Sharp HRO00025 Cordless Telephone System User Manual Table

Sharp Corporation Cordless Telephone System Table

Users Manual 3

958. Special Functions8. Special FunctionsCaller ID (Requires Subscription to Service)If you subscribe to a caller identification service from your telephone company, you can have the fax machine and the cordless handset display the name and number of the caller when you receive a call.Important:♦To use this function, you must subscribe to a caller identification service from your telephone company.♦Your fax may not be compatible with some caller identification services.1Press once and twice on the fax machine.2Press once and 5 times.3Press once.4Press (YES) to turn on Caller ID.(To turn off Caller ID, press and go to Step 8.)5Press to select SET. (To clear a previously programmed area code, press and go to Step 8.)6Enter the three digits of your area code.FUNCTION1212Display:OPTION SETTINGCALLER-IDAREA CODE # MODEENTER AREA CODE1=YES, 2=NO1=SET, 2=CLEARall.bookPage95Wednesday,February13,200210:00AM
Caller ID (Requires Subscription to Service)967Press to store your area code.8Press to return to the date and time display.START/MEMORYSTOPHow Caller ID operatesWhen you receive a call, the name and phone number of the caller will appear in the fax machine display and cordless handset display, beginning just before the second ring. The information will continue to be displayed until the line is disconnected.Note: Some caller ID services may not provide the name of the caller. In this case, only the phone number will appear.Display messagesOne of the following messages will appear while the fax rings if caller information is not available.NO SERVICE No caller information was received from your telephone company. Make sure that the telephone company has activated your service.CALLER-ID ERROR Noise on the telephone line prevented reception of caller information.OUT OF AREA The call was made from an area which does not have a caller identification service, or the caller’s service is not compatible with that of your local phone company.PRIVATE CALL Caller information was not provided by the telephone company at the caller’s request.Display example (fax machine display)Caller’s name Caller’s numberJOHN DOE 525-8693ECM MODEall.bookPage96Wednesday,February13,200210:00AM
Caller ID (Requires Subscription to Service)978. Special FunctionsViewing the Caller ID listIf you subscribe to a Caller ID service and have turned on the Caller ID function, your fax machine will keep information on the most recent 30 calls and faxes you have received. You can view this information, which consists of the name and number of each caller, in the Caller ID List.♦After you have received 30 calls, each new call will delete the oldest call.♦All calls will be erased if you unplug the fax or a power failure occurs. Follow the steps below to view the Caller ID List in the fax machine display. If desired, you can immediately dial a number when it appears.1Press twice.2Press or to scroll through the list.3If you wish to dial one of the numbers in the list, scroll through the list until the number appears in the display.•Fax: If you wish to send a fax, load the document and then press . Dialing and transmission begin.•Voice call: If you wish to make a voice call, pick up the handset (or press ). Dialing begins automatically. (If you pressed , pick up the handset when the other party answers.)4Press when you have finished viewing the list.START/MEMORYSPEAKERSPEAKERSTOPSTART/MEMORYFax:Voicecall:<REVIEW CALLS>all.bookPage97Wednesday,February13,200210:00AM
Caller ID (Requires Subscription to Service)98To delete calls from the Caller ID listIf you want to delete a single call from the caller list, press while the call appears in the display. If you want to delete all calls from the list, hold down for at least 3 seconds while you are viewing any number in the list.00Viewing the Caller ID list from the cordless handsetYou can also view the Caller ID list in the cordless handset display, and automatically dial a number from the list. (Note that the cordless handset and the fax machine share the same list.)1Press .2Press or to scroll through the numbers in the list.3While viewing the list, you can do the following:•Dial a number: Scroll to the desired number and then press . (Note: You can only make a phone call from the cordless handset; you cannot start a fax transmission.)•Erase a call: Scroll to the call you wish to erase, press , and then press .4Press when you have finished viewing the list.REVIEWTALKERASEHOLDSTARTOFFOFFREVIEW CALLS▲▼: REVIEWCordless handset display:all.bookPage98Wednesday,February13,200210:00AM
Caller ID (Requires Subscription to Service)998. Special Functions1Press once and 3 times.2Press once and once.3Press once.FUNCTIONPriority CallIf you have turned on Caller ID, you can set the machine to make a special ringing sound when you receive a call from a designated phone number. This lets you know immediately who is calling without having to look at the display. To use this function, enter the desired phone number by following the steps below (only one phone number can be entered).Display: ENTRY MODEPRIORITY #1=SET, 2=CLEARErasing all calls using the cordless handsetFollow these steps to erase all calls from the Caller ID list using the cordless handset.1Press .2Press .3Press .•To cancel, press .REVIEWERASEHOLDSTARTOFFOFFREVIEW CALLS▲▼: REVIEWCordless handset display:ERASE ALL?PRESS START KEYall.bookPage99Wednesday,February13,200210:00AM
Caller ID (Requires Subscription to Service)100Blocking voice callsIf you have turned on Caller ID, you can use the Anti Junk Fax function described in Blocking Reception of Unwanted Faxes in this chapter to block voice calls as well as faxes from your specified Anti Junk Number.In this case, when a voice call or a fax transmission comes in from the number you have specified as a "Junk Number", your fax will break the connection as soon as it receives the calling phone number from the caller ID service (before the second ring).To use this function, enter the number that you wish to block as explained in Blocking Reception of Unwanted Faxes (see page 102). Only one number can be blocked.Note: This function cannot be used if you are using the Distinctive Ring function.4Press to store a number. (To clear a previously stored number, press and go to Step 6.)5Enter the number by pressing the number keys (max. 20 digits). 6Press to store (or clear) the number. 7Press to return to the date and time display.12START/MEMORYSTOPOWN NUMBER SETall.bookPage100Wednesday,February13,200210:00AM
Distinctive Ring (Requires Subscription to Service)1018. Special FunctionsDistinctive Ring (Requires Subscription to Service)Important:♦To use distinctive ring, you must subscribe to a distinctive ring service from your local phone company.♦Your fax machine may not be compatible with some distinctive ring services.Distinctive ring is a service offered by some local telephone companies whereby they assign an additional second number to your regular single line. The second number rings differently from your normal number.If you subscribe to a distinctive ring service, you can set the fax machine to automatically answer when your second number is called. This allows you to use the second number as an exclusive fax number. To have your fax automatically answer when your second number is called, follow the steps below:1Press once and twice.2Press once and 3 times.3Press once.4Press a number from 1 to 3 to select the ring pattern below that matches your second number’s ring pattern. Or, press 4 to have your fax automatically answer your normal telephone number. Press 5 to turn off the distinctive ring function.RING PATTERN 1 Two short ringsRING PATTERN 2 One short, one long, and one short ringRING PATTERN 3 Two short rings and one long ringSTANDARD RING Your standard (normal) ring patternOFF SETTING Turn distinctive ring offFUNCTIONDisplay:12345OPTION SETTINGDISTINCTIVEall.bookPage101Wednesday,February13,200210:00AM
