Shin Chuan Computer SC800PDT-BW Portable Data Terminal User Manual Manual
Shin Chuan Computer Co., Ltd. Portable Data Terminal Manual
Manual
SC800 / SC820 User’s Manual
WinCE. NET Rugged Portable Data Terminal
Mar/10/2008 Ver: 0.2
Table of Contents
Chapter 1.Introduction............................................................................ 1-1
1.1 About this Manual........................................................................... 1-1
1.2 User and Product Safety.................................................................. 1-2
1.3 Battery Safety.................................................................................. 1-3
1.4 CE Statement................................................................................... 1-4
1.5 FCC Statement ................................................................................ 1-8
1.6 Recycling & disposal instructions. ................................................. 1-9
1.7 Regulatory information................................................................... 1-9
1.8 Product Labeling........................................................................... 1-10
1.9 System Specifications ................................................................... 1-14
1.10 Environment Standard................................................................. 1-16
1.11 Warranty and after service........................................................... 1-16
Chapter 2.Getting Started........................................................................ 2-1
2.1 Check the package .......................................................................... 2-1
2.2 General View of the PDT................................................................ 2-3
2.2.1 SC800 general view ............................................................... 2-3
2.2.2 SC820 general view ............................................................... 2-5
2.3 Charging the Battery Pack .............................................................. 2-7
2.3.1 Installing the battery pack...................................................... 2-7
2.3.2 Charging the battery pack with Power Adapter ..................... 2-9
2.4. Handling the PDT ........................................................................ 2-10
2.4.1 Starting the PDT................................................................... 2-10
2.4.2 Power on / off....................................................................... 2-10
2.4.3 Calibration of the touch Screen.............................................2-11
2.4.4 To mute the Sound for SC800...............................................2-11
2.4.5 Adjusting the Sound for SC820 ............................................2-11
2.4.6 Using the Stylus ................................................................... 2-12
2.4.7 Using the SC800 Keypad..................................................... 2-12
2.4.8 Using the SC820 Keypad..................................................... 2-14
2.4.9 Using the Ear/Microphone................................................... 2-17
2.5 Navigating the Display ................................................................. 2-18
2.5.1 Setting Time and Date.......................................................... 2-18
2.5.2 Entering the Data ................................................................. 2-18
2.5.3 The Command Bar............................................................... 2-19
2.5.4 The Task Bar ........................................................................ 2-19
2.5.5 The Soft Keypad .................................................................. 2-20
2.5.6 Setting Up Wireless LAN .................................................... 2-20
2.5.7 Reading barcodes, 1D laser version..................................... 2-25
2.5.8 Help...................................................................................... 2-26
2.6 Power management....................................................................... 2-27
2.6.1 Suspend Mode...................................................................... 2-27
2.6.2 Resuming ............................................................................. 2-28
2.7 Resetting the PDT......................................................................... 2-28
2.7.1 Software (Warm) Reset........................................................ 2-28
2.7.2 Cold Reset............................................................................ 2-28
Chapter 3.Setting..................................................................................... 3-1
3.1 Introduction..................................................................................... 3-1
3.2 Control Panel .................................................................................. 3-1
3.2.1 BarCode Setting..................................................................... 3-2
3.2.2 Symbologies List ................................................................... 3-8
3.2.3 Bluetooth Device Properties ................................................ 3-24
3.2.4 Certificates ........................................................................... 3-28
3.2.5 Control Center...................................................................... 3-30
3.2.6 Date/Time............................................................................. 3-34
3.2.7 Dialing Properties ................................................................ 3-34
3.2.8 Display Properties................................................................ 3-36
3.2.9 Input Panel ........................................................................... 3-37
3.2.10 Internet Options ................................................................. 3-38
3.2.11 Keyboard............................................................................ 3-40
3.2.12 Network and Dial-up Connections..................................... 3-41
3.2.13 Owner................................................................................. 3-45
3.2.14 Password ............................................................................ 3-46
3.2.15 PC Connection ................................................................... 3-47
3.2.16 Power ................................................................................. 3-48
3.2.17 Regional Settings ............................................................... 3-50
3.2.18 Remove Programs.............................................................. 3-51
3.2.19 Storage Manager ................................................................ 3-52
3.2.20 Stylus.................................................................................. 3-53
3.2.21 System................................................................................ 3-54
3.2.22 Volume & Sounds Properties ............................................. 3-56
3.3 Taskbar and Start Menu ................................................................ 3-57
Chapter 4.Communication...................................................................... 4-1
4.1 Installing & Setting Up Microsoft ActiveSync............................... 4-1
4.1.1 Installing Microsoft ActiveSync on the Host PC................... 4-1
4.1.2 Connecting PDT to Host PC.................................................. 4-1
4.2 Using ActiveSync............................................................................ 4-1
4.2.1 Setting up a Partnership ......................................................... 4-1
4.2.2 ActiveSync File Synchronization........................................... 4-3
4.3 Networking ..................................................................................... 4-3
Chapter 5.Software Applications ............................................................ 5-1
5.1 Introduction..................................................................................... 5-1
5.2 Software Applications..................................................................... 5-1
5.2.1 Inbox ...................................................................................... 5-1
5.2.2 Internet Explorer .................................................................. 5-10
5.2.3 Media Player ........................................................................ 5-13
5.2.4 Messenger ............................................................................ 5-13
5.2.5 Microsoft WordPad .............................................................. 5-13
5.2.6 Remote Connection.............................................................. 5-19
5.2.7 Windows Explorer ............................................................... 5-20
5.3 DiskOnChip .................................................................................. 5-22
5.3.1 Saving to Flash..................................................................... 5-22
5.3.2 DiskOnChip Location .......................................................... 5-22
5.3.3 DiskOnChip Size ................................................................. 5-23
1-1
Chapter 1. Introduction
Congratulations on purchasing the SC800/SC820 Portable Data Terminal (PDT), a
Microsoft Windows®CE .Net rugged PDT. Its special combination of features makes it
perfect for using in a wide range of applications. These features as:
Intel® XScaleTM PXA270 520MHz 32 bits RISC Processor
Windows® CE .NET 5.0 Operating System
128 MB SDRAM & 128 MB Flash ROM
Open Architecture: User Accessible SD Slot
240 x 320, 3.5” Color TFT Display with Touch Panel
One Numeric-Alpha Keyboards with LED backlight
802.11b/g Radio Support (Bluetooth Optional)
Integrated 1D Barcode Scanner
Changeable Keypad
1.1 About this Manual
The following chapters contained in this manual are:
Chapter 1: Introduction General information about the PDT.
Chapter 2: Getting started Describe the basic use of the PDT.
Chapter 3: Setting Provide basic instructions for customizing the
PDT.
Chapter 4: Communication Describe how to use all kinds of communication
of the PDT.
Chapter 5: Software Application Describe the installed applications on the PDT.
1-2
1.2 User and Product Safety
z Do not stare into the laser or LED beam directly or shine it into eyes.
z Never use strong pressure onto the screen or subject it to severe impact, as the
LCD panel could become cracked and possibility cause personal injury. If the
LCD panel is broken, never touch the liquid inside because the liquid irritates the
skin.
z Although the PDT has passed the test of IP65 standard for water and dust
resistance, avoid prolonged exposure to rain or other concentrated moisture.
Such condition exceeds the IP65 standard, and could result in water or other
contaminants entering into the PDT.
z Use only the original approved AC Adapter with the PDT. Use of an unapproved
AC Adapter could result in electrical problems, or even cause a fire or electrical
shock to the user.
z Do not disassemble the PDT. Servicing should be done by supplier only. If the
PDT or accessories gets damaged due to wrong handling or unauthorized repair,
warranty is void. In case the warranty seals are broken, warranty is void too.
z Make regularly back-ups of all important data.
z Under no circumstance will supplier be liable for any direct, indirect,
consequential or incidental damages baring out of the use or inability to use the
hardware and software and/or any data loss, even if supplier has been informed
about the possibility of such damages.
z LASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER
PRODUCT
1-3
1.3 Battery Safety
CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of
Used Batteries According to the Instructions.
Lithium-ion battery packs might get hot, explode, ignite and/or cause serious injury if
exploded by abusive using. Please follow the safety warnings listed as below:
z Do not throw the battery pack in fire. Do not expose the battery to high
temperatures.
z Do not connect the positive battery pack with negative battery pack to each other
with any metal object (like wire).
z Do not carry or store battery pack together with metal objects.
z Do not pierce the battery pack with nails or drills, strike the battery pack with a
hammer, step on the battery pack or otherwise expose it to strong impacts,
shocks or excessive force.
z Do not solder onto the battery pack.
z Do not expose battery pack to liquid or allow the battery contacts to get wet.
z Do not disassemble or modify the battery pack. The battery pack contains safety
and protection measures, which, if damaged, may cause the battery pack to
generate heat, explode or ignite.
z Do not discharge the battery pack using any device except for the specified
device. When it is used in devices other than the specified devices, the battery
pack can be damaged or its life expectancy reduced. If the device causes any
abnormal current to flow, it may cause the battery pack to become hot, explode
or ignite and cause serious injury.
z In the event the battery pack leaks and the fluid gets into one’s eye, do not rub
the eye. Rinse well with water and immediately seek medical care. If left
untreated, the battery fluid could cause damage to the eye.
1-4
1.4 CE Statement
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive
1999/5/EC. The following test methods have been applied in order to prove
presumption of conformity with the essential requirements of the R&TTE Directive
1999/5/EC:
- EN 60950-1: 2006
Safety of Information Technology Equipment
- EN50360 : (2001-07)
- Product standard to demonstrate the compliance of mobile phones with the basic
restrictions related to human exposure to electromagnetic fields (300 MHz-3GHz)
- EN50361 : (2001-07)
- Basic standard for the measurement of specific absorption rate related to human
exposure to electromagnetic fields from mobile phones (300 MHz-3 GHz)
-
- EN50371 : (2002-03)
- Generic standard to demonstrate the compliance of low power electronic and
electrical apparatus with the basic restrictions related to human exposure to
electromagnetic fields (10 MHz-300 GHz) -- General public
- EN 300 328 V1.7.1: (2006-10)
- Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband
Transmission systems; Data transmission equipment operating in the 2,4 GHz
ISM band and using spread spectrum modulation techniques; Harmonized EN
covering essential requirements under article 3.2 of the R&TTE Directive
- EN 301 511 V9.0.2: (2003-03)
- Global System for Mobile communications (GSM); Harmonized standard for
mobile stations in the GSM 900 and DCS 1800 bands covering essential
requirements under article 3.2 of the R&TTE directive (1999/5/EC)
- EN 301 489-1 V1.6.1: (2005-09)
1-5
- Electromagnetic compatibility and Radio Spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services;
Part 1: Common technical requirements
- EN 301 489-17 V1.2.1 (2002-08)
- Electromagnetic compatibility and Radio spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services;
Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5
GHz high performance RLAN equipment
- EN 301 489-7 V1.2.1: (2002-08)
ElectroMagnetic compatibility and Radio spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment ad services;
Part 7: Specific conditions for mobile and portable radio and ancillary equipment
of digital cellular radio telecommunications systems (GSM and DCS)
This device is a 2.4 GHz wideband transmission system (transceiver), intended for use
in all EU member states and EFTA countries, except in France and Italy where
restrictive use applies.
In Italy the end-user should apply for a license at the national spectrum authorities in
order to obtain authorization to use the device for setting up outdoor radio links and/or
for supplying public access to telecommunications and/or network services.
This device may not be used for setting up outdoor radio links in France and in some
areas the RF output power may be limited to 10 mW EIRP in the frequency range of
2454 – 2483.5 MHz. For detailed information the end-user should contact the national
spectrum authority in France.
0560
Česky
[Czech]
[Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se
základními požadavky a dalšími příslušnými ustanoveními směrnice
1999/5/ES.
Dansk
[Danish]
Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr
[udstyrets typebetegnelse] overholder de væsentlige krav og øvrige
relevante krav i direktiv 1999/5/EF.
1-6
Deutsch
[German]
Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp]
in Übereinstimmung mit den grundlegenden Anforderungen und den
übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Eesti
[Estonian]
Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme
[seadme tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ
põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele
sätetele.
English Hereby, [name of manufacturer], declares that this [type of equipment] is
in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente [nombre del fabricante] declara que el [clase de
equipo] cumple con los requisitos esenciales y cualesquiera otras
disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Ελληνική
[Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of
equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ
ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ
ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Français
[French]
Par la présente [nom du fabricant] déclare que l'appareil [type
d'appareil] est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 1999/5/CE.
Italiano
[Italian]
Con la presente [nome del costruttore] dichiara che questo [tipo di
apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski
[Latvian]
Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka
[type of equipment / iekārtas tips] atbilst Direktīvas 1999/5/EK
būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių
[Lithuanian]
Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka
esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Nederlands
[Dutch]
Hierbij verklaart [naam van de fabrikant] dat het toestel [type van
toestel] in overeenstemming is met de essentiële eisen en de andere
relevante bepalingen van richtlijn 1999/5/EG.
Malti
[Maltese]
Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott]
jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti
li hemm fid-Dirrettiva 1999/5/EC.
Magyar
[Hungarian]
Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a
vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb
1-7
elõírásainak.
Polski
[Polish]
Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest
zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi
postanowieniami Dyrektywy 1999/5/EC.
Português
[Portuguese]
[Nome do fabricante] declara que este [tipo de equipamento] está
conforme com os requisitos essenciais e outras disposições da Directiva
1999/5/CE.
