54mm Large Screw* *Phillips or flat head screwdriver can be used. Screwdriver not included. f Filling Flask m Mop Head Release Button g Carpet Glider 2 TOLL FREE: 1-800-798-7398 S3601CO_N_11_IB_E_130304_4.indd 2 13-03-04 2:53 PM fig. 1 IMPORTANT: First things first, always make sure the mop is UNPLUGGED from the wall when not in use. Never fill the mop, attach the mop head, change or remove the cleaning pad when the mop is plugged into the wall. To prolong the life of your Shark ® Pro Steam Pocket® Mop, we recommend using distilled water. Make sure you only add water to the tank. Chemicals or cleaning solution may damage the appliance and could be unsafe for you and your family. ASSEMBLE 1 Insert the Mop handle end labeled “Front” into the steam mop body. Make sure it is inserted past the line printed on the pole. Secure the assembled handle and pole by using the large screw and a Phillips or a flat head screwdriver (screwdriver not included). (fig. 1) www.sharkclean.com S3601CO_N_11_IB_E_130304_4.indd 3 3 13-03-04 2:53 PM Getting Started - cont’d fig. 2 fig. 4 fig. 5 fig. 3 2 Use the lavender loop on the side of the cleaning pad to slide mop head into pad pocket. Then secure the quick fasteners on the top of the pocket to lock in place. (fig. 2) 3 Snap the mop head into the mop body until you hear it latch into place. (fig. 3) 4 Turn the water tank cap counter clockwise and remove from the tank. (fig. 4) IMPORTANT: Don’t use on unsealed wood or unglazed ceramic floors. On surfaces that have been treated with wax or some no wax floors, the sheen may be removed by the heat and steam action. It is always recommended to test an isolated area of the surface to be cleaned before proceeding. We recommend that you check the use and care instructions from the floor manufacturer. Use the filling flask and pour water into the tank. Please don’t overfill. Replace the cap on the water tank. (fig. 5) 4 TOLL FREE: 1-800-798-7398 S3601CO_N_11_IB_E_130304_4.indd 4 13-03-04 2:53 PM Using Your Steam Mop IMPORTANT: Make sure you don’t use the mop without attaching a cleaning pad and adding water to the tank first. When you are using the mop for the first time, it might take longer than the normal 30 seconds to start steaming. fig. 7 fig. 6 I MPORTANT: Your Steam Mop needs water to make steam! Never use your steam mop without water in the tank. Sweep or vacuum your floors prior to cleaning with your Steam Mop. Visit www.sharkclean.com for other great quick cleaning products to complement your Steam Mop, such as the Shark® Navigator (model NV350). 1 Pull and twist the quick release cord holder to unwrap the power cord completely. Plug into an electrical outlet. (fig. 6) 2 The ON/STANDBY switch will flash blue. If the light does not turn on, reference the troubleshooting section on page 12. (fig. 7) www.sharkclean.com S3601CO_N_11_IB_E_130304_4.indd 5 5 13-03-04 2:53 PM Using Your Steam Mop - cont’d fig. 9 fig. 10 fig. 8 3 Press the ON/STANDBY switch once for dust setting (DUST lighted setting indicator will illuminate). DUST setting is light steam for a quick dusting and best dry time. (fig. 8) Press the ON/STANDBY switch a second time to activate the MOP setting. MOP setting is for normal, everyday steam cleaning. (fig. 9) Press the ON/STANDBY switch a third time to activate the SCRUB setting. SCRUB setting is for heavy cleaning and will leave floors damp. To better understand which steam setting to use for your cleaning task, turn to page 7. 4 Clean your floors with a forward and backward motion. (fig. 10) Press the ON/STANDBY switch until the light flashes to stop the steam. 6 TOLL FREE: 1-800-798-7398 S3601CO_N_11_IB_E_130304_4.indd 6 13-03-04 2:53 PM The Shark® Pro Steam Pocket® Mop has three unique steam settings so you can use the perfect amount of steam for the cleaning task at hand. See below for tips on when to use each setting. Setting Ideal for These Surfaces Laminate DUST Bamboo Hardwood Recommended Usage Light Cleaning and Dusting Loosen and Lift Light Dirt Sanitize Floors Marble MOP Hardwood Basic, everyday cleaning Marble Remove spots and smaller messes Tile Clean moderate and heavilytrafficked areas Stone Sanitize floors Tough cleaning and removal of stuck-on messes and stains Tile SCRUB Deep clean heavily-trafficked areas Stone Cut through heavy dirt and grime Linoleum Sanitize floors Carpet (with Carpet Glider) Freshen area rugs and carpets www.sharkclean.com S3601CO_N_11_IB_E_130304_4.indd 7 7 13-03-04 2:53 PM Using Your Steam Mop - cont’d fig. 11 5 When one side of the cleaning pad gets dirty, just flip the mop head and you can quickly start using the other side. (fig. 11) 6 When the water tank is empty, the steam mop will stop producing steam. You can refill the water tank at any time as long as the mop