Blocking Reception of Unwanted Faxes1025Press to return to the date and time display.6Set the reception mode to FAX.♦When using distinctive ring, you must set the reception mode of your fax machine to FAX. When your designated fax number is dialed, your fax will automatically answer and begin reception after two rings. Note that other devices on the same line will also ring until your fax answers. If one of your other numbers is dialed, the fax will ring; however, it will not answer.STOP1Press once and 3 times.2Press once and twice.3Press once.4Press to store an Anti Junk number, or to clear a previously stored number (if you are clearing a number, go to Step 6).5Enter the fax number by pressing the number keys (max. 20 digits). 6Press and then press to return to the date and time display.FUNCTION12START/MEMORYSTOPBlocking Reception of Unwanted FaxesThe Anti Junk Fax function allows you to block reception of faxes from a party that you specify. This saves paper by not printing out unwanted "junk" faxes. To use this function, follow the steps below to enter the fax number from which you do not wish to receive faxes. One fax number can be entered.The display briefly shows your selection, then:RESOLUTION/RECEPTION MODEDisplay:FAXTELTADFAX SIGNAL RXENTRY MODEANTI JUNK #1=SET, 2=CLEARall.bookPage102Wednesday,February13,200210:00AM
1039. Printing Lists9. Printing ListsYou can print lists showing settings and information entered in the fax machine. The lists are described below. To print a list, follow these steps.1Press once and twice.2Press once.3Press or until the desired list appears in the display.4Press once.5Press to print the list.FUNCTIONSTART/MEMORYDisplay:LISTING MODETEL # LISTPRESS START KEYall.bookPage103Wednesday,February13,200210:00AM
Printing Lists104Message ListThis list shows information about the messages currently recorded in the answering machine, including the date and time each messages was recorded, the length, and the type.Caller-ID ListThis list shows information about your 30 most recent calls. (This list is only available if you are using the Caller ID function.)Telephone Number ListThis list shows the fax and phone numbers that have been stored for automatic dialing.Setup ListThis list shows your current selections for the FUNCTION key settings. The list also shows your name and fax/telephone number as entered in the machine, and a sample of the header printed at the top of every page you transmit (HEADER PRINT).all.bookPage104Wednesday,February13,200210:00AM
Printing Lists1059. Printing ListsTransaction ReportThis report is printed out automatically after an operation is completed to allow you to check the result. Your fax machine is set at the factory to print out the report only when an error occurs. ♦The Transaction report cannot be printed on demand.Headings in Transaction ReportSENDER/RECEIVER The name or fax number of the other machine involved in the transaction. If that machine does not have an ID function, the communication mode will appear (for example, "G3").START The time at which transmission/reception started.TX/RX TIME Total time taken for transmission/reception.PAGES Number of pages transmitted/received.NOTE (One of the following notes will appear under NOTE in the report to indicate whether the transaction was successful, and if not, the reason for the failure.)OK - Transmission/reception was successful.P.FAIL - A power failure prevented the transaction.JAM - The printing paper or document jammed, preventing the transaction.BUSY - The fax was not sent because the line was busy.COM.E-X - (Where “X” is a number.) A telephone line error prevented the transaction. See Line error on page 112.CANCEL - The transaction was cancelled because the STOP key was pressed, no document was in the feeder, or the other machine requested transmission using a function which your fax machine does not have. If you were attempting to fax, make sure a document is in the feeder. If you were receiving, contact the faxing party to see how they are trying to send to you.all.bookPage105Wednesday,February13,200210:00AM
Printing Lists106Transaction Report print conditionYou can change the condition under which a Transaction Report is printed out. Follow the steps below.1Press once and twice.2Press once and once.3Press once.4Press a number from to to select the condition for printing.5Press to return to the date and time display.ALWAYS PRINT A report will be printed after each transmission, reception, or error.ERROR/MEMORY A report will be printed after an error or a memory operation.SEND ONLY A report will be printed after each transmission.ERROR ONLY A report will be printed only when an error occurs.NEVER PRINT A report will never be printed.FUNCTION1 5STOPDisplay:The display briefly shows your selection, then:12345OPTION SETTING TRANSACTION DIAL MODE 1:ALWAYS PRINT(Selections appear alternately)all.bookPage106Wednesday,February13,200210:00AM
10710. Maintenance10. MaintenancePrint headClean the print head frequently to ensure optimum printing performance.Note: Remove the paper from the paper tray before cleaning the print head.1Unplug the power cord, and open the operation panel (press ➊).2Take the imaging film out of the print compartment and place it on a sheet of paper.3Wipe the print head with isopropyl alcohol or denatured alcohol.Caution!•Do not use benzene or thinner. Avoid touching the print head with hard objects.•The print head may be hot if your fax machine has just received a large number of documents. If this is the case, allow the print head to cool prior to cleaning.12Print headall.bookPage107Wednesday,February13,200210:00AM
Maintenance1084Place the imaging film back in the print compartment.5Rotate the front gear until the film is taut, and then close the operation panel (press down on both sides to make sure it clicks into place).Scanning glass and rollersClean the scanning glass and rollers frequently to ensure the quality of transmitted images and copies. Note: Remove the paper from the paper tray before cleaning the scanning glass and rollers.1Open the operation panel (press ➊).12all.bookPage108Wednesday,February13,200210:00AM
Maintenance10910. Maintenance2Flip up the green levers on each side of the white roller.3Wipe the scanning glass (under the white roller) and rollers with a cotton swab.•Make sure that all dirt and stains (such as correcting fluid) are removed. Dirt and stains will cause vertical lines on transmitted images and copies.If the scanning glass is difficult to cleanIf you find it difficult to remove dirt from the scanning glass, you can try moistening the swab with isopropyl alcohol or denatured alcohol. Take care that no alcohol gets on the rollers.4Flip down the green levers on each side of the white roller. Rotate the front gear until the film is taut, and then close the operation panel (press down on both sides to make sure it clicks into place).The housingWipe the external parts and surface of the machine with a dry cloth.Caution!Do not use benzene or thinner. These solvents may damage or discolor the machine.all.bookPage109Wednesday,February13,200210:00AM
