Sharp HRO00142 Mobile Terminal Equipment User Manual EB W51GJ Quick Tips indd

Download:
Mirror Download [FCC.gov]
Document ID	1377333
Application ID	nbda5Q1NqT4OIO/N9UiXjQ==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	18.38kB (229718 bits)
Date Submitted	2010-11-17 00:00:00
Date Available	2011-01-01 00:00:00
Creation Date	2010-11-12 15:34:41
Producing Software	Acrobat Distiller 8.0.0 (Windows)
Document Lastmod	2010-11-12 16:54:07
Document Title	EB-W51GJ_Quick Tips.indd
Document Creator	Adobe InDesign CS3_J (5.0.4)
Document Author:	DTP_NARA

EB-W51GJ Quick Tips
EB-WX1GJ
Charge the product
The product is not fully charged when you purchase it.
Before using the product for the first time or when the
battery has run low, charge the battery.
● Only use the specified AC adapter. Using an AC adapter other than
the specified type may cause a fire or electric shock.
● If the product is not charged after the prescribed charging time has
elapsed, stop charging. Continuing to charge the product may cause
a fire or electric shock.
1. Insert the power plug of the AC adapter
into a power socket.
2. Insert the connector of the AC adapter
into the product's power/mini-USB
connector.
Power/mini-USB
connector
When charging starts, the battery indicator on the
front side of the product ( ) turns red. When the
product is fully charged, the battery indicator turns
off.
3. When charging is finished, remove the
connector of the AC adapter.
4. Disconnect the AC adapter from the
power socket.
EB-W51GJ_Quick Tips.indd 1
2010/11/12 15:34:31
Turn on/off the power
„ Turn on the power
1. Press the power key.
Rear side of
product
„ Turn off the power
1. Hold down the power key for 2 seconds.
The menu is displayed.
2. Tap [電源OFF].
3. Tap [OK].
Setup
„ STEP 1 : Configure wireless LAN settings
Register information about the access point you will use.
● Users are liable for communication and connection charges required
when using the wireless LAN function.
● These instructions cover the configuration procedure for an access
point using AOSS.
1. Turn on the power by pressing the
power key.
2. Tap [端末登録].
3. Tap [AOSSで接続].
4. Tap [AOSS].
Press the AOSS button on the access point device
(the wireless LAN base station).
5. When the [AOSS終了] screen appears,
tap [OK].
The [登録処理開始] screen appears.
EB-W51GJ_Quick Tips.indd 2
2010/11/12 15:34:32
„ STEP 2 : Register the product
1. On the [登録処理開始] screen, tap [登録
開始].
After a few seconds, a user ID and password entry
screen appears.
2. Enter your user ID and password, and
tap [ログイン].
3. Tap [OK].
Setup is now complete.
FCC Notice
● This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
● Changes or modifications not expressly approved by
the manufacturer responsible for compliance could
void the user’s authority to operate the equipment.
Information to User
This equipment has been tested and found to comply
with the limits of a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not
occur in a particular installation; if this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
EB-W51GJ_Quick Tips.indd 3
2010/11/12 15:34:32
1. Reorient/relocate the receiving antenna.
2. Increase the separation between the equipment and
receiver.
3. Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV
technician for help.
FCC RF Exposure Information
Your device is a radio transmitter and receiver. It is
designed and manufactured not to exceed the emission
limits for exposure to radio frequency (RF) energy set
by the Federal Communications Commission of the U.S.
Government.
The guidelines are based on standards that were
developed by independent scientific organizations
through periodic and thorough evaluation of scientific
studies. The standards include a substantial safety
margin designed to assure the safety of all persons,
regardless of age and health.
The exposure standard for wireless devices employs a
unit of measurement known as the Specific Absorption
Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg.
EB-W51GJ_Quick Tips.indd 4
Printed in China
6060A1215302
10L IAC HI c
2010/11/12 15:34:32

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : DTP_NARA
Create Date                     : 2010:11:12 15:34:41+09:00
Modify Date                     : 2010:11:12 16:54:07+09:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Title                           : EB-W51GJ_Quick Tips.indd
Creator                         : DTP_NARA
Creator Tool                    : Adobe InDesign CS3_J (5.0.4)
Metadata Date                   : 2010:11:12 16:54:07+09:00
Producer                        : Acrobat Distiller 8.0.0 (Windows)
Document ID                     : uuid:f8111bb9-926a-47e3-8199-d1e6918bc870
Instance ID                     : uuid:937efb9a-3712-40fe-ba9c-2071cad21551
Page Count                      : 4

EXIF Metadata provided by EXIF.tools