ShenZhen LanGi Technology 6001000RT Wireless Video Transmission User Manual UPDATED FCC 11 2
ShenZhen LanGi Technology Co. LTD. Wireless Video Transmission UPDATED FCC 11 2
User Manual
‐1‐
The Manual of the Product
Table of Contents
ImportantInformation......................................................................................‐1‐
SpecialNotice:...................................................................................................‐2‐
Introduction.......................................................................................................‐3‐
Thedetailsoftheproduct.........................................................................‐3‐
Theparametersoftheproduct.................................................................‐7‐
Thefeaturesoftheproduct.......................................................................‐8‐
Accessories List..............................................................................................‐9‐
MachineInformation.......................................................................................‐11‐
Transmitter(TX)........................................................................................‐11‐
Receiver(RX).............................................................................................‐14‐
Useyourequipment........................................................................................‐17‐
Aboveall,preparethetransmitter..........................................................‐17‐
Then,preparethereceiver......................................................................‐18‐
Attheend,setthechanneltothesame.................................................‐18‐
TXchannelschanging..............................................................................‐18‐
RXchannelschanging..............................................................................‐19‐
Tipsforabetterusing......................................................................................‐20‐
Trouble‐shooting.............................................................................................‐22‐
FCCStatement.................................................................................................‐24‐
FCCRadiationExposureStatement.................................................................‐25‐
Cautions!.........................................................................................................‐25‐
Important Information
Please take the time to read this user manual before use the Product, it
contains all notes and important information regarding your wireless HD
video transmission system.
Our limited warranty applies when the products is handled properly for
intended use, in accordance with its operating instruction.
However the warranty may be void in the following cases:
‐2‐
Repairs or product modification have been executed by unauthorized
service personnel.
The damages are caused by accidents including but not limited to,
lighting, exposed to rain or water and moisture.
The model number on the product has been modified or the warranty
tag has been removed
Warnings
This product uses for indoor environment,should not be exposed to
dripping or splashing
Place receiver/transmitter on a flat, hard and stable surface
Ventilation: Do not block the ventilation slots on the
receiver/transmitter or place any heavy object on the top cover
Put the receiver/transmitter in a property ventilated area, away from
direct sunlight or any source of heat.
Water Exposure: To reduce the risk of fire or electric shock, do not
expose the receiver/transmitter to rain or moisture.
Our company has the right to modify this document without any
notice.
Special Notice:
Use of this product in the following locations may result in abnormal
video and audio output(noise, blocked image… etc.)
1. Product installed in the walls made of concrete.
2. Product is situated near the refrigerator or metal fitment.
3. A cluttered room where the wireless signals may be blocked.
This product has been tested and manufactured to comply with each
country’s safety rules. However, there is no guarantee that
interference will not occur in some installation scenario. If the
interference happens, increase the distance between the transmitter
‐3‐
and receiver.
Introduction
This equipment is designed to replace the current widely used cable in the
live broadcasting and production environment, it can be used in film
production, live broadcasting as well as many application which requires
good quality wireless video connection.
The details of the product
The equipment include the series models: SH700M/SH1000M,
600M/1000M and 600M-ENG/1000M-ENG. It is consist of one
transmitter (TX) and one receiver (RX).
‐4‐
1. 600M and 1000M
TX
RX
‐5‐
2. SH700M and SH1000M
TX
RX
‐6‐
4. 600M‐ENGand1000M‐ENG
RX
TX
‐7‐
The parameters of the product
ITEM SPECIFICATION
Frequency 5190，5230，5755 and 5795MHz
Bandwidth 40MHz
Video Formats
Supported
1080p 23.98/24/25/30/50/60
1080psf 23.98/24/25
1080i 50/59.94/60
720p 50/59.94/60
576p 576i 480p 480i
Audio Formats
Supported PCM, DTS-HD, Dolby TrueHD
TransmissionRange 1500ft(Line of sight)
Transmitter
Antenna External Antenna × 2pcs
Transmission Power 24dBm
Functional Interface
HDMI Input; SDI Input; SDI Loop Output; Mini
USB; LEMO Power IN; Antenna RPSMA
Socket; Power ON/OFF
Mounting Structure 1/4” Hot-shoe connection
OLED Display Wireless Channel Info; video status; Battery
info.