Maintenance110Replacing the Cordless Handset BatteryLike any other battery, the rechargeable battery will eventually wear out. The battery can normally be used for about two years, although this will vary depending on the conditions of use.If LOW BATTERY continues to appear in the cordless handset display after the battery has been charged for 10 hours, replace it with the following battery:Replacement battery: Use only a Sharp UX-BA01 battery (3.6 V Ni-MH battery, capacity: 850 mAh)Caution:Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.Dispose of used batteries according to the manufacturer's instructions.1Remove the battery cover by pressing on the indentation as shown.2Unplug the battery connector and remove the old battery.3Connect the battery connector ➊ of the new battery, and then place the battery in the cordless handset, placing the wires as shown.BlackRedBlackRedall.bookPage110Wednesday,February13,200210:00AM
Maintenance11110. Maintenance4Place the battery cover on the cordless handset, making sure it snaps firmly into place.5Place the cordless handset in the charger with the dial pad facing forward.•Let the new battery charge for at least 10 hours.Battery disposalThe battery pack contains a Nickel Metal Hydride battery. The battery must be disposed of properly. Contact local agencies for information on recycling and disposal plans in your area.Wiping the charger contactsTo ensure that the battery charges properly, wipe the charger contacts once a month with a cotton swab.Charger contactsall.bookPage111Wednesday,February13,200210:00AM
11211. TroubleshootingProblems and SolutionsIf you have any problems with your fax, first refer to the following troubleshooting guide. If you cannot solve the problem, call Sharp's Customer Assistance Center at 1-877-794-8675.Line errorProblem SolutionLINE ERROR appears in the display. Try the transaction again. If the error persists, check the following:•Check the connection. The cord from the TEL. LINE jack to the wall jack should be no longer than six feet.•Make sure there are no modem devices sharing the same telephone line.•Check with the other party to make sure their fax machine is functioning properly.•Have your telephone line checked for line noise.•Try connecting the fax machine to a different telephone line.•If the problem still occurs, your fax machine may need service.all.bookPage112Wednesday,February13,200210:00AM
Problems and Solutions11311. Trouble-shootingDialing and transmission problemsProblem SolutionNo dial tone when you pick up the handset or press the SPEAKER key.•Make sure the handset cord is connected to the correct jack. See Connecting the handset on page 14.Dialing is not possible. •Make sure the power cord is properly plugged into a power outlet.•Make sure that the telephone line is properly connected to both the TEL. LINE jack and the wall jack (see page 15).•Make sure that the fax machine is set to the correct dialing mode for your telephone line. See Dial mode on page 15.The power is on, but no transmission takes place. •Make sure that the receiving machine has paper.•If the receiving machine is in manual mode with no attendant, reception will not be possible.•Check the display for error messages.•Pick up the handset and check for a dial tone.Nothing is printed at the receiving end. •Make sure that the document for transmission is placed face down in the feeder.A distorted image is received at the other end. •Noise on the telephone line may cause distortion. Try sending the document again.•Make a copy of the document on your fax machine. If the copy is also distorted, your fax machine may need service.all.bookPage113Wednesday,February13,200210:00AM
Problems and Solutions114Reception and copying problemsProblem SolutionThe fax machine doesn't receive documents automatically.•Make sure that the reception mode is set to FAX. If you subscribe to a distinctive ring service, make sure that the Distinctive Ring function is set to the correct ring pattern. If you do not subscribe to a distinctive ring service, make sure that Distinctive Ring is set to OFF SETTING. (See Distinctive Ring on page 101.)The printing paper comes out blank when you try to receive a document.•Make sure that the document is loaded properly in the feeder of the transmitting machine. Make a copy or print a report to confirm the printing ability of your machine.General print quality is poor. •It is important to select a paper that is appropriate for the thermal transfer printer in your fax. We recommend using laser quality paper that has a very smooth finish. Copier paper will work, but it sometimes tends to yield a lighter print quality.The received document is faint. •Ask the other party to send higher contrast documents. If the contrast is still too low, your fax machine may need service. Make a copy or print a report to check your machine’s printing ability.Received images are distorted. •Noise on the telephone line may cause distortion. Have the other party try sending the document again.•The print head may be dirty. See Print head on page 107.•Make a copy or print a report on your fax machine. If the copy or report is also distorted, your fax machine may need service.A received document or copy prints out in strips. •Make sure the operation panel is completely closed (press down on both sides of the panel). all.bookPage114Wednesday,February13,200210:00AM
Problems and Solutions11511. Trouble-shootingThe quality of copies is poor and/or dark vertical lines appear.•Any dirt or material on the scanning glass will cause spots to appear on copies and transmitted faxes. Clean the scanning glass as explained on page 108.Reception/copying is interrupted. •If reception or copying takes place continuously for a long time, the print head may overheat. Turn off the power and let it cool down. If overheating frequently occurs, try changing the print contrast setting to LIGHT (see page 24).Dark vertical lines appear on copies and received faxes.•Try changing the print contrast setting to LIGHT (see page 24).General problemsProblem SolutionAuto-dial numbers cannot be stored in the fax. •Make sure the fax is plugged in and the imaging film has been loaded. (Auto-dial numbers cannot be stored if the imaging film has not been loaded.) See Loading the Imaging Film in Chapter 1.Nothing appears in the display. •Make sure the power cord is properly plugged into a power outlet.•Connect another electrical appliance to the outlet to see if it has power.The machine does not respond when you press any of its keys.•If a beep sound is not made when you press the keys, unplug the power cord and then plug it in again several seconds later.Automatic document feeding does not work for transmission or copying.•Check the size and weight of the document (see Transmittable Documents on page 73).all.bookPage115Wednesday,February13,200210:00AM
