Shen Zhen WFLY Technology Development WFT06XWFT08S Radio Control-Transmitter User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1119279
Application ID	NoibBx7A3vCGpnfZLNEUXQ==
Document Description	User Manual 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	23.2kB (289986 bits)
Date Submitted	2009-06-04 00:00:00
Date Available	2009-06-04 00:00:00
Creation Date	2009-05-04 16:23:53
Producing Software	Corel PDF Engine Version 1.0.0.458
Document Lastmod	0000-00-00 00:00:00
Document Title	Users Manual
Document Creator	CorelDRAW 版本 12.0

WFT06X R/C System
User
Manual
WFT06X-A Function Introduction (6 channels)
www.wflysz.com
INSTRUCTION V1
At airplane state, channel 1, 2, 4, 6 is a switch for dual rate (D/R) variable: from ±100% to ±125%.
At airplane state, channel 1 & 6 mixture function: Flaperon.
At airplane state, channel 4 & 2 mixture function: V-tail.
At airplane state, channel 1 & 2 mixture function: Triangle wing(ELEVON).
At helicopter state, channel 3 mixture function is to channel 4 & channel 6.
At helicopter state, channel 3 mixture function is only to channel 6.
Channel 1, 2, 3, 4, 6 reverse switch.
Normal mode can be used in car model and boat model.
Sound-and-light hint notification for low power: when the battery voltage is below 8.8V, the power
indicator light 1S/1S glitters and buzzes. And when it is below 8.3V, the power indicator light 0.5S/1S
glitters and buzzes at the same time.
Use in model aerocraft/helicopter
WFT06X-B Function Introduction (4 channels)
This item is a popular model with 4 channels. It is mainly used for airplane or
helicopter with mixture functions.
The main functions are as follows:
(1)
(2)
(3)
(4)
(5)
Channel 1, 2, 4 power adjusted function.
Standard 4 channel functions.
At airplane state, channel 1 & 2 mixture function: Triangle wing (ELEVON).
Channel 1, 2, 3, 4 reverse switch.
Sound-and-light hint notification for low power: when the battery voltage is below 8.8V, the
power indicator light 1S/1S glitters and buzzes. And when it is below 8.3V, the power indicator light
0.5S/1S glitters and buzzes at the same time.
WFT06X-C Function Introduction (6 channels)
This model has functions of CCPM helicopter and airplane,
but emphasizes on helicopter.
The main functions are as follows:
(1) Pitch Zero Trim (PZT).
(2) Pitch Length Trim (PLT).
(3) Be used for CCPM helicopter, airplane, car, boat. Standard 6 channels output.
(4) Compatible with simulation softwares.
(5) Channel 1, 2, 3, 4, 6 reverse switch.
(6) CCPM helicopter pitch reverse.
(7) CCPM state, aileron reverse switch.
(8) CCPM state, elevator reverse switch.
(9) Normal flying and 3D flying. The transmitter will alarms if it is turned on in a Idle-up state, and no output.
(10) Dual rate.
(11) Throttle hold.
(12) Gyro sensitivity adjust.
(13) Idle-up throttle adjust.
(14) Sound-and-light indicator for low power: When the battery voltage is below 8.8V, the power indicator light
1S/1S glitters and buzzes. When it is below 8.3V, the power indicator light 0.5S/1S glitters and buzzes at the
same time.
Manual
WFT06X Radio Control System
This item has functions of both airplane and helicopter, and emphasizes more
on airplane.
The main functions are as follows:
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
User
WFT06X R/C System
WFT06X-A: 6 channels airplane, mix function, D/R, HDE helicopter.
WFT06X-B: 4 channesl airplane, mix function, D/R, HDE helicopter.
WFT06X-C: 6 channels CCPM helicopter, airplane.
Notice
▲Please read this instruction before you use the product.
▲Please put away the instruction.
Digital Proportional R/C System
User
WFT06X R/C System
Manual
User
WFT06X R/C System
Manual
Special Symbol Instruction
Catalogue
To use the product safely, please pay attention to the instructions as follows.
Please pay special attention to the symbol as follow:
1、 Catalogue------------------------------------------------------------------------1
2、 Special Symbol Explanation-------------------------------------------------2
3、 Flight
Warning------------------------------------------------------------2
Dangers：If you use it without proper operation, it is possible to hurt you seriously or may
even cause death.
Warnings：If you use it without proper operation, it may make you or others to hurt badly
or may even cause death ,and it may cause slight hurt or damage to things.
Notices：If you use it without proper operation, it may cause you to hurt slightly or damage
things , but it won't hurt you seriously normally.