is unplugged from the outlet. Follow the instructions from page 4. This applies to switching the mop heads or cleaning pad as well. 8 NOTE: Please wait 2-3 minutes for the Steam Mop to cool off before removing the mop head or the cleaning pad. Never leave the steam mop with a damp/wet cleaning pad on any floor. TOLL FREE: 1-800-798-7398 S3601CO_N_11_IB_E_130304_4.indd 8 13-03-04 2:53 PM Using Your Carpet Glider The Steam Mop is great for grooming and freshening though it won’t clean your carpet or area rugs. fig. 12 fig. 13 THE CARPET GLIDER 1 The Carpet Glider can be used with the all-purpose head to lightly steam your carpet and area rugs. Just place the mop head with the cleaning pad attached on top of the glider. The recommended steam setting is SCRUB when using the carpet glider. (fig. 12) 2 Move the steam mop back and forth across a section of the carpet. The steam mop won’t clean your carpeting or areas rugs, but it’s great for grooming and freshening. (fig. 13) www.sharkclean.com S3601CO_N_11_IB_E_130304_4.indd 9 9 13-03-04 2:53 PM Care of Your Steam Mop fig. 14 fig. 16 fig. 15 AFTER USE AND STORAGE 1 When you have finished using the steam mop, press the ON/STANDBY switch until the LED light turns flashing BLUE. This stops the unit from steaming. Unplug the cord from the outlet and place the mop into the upright position. Let the unit cool for 2-3 minutes. Remove the cleaning pad by releasing the quick fasteners and using the lavender loop on the side of the pocket, avoiding contact with the hot pad or dirt. (fig. 14) 10 2 Empty the water tank before storage. Remove the water tank cap and empty the tank over a sink. Replace the water cap. (fig. 15) 3 To store the Shark® Pro Steam Pocket® Mop hanging up, first remove the head (after it has cooled and the steam has been released) then hang on a large hook. (fig. 16) TOLL FREE: 1-800-798-7398 S3601CO_N_11_IB_E_130304_4.indd 10 13-03-04 2:53 PM To order additional parts and accessories, feel free to contact us at www.SharkClean.com or call 1-800-798-7398. fig. 17 CARE OF YOUR CLEANING PAD 1 We recommend washing your cleaning pad separately from other fabrics to avoid picking up lint. Only use liquid detergent (no powder detergent). Don’t use any fabric softeners or bleach. Line dry or dry on a low dryer setting. (fig. 17) 2 If there are loose threads on the cleaning pad carefully cut the thread with scissors. Don’t pull on them or cut at the base. (fig. 18) fig. 18 DECALCIFYING YOUR STEAM MOP Calcium and mineral deposits can build up and impact the performance of your steam mop over time. To extend the life of your product we recommend that you use distilled water or Shark®’s Water Filtration Bottle. Visit www.SharkClean.com to order. www.sharkclean.com S3601CO_N_11_IB_E_130304_4.indd 11 11 13-03-04 2:53 PM Troubleshooting Guide PROBLEM POSSIBLE REASONS & SOLUTIONS The Pro Steam Pocket® Mop will not turn-on. Your Steam Mop should be securely plugged into an electrical outlet only. Check your fuse or breaker. If your unit still does not work, call Customer Care at 1-800-798-7398. The unit will not make steam. Is there water in the water tank? If not, add water to your Steam Mop following instructions on page 4. If the unit still doesn’t make steam, follow the decalcification instructions on page 11. Cannot select steam setting/flashing blue light remains on. If you have already plugged in your unit, unplug and try a different outlet. This may reset the standby mode. Add water to the tank and press the ON/Standby button to select a steam setting. If your unit still does not work, call Customer Care at 1-800-798-7398. The Pro Steam Pocket® Mop leaves water on the floor. Check to see if your cleaning pad is soaked through. We recommend you unplug the Steam Mop and change the cleaning pad. Make sure the cleaning pad is attached correctly. The Pro Steam Pocket® Mop left a white spot on the floor. Do not leave your Steam Mop on the floor with a damp or wet cleaning pad. If you’re using tap water we recommend switching to distilled water. Make sure the cap is securely on the water tank. There is a square block in my water tank. Shark® provides in-tank water treatment media to help reduce scale build-up caused by hard water. The square you are seeing is the water treatment packet that will help minimize the buildup and calcification to extend the life of your mop. Shark® recommends you use distilled water to prevent hard water scaling to ensure the longevity and durability of your mop. Floors are cloudy, streaky or spotty after steaming. The cleaning pad might be dirty. Flip or change the cleaning pad. If you washed the cleaning pad with powder detergent, then it may be damaged and require replacement. Replacement pads are available at www.sharkclean.com. You