Slovensko
[Slovenian]
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi
zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.
Slovensky
[Slovak]
[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné
požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.
Suomi
[Finnish]
[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment =
laitteen tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY
oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen
mukainen.
Svenska
[Swedish]
Härmed intygar [företag] att denna [utrustningstyp] står I
överensstämmelse med de väsentliga egenskapskrav och övriga relevanta
bestämmelser som framgår av direktiv 1999/5/EG.
1-8
1.5 FCC Statement
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation. Complies with 21 CFR 1040.10 and 1040.11 except for
deviations pursuant to Laser Notice No. 50, dated June 24, 2007.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating instructions
for satisfying RF exposure compliance. To maintain compliance with FCC RF
exposure compliance requirements, please follow operation instruction as documented
in this manual.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
The availability of some specific channels and/or operational frequency bands are
1-9
country dependent and are firmware programmed at the factory to match the intended
destination. The firmware setting is not accessible by the end user.
Caution: SCC declares that SC800 ( FCC ID: TQ2-SC800PDT-BW ) / SC820
( FCC ID: TQ2-SC800PDT-BW ) is limited in CH1~CH11 for 2.4GHz by
specified firmware controlled in U.S.A.
The FCC ID of SC800/SC820 is TQ2-SC800PDT-BW
LED AND LASER SAFETY INFORMATION
z Class II LED/Laser Product
z Do not stare at the LED/Laser or shine into eyes
z Do not allow young children to use the product without adult supervision
z Do not replace/repair the LED/Laser, these are not user replaceable
z Do not shine the LED/Laser on a shiny reflective surface
z LASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER
PRODUCT
1.6 Recycling & disposal instructions.
Do not throw this product in the home waste bin. For proper end-of-life
treatment consult the
Environmental care section of ftp://ftp.sccltd.com.tw/
1.7 Regulatory information.
For CE, FCC, RoHS and other Document of Conformities, consult the
Regulatory section of ftp://ftp.sccltd.com.tw
1-10
1.8 Product Labeling
The PDT has several labels as showed in Figure 1-1 to 1-4.
A. SC800
Figure 1-1 Product Labeling (Front side view)
Label nr. Description
1 LCD panel protection film
2 SC800 logo
3 Warranty seal PDT
Table 1-1 Front labeling
1-11
Figure 1-2 Product Labeling (Back side view)
Label nr. Description
4 Laser radiation warning label
5 Serial / Configuration number
6 PenPower label (only use on Simplified
Chinese version)
7 CCC label (only use with China)
8 System and regulatory label
9 NCC label (only use on Traditional Chinese
version)
10 RoHS Use Life Label for China
11 Windows CE .NET label
Table 1-2 Rear labeling
1-12
B. SC820
Figure 1-3 Product Labeling (Front side view)
Label nr. Description
1 LCD panel protection film
2 SC820 logo
3 Warranty seal PDT
Table 1-3 Front labeling
1-13
Figure 1-4 Product Labeling (Back side view)
Label nr. Description
4 LED/Laser radiation warning label
5 Serial / Configuration number
6 PenPower label (only use on Simplified
Chinese version)
7 CCC label (only use with China)
8 System and regulatory label
9 NCC label (only use on Traditional Chinese
version)
10 RoHS Use Life Label for China
11 Windows CE .NET label
Table 1-4 Rear labeling
1-14
1.9 System Specifications
The SC800 / SC820 detailed specifications as follows. Unless otherwise noted, all the
specifications are subject to change without prior notification.
Table 1-5 System Specification
SC800 / SC820
Processor - Intel PXA270 520MHz 32 bits RISC CPU
Memory - 128MB Flash ROM
- 128MB SDRAM
Display - 240 x 320 3.5” TFT 256K Color LCD with LED
backlight
Audio
- One mono speaker for system voice (on lower case)
- One 2.5 mm Ø stereo earphone jack with mono mike
input
- One internal MIC
- One Receiver
Expansion Slot - One SD/MMC slot (only support SD memory)
- One SIM slot for WAN module
LED - One Dual-Color LED for Charger Indicator
- One Dual-Color LED for Scanner Indicator
Radio Support
- Wireless LAN: 802.11b/g
- Bluetooth: Class II
- IrDA: 1.2
Scan Engine - Symbol, Opticon Laser (1D) Engine. (optional)
Communication Ports
- USB: Support USB v1.1 both host and client.
(PDT and Cradle)
- Serial: RS232 via optional cable or Cradle.
Power System
- Standard Li-Ion Battery Pack, 3.7V, 2200mAh
- Advanced Smart Battery with Gas-Gauge
- Built-in Battery Charger
- 4.2V/70mAh rechargeable backup battery
- One Battery Cover Sensor Switch
- Power Adapter: 100~240V AC, 50/60Hz Input ;
5VDC/2.6A Output
1-15
SC800 / SC820
SC800
- One Power Button
- One Reset Button
- Three Barcode Scanner Buttons
- Two Navigation Buttons
- Four Application Buttons
- One 18-key Numeric Keypad
- One Reserved Button
Keypad / Buttons
SC820
- One Power Button
- One Reset Button
- Three Barcode Scanner Buttons
- Two Navigation Buttons
- Four Application Buttons
- One 33-key Alpha-Numeric Keypad
- One Reserved Button
Dimensions and
Weight
- Dimensions:
L: 155mm, W: 82mm, H: 31~33mm
- Weight: 400g with Standard Battery Pack
Color - Black
Peripherals and
Accessories
- Optional: RS232 Serial Cable for Terminal / USB
Host Cable for Terminal / High-Capacity Li-Ion
Battery Pack (3.7V, 4000 mAh) / Single Dock / 4 Slot
Battery Charger / Car Adapter / RS232 Cable / Pistol
Grip
Software - Microsoft Windows CE.NET 5.0 Professional
1-16
1.10 Environment Standard
Table 1-6 Environment Standards
Operating Temperature 14oF ~ 122oF( -10oC ~ 50oC)
Storage Temperature -4oF ~ 158oF (-20oC ~ 60oC)
Humidity 5% ~ 95% (non-condensing)
Drop 5ft (1.5m) Drop onto Concrete
Water & Dust proof IP65 Certificated
Vibration MIL STD 810F
1.11 Warranty and after service
Should this PDT be malfunctioned, please contact your original retailer providing
information about the product name, the serial number, and the details about the
problem.
2-1
Chapter 2. Getting Started
2.1 Check the package
Open the package and check all the parts are inside without shortage and damage:
A. SC800
Figure 2-1 Inside the package
1. SC800 Terminal
2. Standard Battery Pack (3.7V, 2200 mAh)
3. USB Client Cable for Terminal
4. AC Power Cord
5. Standard AC Adapter 5VDC/2.6A
6. Earphone/ Microphone Set
7. Quick Guide (not shown in the picture)
2-2
B. SC820
Figure 2-2 Inside the package
1. SC820 Terminal
2. Standard Battery Pack (3.7V, 2200 mAh)
3. USB Client Cable for Terminal
4. AC Power Cord
5. Standard AC Adapter 5VDC/2.6A
6. Earphone/ Microphone Set
7. Quick Guide (not shown in the picture)
2-3
2.2 General View of the PDT
2.2.1 SC800 general view
Figure 2-3 SC800 front side view
Figure 2-4 SC800 back side view
2-4
Table 2-1 Description of SC800 General View
“Red” color Reading barcode 1 Scanner LED Indicator
“Green” color Successful reading
“Red” color Charging battery 2 Charge LED Indicator
“Green” color Battery charged full
3 LCM / Touch Panel Do specific action through touch panel by stylus
4 Left Scan key
Right Scan key
Scan key
Start scanning the barcode by pressing any one of
these three scan keys
5 Power key Puts the terminal into and wakes the terminal from
suspend mode.
6 F1 ~ F4 key The four application keys, hot keys of application
program defined by end user.
7 Navigation key Navigation keys for left, right, up and down
directions
8 Alpha-Numeric keys Numeric keys, Change to Alpha keys after pressing
Alpha key.
9 Alpha key Toggle Alpha-mode for Alpha-Numeric keys
10 Fn key This key is used in combination with other keys to
type special characters and perform system functions.
11 Enter key This key confirms data entry
12 Earphone Jack
Connector
A connector to plug a earphone
13 USB / Serial /
Synchronization port
A connector to support USB Host/Client and serial
functions
14 Scan window A window for scanning of barcode reader
15 Stylus Use the stylus for selecting items and entering
information.
16 Battery Cover Protect Battery pack, keep the switch of battery cover
to leave system from suspend mode
17 Battery cover Latch To keep Battery Cover locked
18 Hand Strap This strap can be sealed tighter or looser
19 Speaker 1W speaker for audio sound
20 DC Power Jack A connector to support AC power.
21 IrDA A connector to support IrDA functions
2-5
2.2.2 SC820 general view
Figure 2-5 SC820 front side view
Figure 2-6 SC820 back side view
2-6
Table 2-2 Description of SC820 General View
“Red” color Reading barcode 1 Scanner LED Indicator
“Green” color Successful reading
“Red” color Charging battery 2 Charge LED Indicator
“Green” color Battery charged full
3 LCM / Touch Panel Do specific action through touch panel by stylus
4 Left Scan key
Right Scan key
Scan key
Start scanning the barcode by pressing any one of
these three scan keys
5 Power key Puts the terminal into and wakes the terminal from
suspend mode.
6 F1 ~ F4 key The four application keys, hot keys of application
program defined by end user.
7 Navigation key Navigation keys for left, right, up and down
directions
8 Alpha keys Alpha key.
9 Numeric keys Numeric keys.
10 Fn key This key is used in combination with other keys to
type special characters and perform system functions.
11 Enter key This key confirms data entry
12 Earphone Jack
Connector
A connector to plug a earphone
13 USB / Serial /
Synchronization port
A connector to support USB Host/Client and serial
functions
14 Scan window A window for scanning of barcode reader
15 Stylus Use the stylus for selecting items and entering
information.
16 Battery Cover Protect Battery pack, keep the switch of battery cover
to leave system from suspend mode
17 Battery cover Latch To keep Battery Cover locked
18 Hand Strap This strap can be sealed tighter or looser
19 Speaker 1W speaker for audio sound
20 DC Power Jack A connector to support AC power.
21 IrDA A connector to support IrDA functions
2-7
2.3 Charging the Battery Pack
Before using the PDT, perform the basic procedure of charging the battery pack
through the following steps.
2.3.1 Installing the battery pack
1. On the PDT attached with a hand-strap, detach and loose the hand-strap.
Figure 2-7 Release the Hand strap from PDT
2. Turn the locking screws (right and left) downwards and lift the battery cover away
from the PDT.
Figure 2-8 Detach the battery cover from PDT
2-8
3. Insert the battery pack into the battery compartment with the label facing out, and
ensuring the battery snaps into place.
Figure 2-9 Insert the battery pack
4. Replace the battery cover by inserting the top first, and then press the bottom in firmly.
Turn the locking screws (right and left) upwards to secure the cover to the PDT.
Figure 2-10 Replace the battery cover
5. Charge time. For the first time to charge the battery pack needs approximately 6
hours. Subsequent charging time needs approximately 4 hours.
2-9
◆. When charging the battery pack, the charge LED indicator on the PDT turns on
Red. After the battery pack is fully charged, the charge LED indicator turns to
Green.
2.3.2 Charging the battery pack with Power Adapter
1. Connect the Power cord to the Power adapter.
2. Plug in the connector of the power adapter.
3. Connect the power cord to a power source.
Figure 2-11 Charging with power adapter
◆ When charging the battery pack, the charge LED indicator on the PDT turns on
Red.
◆ After the battery pack is fully charged, the charge LED indicator turns to Green.
2-10
2.4. Handling the PDT
2.4.1 Starting the PDT
Press the Power key to turn on/off the PDT. If the PDT does not power on, perform a
cold boot. See 2-7 Resetting the PDT.
CAUTION: When a battery is fully inserted in PDT for the first time, upon the
PDT’s first power up, the device boots and powers on automatically.
Figure 2-13 Starting the PDT
2.4.2 Power on / off
¾ To turn on the PDT
Press the Power key briefly ( ). If the PDT does not power on, perform the cold
reset. See chapter 2.7.1.
As the PDT initializes its file system, it splash screen displays for about 30 seconds
followed by calibration screen. Every time you perform a cold reset, these screens will
also appear.
To turn off the PDT, just press the Power key again. This action does not actually turn off
the PDT, it only turns the PDT into suspend mode. All running applications remain as you
left them, until you press the Power key again to resume operation of the PDT
When the PDT is powered on for the first time,
it initializes its system. A splash screen (figure
2-13) appears for a short period of time
followed by the Wince.NET 5.0 window.
This section offers the basic procedures of PDT
using.
2-11
2.4.3 Calibration of the touch Screen
On the initial boot-up of the PDT, the stylus
calibration screen (Labeled Align Screen)
opens. Use the stylus to press and hold
briefly on the center of each target as it
moves around the screen.
If necessary, adjust the backlight on the PDT
to make the screen readable. (See below
2.4.4. Adjust the brightness).
When you feel the touch screen function is
poor or the operation does not match the
exact location it should be, please recalibrate
the screen by using the stylus to tap the
Start > Settings > Control Panel > Stylus,
to open the “Calibration” to recalibrate
again.