Children under 14 must be accompanied and instructed by adults!
Turn on the transmitter first, then the receiver. When turning off the system, turn off
4、 Parts Description/Operation Instruction----------------------------------3
5、 Operation of Transmitter & Functions of Control Rods--------------------5
6、 WFT06X-A
Introduction-------------------------------------------------6
7、 WFT06X-B
Introduction--------------------------------------------8
the receiver first, then the transmitter.
changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
Flying Notice(warning)
Same frequencies can't
fly at the same time.
8、 WFT06X-C Introduction---------------------------------------------------------------9
Forbiddance!
Obligation!
Warning
※ Same frequencies used synchronously will cause
the plane to prang or to damage even the modulation
ways of AM, FM, PCM are not the same, when the
frequencies are identical, it will cause the plane to
prang or to damage.
※ You mustn't play it at night , in the rainy day ,or in the
day with strong wind, which will damage the device or
plane.
※ The antenna of the transmitter should be pulled out
when using it. Otherwise, the signal will be weakened
and the control range will become smaller, which will
cause the plane to crash.
Checking
Thanks for choosing
products
※ Please check whether every servo works properly
and any disturbing signals from the outside
environment or not before you play it. (If the radio
bounces after turning off the power, there may be
some disturbances, in this case, please change into
partnership crystals )
User
WFT06X R/C System
Manual
User
WFT06X R/C System
Manual
WFT06X Transmitter Features (Rear)
Parts Description & Operation Instruction
WFT06X-A Transmitter Features (Front)
Crystal Jack
Power; 9.6-12V
Battery Cover
Antenna
WFT06X Side of Radio
Power Light
Landing Gear/Gyro Switch
Charge Jack(9.6V,<200mA)
Handle
Neckstrap Attachment
·
Flaperon /Screw-pitch
Power Trim
Elevator/Rudder
Control Rod
Aileron/Throttle
Control Rod
Elevator Trim
Underside of Transmitter
PC Simulator Jack
Rudder Trim
(When using the simulator, pull out the TX.)
Aileron Trim
Power Switch
Coupling Ways of WFR06S 6CH Receiver
1．AIL：Aileron（Channel 1）
2．ELE：Elevator（Channel 2）
3．THR：Throttle（Channel 3）
4．RUD：Rudder（Channel 4）
5．GYR：Landing Gear/Gyro（Channel 5）
6．PIT：Flaperon /Screw-pitch（Channel 6）
WFR06S Six Channels Receiver
1．AIL：Aileron (Channel 1)---------------2．ELE：Elevator (Channel 2)-----------3．THR：Throttle (Channel 3)-------------4．RUD：Rudder (Channel 4)----------5．GYR：Landing Gear/Gyro (Channel 5)
6．PIT：Flaperon/Pitch (Channel 6--------
Power input:4.8-6v
Antenna
User
WFT06X R/C System
Manual
(Channel 2:Elevator)
WFLY 2.4G
(Channel 3:Throttle)
(Channel 1:Aileron)
Left
Descend
Right
Left
Low
(Aileron TRIM)
(Power TRIM)
(Aileron TRIM)
(Channel 4:Elevator)
(Channel 3:Power)
（Channel 4:Rudder）
（Channel 2:Elevator）
high
Right
Low
Flash
Right
(Elevator TRIM)
Left
1. Code matching
A. Press Set to start the receiver or press Set and hold. The orange
LED flashes, indicating the receiver waits for the code matching signal.
high
Ascend
Operation instructions
2.4G system can automatically recognize WFLY PPM.
MODEL 2
(Channel 1:Aileron)
Manual
Operation of Transmitter
Functions of Control Rods
MODEL 1
User
WFT06X R/C System
B. Press Power to start the transmitter. Press Power again to enter the code
matching function. The orange LED of the receiver lights up. Press Power and
hold until the orange LED flashes,indicating the receiver enters the code
matching status.
Ascend
Left
Right
Descend
C. If the code matches successfully, the green LED of the transmitter lights up.
The LED of the receiver is off.
(Rudder TRIM)
(Power TRIM)
(Rudder TRIM)
(Elevator TRIM)
Channel 1: Aileron Action
Control the right-and-left lean of the aircraft. To level the slantwise aircraft, you must make
the control rod act in reverse direction. Otherwise, it will make the aircraft overturn .
2. Operation Instructions
The receiver is on. The red LED lights up. Wait for the
powering up of the transmitter.
