ShenZhen Zhongherong Electric Technology SZESKY001 Remote Control Toy Transmitter User Manual II

ShenZhen Zhongherong Electric Technology Co., Ltd. Remote Control Toy Transmitter II

Contents

User Manual II

The rudder stick operation for Model 2 is the same as Model 1 When the elevator stick is pushed backward,the nose of the helicopter will tilt upward,then the helicopter moves backward andits speed increases. ADJUSTMENTS BEFORE FLYINGThe meso-position of each operating stick, aileron and rudder had already set in the factory, you can adjust it according to your needs. If need adjustment ,you can adjust according to your remote products.If you are a novice ,please connect and adjust each part according to the corresponding manual and pictures to ensure the proper operation.Caution2.4G2.4G TRANSMITTER INSTRUCTION MANUAL102.4G Remote control system adopts Advanced Spread Spectrum Technology and digital FSK (frequency shift key) Coding Technology.
NORIDEL UPTHREndpoint Output Value123HL0%50%100%PIT Output Value123HL0%50%100%123HLTHR Output Value0%50%100%123HLPIT Output Value0%50%100%Throttle/pitch curve diagram/Hovering Pitch knob1 2 3 HL 1 2 3 HL0%50%100%0%50%100%Output Value Output Value3DThe hovering pitch knob function is to shift the center point of curve either upward or downward to adjust totor RPM at the hover position. NOR Pitch 3D PitchEndpoint Endpoint Endpoint Endpoint Endpoint 2.4G2.4G TRANSMITTER INSTRUCTION MANUAL2.4G Remote control system adopts Advanced Spread Spectrum Technology and digital FSK (frequency shift key) Coding Technology. 14
PITCH TRIM KNOBPITCH 0PointOutput Value123HL0%50%100%The pitch trim knob is a trimmer for the pitch channel .This knob should be set to at first ,then adjust the rotor RPM by shifting it upward or downward. As the setting of each manufacturer is different ,only small trim adjustment will be required if the pitch curve had set properly.Before any adjustment, please set all the switches in the front of the transmitter to the lowest(normal)position.Turn on the power switch of the transmitter and the receiver , then make the following adjustments:THRELEAIL RUDAIL : ELE: THR: RUD:REV: NOR: Channel displayAIL : Aileron(channel 1)ELE: Elevator(channel 2)THR: Throttle(channel 3)RUD: Rudder servo(channel 4)Rudder operating displayREV: ReverseNOR: NormalCheck the direction of each servo, If a servo operates in the wrong direction, switch its SERVO REVERSR switch (the direction of operation can be changed without changing the linkage.) 2.Check the aileron, elevator and rudder neutral adjustment, if the neutral position changed,please reset and readjust it ,make the servo horn to be perpendicar to the servo.3.Check to see whether the operation of each direction is normal, if not ,please adjust the SERVE REVERSERswitch (For 6CH transmitter ).2.4G2.4G TRANSMITTER INSTRUCTION MANUAL15 2.4G Remote control system adopts Advanced Spread Spectrum Technology and digital FSK (frequency shift key) Coding Technology.
45 4. At last, check the range curve of each servo direction, turn the servo horn rod outward if the range is too small and turn it inward while the range is too large.5. After finishing all the connections, recheck the operating direction and setting etc.Please charge with an adapter, overcharge or overheating may causeburn or fire etc. or combustion. Please charge Ni-CD/Ni-MH battery with original TWF changer or quick charger, and power off the chargerin time after finishing the charging .2.4G2.4G TRANSMITTER INSTRUCTION MANUAL162.4G Remote control system adopts Advanced Spread Spectrum Technology and digital FSK (frequency shift key) Coding Technology.
Always be sure that the batteries are loaded in the correct polarity order. If the batteries are loaded incorrectly, the transmitter will be unworkable .Please take the battery out during the suspended period, please clean it with dry cloth if there is some liquid leaking out from the battery.When the green lamp of the battery voltage indicator(LED) goes off or the Red LED flashes, please exchange the batteries or charge them immediately. +-LED)2.4G2.4G TRANSMITTER INSTRUCTION MANUAL182.4G Remote control system adopts Advanced Spread Spectrum Technology and digital FSK (frequency shift key) Coding Technology.
TRAINER2.4G2.4G TRANSMITTER INSTRUCTION MANUAL19 2.4G Remote control system adopts Advanced Spread Spectrum Technology and digital FSK (frequency shift key) Coding Technology.
The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. In cases where the manual is provided only in a form other than paper, such as on a computer disk or over the Internet, the information required by this section may be included in the manual in that alternative form, provided the user can reasonably be expected to have the capability to access information in that form. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.

Navigation menu