Figure 2-14 Calibration
2.4.4 To mute the Sound for SC800
To mute the sound, press the key first, and then press the key to turn off
and on of the sound.
2.4.5 Adjusting the Sound for SC820
The factory default for the sound is in Middle level. You can adjust the sound to meet
your environment and comfort as:
1) Become low voice: Press the key and then press the key to become low
voice.
2) Become high voice: Press the key and then press the key to become
high voice.
2-12
2.4.6 Using the Stylus
The stylus is located next to hand-strap on the left rear of the PDT. The stylus function
is same as the mouse on a PC. Use the stylus to:
1) Navigate the display, select menu item and open optional applications.
2) Tap the characters on soft keyboard panel.
3) Hold the stylus on the screen and drag across the screen to select the list of multiple items.
CAUTION: Never use a pen, pencil, or other sharp object on the display to avoid any
unexpected damage of the touch screen.
2.4.7 Using the SC800 Keypad
Figure 2-15 SC800 Keypad
Table 2-3 Keypad List
Key Main Function Fn + Main Function Alpha + Main
Function
BarCode Start
Power On/Off
Internet Explorer
2-13
Key Main Function Fn + Main Function Alpha + Main
Function
Microsoft WordPad
Inbox
File Explorer
Up Left
Down Right
TAB (Tabulation) ESC
Caps Audio Mute
Function change
Change to letters
Backspace
1 ＠ (at) ： ＼
2 ’ (Quotation Marks) Ａ Ｂ Ｃ
3 ＋ (Plus Sign) Ｄ Ｅ Ｆ
4 Paste Ｇ Ｈ Ｉ
5 Del (Delete) Ｊ Ｋ Ｌ
6 － (Minus Sign) Ｍ Ｎ Ｏ
7 Copy Ｐ Ｑ Ｒ
Ｓ
8 ＆ (AND) Ｔ Ｕ Ｖ
9 X (Multiplication) Ｗ Ｘ Ｙ
Ｚ
0 Space 〔 〕
＊ (Asterisk) Start Menu . (Point) ， ；
＃ ／ (Division) ＝ ％
Enter
Table 2-4 Special Assembler Key
Assembler Key Functionality Definition
Warm Reset Press “Reset” button in the back.
Cold Reset Press “Power” and “Reset” button
simultaneously.
2-14
2.4.8 Using the SC820 Keypad
Figure 2-16 SC820 Keypad
Table 2-5 Keypad List
Key Main Function Fn + Main Function
Main Barcode Scan
Key
Power On/Off
Internet Explorer F5
Microsoft WordPad F6
Inbox F7
File Explorer F8
Up Left
Down Right
Esc
Tab
Backspace Del
Caps Start Menu
2-15
Key Main Function Fn + Main Function
Enter
Function change
Space
A ~
B $
C +
D 1
E 2
F 3
G !
H %
I － (Minus Sign)
J 4
K 5
L 6
M Copy
N @
O \
2-16
Key Main Function Fn + Main Function
P ＊
Q 7
R 8
S 9
T Paste
U #
V &
W /
X . (Point)
Y 0
Z =
Table 2-6 Special Assembler Key
Assembler Key Functionality Definition
Warm Reset Press “Reset” button in the back.
Cold Reset Press “Power” and “Reset” button
simultaneously.
2-17
2.4.9 Using the Ear/Microphone
Connect Ear/Microphone to PDT earphone jack connector. The PDT is not built in
microphone; if you like to record the voice, you have to use Ear/Microphone.
Figure 2-17 Ear/Microphone
2-18
2.5 Navigating the Display
2.5.1 Setting Time and Date
In the Date/Time options, you can change the year, month, date, time, time zone, or
select automatic adjust for Daylight Saving Time. To set or change the date and time:
1. Select Start > Settings > Control Panel >
Date/Time
2. To change the year, select the year or open a
numeric dial. Select the up arrow to increase
the value; select the down arrow to decrease
the value. Or you can type a new value in
the field.
3. Select the month to open a pull-down list of
months or press the arrow buttons to either
side of the month to increase or decrease the
month.
Figure 2-18 Date/Time properties
4. To change the time, select the hour, minute, seconds, or AM/PM and select the up
arrow to increase the value; select /tape the down arrow to decrease the value. Or
you can type a new value in the field.
5. Select your correct time zone from the pull-down list.
6. To automatically adjust the clock for Daylight Saving Time, enable the checkbox
at the bottom of the screen.
7. Select Apply to make save your changes [and make additional modifications] or
select OK to exit the Date/Time settings.
2.5.2 Entering the Data
To select and open programs, select Start > Programs from the task bar to open a list
of available programs. Or if the program has a icon on the desktop, double-tap to open
it.
There are several ways to enter data on the PDT once in an application:
z Use the keypad to enter alpha-numeric characters, Refer to “2.4.7 Using the
2-19
SC800 keypad”.
z Use the stylus on the touch screen.
z Select text in the same way you select the text on a PC. Use the stylus to
highlight the desired text by dragging the stylus across the desired text,
double-tapping to select one word and triple-rapping to select an entire
line/paragraph. Refer to “2.5 Navigating the Display” starting.
z Use the soft input panel (digital keyboard) with the stylus.
z Use the bar code scanning to enter data. Press the trigger or “Barcode Scan” key
to initiate a scan. The scanned data will enter the current application’s open file.
Refer to “2.5.7 Reading barcodes, 1D laser version” starting for more
information on using a scanner.
For more information on factory installed applications, Refer to Chapter 4 “ Software
Programs”.
2.5.3 The Command Bar
Use the Command bar at top of the screen to perform tasks in programs, such a
opening a file, or editing a file.
2.5.4 The Task Bar
The Task bar at the bottom of the screen displays the icon, an icon for the active
program, the current time, and system icons for utilities loaded in memory. The Task
bar includes menu names, buttons, and the keyboard icon, which opens and closes the
soft input panel (SIP). The Task bar allows you to select and close programs. Refer to
Figure 2-19 to view the Task bar.
Figure 2-19 Task Bar & Command Bar
Command Bar
Task Bar
2-20
2.5.5 The Soft Keypad
In applications that accept keypad input, the soft input panel (SIP) can be used to
enter data using the stylus. The SIP is digital, QWERTY-style keyboard.
To open the SIP, tap the keyboard icon to open the menu and select Hide Input
Panel to close the keyboard.
Use the stylus to select letters, numbers, or symbols from the Soft Input Panel for the
current application.
2.5.6 Setting Up Wireless LAN
The Summit Client Utility (SCU) is an application designed for end users and administrators
of mobile devices that use a Summit radio module. Using SCU, an end user can:
z Disable the radio (turn it off) and enable the radio (turn it on)
z View the contents of configuration profiles, or profiles, each of which houses the RF,
security, and other settings for the radio
z Select the profile to be used to connect to a WLAN
z View global settings, which apply to every profile
z View status information on the radio, the access point (AP) or WLAN router to which it
is connected, and the RF connection or link between the two
z To troubleshoot a connection or performance issue, view in-depth diagnostic
information on the connection and the radio, and perform various troubleshooting and
diagnostic tests
After completing an administrator login to the utility, a user can perform these additional
tasks:
z Create, rename, edit, and delete profiles
z Alter global settings, which apply to every profile
SCU provides a graphical user interface (GUI) for access to all of its functions. Access to
these functions also is available through an application programming interface (API), which
an application programmer can use to enable another utility to manage the radio.
To initialize SCU:
z From the Start menu, select Programs
z Select the directory called Summit
z Inside the Summit directory are two items: a directory for the storage of security
certificates and an SCU icon. To run SCU, double-click the SCU icon
SCU has five tabs: Main, Profile, Status, and Diags, and Global.
Each tab is described in more detail in this section.
2-21
Main Tab
z Enable/Disable Radio: When the radio is enabled, selecting this button disables it;
when the radio is disabled, selecting this button enables it.
z Active Profile: You can view the name of the active profile and, using the selection list,
select a different profile.
If you select “ThirdPartyConfig” then, after the device goes through a power cycle,
WZC is used for configuration of the radio.
z Status: Indicates the radio’s status.
z Radio Type: Indicates the type of radio in the device.
“BG” means a Summit radio that supports 802.11b and 802.11g.
z Regulatory Domain: Indicates the regulatory domain or domains for which the radio is
configured.
“Worldwide” means that the radio can be used in any domain.
The domain cannot be configured by an administrator or user.
z Driver: Indicates the version of the device driver that is running on the device.
z SCU: Indicates the version of SCU that is running on the device.
z About SCU: When tapped, supplies information on SCU that on a Windows application
normally would appear under Help\About.
Profile Tab
Profile settings are radio and security settings that are stored in the registry as part of a
configuration profile. When a profile is selected as the active profile on the Main tab, the
settings for that profile become active. An administrator can define up to 20 profiles, edit
2-22
them, and delete them on the Profile tab in SCU. Profile changes made on the tab are
saved to the profile only when the Commit button is pressed.
Unless it is modified, the Default profile does not specify an SSID, EAP type, or method of
encryption. If the Default profile is the active profile, then the radio will associate only to an
access point that broadcasts its SSID and requires no EAP type and no encryption.
z Edit Profile: This is used to select the profile to be viewed or, if you are an
administrator, edited.
z Actions: Four actions are available, with the first three available only to an
administrator:
- New: Create a new profile with default settings and give it a unique name (and then
change settings using other selections on the tab). -Rename: Give the profile a new
name, one that is not assigned to another profile
- Delete: Delete the profile, provided that it is not the active profile.
- Scan: Open a window that lists access points that are broadcasting their SSIDs. Each
time you tap the Refresh button, you view an updated list of APs, with each row
showing an AP’s SSID, its received signal strength indication (RSSI), and whether
or not data encryption is in use (true or false). You can sort the list by clicking on
the column headers. If you are authorized as an administrator, select an SSID in
the list, and tap Commit, you return to the Profile tab to create a profile for that
SSID.
z Radio: Radio attributes in the list box can be selected individually. When an attribute is
selected, the current setting or an appropriate selection box with the current setting
highlighted appears on the right.
2-23
z Security: Values for the two primary security attributes, EAP type and encryption type,
are displayed in separate dropdown lists, with the current values highlighted. When
you as an administrator select an EAP type, the Credentials button appears; when you
tap it, a dialog box appears that enables you to define authentication credentials for that
EAP type. When you as an administrator select an encryption type that requires the
definition of WEP keys or a pre-shared key, the PSKs/WEP Keys button appears; when
you tap it, a dialog box appears that enables you to define WEP keys or a PSK.
z Commit: To ensure that changes to profile settings made on the tab are saved in the
profile, you must tap the Commit button.
To cause a Summit radio to connect to a typical business WLAN, you must select a profile
that specifies the SSID, EAP type, and encryption type supported by the WLAN:
z SSID: This is the name or identification of the WLAN.
z EAP type: This is the protocol used to authenticate the device and its user if the WLAN
uses the Enterprise version of Wi-Fi Protected Access (WPA) and WPA2. SCU
supports five EAP types: PEAP with EAP-MSCHAP (PEAP-MSCHAP), PEAP with
EAP-GTC (PEAP-GTC), EAP-TLS, LEAP, and EAP-FAST
z Encryption: This specifies the type of key used to encrypt and decrypt transmitted data
and how that key is specified or derived. Encryption options include:
- WPA2 or WPA with dynamic keys (derived from the EAP authentication process)
- WPA2 or WPA with pre-shared keys
- Static WEP keys
Consult the user’s guide for details on all profile settings, including security settings.
Status Tab
The Status tab provides status information on the radio.
z Active profile
z Radio’s status: Down (not recognized), Disabled, Not Associated, Associated, or [EAP
type] Authenticated
z Client info: Name, IP address, and MAC address
z AP info: Name, IP address, MAC address, beacon period, and DTIM interval
z Connection info: Channel, data rate, transmit power, signal strength, and signal quality
2-24
Diags Tab
z (Re)connect: Disable and enable the radio, apply or reapply the current profile, and
attempt to associate and authenticate to the wireless LAN, logging all activity in the
output area at the bottom.
z Release/Renew: Obtain a new IP address through DHCP release/renew, and log all
activity in the output area at the bottom.
z Start Ping: Start a continuous ping to the address in the edit box next to it. Once the
button is clicked, its name and function will change to Stop Ping. Moving to an SCU
window other than Status or Diags also will stop the ping, as will Pings will continue
2-25
until you tap the Stop Ping button, move to an SCU window other than Diags or Status,
exit SCU, or remove the radio.
z Diagnostics: Attempt to (re)connect to an AP, and provide a more thorough dump of
data than is obtained with (Re)connect. The dump will include radio state, profile
settings, global settings, and a BSSID list of APs in the area.
z Save To...: Save the diagnostics output to a file.
Global Tab
Global settings include:
z Radio and security settings that apply to all profiles
z Settings that apply to SCU itself
An administrator can define and change most global settings on the Global Settings Tab in
SCU.
The default setting for each global setting ensures reliable operation in most environments.
Consult the user’s guide for details on all global settings.
2.5.7 Reading barcodes, 1D laser version.
To use the scanning function, complete the following steps:
1. If you have not already done so, remove the protective plastic film before using
devices equipped with a 1D laser bar code reader.
2. Select Start > Setting > Control Panel > Barcode Setting; complete all
2-26
configurations following all description of 3.2.1 BarCode Setting.
3. Run the WordPad software program.
4. Press one of the three barcode reader trigger buttons.
5. Aim the scanning beam at the center of barcode.
6. Good scanning position.
The reading range is from 40 to 300mm distance.