Problems and Solutions116Cordless handset problemsProblem SolutionThe cordless handset does not operate and nothing appears in the display.•Make sure the battery is properly connected inside the cordless handset (see page 18).•The battery may be low. Place the cordless handset in the charger and let it charge.Calls cannot be made or received on the cordless handset.•Make sure the fax machine is plugged into a power outlet and has power.•Make sure the telephone line is properly connected to both the TEL. LINE jack on the fax machine and the wall jack (see page 15). (If the telephone line is connected correctly, you should hear a dial tone when you pick up the fax machine handset.)•The battery may be low. Place the cordless handset in the charger and let it charge.•Calls cannot be made or received while the fax machine is being used (while FAX BUSY appears in the cordless handset display). Wait until the fax machine is no longer being used.•Calls cannot be made or received during a power failure.•You may be outside of the talking range. Move closer to the fax machine.all.bookPage116Wednesday,February13,200210:00AM
Problems and Solutions11711. Trouble-shootingThe battery does not charge. •Make sure the cordless handset is placed in the charger with the dial pad facing forward.•Make sure the AC adapter is connected correctly to the charger and the power outlet (see page 17).•Wipe the charger contacts with a cotton swab.•Make sure the battery is properly connected inside the cordless handset (see page 18).•The battery may need replacement (see page 110).You hear noise or interference during a call. •Make sure the base antenna is fully upright on the fax machine (see page 17).•Other electrical appliances may cause interference. Move away from any electrical appliances. •Move closer to the fax machine. Note that large metal objects, metal structures, and thick walls between the fax machine and cordless handset will reduce the talking range. If needed, try moving the fax machine to a different location.You hear beeps during a call. •You will hear beeps during a call and LOW BATTERY will appear in the display if the battery is low. Place the cordless handset in the charger and let it recharge. If you hear beeps during a call and need to continue the call, press the INTERCOM key to transfer the call to the fax machine.•You will hear beeps during a call and OUT OF RANGE will appear in the display if you are outside of the talking range. Move closer to the fax machine.all.bookPage117Wednesday,February13,200210:00AM
Messages and Signals118Messages and SignalsDisplay messages (fax machine)Note: If you have turned on the Caller ID function, see page 96 for display messages related to Caller ID.ADD PAPER & /PRESS START KEY(alternating messages)Check the printing paper. If the tray is empty, add paper and then press the START/MEMORY key. If there is paper in the tray, make sure it is inserted correctly (take out the stack, align the edges evenly, and then reinsert it in the tray) and then press the START/MEMORY key.CHECK FILM/CHECK COVER/CHECK PAPER JAM(alternating messages)These alternating messages appear when there is a problem in the print compartment that prevents printing. Check to see if the imaging film is not loaded properly or if it has been used up and needs replacement. Make sure the operation panel is completely closed (press down on both sides). If a paper jam has occurred, clear the jam as explained in the following section, Clearing Paper Jams.CHECK PAPER SIZE The paper size setting is incorrect. Change the paper size setting as explained on page 24.CORDLESS IN USE The cordless handset is being used. Wait until this message no longer appears to send a fax or make a phone call.DOCUMENT JAMMED The original document is jammed. See the following section, Clearing Paper Jams. Document jams will occur if you load more than 10 pages at once or load documents that are too thick (see page 73). The document may also jam if the receiving machine doesn’t respond properly when you attempt to send a fax.DOWNLOAD ERROR The fax machine was unable to download rate data from OpenLCR. Try downloading the data manually as explained in Downloading (receiving) the rate data manually on page 36.all.bookPage118Wednesday,February13,200210:00AM
Messages and Signals11911. Trouble-shootingFAX RX IN MEMORY A fax has been received in memory because the imaging film needs replacement, you have run out of printing paper, or the paper is jammed. The fax will print out automatically when the problem is fixed.FUNCTION MODE The FUNCTION key has been pressed.INTERCOM The INTERCOM key has been pressed to page the cordless handset, or the cordless handset is paging the fax machine. Lift the handset to talk. When you are finished talking, replace the handset.LCR DOWNLOADING The fax machine has called OpenLCR and is receiving carrier rate data. This message only appears if you have registered with OpenLCR.LINE ERROR Transmission or reception was not successful. Press the STOP key to clear the message and then try again. If the error persists, see Line Error on page 112.LOW BATTERY This will appear if you have pressed the INTERCOM key to page the cordless handset and the cordless handset battery is too low for the cordless handset to respond.MEMORY IS FULL/SEE MANUAL(alternating messages)The memory is full. You may have too many messages recorded in the answering system. To erase messages, see page 47.This message may also occur during fax reception if too much data is received before the pages can be printed out. If faxes have been received to memory because printing is not possible (an additional message will indicate the problem), resolve the problem so that printing can continue (see Substitute Reception to Memory on page 92). If you are attempting to transmit from memory, see If the memory becomes full on page 86.If you are copying, see If MEMORY IS FULL appears on page 93.MEMORY PRINTING The fax is preparing to or printing out a document from memory.all.bookPage119Wednesday,February13,200210:00AM
Messages and Signals120NO DATA This appears if you attempt to search for an auto-dial number when none have been stored.NO SERVICE This appears if you haven’t registered with OpenLCR and press the FUNCTION key and 7.OFF HOOK This appears if you forgot to replace the handset after using it to dial and send a fax. Replace the handset or press the STOP key to clear the message.ON HOOK DIAL The SPEAKER key has been pressed and the fax machine is waiting for you to dial.OUT OF RANGE This will appear if you have pressed the INTERCOM key to page the cordless handset and it is outside of the talking range.OVER HEAT The print head has overheated. Operation can be continued after it cools. If overheating frequently occurs, try changing the print contrast setting to LIGHT (see page 24).PRINT HEAD FAIL/YOU NEED SERVICE(alternating messages)The print head has failed and requires service.READY TO SEND A document has been loaded and the fax machine is waiting for you to begin faxing or copying.RECALLING This appears if you attempt to send a fax by automatic dialing and the line is busy or the receiving fax machine does not answer. Your fax machine will automatically reattempt the call. (See Automatic redialing on page 83.)REPLACE HANDSET This appears if an outside call comes in while you are paging or talking to the cordless handset using the Intercom feature. Replace the fax machine handset to stop the Intercom call, and then pick it up again to answer the outside call.T.A.D. TRANSFER The answering system's transfer function has been turned on (see page 50).all.bookPage120Wednesday,February13,200210:00AM
