Shen Zhen WFLY Technology Development WFT06XWFT08S Radio Control-Transmitter User Manual

Shen Zhen WFLY Technology Development Co., Ltd. Radio Control-Transmitter Users Manual

Contents

User Manual 1

WFT06X Radio Control System
INSTRUCTION V1
Use in model aerocraft/helicopter
Notice
Please read this instruction before you use the product.
Please put away the instruction.
WFT06X-A: 6 channels airplane, mix function, D/R, HDE helicopter.
WFT06X-B: 4 channesl airplane, mix function, D/R, HDE helicopter.
WFT06X-C: 6 channels CCPM helicopter, airplane.
(1) At airplane state, channel 1, 2, 4, 6 is a switch for dual rate (D/R) variable: from ±100% to ±125%.
(2) At airplane state, channel 1 & 6 mixture function: Flaperon.
(3) At airplane state, channel 4 & 2 mixture function: V-tail.
(4) At airplane state, channel 1 & 2 mixture function: Triangle wing(ELEVON).
(5) At helicopter state, channel 3 mixture function is to channel 4 & channel 6.
(6) At helicopter state, channel 3 mixture function is only to channel 6.
(7) Channel 1, 2, 3, 4, 6 reverse switch.
(8) Normal mode can be used in car model and boat model.
(9) Sound-and-light hint notification for low power: when the battery voltage is below 8.8V, the power
indicator light 1S/1S glitters and buzzes. And when it is below 8.3V, the power indicator light 0.5S/1S
glitters and buzzes at the same time.
WFT06X-A Function Introduction (6 channels)
This item has functions of both airplane and helicopter, and emphasizes more
on airplane.
The main functions are as follows:
The main functions are as follows:
(1) Channel 1, 2, 4 power adjusted function.
(2) Standard 4 channel functions.
(3) At airplane state, channel 1 & 2 mixture function: Triangle wing (ELEVON).
(4) Channel 1, 2, 3, 4 reverse switch.
(5) Sound-and-light hint notification for low power: when the battery voltage is below 8.8V, the
power indicator light 1S/1S glitters and buzzes. And when it is below 8.3V, the power indicator light
0.5S/1S glitters and buzzes at the same time.
WFT06X-B Function Introduction (4 channels)
This item is a popular model with 4 channels. It is mainly used for airplane or
helicopter with mixture functions.
WFT06X-C Function Introduction (6 channels)
www.wflysz.com
Digital Proportional R/C System
This model has functions of CCPM helicopter and airplane,
but emphasizes on helicopter.
The main functions are as follows:
(1) Pitch Zero Trim (PZT).
(2) Pitch Length Trim (PLT).
(3) Be used for CCPM helicopter, airplane, car, boat. Standard 6 channels output.
(4) Compatible with simulation softwares.
(5) Channel 1, 2, 3, 4, 6 reverse switch.
(6) CCPM helicopter pitch reverse.
(7) CCPM state, aileron reverse switch.
(8) CCPM state, elevator reverse switch.
(9) Normal flying and 3D flying. The transmitter will alarms if it is turned on in a Idle-up state, and no output.
(10) Dual rate.
(11) Throttle hold.
(12) Gyro sensitivity adjust.
(13) Idle-up throttle adjust.
(14) Sound-and-light indicator for low power: When the battery voltage is below 8.8V, the power indicator light
1S/1S glitters and buzzes. When it is below 8.3V, the power indicator light 0.5S/1S glitters and buzzes at the
same time.
WFT06X R/C System
User Manual
WFT06X R/C System
User Manual
WFT06X R/C System
User Manual
WFT06X R/C System
User Manual
1Catalogue------------------------------------------------------------------------1
2Special Symbol Explanation-------------------------------------------------2
3Flight Warning------------------------------------------------------------2
4Parts Description/Operation Instruction----------------------------------3
5 Operation of Transmitter & Functions of Control Rods--------------------5
6WFT06X-A Introduction-------------------------------------------------6
7WFT06X-B Introduction--------------------------------------------8
8WFT06X-C Introduction---------------------------------------------------------------9
To use the product safely, please pay attention to the instructions as follows.
Please pay special attention to the symbol as follow:
DangersIf you use it without proper operation, it is possible to hurt you seriously or may
even cause death.