1) Decrease the scanning distance to the bar code when scanning small
barcodes.
2) Increase the scanning distance from the bar code when scanning large
barcodes
3) The scanning area is visible by a red laser beam.
7. Bad scanning position.
1) Make sure that the laser beam sweeps across whole bar code.
2) Scanning operations may fail if the laser beam is positioned as below.
8. upon reading a barcode, the red LED indicator turns on until the trigger is
release or after five seconds. The green LED and the beep tone indicates a
good read.
Note: This product scans using laser light. Never look directly into the laser light or
shine the laser light into the eyes.
2.5.8 Help
To tap “?” can get help information for each program.
2-27
2.6 Power management
2.6.1 Suspend Mode
The PDT will go into a suspend mode when it
is idle for a period of time. The idle duration
can be customized using the Power control
panel (refer to Figure “Schemes Tab”)
Suspend mode works and looks just like you
have turned the unit off. Press the key to
suspend the PDT, Press the key again for
the PDT to resume its Previous state.
Use the Battery power control panel to set
the duration to switch state to Suspend mode
when system using battery power. This will
save battery power when PDT is not in use.
Figure 2-24 Schemes Tab
Suspending:
The following conditions will suspend:
z Press <Power> key while the unit is on.
z The duration timer of item “Switch state to Suspend” expires, which indicates
that there has been no use for a specified of time.
z The battery pack is completely discharged.
z Tap Start > Suspend
Tap here to let PDT enter into
suspend mode
2-28
2.6.2 Resuming
Use one of following methods to resume (wake up the PDT):
z Press <Power> key to suspend or resume (wake up).
z Put the PDT into a dock.
When a battery pack completely discharges while the unit is in suspend mode, the
PDT remains suspended until discharged battery condition is corrected.
2.7 Resetting the PDT
2.7.1 Software (Warm) Reset
A warm reset is a transition from the on, idle, or suspend power state that close all
applications, clears the working RAM, but preserves the file system.
Reason to Warm Reset: If an application “hangs”, initiate a warm reset to terminate
the application only.
Process to Warm Reset: To a warm reset, press “F1” and “F4” button
simultaneously.
After Warm Reset:
z The desktop appears with the application shortcuts on the screen.
z The custom settings in the registry are persistent.
2.7.2 Cold Reset
1) You can use Cold Reset to initiate device if WINCE.NET OS lock up or Warm
Reset still can’t work
2) To perform Cold Reset, press “Power”, “F1” and “F4” button simultaneously.
3) Device will initiate boot up after Cold Reset.
CAUTION: Only use the Warm Reset. Try warm reset before you initiate Cold
Reset. All applications will be Closed and working RAM and all files will be
cleared if you initiate the Cold Reset. It’s better usually to back up your files to
Flash ROM, Flash Card or PC.
3-1
Chapter 3. Setting
3.1 Introduction
To view available options for PDT’s setting, tap Start > Settings. Then, there are
three items inside Settings: “Control Panel”, “Network and Dial-up” and “Taskbar
and Start”.
3.2 Control Panel
To view the Control Panel and settings you can modify by tapping Start > Settings >
Control Panel.
Figure 3-1 Control Panel
3-2
3.2.1 BarCode Setting
CAUTION：Please do not enter into any Barcode Application Program before
settings completing this Barcode.
There are three Tabs for scanner configuration setting: “Basic” Tab,
“Code Configure” Tab and “Code ID” Tab. In addition, there is
“BarCode Setup” for the “Code Configure” Tab.
3.2.1.1 “Basic” Tab
Figure 3-2 Basic Tab
Table 3-1 Basic Explaining
Field Name Function Explaining
Select the numbers of beep tone after scan OK.
None After scanning the barcode, do not give out
beep sound.
Beep After Scan
OK
One Time After scanning the barcode, give out beep
one time.
3-3
Field Name Function Explaining
Two Times After scanning the barcode, give out beep
two times.
Scan Timeout
(sec)
Select the scanning timeout duration (in seconds) from this
pull-down list. <2 ~ 20 sec, Default: 5>
None After showing barcode, do not action.
CRLF After showing the barcode, jump to next
row.
Space After showing the barcode, jump one unit.
Termination
Code
Tab After showing the barcode, jump a section.
Disable Disable this functionality.
Continuous
Scan 1 ~5 sec Alternate second number of Continuous
Scan.
Select a method based upon the barcode scanning application
you will use.
Type Writing A unit continues a unit, fast showing
barcode number.
Copy & Paste Once show barcode number.
Keybd Message
Disable Not show the barcode number.
Prefix Type the desired label prefix in this text box
Suffix Type the desired label suffix in this text box
Default Press “Default” button to reset all configuration setting of
“Basic” Tab into default values.
F/W ver. Decoder firmware version.
Set All To
Default
Press “Set All To Default” button to reset all configuration
setting of “Basic” Tab, “Code Configure” Tab, “Code ID” Tab
and all barcode of “BarCode Setup” into default values.
3-4
3.2.1.2 “Code Configure” Tab:
Select the barcode symbologies you plan to scan from the list. Tap to enable/disable
the desired symbologies.
Figure 3-3 Code Configure Tab
Table 3-2 Code Configure Explaining
Barcode Symbology Explaining
Type A. Numeric-only Barcodes
UPC-E Compressed version of UPC code for use on small
products.
UPC-A Universal product code seen on almost all retail
products in the USA and Canada.
EAN-13 / ISBN EAN-13: European Article Numbering
international retail product code.
ISBN: Special use of the EAN-13 symbol to used
internationally to mark books.
EAN-8 / JAN-8 Compressed version of EAN code for use on
small products.
UPC-EAN Add-ON 2/5 UPC-A, UPC-E, EAN-13, and EAN-8 may all
include an additional barcode to the right of the
main barcode. This second barcode, which is
usually not as tall as the primary barcode, is used
to encode additional information for newspapers,
3-5
books, and other periodicals.
Industrial 2 of 5 / IATA Older code not in common use.
Interleaved 2 of 5 Compact numeric code, widely used in industry,
air cargo, other applications.
Plessey / MSI Plessey: Older code commonly used for retail
shelf marking.
MSI: Variation of the Plessey code commonly
used in USA.
Code 11 Used primarily for labeling telecommunications
equipment.
Codabar / NW 7 Older code often used in library systems,
sometimes in blood bank.
Matrix 2 of 5 Used in miscellaneous industrial applications, and
mechanical numbering systems.
Type B. Alphanumeric Barcodes
Code 39 / Code32 General-purpose code in very wide use
world-wide.
Code 93 Compact code similar to Code 39.
Code128 / UCC EAN128 Very capable code, excellent density, high
reliability; in very wide use world-wide.
Widely used data formatting model for Code 128
Type C. Others Barcodes
China Post Used by China Postal Service for automated mail
sorting.
Code 4 ---
GTIN Global Trade Identification Number
Korea Code 3 of 5 ---
RSS Reduced Space Symbology
3-6
3.2.1.3 “Code ID” Tab:
Figure 3-4 Code ID Tab
Table 3-3 Code ID Explaining
Code ID is added into prefix of the barcode and let user identify which kind of
barcode being scanned.
Enable Code ID Enable this functionality.
Set 1 ~ Set 5 Select one default value by Set 1 ~ Set 5.
(See the “Table 3-4 Code ID Set1-Set5 Table”)
User Define Establish number by oneself.
Barcode List Set 1 ~ Set 5: defaults setting.
User Define: select barcode to define.
Default Press “Default” button to reset all configuration
setting of “Code ID” Tab into default values.
Table 3-4 Code ID Set1-Set5 Table
Set 1 Set 2 Set 3 Set 4 Set 5
UPC-E S E C E E
UPC-A M A A A E
EAN-13 / ISBN M A A F E
EAN-8 / JAN-8 P B B F E
Industrial 2 of 5 / IATA C H H H S
Interleaved 2 of 5 D I Z I S
3-7
Set 1 Set 2 Set 3 Set 4 Set 5
Plessey / MSI V V D P M
Code 11 J J J J J
Codabar / NW 7 F N X N F
Matrix 2 of 5 E G G G S
Code 39 / Code 32 A C Y M A
Code 93 I L L L G
Code 128 H K K K C
Code 4 U U U U U
Korea Code 3 of 5 R R R R R
RSS R R R R R
UCC128 / EAN128 W W W W W
3.2.1.4 BarCode Setup
A. First select barcode type then select barcode to setting.
B. Press “Default” button to reset all configuration setting of this barcode into default
values.
C. Press “Apply” button to be decided setting of this barcode.
Please see 3.2.2 Symbologies List for more detail information of each Barcode.
Figure 3-5 BarCode Setup
3-8
3.2.2 Symbologies List
A Type -- Numeric-only Barcodes
3.2.2.1 UPC-E
Figure 3-6 UPC-E
Table 3-5 UPC-E Explaining
Item Explaining
Ignore 1st digit Do not transmit 1st digit by barcode.
Format Transmit 1st digit Transmit 1st digit by barcode.
Send Check Digit Whether send check digit by barcode.
3-9
3.2.2.2 UPC-A
UPC-A movements together with EAN-13, so only Enable EAN-13 then UPC-A will
be Enable, too.
Figure 3-7 UPC-A
Table 3-6 UPC-A Explaining
Item Explaining
Ignore 1st & 2nd digits Do not transmit 1st digit by barcode.
Transmit 1st digit Transmit 1st digit by barcode.
Transmit 2nd digit Transmit 2nd digit by barcode.
Format
Transmit 1st & 2nd
digits Transmit 1st & 2nd digits by barcode.
Send Check Digit Whether send check digit by barcode.
3-10
3.2.2.3 EAN-13 / ISBN
Figure 3-8 EAN-13 / ISBN
Table 3-7 EAN-13 / ISBN Explaining
Item Explaining
Ignore 1st & 2nd digits Do not transmit 1st digit by barcode.
Transmit 1st digit Transmit 1st digit by barcode.
Transmit 2nd digit Transmit 2nd digit by barcode.
Format
Transmit 1st & 2nd
digits Transmit 1st & 2nd digits by barcode.
Send Check Digit Whether send check digit by barcode.
Enable ISBN Code Whether use this ISBN Code.
3-11
3.2.2.4 EAN-8/JAN-8
Figure 3-9 EAN-8/JAN-8
Table 3-8 EAN-8/JAN-8 Explaining
Item Explaining
Ignore 1st digit Do not transmit 1st digit by barcode.
Format Transmit 1st digit Transmit 1st digit by barcode.
Send Check Digit Whether send check digit by barcode.
Convert to EAN-13 When this option is selected the scanner
will convert EAN-8 to EAN-13 by
transmitting five zeroes …
Ahead of code Add five zeroes at prefix of the barcode.
Add five 0
After 3 digits Add five zeroes after 3rd digits.
3-12
3.2.2.5 UPC-EAN Add on 2/5
A. UPC-E, UPC-A, EAN-13 / ISBN and EAN-8 / JAN-8 may all include an
additional barcode to the right of the main barcode.
B. This barcode will show primary & additional code together.
C. So the UPC-EAN Add-ON 2/5 code is unable to use alone, must operate in
UPC-E or UPC-A or EAN-13 / ISBN or EAN-8 / JAN-8.
Figure 3-10 UPC-EAN Add on 2/5
Table 3-9 UPC-EAN Add-On 2/5 Explaining
Item Explaining
Only read the code with Addon 2/5 Only reads the codes that have addenda.
3-13
3.2.2.6 Industrial 2 of 5 / IATA
Figure 3-11 Industrial 2 of 5 / IATA
Table 3-10 Industrial 2 of 5 / IATA Explaining
Item Explaining
Send Check Digit Whether send check digit by barcode.
Enable IATA Code Whether use this IATA Code.
Checksum Verify Whether verify checksum by barcode.
Min Length can be set from 2 to 48
Min-Max
(Default: 2 / 48) Max Length can be set from 2 to 48
Length 1 can be set from 2 to 48
Length 2 can be set from 2 to 48
Length
Fixed
Length 3 can be set from 2 to 48
3-14
3.2.2.7 Interleaved 2 of 5
Figure 3-12 Interleaved 2 of 5
Table 3-11 Interleaved 2 of 5 Explaining
Item Explaining
Send Check Digit Whether send check digit by barcode.
Checksum Verify Whether verify checksum by barcode.
Min Length can be set from 4 to 48
Min / Max
(Default: 4 / 48) Max Length can be set from 4 to 48
Length 1 can be set from 4 to 48
Length 2 can be set from 4 to 48
Length
Fixed
Length 3 can be set from 4 to 48
3-15
3.2.2.8 Plessey / MSI
Figure 3-13 Plessey / MSI
Table 3-12 Plessey / MSI Explaining
Item Explaining
Mode 10
Mode 10-10
Format
Mode 11-10
Checksum mode for this barcode.
Send Check Digit Whether send check digit by barcode.
1 Digit Check 1 digit & send by checksum.
2 Digits Check 2 digits & send by checksum.
3-16
3.2.2.9 Code11
Figure 3-14 Code 11
Table 3-13 Code 11 Explaining
Item Explaining
Send Check Digit Whether send check digit by barcode.
1 Digit Check 1 digit & send by checksum.
2 Digits Check 2 digits & send by checksum.
3-17
3.2.2.10 Codabar / NW7
Figure 3-15 Codabar / NW7
Table 3-14 Codabar / NW7 Explaining
Item Explaining
Start / Stop Digit Whether transmit Start & Stop Digit.