Messages and Signals12111. Trouble-shootingTOTAL MSGS:XX This indicates that you have received messages in the answering system. “XX” is the number of messages.TOTAL PAGE(S) 01 Number of pages transmitted, received, or copied.Display messages (cordless handset)CHARGING The cordless handset is in the charger and the battery is charging.FAX BUSY The fax machine is in use. Wait until the fax machine is no longer being used to use the cordless handset.HOLD A call has been placed on hold by pressing the HOLD key. To resume the call, press the HOLD key again.IN CHARGER The cordless handset is in the charger and is fully charged (the cordless handset can be left in the charger without damaging the battery).INTERCOM The INTERCOM key has been pressed to page the fax machine, or the fax machine is paging the cordless handset. Press the TALK key to talk. When you are finished, press the OFF key.LOW BATTERY The cordless handset battery is low. Place the cordless handset in the charger and let it recharge. If this message continues to appear after recharging, the battery may need replacement (see page 110). If this message appears during a phone call (you will also hear beeps) and you wish to continue the call, press the INTERCOM key to transfer the call to the fax machine.NEW MESSAGES New messages have been received in the answering system. You can either listen to the messages using the cordless handset (see page 71), or using the fax machine (see page 46).all.bookPage121Wednesday,February13,200210:00AM
Messages and Signals122OUT OF RANGE The cordless handset is outside of the talking range of the fax machine. When talking on the cordless handset, the handset will beep and you may hear interference. Move closer to the fax machine.REMOTE MODE The REMOTE/FLASH key has been pressed. For information on using REMOTE MODE, see page 71.STAND-BY This appears when the cordless handset is not in the charger and is ready to be used.TALK The TALK key has been pressed to make a phone call.Audible signalsContinuous tone 3 seconds Indicates the end of transmission, reception, or copying.Intermittent tone (3 beeps) 5 seconds(1 second on, 1 second off)Indicates incomplete transmission, reception, or copying.Rapid intermittent tone 35 seconds(0.7 seconds on, 0.3 seconds off)Indicates that the handset is off hook.all.bookPage122Wednesday,February13,200210:00AM
Clearing Paper Jams12311. Trouble-shootingClearing Paper JamsClearing a jammed documentIf the original document doesn’t feed properly during transmission or copying, or DOCUMENT JAMMED appears in the display, first try pressing . If the document doesn't feed out, remove it as explained below.Important:Do not try to remove a jammed document without releasing it as explained below. This may damage the feeder mechanism.START/MEMORY1Press ➊ and slowly open the operation panel until it is half open.2Flip up the green levers on each side of the white roller.3Gently remove the document.•Be careful not to tear the document.12all.bookPage123Wednesday,February13,200210:00AM
Clearing Paper Jams1241Open the operation panel (press ➊).2Gently pull the jammed paper out of the machine, making sure no torn pieces of paper remain in the print compartment or rollers.3Rotate the front gear until the film is taut, and then close the operation panel (press down on both sides to make sure it clicks into place).Clearing jammed printing paper4Flip down the green levers on each side of the white roller. Rotate the front gear until the film is taut, and then close the operation panel (press down on both sides to make sure it clicks into place).12all.bookPage124Wednesday,February13,200210:00AM
Ordering Parts125Ordering PartsTo order parts, contact the parts distribution center located nearest you. When ordering a part, use the part order number shown below. Operation manual TINSE4267XHTASetup Guide TCADZ3323XHZZHandset cord QCNWG209BXHBWTelephone line cord QCNWG208BXHZZHandset DUNTK468BXHBWPaper tray CPLTP3183XHR7Paper tray extension LPLTP3184XHZZGears CGERH2566XH01NGERH2568XHZZAC adapter RADPA2027XHZZCordless handset charger RUNTZ2100XHE1Part distribution centers Tritronics, Inc. 1306 Continental Drive Abingdon, MD 21009Tel: 1-800-638-3328 Fax: 1-800-888-FAXD Tritronics, Inc. 1015 NW 52nd Street Ft. Lauderdale, FL 33309Tel:1-800-365-8030 Fax: 1-800-999-FAXDFox International, Ltd. 23600 Aurora Road Bedford Heights, OH 44146Tel: 1-800-321-6993 Fax: 1-800-445-7991Andrews Electronics 25158 Avenue Stanford Santa Clarita, CA 91355Tel: 1-800-274-4666 Fax: 1-805-295-5126Sharp Accessories and Supply Center 2130 Townline Road Peoria, IL 61615Tel: 1-800-642-2122all.bookPage125Wednesday,February13,200210:00AM
FCC Regulatory Information126FCC Regulatory InformationThis equipment complies with FCC rules, Part 68. On this equipment is a label that contains, among other information, the Registration Number and Ringer Equivalence Number (REN) for this equipment. If requested, this information must be provided to your telephone company. An FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack which is Part 68 compliant. This equipment connects to the telephone network through a standard USOC RJ-11C network interface jack. The REN is used to determine the quantity of devices which may be connected to your telephone line and still have all of those devices ring when your number is called. Too many devices on one line may result in the devices not ringing in response to an incoming call. In most, but not all, areas as the sum of the RENs of all devices should not exceed five (5.0). To be certain of the number of devices that may be connected to your line, as determined by the total REN, contact your local telephone company. If this equipment causes harm to the telephone network, your telephone company may disconnect your service temporarily. If possible, they will notify you in advance. If advance notice is not practical, you will be notified as soon as possible. You will also be advised of your right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of your equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. If the equipment is causing harm to the telephone network, your telephone company may ask you to disconnect the equipment until the problem resolved. If you have any questions or problems which cannot be solved by reading this manual, please contact Sharp’s Customer Assistance Center. The number is 1-877-794-8675.This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs. Contact your state’s public utility commission, public service commission, or corporation commission for more information. This equipment is hearing-aid compatible. When programming and/or making test calls to emergency numbers: ♦Remain on the line and briefly explain to the dispatcher the reason for the call. ♦Perform such activities in the off-peak hours, such as early morning or late evening. all.bookPage126Wednesday,February13,200210:00AM