WarningsIf you use it without proper operation, it may make you or others to hurt badly
or may even cause death ,and it may cause slight hurt or damage to things.
NoticesIf you use it without proper operation, it may cause you to hurt slightly or damage
things , but it won't hurt you seriously normally.
Children under 14 must be accompanied and instructed by adults!
Special Symbol Instruction
Forbiddance! Obligation! Warning
Flying Notice(warning)
Same frequencies can't
fly at the same time. Same frequencies used synchronously will cause
the plane to prang or to damage even the modulation
ways of AM, FM, PCM are not the same, when the
frequencies are identical, it will cause the plane to
prang or to damage.
You mustn't play it at night , in the rainy day ,or in the
day with strong wind, which will damage the device or
plane.
The antenna of the transmitter should be pulled out
when using it. Otherwise, the signal will be weakened
and the control range will become smaller, which will
cause the plane to crash.
Please check whether every servo works properly
and any disturbing signals from the outside
environment or not before you play it. (If the radio
bounces after turning off the power, there may be
some disturbances, in this case, please change into
partnership crystals )
Checking
Catalogue
Thanks for choosing products
Turn on the transmitter first, then the receiver. When turning off the system, turn off
the receiver first, then the transmitter.
changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
Parts Description & Operation Instruction
WFT06X-A Transmitter Features (Front)
1AILAileronChannel 1
2ELEElevatorChannel 2
3THRThrottleChannel 3
4RUDRudderChannel 4
5GYRLanding Gear/GyroChannel 5
6PITFlaperon /Screw-pitchChannel 6
{
Elevator Trim
Power Light
Antenna
Landing Gear/Gyro Switch
Neckstrap Attachment
Power Trim
Aileron/Throttle
Control Rod
Aileron Trim
Power Switch
Rudder Trim
Elevator/Rudder
Control Rod
Flaperon /Screw-pitch
Handle
Crystal Jack
Battery Cover
Charge Jack
PC Simulator Jack
WFT06X Transmitter Features (Rear)
WFT06X Side of Radio
Underside of Transmitter
Coupling Ways of WFR06S 6CH Receiver
WFT06X R/C System
User Manual
WFT06X R/C System
User Manual
(9.6V,<200mA)
+
-·
(When using the simulator, pull out the TX.)
1AILAileron (Channel 1)----------------
2ELEElevator (Channel 2)------------
3THRThrottle (Channel 3)--------------
4RUDRudder (Channel 4)-----------
5GYRLanding Gear/Gyro (Channel 5)
6PITFlaperon/Pitch (Channel 6--------
WFR06S Six Channels Receiver
Antenna
Power; 9.6-12V
Power input:4.8-6v
Operation of Transmitter
Functions of Control Rods
MODEL 1
(Channel 2:Elevator) (Channel 1:Aileron)
(Elevator TRIM) (Aileron TRIM)
Ascend
Descend
Left Right
high
Low
Left Right
high
Low
Left Right
Left Right
Ascend
Descend
(Channel 4:Elevator) (Channel 3:Power)
(Rudder TRIM) (Power TRIM)
MODEL 2
(Channel 3:Throttle) (Channel 1:Aileron)
(Power TRIM) (Aileron TRIM)
Channel 4:RudderChannel 2:Elevator
(Rudder TRIM) (Elevator TRIM)
Channel 6: Screw-pitch/Flaperon Action
The angle adjusting of the flaperon is for the airplane state, and the adjusting of the main
screw-pitch is for helicopter state.
Channel 5: Landing Gear/Gyro Action
This channel is for switch variable. It is a switch to control landing gear when used for airplane
state, but it will be a switch for gyroscope when used for helicopter.
Channel 4: Rudder Action
Control the swerve of the aerocraft. Turning the control rod to left will make the head of the
aircraft turn left, and turning it to right will make the head turn right.
Channel 3: Throttle Operation
Control the power. Pulling the control rod down will minish down the power group, and boosting
the control rod up will increase the power group.
Channel 2: Elevator Action
Control the aerocraft to descend or ascend. Pulling the control rod down will drive up the head,
and the aeroplane will ascend. Boosting it up will make the head downhill, and the aeroplane
will descend.