ABCD
abcd
TN*E
tn*e
Start / Stop transmit type
Checksum Verify Whether verify checksum by barcode.
3-18
3.2.2.11 Matrix 2 of 5
Figure 3-16 Matrix 2 of 5
Table 3-15 Matrix 2 of 5 Explaining
Item Explaining
Send Check Digit Whether send check digit by barcode.
Checksum Verify Whether verify checksum by barcode.
Min Length can be set from 4 to 48
Min-Max
(Default: 4 / 48) Max Length can be set from 4 to 48
Length 1 can be set from 4 to 48
Length 2 can be set from 4 to 48
Length
Fixed
Length 3 can be set from 4 to 48
3-19
B Type -- Alphanumeric Barcodes
3.2.2.12 Code39 / Code32
Figure 3-17 Code39 / Code32
Table 3-16 Code39 / Code32 Explaining
Item Explaining
Code39 Standard Enable Code 39 Standard characters
Code39 Full ASCII Enable Code 39 Full ASCII character
Format
Code32 Enable Code 32
Start / Stop Digit Whether transmit Start & Stop Digit.
Verify Whether verify checksum by barcode.
Checksum Transmit Whether transmit checksum by barcode.
3-20
3.2.2.13 Code93
The barcode do not have setting.
Figure 3-18 Code93
3.2.2.14 Code128 / UCC EAN128
Figure 3-19 Code 128 / UCC EAN128
Table 3-17 Code128 / UCC EAN128 Explaining
Item Explaining
Enable UCC128/EAN128 Enable UCC128/EAN128.
3-21
C Type -- Others Barcodes
3.2.2.15 China Post
Figure 3-20 China Post
Table 3-18 China Post Explaining
Item Explaining
Checksum Verify Whether verify checksum by barcode.
Send Check Digit Whether send check digit by barcode.
Min Length can be set from 4 to 48
Min-Max
(Default: 4 / 48) Max Length can be set from 4 to 48
Length 1 can be set from 4 to 48
Length 2 can be set from 4 to 48
Length
Fixed
Length 3 can be set from 4 to 48
3-22
3.2.2.16 Code4
The barcode do not have setting.
Figure 3-21 Code4
3.2.2.17 GTIN
The barcode do not have setting.
Figure 3-22 GTIN
3-23
3.2.2.18 Korea Code 3 of 5
The barcode do not have setting.
Figure 3-23 Korea Code 3 of 5
3.2.2.19 RSS
Figure 3-24 RSS
Table 3-19 RSS Explaining
Item Explaining
Convert to UCC128 The scanner will convert RSS to UCC128.
Checksum Veri fy Whether verify checksum by barcode.
3-24
3.2.3 Bluetooth Device Properties
Table 3-20 Bluetooth Device Properties
ICON ITEM & FUNCTION
z “BT Service” Tab ( Figure 3-25) :
9 Tap the “Enable Bluetooth Device” to enable Bluetooth device.
9 Wait for 20 seconds in order to initialize the Bluetooth hardware
correctly.
9 Click “Scan Device Service” to pop “Bluetooth Manager”
window. Then tap the Scan Device button to initiate a scan for
Bluetooth hardware. The Bluetooth manager lists the Bluetooth
devices that it finds, see Figure 3-26. If Bluetooth hardware is
not found the Bluetooth Hardware Error window appears, see
Figure 3-27. Table 3-21 described the Bluetooth Icons.
9 Double tap the device to connect to on the device list. The
Bluetooth Manager Authentication window appears. Tap No to
connect to the device without authentication, or tap Yes to
authenticate the device before connecting. (Figure 3-28)
9 If the Yes button was selected in the Bluetooth Manager
Authentication window, the enter PIN windows appears. Enter a
PIN (between 1 and 16 characters) in the Enter PIN: text box,
and tap OK. The mobile computer sends the PIN request to the
device for bonding. (Figure 3-29)
9 When prompted, the same PIN must be entered on the other
device. When the PIN is entered correctly on the other device,
the bonded icon appears on the device list. (Figure 3-30)
z “Serial Port” Tab ( Figure 3-30-1) :
9 Tap the “Enable Bluetooth Device” to enable Bluetooth device.
9 Wait for 20 seconds in order to initialize the Bluetooth hardware
correctly.
9 If want to use Virtual com, only SPP base profiles are
supported.(i.e. Printer, Modem, and LAP).Switch to “Serial
Port” tab, and will see the devices you had trusted or active.
Select the device that you want to map a virtual com and which
virtual com you want to use.
9 Now COM1 has mapped for BT device.
3-25
Figure 3-25 Bluetooth Device Properties Figure 3-25-1 Bluetooth Device Properties
Figure 3-26 Bluetooth Manager Windows Figure 3-26-1 Bluetooth Manager Windows
Figure 3-27 Bluetooth Error Windows Figure 3-28 Bluetooth Manager Windows
3-26
Figure 3-29 Bluetooth Enter PIN Windows Figure 3-30 Bluetooth Manager Windows
Figure 3-30-1 Bluetooth Manager Windows Figure 3-30-2 Bluetooth Manager Windows
3-27
Figure 3-30-3 Bluetooth Manager Windows Figure 3-30-4 Bluetooth Manager Windows
Note: If the device to which the mobile computer is bonding does not appear in the list,
ensure it is turned on, in discoverable mode, and within range (30 feet / 10 meters) of the
mobile computer.
Table 3-21 Bluetooth Icon
Icon Description
Unknown device icon Device is not defined
Locked icon Device is locked and cannot be bonded to.
Not locked icon Device is not locked and can be bonded to.
Bluetooth device icon Bluetooth device
Bonded device icon Bonded Bluetooth device
Mobile device icon Device is a mobile device
Phone icon Device is a phone.
Printer icon Device is a printer
Network icon Device is a network.
3-28
Icon Description
Linked icon Device is linked.
3.2.4 Certificates
Certificates are used by some applications for establishing trust and for secure
communications.
Certificates are signed and issued by certificate authorities and are valid for a
prescribed period of time. Windows CE manages multiple certificate stores.
Table 3-22 Certificates
ICON ITEM & FUNCTION
z “Store” Tab ( Figure 3-31) :
9 In the Stores tab, select the certificate store you wish to view or
modify from the drop-down list (Figure 3-32).
9 The “Trusted Authorities “store lists the top-level certificates
for authorities you trust.( Figure 3-33 , Figure 3-34)
9 The “My Certificates “store contains your personal certificates,
which you use to identify yourself.
9 Intermediate certificate authorities that help establish a chain of
trust are stored in the “Other Authorities” store.
z “Store” Tab :
9 To add a certificate or associated private key to the selected
store, select “Import” (Figure 3-35).
9 To view more details of the selected certificate, such as the
expanded name or expiration date, choose “View”.
9 To delete the selected certificate from the store, choose
“Remove”.
3-29
Figure 3-31 Certificates Figure 3-32 Certificates
Figure 3-33 Certificates Figure 3-34 Certificates
Figure 3-35 Certificates
3-30
3.2.5 Control Center
The Control Center includes four AP, listed the following ......
Figure 3-36 Control Center
3.2.5.1 Information
Table 3-23 Information
ICON ITEM & FUNCTION
z “Information” Tab :
9 Provide Software version, MAC address, Bluetooth ID, Serial
No. and Configuration No.
3-31
3.2.5.2 Brightness
Table 3-24 Brightness
ICON ITEM & FUNCTION
LCD Brightness
Set the LCD brightness by adjusting the slider from low to high
Amounts 5 steps: Every step have corresponding picture of self.
1. 2. 3. 4. 5.
The table must disable when its item is not
marked.
Battery Power, turn
off backlight after
The table has 15 seconds, 30 seconds, 1
minute, 2 minutes and 5 minutes.
The table must disable when its item is not
marked.
AC Power, turn off
backlight after
The table has 15 seconds, 30 seconds, 1
minute, 2 minutes and 5 minutes.
Enable Keypad
Brightness
Open keypad brightness or not.
Figure 3-37 Brightness
3-32
3.2.5.4 Fn-key Settings
Table 3-26 Fn-Key
ICON ITEM & FUNCTION
z Fn-Key Setting (Figure 3-42)
Fn Key The Application Program of default setting
F1 Internet Explorer
F2 Microsoft WordPad
F3 Inbox
F4 My Computer
F5 Barcode Settings
F6 Media Player
F7 <None>
F8 Information
Only for SC820
9 To assign your favorite application program to Hot Keys.
9 Choose one of Hot Keys from pull-down list.(Figure 3-43)
9 To tap “Browse…” inside “Assign program” applet.
9 Select one application program you want from program list, then,
choose “OK”. (Figure 3-43)
9 To tap “Default” to return back to default setting. (Figure 3-42)
Figure 3-42 Fn-Key Settings Figure 3-43 Fn-Key Settings
3-33
3.2.5.3 Backup Restore
Table 3-25 Backup Restore
ICON ITEM & FUNCTION
1. You can backup/restore system to/from flash disk or inserted
memory card. (A. Disk on Chip, B. CF Card, C. SD Card)
( Figure 3-38)
2. When you launch this AP, it must check backup file in DOC
first. And if you select other storage, it will check again.
3. Then if it has the file, appeared its date behind “Last backup
date:”; if not, disable “Restore Now” Button.
4. When you press the Backup/Restore Button will be a warning
dialog pop up. ( Figure 3-39)
5. When system backup/restoring finished will be a message
dialog will pop up. (A. Backup: Figure 3-40, B. Restore: Figure
3-41)
Figure 3-38 Backup Restore Figure 3-39 Backup & Restore Start
Figure 3-40 Backup OK Figure 3-41 Restore OK
3-34
3.2.6 Date/Time
Table 3-27 Date/Time
ICON ITEM & FUNCTION
z “Date/Time” Tab :( Figure 2-14)
9 Please see the detail information of 2.5.1 Setting Time and
Date on P.2-21
3.2.7 Dialing Properties
Table 3-28 Dialing properties
ICON ITEM & FUNCTION
z “Dialing Properties” Tab :( Figure 3-44)
9 In the When dialing from list, select the “Location” where you
want to change settings.(Figure 3-45)
9 To create a new location, select “New”. Enter the name of the
location, and then select “OK”.(Figure 3-46)
9 Enter or edit the area code and local country code as needed.
9 In Dial using, select “Tone dialing” or “Pulse dialing”. Most
phone lines are tone.
9 To automatically disable call waiting, select “□ Disable call
waiting by dialing”, select the appropriate number sequence in
the list, or enter a new sequence.
z Editing dialing patterns (Figure 3-47)
9 Using the codes listed in the topic; revise the dialing patterns as
needed.
Notes:
If you need to use character other than the ones listed here,
use manual dialing.
Hyphens and spaces in dialing strings are ignored.
Some modems may not respond to the following characters,
even though your device lets you add them to the dial
string.
3-35
Figure 3-44 Dialing Properties Figure 3-45 Dialing Properties
Figure 3-46 Dialing Properties Figure 3-47 Dialing Properties
3-36
3.2.8 Display Properties
Table 3-29 Display properties
ICON ITEM & FUNCTION
z “Background” Tab :( Figure 3-48)
9 From the “Image” list, select an image you want as the
background of the desktop.(Figure 3-49)
9 To locate an image in another folder, select “Browse”.(Figure
3-50)
9 To have the image cover the entire background, select “ □Tile
image on background”
z “Appearance” Tab(Figure 3-51)
9 Change the color scheme :( Figure 3-52)
¾ From the” Scheme” list, select a scheme.
¾ View your choice in the preview box. If you like the scheme,
select “Apply”.
9 Create a custom color scheme:
¾ From the “Item” list, select a display item.
¾ From the “Basic colors” list, select a color, and select “OK”.
¾ View your color selection(s) in the Preview box.
¾ To save the scheme, select “Save”.
¾ In the “Save this color scheme as” box, enter a name for the
scheme, and select “OK”.
¾ Select “Apply”.
Figure 3-48 Display properties Figure 3-49 Display properties
3-37
Figure 3-50 Display properties Figure 3-51 Display properties
Figure 3-52 Display properties
3.2.9 Input Panel
Table 3-30 Display properties
ICON ITEM & FUNCTION
z “Input panel” Tab :( Figure 3-53)
9 Select the input method you want to change.
9 To change the Soft Keyboard Options , tap “Option” (Figure
3-54) .
3-38
z “Options” Tab :
9 Change the soft keyboard options as desired, selecting from:
¾ Large or small keys
¾ Using gestures for space, black-space shift, and enter.
9 To exit the soft keyboard Options, press “OK” on the control
bar, or press the <Enter> key on the keypad.
9 To exit the Input Panel, press “OK” on the control bar, or press
the <Enter> key on the keypad.
.