Working Voltage 9-18V by DC input, F970 battery
Power Consumption 7-9W
Net Weight(with
antenna) 400g
Dimensions 142.5×76×24.3mm
Temperature -10-50℃(Operating); -40-80℃(Storage)
Receiver
Antenna External Antenna × 5pcs
Receiving Sensitivity -70dBm
‐8‐
Functional Interface
SDI Dual Output; HDMI Output; Mini USB;
LEMO Power IN; Antenna RPSMA Socket;
Power ON/OFF
Locating Structure 1/4” Hot-shoe connection
OLED Display Wireless Channel Info; SDI/HDMI Input Info;
Signal Status; Power Info
Working Voltage 9-18V by DC input, SONY V-mount battery
Power Consumption 7-8W
Net Weight(with
antenna) 800g
Dimensions 169.5×122×25.2mm
Temperature -10-50℃(Operating); -40-80℃(Storage)
*Since the product’s improving process, all the performance, design and specifications
of our products are subject to minor change without prior notice.
The features of the product
Uncompressed 3G/HD/SD-SDI and HDMI, up to 1080p 50/60
Less than 1 frame latency
There is no discernible video delay and you can use it as real time
on-location monitoring.
Operating range: 1500ft (line of sight), the transmission distance
may be different, depend on surroundings, radio wave conditions,
buildings block, etc.
Operating band: 5GHz ISM band
Multicast support
Support one transmitter to multi receivers. User can set channel to
pair both the transmitter and receivers.
Built-in fan
TX side built-in high efficiency ventilation fan with very small noise.
OLED shown in work status
All-Metal Shell
‐9‐
Both transmitter and receiver adapt metal shell which is durable and
solid.
Simple connection
The wireless system is plug-and-play designed, without any software
configuration.
Accessories List
Accessories of all models are subject to the following packing list.
‐10‐
Antenna x 8 Power cable x 2
2-pin Lemo to BTap
SDI Cable x 2 7” Articulating Arm x 1
Hot-shoe Stand x 1
‐11‐
Machine Information
Transmitter(TX)
‐12‐
‐13‐
STRUCTURE
1 OLED Display
Displays information of channel, Video status and battery capacity.
2 UP Button
Channel +
3 DOWN Button
Channel -
4 MENU Button
Unlock the channel and Confirm the Selection
5 Power ON/OFF
Turn ON or OFF the transmitter
6 SDI IN
Connect to SDI Video Source
7 SDI OUT(Loop Through)
Connect to the your monitor or other
8 HDMI IN
Connect to HDMI Video source
9 DC IN(Lemo)
Support 9-18V
10 Antenna Connector x2
Fix antennas
11 Battery Clip
Battery compartment, for F550/F970 battery
‐14‐
Receiver(RX)
‐15‐
‐16‐
STRUCTURE
1 Antenna Connector x5
RPSMA connectors for antennas
2 OLED Display
Displays information of channel, signal strength and battery capacity.
3 MENU Button
Unlock and Confirm the Selection
4 LEFT Button
Channel -
5 RIGHT/DOWN Button
Channel +
6 V+/UP Button
Volume +, not use on this version
7 V-/DOWN Button
Volume -, not use on this version
8 BAT-OUT(B-TAP socket)
Provide DC power supply from the battery for external equipment
9 HDMI OUT
Connect to your HDMI monitor or other
10 SDI OUTx2
Connect to your SDI monitor or other
11 DC IN(Lemo) *Support 9-18V
Support 9-18V
‐17‐
12 Battery Clip
Support V-Mount battery
13 Power ON/OFF
Power on or OFF the receiver
Use your equipment
Above all, prepare the transmitter
1. Connect your SDI or HDMI video source to the “SDI IN”/”HDMI IN”
port of transmitter (when both SDI and HDMI video are inputted to the
‐18‐
transmitter, it will auto select the SDI video for transmission).
2. If need, you can connect the SDI out(loop through) to other equipment
as well
3. Fix the antenna
4. Connect to a “B-TAP” battery by through power cable or insert F970
battery to the transmitter
5. Power on the transmitter
6. Set the Channel
Then, prepare the receiver
1. Connect “SDI OUT”/”HDMI OUT” port of receiver to monitor or other
device.