Channel 2: Elevator Action
Control the aerocraft to descend or ascend. Pulling the control rod down will drive up the head,
and the aeroplane will ascend. Boosting it up will make the head downhill, and the aeroplane
will descend.
Channel 3: Throttle Operation
Control the power. Pulling the control rod down will minish down the power group, and boosting
the control rod up will increase the power group.
Channel 4: Rudder Action
Control the swerve of the aerocraft. Turning the control rod to left will make the head of the
aircraft turn left, and turning it to right will make the head turn right.
Channel 5: Landing Gear/Gyro Action
This channel is for switch variable. It is a switch to control landing gear when used for airplane
state, but it will be a switch for gyroscope when used for helicopter.
Channel 6: Screw-pitch/Flaperon Action
The angle adjusting of the flaperon is for the airplane state, and the adjusting of the main
screw-pitch is for helicopter state.
The receiver is on. The green LED of the transmitter
lights up. The LED of the receiver is off.
3. Fail Safe Setting
A.Power on receiver.
B.Press Set to start transmitter and hold for 2 seconds.the green LEDflashes,
indicating the transmitter enters the code matching status.
C.The Green LED of receiver flashes, the output data of transmitter is the
output data of Fail Safe Set receiver
D.Due to the heavy interference or out of normal range, the receiver enters Fail
Safe. The Red LED of receiver lights when it is in Fail Safe status.
User
WFT06X R/C System
Manual
WFT06X-A Function Introduction
This model has functions of both airplane and helicopter,
and emphasizes more on airplane.
Mixture Functions of Helicopter
Model with Ordinary Gyro:
when A and B switches are up, channel 3 will control the mixture function of
channel 4 and 6.That is, when pushing channel 3 control rod, both the main
rotor's distance and the tail rotor’s distance will be enlarged. So if the rotor
distance become nearer, you should only turn the reverse switch of the
corresponding channel.
Model with Special Functions Gyro:
Having the mixture functions of channel 4 will unlock the tail. So when this
4 6
RUD
REV
△
▽
NO R
Mixture Functions of Airplane's Flaperon
PIT
ELE
THR
A-1/2
Manual
happens, you can pulling A down and pulling B up.
AIL
A-NOR
A-4/2
A-MIX
A-NOR
A-1/6
HELI
A-3D
A-NOR
H4OFF
ACRO
H4ON
(1) At airplane state, channel 1, 2, 4, 6 is a switch for dual rate(D/R) variable: from ±100% to ±125%.
(2) At airplane state, channel 1 & 6 mixture function: Flaperon.
(3) At airplane state, channel 4 & 2 mixture function: V-tail.
(4) At airplane state, channel 1 & 2 mixture function: Triangle wing(ELEVON).
(5) At helicopter state, channel 3 mixture function is to channel 4 & channel 6.
(6) At helicopter state, channel 3 mixture function is only to channel 6.
(7) Channel 1, 2, 3, 4, 6 reverse switch.
(8) Normal mode can be used in car model and boat model.
(9) Sound-and-light hint notification for low power: when the battery voltage is below 8.8V, the power
indicator light 1S/1S glitters and buzzes. And when it is below 8.3V, the power indicator light 0.5S/1S
glitters and buzzes at the same time.
User
WFT06X R/C System
When B, E, F are down and D is up: the aileron uses two
(A)( B)( C)(D)(E)(F) (G) (H) (I) (J) ( K)
servos. If you turn the channel 6 switch, the left and right
aileron can fluctuate at the same time. Pushing channel
1 rod to right-and-left direction can make the left and right
Switch Function Instruction
(A) At helicopter state, pulling A down to put off mixture function of channel 3 to channel 4, when pulling it up
it will comeback the function. But the mixture function to channel 6 is stable, which is irrelevant with this
switch.
(B) Pulling B down is airplane state and pulling it up is helicopter state.
(C) At airplane state, pulling 1, 2, 4, 6 down the dual rate is ±100%; when pulling them up, the dual
rate will be ±125%.
(D) At airplane state, pulling D down make switches have no mixture function, but pulling it up will cause them
have the function.
(E) At airplane state, when D is pulled up, pulling E down cause channel 1 & 6 mixture function (Flaperon);
pulling E up will cause channel 2 & 4 mixture function(V-TAIL）.
(F) At airplane state, when D is pulled up, pulling F up it works as the mixture function of channel 1 &
2(Triangle wing ELEVON), and D function doesn’ t work at that moment.
(G) Channel 1 is reverse switch for aileron. Pulling G down is to make it in normal mode, and pulling it up is
to make it act in reverse.