Figure 3-53 Input Panel Properties Figure 3-54 Input Panel Properties
3.2.10 Internet Options
Table 3-31 Internet Options
ICON ITEM & FUNCTION
z “General” Tab :( Figure 3-55)
9 Type in the URL of desired start page and the desired search
engine. You also change the Cache Size, clear the Cache and
Clear the History..
z “Connection” Tab :( Figure 3-56)
9 Modify the network access setting as desired.
3-39
z “Security” Tab (Figure 3-57)
9 Modify the security settings as desired. You can enable any of
the following by tapping the checkbox:
¾ Allow cookies
¾ Allow TLS 1.0 security
¾ Allow SSL 2.0 security
¾ Allow SSL 3.0 security
¾ Warm when switching across secure and insecure areas.
z “Advanced” Tab (Figure 3-58)
9 Modify the security settings as desired. You can enable any of
the following by tapping the checkbox:
¾ Display Image in pages
¾ Play sounds in pages
¾ Enable scripting
¾ Display a notification about every script error
¾ Underline links-
○ Never
○ Always
○ Hover
Figure 3-55 Internet Settings Figure 3-56 Internet Settings
3-40
Figure 3-57 Internet Settings Figure 3-58 Internet Settings
3.2.11 Keyboard
Table 3-32 Keyboard
ICON ITEM & FUNCTION
z “Repeat” Tab :( Figure 3-59)
9 To change the amount of time between depressions before
repetition starts, adjust the Repeat delay slider
9 To change the repeat rate, adjust the Repeat rate slider.
9 Test your new setting.
9 Tap “ OK” to exit the “Keyboard” Tab.
3-41
Figure 3-59 Keyboard Properties
3.2.12 Network and Dial-up Connections
Table 3-33 Network and Dial-up Connections
ICON ITEM & FUNCTION
z “Connection” Tab :
9 To create a “Dial-up Connection”:
¾ Double-tap the “Make New connection”.
¾ In the “Make New Connection” dialog box, enter a name for
the connection.
¾ Select “Dial-Up Connection”.
¾ Select the “Next” button.
¾ Select the modem you want use.
¾ Select “Configure”
¾ Under “Connection Reference”, use the default settings
provided. If you can’t connect using these settings, see your
ISP or network administrator for specific information. If you
want to always enter a phone number before connecting,
Select “Manual Dial”. Select “OK”.
3-42
¾ Select “TCP/IP Settings”. In the “General” tab, ensure “Use
Server-assigned IP address” is selected. In the “Name
Servers” tab, ensure “Use Server-assigned addresses” is
selected, and select “OK”. If you are unable to connect with
these default settings, see your ISP or network administrator
for specific TCP/IP information.
¾ Select the “Next” button and type the telephone number.
¾ Select the “Finish” button.
The connection you just created appears as an icon in the “Network
and Dial-up Connections” folder.
9 Set up a point-to-Point Protocol(PPP) account with an ISP and
obtain the following information:
¾ Access telephone number
¾ User name
¾ Password
Once you have established an account, create a new connection on
your device. When creating this connection, you should be able to use
all of the default TCP/IP settings provided in the Make New
Connection Wizard. If you can’t connect using the default settings,
contact your ISP or access your ISP’s Web site for specific TCP/IP
information as well as primary and secondary DNS address.
9 Modify connection setting
¾ Select Start > Settings > Network and Dialup Connections
¾ Select the icon for connection settings you want to modify.
¾ Select File > Properties, or double- tap the appropriate icon.
¾ Select desired options. There may be additional settings that
depend on the connection. To modify, select the icon and
select the icon and select Advanced Settings… from the
menu.
3-43
Figure 3-60 Network and Dial-up Connections Figure 3-61 Network and Dial-up Connections
Figure 3-62 Network and Dial-up Connections Figure 3-63 Network and Dial-up Connections
3-44
Figure 3-64 Network and Dial-up Connections Figure 3-65 Network and Dial-up Connections
Figure 3-66 Network and Dial-up Connections Figure 3-67 Network and Dial-up Connections
3-45
Figure 3-68 Network and Dial-up Connections Figure 3-69 Network and Dial-up Connections
Figure 3-70 Network and Dial-up Connections Figure 3-71 Network and Dial-up Connections
3.2.13 Owner
Table 3-35 Owner
ICON ITEM & FUNCTION
z “Identification” Tab : (Figure 3-72)
3-46
9 Fill in or edit the data as desired.
9 To have this information displayed when you start your device,
select “Display Owner Identification” at Power On.
9 To set up identification for remote networks, see Setting up
identification for remote networks.
z “Network ID” Tab: (Figure 3-73)
9 Enter the user name, password, and domain name you use to log
on to remote network.
Figure 3-72 Owner Properties Figure 3-73 Owner Properties
3.2.14 Password
Table 3-36 Password
ICON ITEM & FUNCTION
z “Password Setting” Tab : (Figure 3-74)
9 Enter the password
9 In the “Confirm password “box, enter the password again.
9 To require the password on startup, select “Enable password
protection at power- on“. and/or select “Enable password
protection for screen saver”
9 To exit the Password control panel, press “OK” from the
control bar, or press the <Enter> key on the keypad.
3-47
Figure 3-74 Password Properties
3.2.15 PC Connection
Table 3-37 PC Connection
ICON ITEM & FUNCTION
z “PC Connection” Tab : (Figure 3-75)
9 Select the first checkbox to enable direct connections to the
desktop computer. (Figure 3-75)
9 Tap the “Change Connection…” button to modify the
connection method from USB or Serial. (Figure 3-76)
9 To exit the “Change Connection” dialog, press “OK” from the
control bar, or press the <Enter> key on the keypad.
9 To exit the “PC Connection” properties control panel, press
“OK” from the control bar, or press the <Enter> key on the
keypad.
3-48
Figure 3-75 PC Connection Figure 3-76 PC Connection
3.2.16 Power
Table 3-38 Power
ICON ITEM & FUNCTION
z “Battery” Tab : (Figure 3-77)
9 Provide change level indicators for Main battery and Backup
battery.
9 Provide remaining power capacity of main battery.
9 If a “Main Batteries very Low” warning message shows, the
remaining battery life is around 30 minutes to SC800 shuts
down. ( Figure 3-81)
9 The PDT will shutdown during the main batteries capacity is
around 0%
9 To exit Battery control panel, press “OK” from the command
bar, or press <Enter> key on keypad.
z “ Schemes” Tab: (Figure 3-78)
3-49
9 The Scheme Tab allows you to determine the time to switch
state to Suspend mode when using either Battery Power or AC
Power.
9 Select Battery Power or AC Power as the power scheme from
the pull-down list.( Figure 3-78)
9 Select the time to suspend mode from the pull-down list.
( Figure 3-79)
z “Device Status” Tab: ( Figure 3-80)
Provide power level of device – The power level ranges from
“ High(D0)” which means the device is at the highest power level to
“Off(D4)” which means the device is at the lowest power level.
Note:
This ICON inside the Task Bar shows that AC adapter provides power
to the PDT
The ICON inside the Task Bar shows that Main Batteries provides the
power to the PDT.
The ICON inside the Task Bar shows that AC adapter provides the
power to the PDT and is charging the main batteries..
Figure 3-77 Power Figure 3-78 Power
3-50
Figure 3-79 Power Figure 3-80 Power
Figure 3-81 Power
3.2.17 Regional Settings
Table 3-39 Regional Settings
ICON ITEM & FUNCTION
z “Region” Tab : (Figure 3-82)
9 Select the desired location/language.
9 Review the Appearance samples in the bottom half of the
screen.
9 Select the Tab at the top for any settings you wish to change,
Options to modify include Number, Currency, Time, and Date.
3-51
Figure 3-82 Regional Settings
3.2.18 Remove Programs
Table 3-40 Remove Programs
ICON ITEM & FUNCTION
z “Remove Programs” Tab :
9 Only user installed programs can be removed.
¾ Select the program you wish to remove from the list and press
“remove” button.
3-52
3.2.19 Storage Manager
Table 3-41 Storage Manager
ICON ITEM & FUNCTION
z “Storage Manager” Tab : (Figure 3-83)
9 To change Storage properties control panel default settings:
Insert. Compact Flash(CF) or Secure digital (SD) storage card into
the unit.
¾ Select Start > Settings > Control Panel > Storage Properties
¾ From the “Storage Info” pull-down list, select the desired
storage device.
¾ You can also format, dismount, and create partitions on storage
devices using this control panel.
¾ To save and exit the Storage Properties control panel, press
“OK” from the control bar, or press the <Enter> key on the
keypad.
Caution: Dismounting or formatting the DiskOnChip will
erase all files and program stored in Flash Memory
Figure 3-83 Storage Manager
3-53
3.2.20 Stylus
Table 3-42 Stylus
ICON ITEM & FUNCTION
z “Double-Tap” Tab : (Figure 3-84,Figure 3-85)
9 Double-tap the checkerboard grip at a comfortable speed.
9 Double-tap clapboard to test your settings
9 The function is OK if the figures are changed from Figure 3-84
to Figure 3-85.
9 To tap “OK” to exit the Stylus Properties.
z “Calibration”: (Figure 3-86, Figure 3-87)
9 In the Welcome Wizard, you tapped a target with the stylus to set
the amount of pressure needed for the screen to respond to your
stylus taps.
9 Please also see 2.4.3 Calibration of the touch Screen
Figure 3-84 Stylus Properties Figure 3-85 Stylus Properties
3-54
Figure 3-86 Stylus Properties Figure 3-87 Stylus Properties
3.2.21 System
Table 3-43 System
ICON ITEM & FUNCTION
z “General” Tab : (Figure 3-88)
9 To show:
¾ Firmware information
¾ Information about Processor type, Memory size, Expansion
card
z “Memory”: (Figure 3-89)
9 Move the slider to adjust memory allocation. Default storage
memory is normally is normally set to about 8MB with the
reminder assigned to Program memory.
9 Press the “OK” key on the Keypad.
Note: the difference is occupied by OS between the RAM size in
Information properties and total memory size of storage memory
and program memory
z “Device Name” Tab : (Figure 3-90)
9 Your device uses this information to identify itself to other
computers.
9 The input panel will open to facilitate data entry.
3-55
9 To close the Device Name, press the “OK” button, or press the
<Enter> key on keypad.
z “Copyrights” Tab: (Figure3-91)
9 Refer to this tab for specific copyright data. As a user, you are
responsible to read this statement.
Figure 3-88 System Properties Figure 3-89 System Properties
Figure 3-90 System Properties Figure 3-91 System Properties
3-56
3.2.22 Volume & Sounds Properties
Table 3-44 Volume & Sound
ICON ITEM & FUNCTION
z “Volume” Tab : (Figure 3-92)
9 The factory default for Volume is the forth level. You can adjust
the volume to your environment and comfort.
¾ Set the volume by adjusting the slider from Soft to Loud,
or press Right or Left edge of Navigation keys
z “Sounds ” Tab: (Figure3-93)
9 Enable the desired sounds for key clicks, screen taps,
notifications, and applications.
Figure 3-92 Volume & Sound Figure 3-93 Volume & Sound
3-57
3.3 Taskbar and Start Menu
Table 3-45 Taskbar and Start menu
ICON ITEM & FUNCTION
z “General” Tab :
9 In this tab, You can change the position of the Taskbar and Start
menu
¾ Is always on top or not
¾ Auto hide or not
¾ Show Clock or not
z “Advanced ” Tab:
Taskbar and
Start Menu
9 Tap the “Clear” button to remove the contents of the Documents
Menu.
9 Enable “□ Expand Control Panel” to list all icons of
Control Panel from top to bottom.
4-1
Chapter 4. Communication
4.1 Installing & Setting Up Microsoft ActiveSync
4.1.1 Installing Microsoft ActiveSync on the Host PC
Microsoft ActiveSync is a file transfer tool to synchronize the files on a PC with the
files on your PDT.
To install Microsoft ActiveSync, complete the following steps on the PC:
1. Go to the Microsoft Windows CE.NET website and download the latest current
version of ActiveSync:
http://www.microsoft.com/mobile/pockeypc/downloads/ .
2. Install the latest version of Microsoft ActiveSync on the host PC.
3. Open ActiveSync.
4. Select File > Communication Settings from AtiveSync’s menu bar.
5. Go to “Using ActiveSync” on page 4-1 to continue using ActiveSync.
4.1.2 Connecting PDT to Host PC
1. You can use either the USB/Serial (RS232) port of Single Dock or a USB/Serial
(RS232) cable to connect the PDT to the Host PC.
z To use the dock, you must first insert the PDT into the slot, making sure that the
unit is firmly seated the dock.
z To use the cable, connect the USB/Serial cable to the PDT.
2. Connect the USB/Serial dock or cable to the Host PC’s serial port or USB port.
3. Connect the dock or PDT to the power adapter and power source.
4.2 Using ActiveSync
Use ActiveSync to transfer and synchronize files between the PDT and the Host PC.
4.2.1 Setting up a Partnership
During the Microsoft ActiveSync installation, you were prompted to create a
partnership with your mobile device. When you set up a partnership, you select
synchronization and file conversation settings, which are contained in a file on your
desktop computer. This file enables your desktop computer to recognize your device.
4-2
Only devices that have a partnership with a desktop computer can synchronize
information between the two computers.
For more information on partnerships, please refer to your Microsoft ActiveSync
documentation or help file.
Transferring Files:
To transfer files, complete the following steps on the host PC:
9 Select Start> Programs >Communication > (Serial, or USB) Activesync.
9 Double-click on the selected ActiveSync icon
9 After you have established a connection with PDT, tap the “Explore” button at
the top of the ActiveSync window (or select Explore from the File menu).
9 Navigate to the target directory on your PDT and copy the desired file by using
the Copy/paste method or dragging and dropping the desired file(s) into the
folder.
Figure 4-1 Communication
4-3
4.2.2 ActiveSync File Synchronization
ActiveSync files synchronization requires an ActiveSync partnership between the
PDT and the Host PC. Refer to “Setting up a Partnership”, above:
9 Select the files in the synchronization configuration for the PDT partnership.
9 Select Tools > Options from the ActiveSync command bar to configure the
synchronization options.