might have left the mop in the same spot for too long. Do you have hard water? If you do, you might want to switch to distilled water. This might be leftover from past cleaners used on the floor surface. Use the Steam Mop a few more times and see if the leftover cloudiness is removed. If this does not work, we suggest rinsing the floor with water, letting it dry, and then steam mopping again with a clean pad. One or more rinses generally removes the residue. A more stubborn case may require you to rinse the floor with a mix of one part vinegar and two parts water. The Pro Steam Pocket® Mop is hard to push. Make sure the cleaning pad is attached correctly. Check to see if the cleaning pad is excessively dirty. If so, replace the cleaning pad. 12 TOLL FREE: 1-800-798-7398 S3601CO_N_11_IB_E_130304_4.indd 12 13-03-04 2:53 PM Notes www.sharkclean.com S3601CO_N_11_IB_E_130304_4.indd 13 13 13-03-04 2:53 PM Notes 14 TOLL FREE: 1-800-798-7398 S3601CO_N_11_IB_E_130304_4.indd 14 13-03-04 2:53 PM ONE (1) YEAR LIMITED WARRANTY EURO-PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of one (1) year from the date of the original purchase, when utilized for normal household use, subject to the following conditions, exclusions and exceptions. If your appliance fails to operate properly while in use under normal household conditions within the warranty period, return the complete appliance and accessories, freight prepaid. For Customer Service support, call 1 (800) 798-7398 or visit our website www.sharkclean.com. If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will repair or replace it free of charge. Proof of purchase date and $ 19.95 to cover the cost of return shipping and handling must be included. * The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option. This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alterations to the product or any of its parts, which have been performed by a repair person not authorized by EUROPRO Operating LLC. This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional warranties. The responsibility of EURO-PRO Operating LLC warranty if any, is limited to the specific obligations expressly assumed by it under the terms of the limited warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential damages of any nature whatsoever. Some states/ provinces do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province. *Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and to attach tag to item before packing with your name, complete address and phone number with a note giving purchase information, model number and what you believe is the problem with the item. We recommend you insure the package (as damage in shipping is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”. We are constantly striving to improve our products, therefore the specifications contained herein are subject to change without notice. Product Registration Please visit www.sharkclean.com or call 1-800-798-7398 to register your new Shark® product within ten (10) days of purchase. You will be asked to provide the store name, date of purchase and model number along with your name and address. The registration will enable us to contact you in the unlikely event of a product safety notification. By registering you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions. www.sharkclean.com S3601CO_N_11_IB_E_130304_4.indd 15 15 13-03-04 2:53 PM U.S.: EURO-PRO Operating LLC Newton, MA 02459 Canada: EURO-PRO Operating LLC 4400 Bois Franc Ville St. Laurent, Québec H4S 1A7 1-800-798-7398 www.sharkclean.com COPYRIGHT© EURO-PRO OPERATING LLC 2013 Euro-Pro, Shark and Navigator are trademarks of Euro-Pro Operating LLC. All other brand names may be trademarks of their respective owners. PRINTED IN CHINA S3601CO.N.E.130304.4 Illustrations may differ from actual product. S3601CO_N_11_IB_E_130304_4.indd 16 13-03-04 2:53 PM
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Instance ID : uuid:4589c52f-84ee-ac48-bae9-9c9c7ac55021 Original Document ID : adobe:docid:indd:63d2e371-30ab-11de-8edc-b72f0cef3aba Document ID : xmp.id:B5BA83E4B02268118083AFF585A21643 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:B4BA83E4B02268118083AFF585A21643 Derived From Document ID : xmp.did:6B1067DCB22068118C148BEAB4422912 Derived From Original Document ID: adobe:docid:indd:63d2e371-30ab-11de-8edc-b72f0cef3aba Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Macintosh) History Changed : / History When : 2013:03:04 14:53:01-05:00 Create Date : 2013:03:04 14:53-05:00 Modify Date : 2013:03:04 14:53:04-05:00 Metadata Date : 2013:03:04 14:53:04-05:00 Creator Tool : Adobe InDesign CS6 (Macintosh) Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 20 Creator : Adobe InDesign CS6 (Macintosh)EXIF Metadata provided by EXIF.tools