(H) Channel 2 is reverse switch for elevator. Pulling H down is to make it in normal mode, and pulling it up is
to make it act in reverse.
(I) Channel 3 is reverse switch for power. Pulling I down is to make it in normal mode, and pulling it up is to
make it act in reverse.
(J) Channel 4 is reverse switch for rudder. Pulling J down is to make it in normal mode, and pulling it up is to
make it act in reverse.
(K) Channel 6 is reverse switch for screw-pitch/ flaperon .Pulling K down is to make it in normal mode, and
pulling it up is to make it act in reverse.
6CH
1CH
aileron differential.
The left aileron is connected to CH6 and the right one is
connected to CH1.
Airplane's V-TAIL
When E, D are up and B, F are down: It is used in V-tail
aerocraft. CH2 elevator and CH4 rudder's mixture
function will cause the aerocraft to descend /ascend
2CH
4CH
(4CH) (2CH)
or swerve.
User
WFT06X R/C System
Manual
WFT06X R/C System
User
Manual
WFT06X-C Function Introduction
Mixture Function for Triangle Airplane
When B, F are down and D, E are up, it is used for triangle airplanes.
CH1
CH2
CH1 aileron and CH2 elevator are mixed together, which can make the
aircraft turn up, turn down and turn around.
WFT06X-B Function Introduction
This model is a popular model with 4 channels. It is mainly used
for airplane or helicopter with mixture functions.
The main functions are as follows：
(1)
(2)
(3)
(4)
(5)
Channel 1, 2, 4 power adjusted functions.
Standard 4 channel functions.
At airplane state, channel 1 & 2 mixture function: Triangle wing (ELEVON).
Channel 1, 2, 3, 4 reverse switch.
Sound-and-light hint notification for low power: when the battery voltage is below 8.8V, the
power indicator light 1S/1S glitters and buzzes. And when it is below 8.3V, the power indicator light
0.5S/1S glitters and buzzes at the same time.
A-1/ 2
A-NOR
D/R
Switch Function Instruction:
(A) (B)(C)(D)(E )(F)
(A) Turn up A, the movement of channel 1, 2, 4 is 100%, and
turn it down is small movement.
(B) Channel 1 & 2 mixture function: Triangle wing(ELEVON).
(C) Channel 1 is reverse switch for aileron. Pulling it down
is to make it in normal mode, and pulling it up is to make
it act in reverse.
REV (D) Channel 2 is reverse switch for elevator. Pulling it down
△
is to make it in normal mode, and pulling it up is to make
▽
NOR
it act in reverse.
(E) Channel 3 is reverse switch for power. Pulling it down
is to make it in normal mode, and pulling it up is to make
it act in reverse.
(F) Channel 4 is reverse switch for rudder, pulling it down is to
make it in normal mode, and pulling it up is to make it act in
Reverse.
This model has functions of CCPM helicopte and airplane,
but emphasizes on helicopter.
The main functions are as follows:
(1) Pitch Zero Trim (PZT).
(2) Pitch Length Trim (PLT).
(3) Be used for CCPM helicopter, airplane, car, boat. Standard 6 channels output.
(4) Compatible with simulation softwares.
(5) Channel 1, 2, 3, 4, 6 reverse switch.
(6) CCPM helicopter pitch reverse.
(7) CCPM state, aileron reverse switch.
(8) CCPM state, elevator reverse switch.
(9) Normal flying and 3D flying. The transmitter will alarms if it is turned on in a Idle-up state, and no output.
(10) Dual rate.
(11) Throttle hold.
(12) Gyro sensitivity adjust.
(13) Idle-up throttle adjust.
(14) Sound-and-light indicator for low power: When the battery voltage is below 8.8V, the power indicator light
1S/1S glitters and buzzes. When it is below 8.3V, the power indicator light 0.5S/1S glitters and buzzes at the
same time.


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-702
Creation Date--Text             : 
Producer                        : Corel PDF Engine Version 1.0.0.458
Mod Date--Text                  : 
Creator Tool                    : CorelDRAW 版本 12.0
Modify Date                     : 2009:05:21 16:56:55+08:00
Metadata Date                   : 2009:05:21 16:56:55+08:00
Format                          : application/pdf
Title                           : 06X英文说明书V1
Document ID                     : uuid:c978373a-f669-40cc-a864-2ede63e3eb9f
Instance ID                     : uuid:e66a39ba-abb0-4e27-95b4-7737cb1a43d8
Page Count                      : 7
Create Date                     : D:20090504162353
Creator                         : CorelDRAW 版本 12.0

EXIF Metadata provided by EXIF.tools