9 Place the file to be synchronized in the Synchronization folder created you’re
My Documents directory. Defaults to the desktop. During the ActiveSync
connection, all files in the Synchronization folder will be synchronized to the
\My Documents directory on the PDT.
Figure 4-2 Connected
4.3 Networking
Please see the 3.2.14 Owner, Table 3-33 Owner on page 3-45 for setting up the
network ID. And see the 2.5.6 Setting Up Wireless LAN RF to setup the 802.11b
Wireless LAN for RF connecting.
5-1
Chapter 5. Software Applications
5.1 Introduction
The PDT includes Calculator, Inbox,…..
You can switch to any software program by tapping the Start Menu.
5.2 Software Applications
5.2.1 Inbox
Use Inbox to send and receive e-mail messages in the following ways:
9 Synchronize e-mail messages with Microsoft Exchange or Outlook on the
Host Computer.
9 Send and receive e-mail messages by connecting directly to an e-mail server
through an Internet server provider (ISP) or a network.
To setup “Inbox”:
9 Select Start> Programs> Inbox to open it.
9 Select Service> Options from the command bar. Drag the dialog to show the
right edge to configure e-mail.
9 Select “Add…” (Note 1)
9 In the “Service Type” list, select POP3 Mail or IMAP4 Mail. (POP3 is the
most common mail protocol for ISPs).Enter a unique name for e-mail service
in the “Service name” field. This name cannot be changed later.
9 Select “OK”.
9 The Mail Service Setup wizard appears after you add a service. If you are
adjusting the setting of an existing service, select Service> Options, select the
service you are using, and then Properties. In the Service Definition dialog
box, complete the following entries as needed:
¾ Connection: Select the name of the connection you created to connect to
the mail server. If you are receiving e-mail through a network(Ethernet)
connection, select Network Connection. If you want Inbox to use your
current connection, select (none). If you have not created a connection,
select Create new connection. Double-tap the “Make new Connection”
5-2
icon, and follow the instructions in wizard. When finished, select Inbox
in the Taskbar and continue setting up Inbox.
¾ POP3 Host(POP3 only): Enter the name of the mail server you use to
receive and send messages.
¾ Server(IMPA4 only): Enter the name of he mail server you use to
receive and send messages.
¾ User ID: Enter the user name or mailbox ID assigned to you.
¾ Password: Enter the password you use to access this mail account. If
you do not want to be prompted to enter the password each time you
connect, select “Save password”.
¾ Domain(Windows NT): Enter your Windows NT domain name. This
name is required only when connecting to networks, such as a corporate
network, that use Windows NT domain security. This is not required for
most ISP accounts. If you have trouble connecting, try clearing this box.
¾ SMTP Host: If your mail service uses a separate server for SMTP, enter
the name in the box. If you’re setting up a POP3 Mail service with an
ISP, the ISP must use an SMTP mail gateway.
¾ Return Address: By default, the return address is set to
username@POP3host or username@Servername. Depending on the
service you are using. If this is not your e-mail address, enter the correct
address in the box.
9 Set general preferences:
If you are adjusting the setting of an existing service, select Service> Options,
select the service you are using, select Properties, and then select Next. In the
General Preferences dialog box, choose any of the following setting settings, all
of which are optional:
¾ Disconnect service after actions are performed: Select to automatically
disconnect from the server upon completion of all pending actions. This
option minimizes connect time and cost.
¾ Check for new messages every: select the time interval(in minutes) at
which you want the device to check for new mail. If this option is turned off,
you must check for new mail manually by selecting Services>
Send/Receive Mail.
¾ Display a message box when new mail arrives (POP3 only): Select to be
informed that new mail has arrived.
¾ Display a message box when new mail arrives (IMAP4 only): Select to be
informed that new mail has arrived.
¾ Send using MIME format (POP3 only): Select to send messages with
5-3
extended characters.
¾ Only display messages from last 3 days: Select how many day’s messages
you want downloaded.
9 Set inbox preferences
If you are adjusting the settings of an existing service, select Services> Options,
select the service you are using, select Properties, and then select New twice. In
the Inbox Preferences dialog box, choose any of the following options:
¾ Get message headers only: Select to save storage space and time by
downloading only headers. You can download a full copy of the message
later by selecting the message and then Services> Get Full Copy.
¾ Include <number> lines: Select to set the message length (approximate
number of lines) that you want to download.
¾ Get Full Copy of messages: Select to receive a full copy of all messages. In
addition to the message body, any options you select in When getting full
copy will be downloaded. Selecting this option increases the amount of time
needed to download messages.
¾ Only synchronize folder hierarchy under Inbox (IMAP4 only): Select to
speed download time by preventing the complete downloaded of the folder
list every time you connect.
¾ Get meeting requests (POP3 only): Select to download and store copies of
meeting requests when getting full copies of messages. This setting applies
whether you have chosen to download full copies of messages by default, or
you selectively download full copies of messages by opening the message
and selecting Services> Get Full Copy Limitations apply.
¾ Get file attachments (POP3 only): Select to download and save message
attachments when getting full copies of messages. This option may use
significant RAM and slow download time. This setting applies whether you
have chosen to download full copies of messages by default, or if you
selectively download full copies of messages and selecting Services> Get
Full Copy.
¾ Get file attachments and meeting requests (IMAP4 only): Select to
download and store meeting requests and message attachments when getting
full copies of messages. This setting applies you have chosen to download
full copies of messages by default, or if you selectively download full
copies of messages by opening the message and selecting Services> Get
Full Copy Limitations apply.
¾ Only if small than (IMAP4 only): Select to restrict the size of the attachments
you download. Set to 10K if you want to receive meeting requests only.
5-4
9 Include the original message in a reply:
¾ Select Services> Options> Compose tab.
¾ Under Reply, select Include Body. This setting will place a copy of the
original message beneath your response text.
¾ To indent the original message, select Indent.
¾ To add leading characters (such as>) to the original message lines, select
Add leading character, and enter the character you want.
9 Save copies of sent messages:
By default, sent messages are not saved on your device.
¾ Select Services> Options> Compose tab.
¾ Select Keep copy of sent mail in Sent folder.
9 Set the action to follow deleting, moving, or responding to a message:
¾ Select Services> Options > Read tab.
¾ Select desired options.
9 Delete a message:
Select the message and select File> Delete. Messages are moved to Deleted
(local) folder and deleted according to the option you have selected in Services>
Options> Delete tab:
¾ On connect/disconnect: Deletes messages when you connect or disconnect
from your mail service or exit Inbox.
¾ Immediately: Deletes messages as soon as you select File> Delete.
¾ Manual: Deletes messages when you select File> Empty Deleted (local)
Note: If you are working offline, messages that have been deleted from the device the
next time you connect.
9 Empty the Deleted (local) folder:
¾ Select File> Empty Deleted (local). This permanently deletes messages in
the Deleted (local) folder.
¾ To check or adjust the current settings for deleting messages, select
Services> Options> Delete tab.
9 Move or copy a message:
Caution: When you move a message that you have received through POP3 or
synchronization to a folder you created on your device, the copy of the message on
the server is deleted. This prevents duplicate copies of messages. Although the
complete message is moved, message attachments will be deleted if you have not
selected the option to download attachments. Once the message is moved, you will be
able to access the message only from your device.
5-5
¾ Select the message
¾ Select File> Move To or File> Copy To.
¾ Select the destination folder. If you are working offline, the message will be
moved or copied from the server the next time you connect.
9 Folder-
Create a folder:
¾ Select File> Folder> New Folder
¾ Type a name for the folder.
Delete a folder:
¾ Select the folder you want to delete
¾ Select File> Delete
Designate a folder as offline:
Only IMAP4 folders can be designated as offline. All IMAP4 default folders,
such as Inbox, are automatically designated as offline. Messages in offline
folders can be viewed when you are disconnected from your mail server. If a
folder is not designated as offline, you will be able to read and respond to
messages in that folder only when connected to the server.
¾ To designate a folder as offline, select the folder and then select Service >
Offline Folder.
Rename a folder:
¾ Select the folder you want to rename.
¾ Select File> Folder> Rename Folder.
¾ Type the new name for the folder.
Notes:
z Default folders, such as Inbox, can’t be renamed.
z Folders you create for IMAP4 mail servers can’t be renamed.
Synchronize folders while connected:
When you synchronize folders, the contents of your device folders and mail
server folders are compared and updated. New mail messages are downloaded,
and messages in your device Outbox folder are sent. The synchronization
behavior depends on how you connect to your mail server.
¾ When you connect to a POP3 server, the Inbox and Outbox folders on
your device are synchronized with the corresponding folders on the mail
server. To synchronize after the initial connection, select Services>
Send/Receive Mail.
¾ When you connect to an IMAP4 server, Inbox, Outbox, and all folders
5-6
marked as offline are synchronized. To synchronize all folders after the
initial connection, select Services> Synchronize Folders. To
synchronize just the selected folder and the Outbox folder, select
Services> Send/Receive Mail.
9 Compose and send a message:
¾ In list view, select Compose> New Message
¾ Enter the address of one or more recipients, separating them with a
semicolon. If the recipient is listed in the Address Book, enter a few
letters of the recipient’s name and select Compose> Check Name. If
there is only one match, the e-mail address is inserted. If there is more
than one match, select the correct address from the Choose E-mail
Recipients dialog box. If there is no match then add a new e-mail address
through Choose E-mail Recipients.
¾ To attach a file, select File> attachments> Add Attachment.
¾ Select File> Send. If you are working offline, the message is moved to
the Outbox folder and will be sent the next time you connect.
Tip: to see more header information, select the triangle in the lower-right corner of
the header area. Select the triangle again to collapse the header area.
9 Save a message:
¾ Select File> Save to save the message you are composing or editing.
The message is not sent and is saved in the inbox folder of the active service.
9 Reply to or forward a message:
¾ Open the message, and then select Compose> Reply to Sender, Reply to
All, or Forward.
¾ Enter your response.
¾ Select File> Send.
Tips:
z Selections in the Options dialog box determine whether the original text is
included.
z To see more header information, select the inverted triangle in the lower-right
corner of the header area. Select the triangle again to collapse the header area.
9 Check Inbox status:
¾ In list view, select Compose> Status. You can view details such as the
number of messages to be sent, deleted, and copied, and the number of
attachments to be downloaded.
9 Download message from the server:
When you download messages, you need to create two connections: a remote
5-7
connection and a mail server connection. The remote connection connects you
and your ISP or network. The mail server connection downloads messages from
your mail server to Inbox on your device. When you select Services> Connect in
Inbox, Inbox starts a remote connection using the connection you specified when
setting up the current mail service. If you are already connected through a remote
connection other than the one you specified in the service, you will be asked if
you want to use the current connection. If you choose not to, you will need to
disconnect from the current connection before you can check for new messages.
¾ Select the Services menu and make sure that the service you want to use
is selected (the selected service has a bullet next to it.)
¾ Select Services> Connect. The messages on your device and mail
server are synchronized: new messages are downloaded to the device
Inbox folder, messages in the device Outbox folder are sent, and
messages that have been deleted on the server are removed from the
device Inbox. Double-tap a message list to open it.
¾ If you read a message and decide that you need the full copy, select
File> Get Full Copy while in the message window or Services> Get
Full Copy while in list view. This will also download message
attachments and meeting requests if you have those options selected in
the Inbox Preferences dialog box. You can also choose to download
full copies of messages by default.
¾ When finished, select Services> Connect to disconnect. You also need
to disconnect your dial-up connection by double-tapping the icon in the
status bar and selecting Disconnect.
Notes:
z Receiving entire messages consumes storage memory.
z The size column in the Inbox list view displays the local size and server size of
a message. Even when a message has been downloaded fully, these numbers
may differ because the size of a message can very between the server and the
device.
z When using IMAP4 to get Outlook + data, you will see the contents of your
Journal folder. File editing transactions and documents (such as Task items,
e-mail message, and Word documents) attached using drag and drop will appear
as shortcuts on the device. A copy of the document will not be moved to your
device, and the shortcut on the device cannot be used to access the documents
associated with a journal entry to the device, attach the document to the entry
rather than dragging and dropping it. Also, be sure to set your IMAP4 service to
5-8
receive full copies of messages, attachments, and meeting requests. For more
information on using Journal, see the Help for the desktop version of Outlook.
9 Working with Message Attachments:
¾ If you receive messages through a remote mail server, in Inbox on the device,
select the Get file attachments and meeting requests (IMAP4) or Get
meeting requests (POP3) setting in the Inbox Preferences dialog box. For
more information, see Set Inbox preferences.
Notes:
z Embedded images and OLE objects cannot be received as attachments
z Embedded messages can be viewed as an attachment when using IMAP4 to
receive e-mail. However, this features does not work if TNEF is enabled so
that you can receive meeting requests.
9 Check attachments status:
¾ An attachment sent with an e-mail message, whether it has been downloaded
or not, will appear as an icon at the bottom of the message in its own window
pane. If you don’t see this pane, select File> Attachments> Show
Attachments. If TNEF is turned on so you can receive meeting requests, you
will not see attachments until they are fully downloaded.
¾ To mark an attachment for downloading in a POP3 or IMAP4 service,
double-click it. The attachment will be downloaded the next time you
connect. You can also set Inbox to download attachments automatically when
you get a full copy of a message. For more information, see Receive
attachments.