127SHARPDate Revised: .Date Issued :July. 3. 2001MATERIAL SAFETY DATA SHEET (1/2)MSDS No. B-1026Section 1. Product and Company IdentificationProduct Name : IMAGING FILM UX-5CRSupplier Identification : Sharp Corporation22-22 Nagaike-cho, Abeno-ku, Osaka, JapanManufacturer : DAINIPPON PRINTING CO. LTD.591-2, Kamihirose, Higashikubo, Sayamashi, Saitama, 350-1321 JAPANEmergency telephone number : +81-42-952-9666Local suppliers are listed below. Please contact the nearest supplier for additional information.Section 2. IngredientsIngredients CAS No. Proportion OSHA PEL ACGIH TLV OtherPolyethylene terephthalate film25038-59-9 47 ~ 52% - - NoneCoating layer substancesCarbon Black 1333-86-4 7 ~ 10% 3.5 mg/m33.5 mg/m3NoneEster wax 8015-86-9 2 ~ 7% - - NoneParraffin Wax 8002-74-2 10 ~ 14% - 2.0 mg/m3NoneMicrocrystalline wax 63231-60-7 16 ~ 22% - - NoneEthylene Vinyl Acetate Copolymer24937-78-8 1 ~ 5% - - NoneOthers 1 ~ 6% - - NoneSection 3. Hazardous IdentificationRoute(s) of Entry: Inhalation? Skin? Ingestion?NO NO Possible but very unusualSigns and Symptoms of Exposure: NoneMedical Conditions Aggravated by Exposure: NonePOTENTIAL HEALTH EFFECTS:Inhalation: NoneSkin Contact: NoneEye Contact: NoneIngestion: NoneSection 4. First-Aid MeasuresInhalation: No applicableSkin Contact: In case of contact, usually special care in not necessary. If it dirties skin, clear with water and soap.Eye Contact: In case of contact, immediately flush eyes with plenty of water. If necessary, then care for medical attention.Ingestion: Immediately make vomit it and rinse mouth with water. If necessary, then care for medical attention.Section 5. Fire-Fighting MeasuresFlash Point: about 250°CforinkAutoignition: NoneFlammability Limits: Not applicableExtinguishing Media: CO2, Water, Dry chemicals, FoamFirefighting: NoneFire and Explosion Hazard: NoneHazardous Combustion Products: None(Country) (Name and Telephone Number)U.S.A. Sharp Electronics CorporationTelephone number for information: 1-800-237-4277Canada Sharp Electronics of Canada Ltd.Telephone number for information : 905-890-2100Emergency telephone number : 1-800-255-3924all.bookPage127Wednesday,February13,200210:00AM
128SHARPDate Revised: .Date Issued :July. 3. 2001MATERIAL SAFETY DATA SHEET (2/2)MSDS No. B-1026Section 6. Accidental Release MeasuresRumpling the product may cause the wax layer to peel off. Sweep up or vacuum. When sweeping, avoidraising film or dust. If a vacuum is used , motor should be rated as dust tight. Wash any residue off skin withsoap and water. Garments may be wasted or dry cleaned after removal of loose film or dust.Section 7. Handling and StorageNo special precautions for safety reason.Store in cool, dry place ,avoid direct sunlight.Section 8. Exposure Control/Personal ProtectionVentilation: NoneEye Protection: NoneProtective Clothing: NoneGloves: NoneSection 9. Physical and Chemical PropertiesDescription: Not applicableMelting Point: 71°CFreezing Point: NonePressurized: None Boiling Point: NonepH: None Specific Gravity (H20 = 1): about 1.2Evaporation Rate: Negligible Water Solubility: Not applicableVolatility: NoneSection 10. Stability and ReactivityStability: StableConditions to Avoid: NoneIncompatibility(Materials to Avoid): NoneHazardous Decomposition or Byproducts: CO, CO2, NOX and H2OHazardous Polymerization: Will not occurSection 11. Toxicological InformationAcute Toxicity: NoneChronic Toxicity: NoneSection 12. Ecological InformationNo environmental effect at normal use.Section 13. Disposal ConsiderationDispose by the same method of ordinary plastic products in accordance with all applicable regulations. Anydisposal practice must be in compliance with local, state and federal laws and regulations. If necessary,contact government office and ensure conformity with disposal regulations.Section 14. Transport InformationNo specific precautionary transport measure for safety reasons.As to storage conditions, see section 7.Section 15. Regulatory InformationNoneSection 16. Other InformationThe information herein is given in good faith, but no warranty, if used any process.Final determination of suitability of any material is the sole responsibility of the user.Although certain information are described herein, we cannot guarantee, that these are the only hazard, which exist.Information on this data sheet represents our current data and best opinion as to the proper use in handling ofthis product under normal conditions.Restrictions: This information relates only to the specific material designated as supplied by the manufacturer. Thisinformation is supplied to us by the manufacturer and Sharp offers no warranties as to its accuracy andaccepts no responsibilities for any typographical errors which may appear on these sheets. It is theresponsibility of the user to determine the suitability of this product for each particular use.all.bookPage128Wednesday,February13,200210:00AM
129Quick Reference GuideSending FaxesPlace your document (up to 10 pages) face down in the document feeder.Normal Dialing 1.Lift the handset or press .2. Dial the fax number. 3. Wait for the reception tone (if a person answers, ask them to press their Start key). 4. Press .Automatic Dialing1. Press or until the desired destination appears in the display.2. Press .Direct Keypad Dialing 1. Dial the fax number. 2. Press .Recording an Outgoing Message1. Press , , and .2. Lift the handset, press , and speak into the handset.3. When finished, press .SPEAKERSTART/MEMORYSTART/MEMORYSTART/MEMORYREC/MEMOSTART/MEMORYSTOPReceiving FaxesPress until the arrow in the display points to the desired reception mode.FAX mode: The fax machine automatically answers and receives faxes.TEL mode: Answer all calls (even faxes) by picking up the handset. To begin fax reception, press .TAD mode: Select this mode when you go out to receive both voice messages and faxes.Storing Auto Dial Numbers1. Press once and twice.2. Enter the full fax/phone number.3. Press .4. Enter a name by pressing number keys. (To enter two letters in succession that require the same key, press after entering the first letter.)5. Press and then .RESOLUTION/RECEPTION MODESTART/MEMORYFUNCTIONSTART/MEMORYSTART/MEMORYSTOPFAXTELJAN-01 10:30FAXTELJAN-01 10:30FAXTELJAN-01 10:30TADTADTADRESOLUTION/RECEPTION MODEA =B =C =D =E =F =G =H =I =J =K =L =M =N =O =P =Q =R =S =T =U =V =W =X =Y =Z =SPACE =all.bookPage129Wednesday,February13,200210:00AM
130Using the Cordless PhoneMaking a phone call1. Pick up the cordless handset and press .2. When you hear the dial tone, dial the number. 3.When you are ready to end the call, press . Making a phone call using automatic dialing1. Press once.2. Press or until the number you wish to dial appears in the display.3. Press .Receiving a phone call1.When the cordless handset rings, pick it up and press any key to answer.2. When you are ready to end the call, press .Receiving a fax using the cordless handsetIf you hear a fax tone after answering a call on the cordless handset, or if the other party speaks to you and then wants to send a fax, press .TALKOFFOFFSEARCHTALKOFFOFFSTARTStoring auto dial numbers1. Press and then .2. Enter the full fax/phone number.To clear a mistake, press .To insert a pause, press .3. Press .4. Enter a name by pressing number keys. (To enter two letters in succession that require the same key, press after entering the first letter.)5. Press and then .Listening to messages received in the answering system1. Press .2. Press to listen to all your messages, or to listen to only your new messages.3. While listening, you can press , , , or .4 When finished, press SEARCHFUNCTION/PAUSEERASEHOLDFUNCTION/PAUSESTARTSTARTOFFOFFREMOTE/FLASHPQRS7PLAYTUV8PLAY NEWREPEAT0SKIP DELETE STOPWXYZ9OFFOFFA =B =C =D =E =F =G =H =I =J =K =L =M =N =O =P =Q =R =S =T =U =V =W =X =Y =Z =SPACE =WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9TUV8TUV8TUV8TUV8TUV8TUV8PQRS7PQRS7PQRS7PQRS7PQRS7PQRS7PQRS7PQRS7PQRS7PQRS7MNO6MNO6MNO6MNO6MNO6JKL5JKL5JKL5MNO6JKL5JKL5JKL5GHI4GHI4GHI4GHI4GHI4GHI4DEF3DEF3DEF3DEF3DEF3DEF3ABC2ABC2ABC2ABC2ABC2ABC21all.bookPage130Wednesday,February13,200210:00AM