Channel 1: Aileron Action
Control the right-and-left lean of the aircraft. To level the slantwise aircraft, you must make
the control rod act in reverse direction. Otherwise, it will make the aircraft overturn .
WFT06X R/C System
User Manual
WFT06X R/C System
User Manual
R
2. Operation Instructions
1. Code matching
A. Press Set to start the receiver or press Set and hold. The orange
LED flashes, indicating the receiver waits for the code matching signal.
2.4G system can automatically recognize WFLY PPM.
WFLY 2.4G Operation instructions
B. Press Power to start the transmitter. Press Power again to enter the code
matching function. The orange LED of the receiver lights up. Press Power and
hold until the orange LED flashes,indicating the receiver enters the code
matching status.
C. If the code matches successfully, the green LED of the transmitter lights up.
The LED of the receiver is off.
The receiver is on. The red LED lights up. Wait for the
powering up of the transmitter.
The receiver is on. The green LED of the transmitter
lights up. The LED of the receiver is off.
3. Fail Safe Setting
A.Power on receiver.
B.Press Set to start transmitter and hold for 2 seconds.the green LEDflashes,
indicating the transmitter enters the code matching status.
C.The Green LED of receiver flashes, the output data of transmitter is the
output data of Fail Safe Set receiver
D.Due to the heavy interference or out of normal range, the receiver enters Fail
Safe. The Red LED of receiver lights when it is in Fail Safe status.
Flash
WFT06X-A Function Introduction
This model has functions of both airplane and helicopter,
and emphasizes more on airplane.
Switch Function Instruction
(A) At helicopter state, pulling A down to put off mixture function of channel 3 to channel 4, when pulling it up
it will comeback the function. But the mixture function to channel 6 is stable, which is irrelevant with this
switch.
(B) Pulling B down is airplane state and pulling it up is helicopter state.
(C) At airplane state, pulling 1, 2, 4, 6 down the dual rate is ±100%; when pulling them up, the dual
rate will be ±125%.
(D) At airplane state, pulling D down make switches have no mixture function, but pulling it up will cause them
have the function.
(E) At airplane state, when D is pulled up, pulling E down cause channel 1 & 6 mixture function (Flaperon);
pulling E up will cause channel 2 & 4 mixture function(V-TAIL.
(F) At airplane state, when D is pulled up, pulling F up it works as the mixture function of channel 1 &
2(Triangle wing ELEVON), and D function doesn’ t work at that moment.
(G) Channel 1 is reverse switch for aileron. Pulling G down is to make it in normal mode, and pulling it up is
to make it act in reverse.
(H) Channel 2 is reverse switch for elevator. Pulling H down is to make it in normal mode, and pulling it up is
to make it act in reverse.
(I) Channel 3 is reverse switch for power. Pulling I down is to make it in normal mode, and pulling it up is to
make it act in reverse.
(J) Channel 4 is reverse switch for rudder. Pulling J down is to make it in normal mode, and pulling it up is to
make it act in reverse.
(K) Channel 6 is reverse switch for screw-pitch/ flaperon .Pulling K down is to make it in normal mode, and
pulling it up is to make it act in reverse.
H4ON
A-4/2
REV
R
NO
H4OFF
A-1/6
HELI
A-3D
A-MIX
123
(A)( B)( C)(D)(E)(F) (G) (H) (I) (J) ( K)
A-1/2
46
ACRO
A-NOR
A-NOR
A-NOR
AIL
ELE
THR
RUD
PIT
(1) At airplane state, channel 1, 2, 4, 6 is a switch for dual rate(D/R) variable: from ±100% to ±125%.
(2) At airplane state, channel 1 & 6 mixture function: Flaperon.
(3) At airplane state, channel 4 & 2 mixture function: V-tail.
(4) At airplane state, channel 1 & 2 mixture function: Triangle wing(ELEVON).
(5) At helicopter state, channel 3 mixture function is to channel 4 & channel 6.
(6) At helicopter state, channel 3 mixture function is only to channel 6.
(7) Channel 1, 2, 3, 4, 6 reverse switch.
(8) Normal mode can be used in car model and boat model.
(9) Sound-and-light hint notification for low power: when the battery voltage is below 8.8V, the power
indicator light 1S/1S glitters and buzzes. And when it is below 8.3V, the power indicator light 0.5S/1S
glitters and buzzes at the same time.