2. Fix the antenna
3. Connect to a “B-TAP” battery by through power cable or insert V-type
battery to the receiver
4. Power on the Receiver
5. Set the Channel (must set both transmitter and receiver to the same
channel)
6. After 5-10s, the transmission video will be shown on monitor
At the end, set the channel to the same
Both Transmitter and Receiver were set to same channel in Manufactory.
In case, you want to change to a new channel, please follow the below:
Remark:
Both transmitter and receiver must be set to same one
TX channels changing
Step1: Power on the transmitter
‐19‐
Step2: Press “MENU” button until shown in the unlock icon on OLED.
Step3: Press “Up” or “DOWN” button to choose channel, then press
“MENU” to confirm.
Step4: Transmitter channel setting accomplished.
RX channels changing
Step1: Power on the Receiver
Step2: Press “MENU” button until display unlock icon .
Step3: Click Left or Right button to choose channel, then click “MENU” to
confirm.
Step4: Receiver channel setting accomplished.
‐20‐
Tips for a better using
1. Fix the two antennas to the transmitter and arrange them to be a right
angle as below figure to get better performance.
‐21‐
2. On transmitter side, when both SDI and HDMI source are inputted, the
transmitter will automatically select the SDI source
3. Fix the five antennas to receiver and arrange them to a right angle as
figure to get better performance.
4. Set the receiver higher will enhance the transmission distance.
‐22‐
Trouble-shooting
If the receiver failed to output the video correctly, the possible causes are
as below, please find the solution from following chart:
TROUBLES&POSSIBLEREASONS:SOLUTON:
OSD Information on TV
Displaying “Waiting for connection…” for a long time
Transmitter is not powered up. Power on the transmitter.
Transmitter or receiver is not placed
correctly.
Place the TX or RX correctly.
The transmitter and receiver are too
far away.
Move the receiver closer to the
transmitter.
Several solid wall partition on TX and
RX.
Reduce the number of solid walls
between TX and RX.
There are so many obstacles between
TX and RX.
Move the receiver closer to the
transmitter.
Other transmitter is working on the
same or adjacent channel.
Turn off other transmitter, or change
channel.
No Video Signal received
Transmitter and video source are not
connected.
Connect the transmitter to video source
by SDI/HDMI cable.
The video source is turned OFF Power ON the video source.
Bad contact of cable of transmitter. Remove and then re-plug the transmitter
Abnormal working of transmitter Reboot the transmitter
Problem with cable between TX and
video source
Change the SDI/HDMI cable
Player NOT support the output
resolution format.
Switch the output video resolution to
other modes.
‐23‐
The TV/Monitor NOT support HDCP
authentication
Replaced with HDCP-certified
TV/Monitor.
Image
No signal input to Receiver or TV/Monitor
Receiver is turned OFF Power on receiver.
Receiver and TV are not connected. Connect receiver and TV/Monitor via
SDI/HDMI input.
TV/Monitor NOT switched to
SDI/HDMI input.
Switch TV/Monitor to SDI/HDMI input.
Bad contact of the cable of receiver or
TV/Monitor.
Remove then re-plug the SDI/HDMI
cable.
TV/Monitor turn into standby mode. Switch the TV/Monitor to normal
operation mode.
Abnormal working of receiver. Reboot the receiver.
No image appear on TV/Monitor
Bad contact of receiver or cable. Re-plug the cable of the receiver or
TV/Monitor.
Abnormal working of receiver. Reboot the receiver.
Receiver failure. Please contact your retailer.
Abnormal color on TV screen
Bad contact of cable of receiver or
TV/Monitor.
Unplug and then plug the HDMI cable of
the receiver or TV.
Bad contact of cable of transmitter or
video source.
Unplug and then plug the HDMI cable of
the TX and player.
Abnormal working of transmitter or
receiver.
Reboot the transmitter and receiver.
‐24‐
FCC Statement
This equipment complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures: -Reorient or
relocate the receiving antenna. Increase the separation between the
equipment and receiver. Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected. Consult the dealer or
an experienced radio/TV technician for help. To assure continued
compliance, any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment. (Example use only shielded interface cables when
connecting to computer or peripheral devices
‐25‐
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment .This equipment should be installed and
operated with minimum distance 20cm between the radiator& your body
Cautions!
The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Such
modifications could void the user authority to operate the equipment.