131Guía de referencia rápidaTransmisión de mensajes telefaxColoque el original (hasta 10 páginas) cara abajo en el alimentador de documentos.Marcación normal 1.Levante el auricular u oprima: .2.Marque el número de telefax. 3.Espere hasta escuchar el tono de recepción (si contestara una persona, pídale oprimir su tecla Start). 4. Oprima: .Marcación automática1. Oprima la tecla de flecha o hasta que en el visor aparazca el destino deseado.2. Oprima: .Marcación directa por teclado 1.Marque el número de fax. 2.Oprima: .Grabacion de un mensaje de bienvenida1. Oprima la tecla , tecla de flecha , y .2. Levante el auricular, oprima la tecla y hable en el microteléfono.3. Oprima la tecla cuando haya finalizado.SPEAKERSTART/MEMORYSTART/MEMORYSTART/MEMORYREC/MEMOSTART/MEMORYSTOPRecepción de mensajes telefaxOprima hasta que la flecha que hay en el display señale hacia el número de recepción deseadoModo FAX: El aparato telefax contesta y transmite automáticamente mensajes telefax.Modo TEL: Responda a todas las llamadas (incluso mensajes de fax), levantando el auricular. Para iniciar la recepción de fax, oprima .Modo TAD: Seleccione este modo cuando salga para recibir tanto mensajes hablados como telefax.Memorizar números marc. automática1. Oprima una vez y dos veces.2. Introduzca el número de telefax/teléfono completo.3. Oprima: .4. Ingrese el nombre oprimiendo las teclas numéricas. (Para ingresar sucesivamente dos letras que requieren la misma tecla, oprima después de ingresar la primera letra).5. Oprima y luego .RESOLUTION/RECEPTION MODESTART/MEMORYFUNCTIONSTART/MEMORYSTART/MEMORYSTOPFAXTELJAN-01 10:30FAXTELJAN-01 10:30FAXTELJAN-01 10:30TADTADTADRESOLUTION/RECEPTION MODEA =B =C =D =E =F =G =H =I =J =K =L =M =N =O =P =Q =R =S =T =U =V =W =X =Y =Z =SPACE =all.bookPage131Wednesday,February13,200210:00AM
132Uso del teléfono inalámbricoHacer una llamada1. Descuelgue el teléfono inalámbrico y oprima .2.Marque los números cuando escuche el tono de línea.3. Oprima cuando esté listo para finalizar la llamada. Hacer una llamada usando la función de marcación automática1. Oprima una vez .2. Oprima o hasta que en el display aparezca el número que desea llamar.3. Oprima .Recibir una llamada1. Cuando suene el timbre del teléfono inalámbrico, descuélguelo y oprima una tecla cualquiera para contestar.2. Oprima cuando esté listo para finalizar la llamada.Recibir un mensaje telefax usando el teléfono inalámbricoSi después de atender una llamada con el teléfono inalámbrico escucha el tono de telefax o si el interlocutor desea remitirle un mensaje telefax, oprima .TALKOFFOFFSEARCHTALKOFFOFFSTARTMemorizar números para marcación automática1. Oprima y, a continuación, .2. Introduzca el número de teléfono/telefax completo.Para borrar un error, oprima .Para introducir una pausa, oprima .3. Oprima .4. Introduzca un nombre mediante pulsación de las teclas numéricas.(Para introducir dos letras consecutivas que requieran el mismo código, oprima después de introducir la primera letra.5. Oprima y, a continuación, .Escuchar mensajes recibidos en el sistema de contestador automático1. Oprima .2. Oprima para escuchar todos sus mensajes o para escuchar sólo los mensajes nuevos. 3. Mientras hace la escucha puede pulsar , , , o .4. Pulse cuando haya terminado. SEARCHFUNCTION/PAUSEERASEHOLDFUNCTION/PAUSESTARTSTARTOFFOFFREMOTE/FLASHPQRS7PLAYTUV8PLAY NEWREPEAT0SKIP DELETE STOPWXYZ9OFFOFFA =B =C =D =E =F =G =H =I =J =K =L =M =N =O =P =Q =R =S =T =U =V =W =X =Y =Z =SPACE =WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9TUV8TUV8TUV8TUV8TUV8TUV8PQRS7PQRS7PQRS7PQRS7PQRS7PQRS7PQRS7PQRS7PQRS7PQRS7MNO6MNO6MNO6MNO6MNO6JKL5JKL5JKL5MNO6JKL5JKL5JKL5GHI4GHI4GHI4GHI4GHI4GHI4DEF3DEF3DEF3DEF3DEF3DEF3ABC2ABC2ABC2ABC2ABC2ABC21all.bookPage132Wednesday,February13,200210:00AM
133AAnswering system, activating, 44Anti Junk Fax, 102Audible signals, 122Auto-dial numbersStoring, 63, 78Using, 65, 81BBatteryDisposing of, 111Installing, 18Replacing, 110CCaller ID, 95-100Caller ID List, 104Contrast, 76Copies, 93Copy cut-off setting, 94Cordless handsetAuto-dial numbers, storing, 63Auto-dial numbers, using, 65Faxes, receiving, 63Hold, 62Listening to messages, 71Making a call, 61Receiver volume, 32Receiving a call, 62Reception mode, changing, 71Redialing, 67Ringer volume, 32Talking range, 19DDate, setting, 27-28Daylight Saving Time, 28Dial mode, 15DialingAutomatic, 65, 81Direct Keypad, 82Normal, 61, 77Direct Keypad Dialing, 82Display messages, 37, 96, 118-122Distinctive ring, 101Document feeder, 74Document guides, 74Document restrictions, 74Document sizes, 73Document, maximum scanning size, 73EECM (Error Correction Mode), 84Extension telephone, using, 89FFAX reception mode, 29, 87Fax reception on TAD failure, 48Fax Signal Receive, 90HHalftone setting, 75Handset, 14Handset receiver volume (fax machine), 30Headset jack, 20Housing, cleaning, 109IImaging film, replacing, 21Intercom, 68JJams, clearing, 123-124LLetters, entering, 26, 64, 79Line error, 112Loading paper, 23Indexall.bookPage133Wednesday,February13,200210:00AM
Index134Loading the document, 74MMemory transmission, 86Memory, substitute reception to, 92Message List, 104MessagesErasing, 47, 72Listening to, 46Listening to on cordless handset, 71Listening to remotely, 56Setting allowed time, 48NNormal dialing, 61, 77Number of rings in FAX reception mode, 87Number of rings in TAD mode, 45OOGM only mode, 49OpenLCR, 33-42Ordering parts, 125Outgoing message, 43Override Ringing, 53PPaper jams, clearing, 123-124Paper size setting, 24Paper tray extension, 16Paper, loading, 23Power cord, 14Print contrast setting, 24Print head, cleaning, 107-108Priority Call, 99RReception modeFAX mode, 29, 87TAD mode, 29, 44TEL mode, 29, 88Reception Ratio setting, 91Redialing, 67, 83Remote code number, 55Remote operations, 55Resolution, 75Ringer volumeCordless handset, 32Fax machine, 31SScanning glass, cleaning, 108Sender’s name and number, entering, 25-26Setup List, 104Speaker volume, 30TTAD reception mode, 29, 44TEL reception mode, 29, 88TEL. LINE jack, 15Telephone line cord, 15Telephone Number List, 104Time, setting, 27-28Toll Saver function, 45, 55Transaction Report, 105Setting print condition, 106Transfer Function, 50Transferring calls, 69all.bookPage134Wednesday,February13,200210:00AM
1. Call your fax from a touch-tone telephone, and press # when the outgoing message begins. 2. Enter your remote code: . 3. Press # . 4. After listening to your messages, you can either hang up to save them, or enter one of the commands on the reverse side. REMOTE OPERATION CARD The card below is provided as a quick guide to remote operation. Cut it out and carry it with you when you go out. Remote Operation Guideall.bookPage136Wednesday,February13,200210:00AM