Mixture Functions of Helicopter
Having the mixture functions of channel 4 will unlock the tail. So when this
happens, you can pulling A down and pulling B up.
when A and B switches are up, channel 3 will control the mixture function of
channel 4 and 6.That is, when pushing channel 3 control rod, both the main
rotor's distance and the tail rotor’s distance will be enlarged. So if the rotor
distance become nearer, you should only turn the reverse switch of the
corresponding channel.
Model with Ordinary Gyro:
Model with Special Functions Gyro:
1CH6CH
When B, E, F are down and D is up: the aileron uses two
servos. If you turn the channel 6 switch, the left and right
aileron can fluctuate at the same time. Pushing channel
1 rod to right-and-left direction can make the left and right
aileron differential.
The left aileron is connected to CH6 and the right one is
connected to CH1.
Mixture Functions of Airplane's Flaperon
2CH
4CH
(4CH)
(2CH)
When E, D are up and B, F are down: It is used in V-tail
aerocraft. CH2 elevator and CH4 rudder's mixture
function will cause the aerocraft to descend /ascend
or swerve.
Airplane's V-TAIL
WFT06X R/C System
User Manual
WFT06X R/C System
User Manual
CH1 CH2
WFT06X R/C System
User Manual
WFT06X R/C System
User Manual
Mixture Function for Triangle Airplane
When B, F are down and D, E are up, it is used for triangle airplanes.
CH1 aileron and CH2 elevator are mixed together, which can make the
aircraft turn up, turn down and turn around.
WFT06X-B Function Introduction
This model is a popular model with 4 channels. It is mainly used
for airplane or helicopter with mixture functions.
The main functions are as follows
(1) Channel 1, 2, 4 power adjusted functions.
(2) Standard 4 channel functions.
(3) At airplane state, channel 1 & 2 mixture function: Triangle wing (ELEVON).
(4) Channel 1, 2, 3, 4 reverse switch.
(5) Sound-and-light hint notification for low power: when the battery voltage is below 8.8V, the
power indicator light 1S/1S glitters and buzzes. And when it is below 8.3V, the power indicator light
0.5S/1S glitters and buzzes at the same time.
Switch Function Instruction:
(A) Turn up A, the movement of channel 1, 2, 4 is 100%, and
turn it down is small movement.
(B) Channel 1 & 2 mixture function: Triangle wing(ELEVON).
(C) Channel 1 is reverse switch for aileron. Pulling it down
is to make it in normal mode, and pulling it up is to make
it act in reverse.
(D) Channel 2 is reverse switch for elevator. Pulling it down
is to make it in normal mode, and pulling it up is to make
it act in reverse.
(E) Channel 3 is reverse switch for power. Pulling it down
is to make it in normal mode, and pulling it up is to make
it act in reverse.
(F) Channel 4 is reverse switch for rudder, pulling it down is to
make it in normal mode, and pulling it up is to make it act in
Reverse.
A-1/ 2
1234
A-NOR
( A ) ( B ) ( C ) ( D ) ( E ) ( F )
D/R
REV
NOR
This model has functions of CCPM helicopte and airplane,
but emphasizes on helicopter.
WFT06X-C Function Introduction
The main functions are as follows:
(1) Pitch Zero Trim (PZT).
(2) Pitch Length Trim (PLT).
(3) Be used for CCPM helicopter, airplane, car, boat. Standard 6 channels output.
(4) Compatible with simulation softwares.
(5) Channel 1, 2, 3, 4, 6 reverse switch.
(6) CCPM helicopter pitch reverse.
(7) CCPM state, aileron reverse switch.
(8) CCPM state, elevator reverse switch.
(9) Normal flying and 3D flying. The transmitter will alarms if it is turned on in a Idle-up state, and no output.
(10) Dual rate.
(11) Throttle hold.
(12) Gyro sensitivity adjust.
(13) Idle-up throttle adjust.
(14) Sound-and-light indicator for low power: When the battery voltage is below 8.8V, the power indicator light
1S/1S glitters and buzzes. When it is below 8.3V, the power indicator light 0.5S/1S glitters and buzzes at the
same time.

Navigation menu