REMOTE COMMANDS•FAX RECEPTION MODES TAD mode......................... 81#FAX mode......................... 82#TEL mode......................... 83#•TRANSFER FUNCTION Turn on ............................. 91#Turn off ............................. 92#New transfer number ........ 90# (Tel. #) #Record transfer OGM ....... 93#To quickly disconnect........ ** •OGM ONLY MODE Turn on ............................. 11# Turn off ............................. 12# •PLAYBACK Play messages ................. 7# Move backward/repeat...... 2#Skip forward...................... 5#Stop .................................. 0#Play new messages only .. 6#(first stop playback) •ERASING MESSAGES Erase single message ...... 3# Erase all messages .......... 33#•RECORDING A MEMO Start .................................. *# End ................................... 0# •RECORDING A NEW OGM Start .................................. 4*all.bookPage137Wednesday,February13,200210:00AM
all.bookPage138Wednesday,February13,200210:00AM
END USER LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first end user purchaser that this Sharpbrand product (the "Product"), when shipped in its original container, will be free from defectiveworkmanship and materials, and agrees that it will, at its option, either repair the defect or replacethe defective Product or part thereof with a new or remanufactured equivalent at no charge to thepurchaser for parts or labor for the period(s) set forth below. This warranty does not apply to any appearance items of the Product nor to the additional excludeditem(s) set forth below nor to any product the exterior of which has been damaged or defaced,which has been subjected to misuse, abnormal service or handling, or which has been altered ormodified in design or construction. In order to enforce the rights under this limited warranty, the purchaser should follow the steps setforth below and provided proof of purchase to the servicer. To the extent permitted by applicable state law, the warranties set forth herein are in lieu of, andexclusive of, all other warranties, express or implied. Specifically, ALL OTHER WARRANTIESOTHER THAN THOSE SET FORTH ABOVE ARE EXCLUDED. ALL EXPRESS AND IMPLIEDWARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE,AND FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED. If, underapplicable state law, implied warranties may not validly be disclaimed or excluded, the duration ofsuch implied warranties is limited to the period(s) from the date of purchase set forth below. Neither the sales personnel of the seller nor any other person is authorized to make any warrantiesother than those described above, or to extend the duration of any warranties beyond the timeperiod described above on behalf of Sharp. The warranties described herein shall be the sole and exclusive warranties granted by Sharp andshall be the sole and exclusive remedy available to the purchaser. Correction of defects, in themanner and for the period of time described herein, shall constitute complete fulfillment of allliabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shallconstitute full satisfaction of all claims, whether based on contact, negligence, strict liability orotherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defectsin the Product which were caused by repairs or attempted repairs performed by anyone other thanan authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental orconsequential economic or property damage. Some states do not allow limits on warranties or onremedies for breach in certain transactions; in such state the limits herein may not apply. Your Product: Personal Facsimile UX-CL220 Warranty Period for this Product: Ninety (90) days parts and labor from date of purchase. Additional items excluded Any consumable items such as paper or Imaging Film supplied with from warranty coverage: the Product. What to do to obtain service: Call Sharp at 1-877-794-8675 to obtain a Return Authorization Number and shipping instructions. A technician will troubleshoot your problem with youon the phone and if it is determined that your Product needs service, youwill have your choice of having your unit repaired or replaced to any U.S.location. Be sure to have Proof of Purchase available. For product information or customer assistance, please visit http://www.sharpusa.com on theWorld Wide Web or call 1-877-794-8675.SHARP ELECTRONICS CORPORATIONSharp Plaza,Mahwah, New Jersey 07430-2135all.bookPage138Wednesday,February13,200210:00AM
IMPORTANT SERVICE INFORMATIONIf a Problem OccursMost operational questions can be answered by referring to this "Setup Guide and Operation Manual"Also, for your convenience, you will find answers to most frequently askedquestions on our website at www.sharpusa.com/, or by sending e-mail to faxsupport@sharpsec.com. Should you require further assistance, call 1-877-794-8675; a Customer Relations Specialist will assist you. Before your call, please be ready to provide the model number of your product, serial number, date of purchase, description of the problem, and a valid credit card number (should it be required).How Exchange is ObtainedA replacement unit in exchange for your fax is provided by Sharp to any U.S. location. You will be required to provide consent for acceptance of an exchange unit and provide credit card authorization. At that time, Sharp will ship to you, at no cost, an exchange for your defective product. The exchange unit we ship to you will be new or remanufactured. Upon your receipt of the exchange unit, packaging and shipping instructions will be enclosed for you to return the defective unit. Upon Sharp's receipt of the defective unit, your credit card hold will be released.How Warranty Repair Service is ObtainedIf you prefer that we repair your unit instead of replacing it, our Customer Relations Specialists at 1- 877-794-8675 will explain how to obtain warranty repair service. Please be sure to retain the original packaging materials in order to facilitate shipment. Upon repair of your unit, Sharp will promptly return it at no cost to you at any U.S. location.What You Must DoYour Product is designed to perform with a minimum amount of user maintenance. However, you are responsible for the required user maintenance described in the "Operation Manual". This requires user maintenance including replacement of the imaging film and battery, cleaning of the unit and removal of dust and foreign matter, clearing of paper misfeeds, and proper routine and preventive maintenance.Service After Expiration of Warranty CoverageShould you require service repair after warranty coverage has expired, contact Sharp at 1-877-794- 8675 for information.To Purchase Consumables From SharpVisit www.sharpplace.com/ or call Sharp at 1-877-794-8675 to order replacement Sharp Thermal Ribbons & Accesories. Before your call, please be ready to provide the model number of your product, and a valid credit card number. Consumables may also be obtained through your reseller.all.bookPage139Wednesday,February13,200210:00AM
all.bookPage140Wednesday,February13,200210:00AM
PRINTED IN THAILAND(TINSE4267XHTA)SHARP ELECTRONICS CORPORATIONSharp Plaza, Mahwah, New Jersey 07430-2135SHARP CORPORATIONFOR YOUR RECORDSPlease record the model number and serial number below, for easy reference, in case of loss or theft. These numbers are located on the rear side of the unit.Space is also provided for other relevant information.Model Number UX-CL220Serial NumberDate of PurchasePlace of Purchaseall.bookPage139Wednesday,February13,200210:00AM

Navigation menu