9 Open an attachment:
¾ With the message open, double-tap the attachment’s icon at the bottom of the
message. If you don’t see this pane, select File> Attachments> Show
Attachments.
9 Store an attachment:
¾ Select Service> Options> Storage tab.
¾ Select to store attachments on internal RAM or a storage card.
¾ If you use more than one storage card, select it from the list.
Note: Once you make the above selection, all attachments will be moved to the
selected card.
9 Delete an attachment:
¾ To delete an attachment from a message you are sending, select the
attachment, and then select Edit> Clear or press the DEL key on the
keypad.
5-9
¾ To delete an attachment you have received, delete the message.
9 Attach a file to a message:
¾ With the message open, select File> Attachments> Add Attachment.
¾ Select the file you want to attach.
Note:
OLE objects cannot be attached to Inbox messages.
Note 1: To add a mail service, select “Add”, To remove a mail service, select the
service from the Installed service box and select “Remove”. To view a mail service’s
properties, select the service from the Installed service box and then select
Properties.
Figure 5-1 Inbox
5-10
5.2.2 Internet Explorer
With Internet Explorer, you can view Web or intranet Web pages on your device. You
will need to use a modem or WLAN to connect to an Internet server provider (ISP) or
network.
5.2.2.1 Connect to the Internet
Before you can view Web pages, you must
set up a remote connection to your ISP or
network.
5.2.2.2 Start Internet Explorer
9 Open Internet Explorer by selecting Start
> Programs > Internet Explorer.
9 To get default home page, navigate to the
desired default web page.
9 Select View > Internet Options from the
command bar.
9 Enter the desired URL in the Start page
field.
9 Press the OK button.
Figure 5-2 Internet Explorer
5.2.2.3 Navigation Control
Internet Explorer uses sliding menus for application and navigation control. Tap and
drag the sliding menus to the left or right to see the hidden menu items and toolbars.
To achieve more screen real estate in Internet Explorer, you can hide the Status bar
and View menu. From the top menu bar, go to View > Hide Toolbars.
Once it is hidden, you must cold reset to access these features again. Refer to 2.7.2
“Cold Reset “for more information.
5.2.2.4 Set up a proxy server
Proxy servers are often used when connecting to the Internet through a local network,
such as a corporate network, for added security.
9 Select View > Internet Options > Connection Tab.
9 Select Access the Internet using a proxy server.
9 Enter the proxy server address and port. For more information, see your
administrator.
9 To bypass the proxy server for local address, such as corporate intranet pages,
select Bypass proxy for local address.
5-11
5.2.2.5 Enable Cookies
A cookie file contains information about your identity and preferences so that a
Web site can tailor information to your needs. The Web site sends the file and it
is stored on your mobile device.
9 Select View > Internet Options > Security Tab.
9 Select Allow cookies.
5.2.2.6 Search for an Internet Site
9 Select View > Go > Search to search the web.
5.2.2.7 Go to an Internet address
9 Select Address Bar, if necessary to display the Address bar
9 Enter the address
9 Press “ENTER” key.
5.2.2.8 View previously visited sites
9 Tap the Arrow button at the right site of Address Bar
9 Select the Web Address you want to view.
5.2.2.9 Add and view Favorites
9 Go to the page you want add
9 Select Favorites > Add To Favorites.
9 If necessary, locate the folder you want.
9 Confirm or change the name.
9 To view your favorite Web sites, select Favorites and the Web site you want
to view.
Note:
To organize your Favorites list, select Favorites > Organize Favorites.
5.2.2.10 Browse Web pages
9 To move to a page you have previously view, select View > Back
9 To move to the next page (provided you have viewed it previously), Select
View > Forward.
9 To return to your Home page, select View > Go > Home.
5.2.2.11 Refresh current page
9 Select View > Refresh.
5-12
5.2.2.12 Stop loading a page
9 Select View > Stop.
5.2.2.13 View current page
9 Select View > Internet Options
9 To view the protocol, page type, size, and address, selects the General tab.
9 To view security information about the page, select the Security tab.
5.2.2.14 View HTML source code
9 While viewing the page, select File > Save As and save the file as .txt file.
9 Open the file in a word processing program, such as WordPad.
5.2.2.15 Change home and search page settings
9 Open the page you want to use as your home or search page.
9 Select View > Go > Home or Search.
5.2.2.16 Save a copy of current page
You can save Web pages and view them later when you’re disconnected from the
Internet or Intranet without using cached memory.
9 Select File > Save As
9 Specify a folder location and give the file name.
5.2.2.17 Copy a Web page to a document
9 Select all or part of the Web page you want to copy.
9 Select Edit > Copy.
9 Go to the document where you want to place the information and select the
location.
9 Select Edit > Paste.
5.2.2.18 Select security Options
9 Select View > Internet Options > Security tab
9 Select the security protocols you want.
5.2.2.19 Change the font size
9 Select View > Text Size and select the desired size.
5-13
5.2.3 Media Player
The PDT comes with Media Player for
Windows CE.NET installed.
9 Open Media Player by selecting
Start > Programs > Media
Player from the desktop.
9 Select File > Open to open a new
media file.
9 Please refer to
www.microsoft.com for additional
information and help with your
Microsoft Windows Media Player.
Figure 5-3 Media Player
5.2.4 Messenger
The Windows CE Messenger client application in Windows CE.NET allows you
to communicate real-time using text-based messaging, VOIP, and more.
9 See who’s online. See when your colleagues are online. You can also post
your presence information to a list of watchers that you define.
9 Talk instead of type Stop typing Talk with a colleague anywhere in the
world using the microphone and speakers on your device. Windows
Messenger supports high-quality voice calling r Windows CE device.
9 Communicate using Session Initiation Protocol (SIP) or Hotmail contacts
Windows Messenger supports. Communication with your colleagues in the
enterprise with a SIP based communications service. You can also talk to
your Hotmail contacts using the .NET Messenger.
5.2.5 Microsoft WordPad
You can create and edit documents and templates in WordPad, using buttons and
menu commands that are similar to those used in the desktop version of
Microsoft Word. You can work with files Normal or Outline view.
WordPad documents are usually saved as .pwd files, but you can also save
documents in other file formats, such as .rtf or .doc.
5-14
5.2.5.1 Selecting and Editing Text
9 Select text
To select Do this
Any amount of text Drag the stylus over the text.
A word Double-tap the word.
A single paragraph Triple-tap within the paragraph.
An entire document Select Edit > Select All
An picture Tap the picture
9 Find text
¾ To search for text in one part of a document, select that part. Otherwise, the
whole document is searched.
¾ Select Edit > Find
¾ Enter the text you want to find. For a paragraph, enter ^p. For a tab stop,
enter ^t.
¾ Select the search options you want.
¾ To continue searching, select Edit > Find > Next.
9 Replace text
¾ To replace text in one part of document, select that part. Otherwise, the
whole document is searched.
¾ Select Edit > Replace.
¾ Enter the text you want to find and the text you want to replace it with. For
a paragraph, enter ^p. For a tab stop, enter ^t.
¾ Select the replacement options you want.
¾ Select Find Next.
¾ On the Find/Replace toolbar, select the appropriate button.
9 Move, copy, or delete text
¾ Select the text you want to move, copy, or delete.
¾ To move or delete text, select the Cut button. To copy the text, select the
Copy button.
¾ To paste the information, move the insertion point to the desired location,
and select the Paste button.
Notes:
5-15
z To undo an action, select Edit > Undo.
z To restore the action, select Edit > Redo.
5.2.5.2 Formatting Text
9 Create bulleted and numbered lists
¾ Select the Bullets or Numbering button.
¾ Type the first item.
¾ Press ENTER, type the next item, and repeat as needed.
¾ Select the button again to end list formatting.
Note: To change the number style for the selected list, select Format > Paragraph,
In the Format list, select the style you want.
9 Set the default font
¾ Select Format > Font.
¾ Select the font you want.
¾ Select Set As Default
¾ To confirm that your changes will be applied to subsequent documents you
create, select Yes.
Note: To apply the default font and stylus to selected text, select Apply Default.
9 Select a different font
¾ Select the text you want to change. To select all text, select Edit > Select All.
¾ From the Font list, select the font you want.
¾ From the Font Size list, select a size.
Note: To see more formatting options, select Format > Font.
9 Change font formatting
¾ Select desired text.
¾ Select the Bold, Italic, or Underline button.
¾ To change the color, select Format > Font and select the color you want from
the Color list.
9 Adjust the paragraph alignment
¾ Select the paragraph you want to align.
¾ Select the Align Left, Center, or Align Right button.
Note: To see more formatting options, select Format > Paragraph.
9 Indent a paragraph
¾ Select the paragraph you want to indent.
¾ Select Format > paragraph.
5-16
¾ Adjust the indentation settings as needed.
9 Set tabs
¾ Select Format > Tabs.
¾ Change the tab settings as needed.
5.2.5.3 Adjusting the Display
9 Wrap text in the window
¾ Select View > Wrap to Window.
9 Display the document using the full screen
¾ Select View > Full Screen.
¾ To exit Full Screen view, select Restore.
¾ To move the Restore button, drag the bar on the left side.
9 Display or hide scroll bars
¾ Select View > Horizontal Scroll Bar or Vertical Scroll Bar.
9 Zoom in or out
¾ Select View > Zoom, and select the desired percentage.
Note: For Custom, enter the exact percentage and select OK.
5.2.5.4 Working in Outline View
9 Switch between Normal and Outline views
¾ Select View > Normal or Outline.
9 Assign and change outline levels
¾ Select View > Outline.
¾ Select the appropriate buttons on the toolbar.
5.2.5.5 Inserting Symbols
9 Place the insertion point where you want to insert the symbol.
9 Select Tools > Insert Symbols.
9 Select the symbol you want, and then select Insert.
Tips:
If you select a different font ( or subset of a font), a different set of Symbols will
be displayed.
5-17
5.2.5.6 Printing a Document
9 Select File > Print.
9 Select the printing options you want.
Tips:
z Port list the available printer ports
z If Network is selected from the Port list, enter the path to the network
printer to the Net Path box.
5.2.5.7 Setting a password for a Document
9 Select File > password.
9 Type and verify the password.
9 You must save the document (File > Save) to return the password.
5.2.5.8 Converting Documents
9 About document conversion
If an e-mail program is installed on your device and you receive an attached
Word document or template created in Word version 6.0 or later, WordPad will
convert the file on your device. To view the document, simply open the
attachment in your e-mail program or open the file in the WordPad.
During conversion, some formatting attributes may be changed or lost. To avoid
losing these attributes permanently, close the file after viewing it rather saving
the file on your device. If you save the file, save with a different file name.
For more information about conversion performed on your device, see the
following topics.
9 Changes caused by Word document conversion
¾ Formatting
z Borders and Shading
Borders and shading are not displayed in WordPad, but are restored when
converted back to a Word document. Shading is not restored when used in a
table, but simple borders are restored.
z Character formatting
Bold, italic, strikethrough, superscript, subscript, and hidden text are
retained and displayed. Other effects are changed or removed.
z Colors
Colors are retained and mapped to colors available on your device.
5-18
z Fonts and font sizes
Fonts not supported by your mobile device are mapped to the closest font
available in WordPad.
z Page Formatting
Headers, footers, footnotes, columns, pages setup information, and style
sheets are removed during conversion to WordPad. WordPad supports
built-in headings.
z Paragraph formatting
Tabs, alignment, bullets, indentation, simple numbered lists, and paragraph
spacing are retailed and displayed in WordPad.
¾ Pictures
Pictures are removed during conversion.
¾ Table of Contents
Table of Contents text and some formatting are preserved. However, any text set
at right-aligned tab stops may wrap to the next line.
¾ Index
Index text and some formatting are preserved.
¾ Tables
Tables appear as tab-delimited text. Cells containing wrapped text, tabs, or
paragraph markers may be difficult to read. Simple tables are displayed
accurately and restored when you convert the WordPad file back to a WordPad
document.
¾ OLE Objects
OLE Objects are removed during conversion.
¾ Revisions marks, annotations, and comments
Revision marks are visible but cannot be changed. Annotations and documents
are removed during conversion.
5-19
5.2.6 Remote Connection
Using Remote Desktop Connection, you can log on to Windows Terminal Server and
use all programs installed on this server. For example, instead of running Microsoft
Pocket Word, you can run the desktop version
of Microsoft Word.
5.2.6.1 Connecting to Terminal Server
9 Select Start > Programs > Remote
Connection, or run ‘CETSC’ from the
command prompt.
9 In the Server box, type or select a
Terminal Server name or TCP/IP address,
or select a server in the drop-down list.
9 Select Connect.
9 In the Remote Connection window, type
your user name, password, and domain(if
required), and then select OK.
Figure 5-4 Remote Connected
5.2.6.2 Disconnecting Without Ending a Session
9 In the Remote Connection window, select Start > Shutdown.
9 Select Disconnect > OK.
Note: If you previously disconnected from a Terminal Server without ending the
session, the Terminal Server will continue to execute any running processes and
Remote Connection can later reconnect to this same session(if your
administrator has configured Remote Connection to reconnect to disconnected
sessions).
5.2.6.3 Disconnecting and Ending a Session
9 In the Remote Connection window, select Start > Shutdown.
9 Select Log Off > OK.
5-20
5.2.7 Windows Explorer
Windows Explorer works almost the same on
your PDT as it does on your PC. See the
topics below for information about the
difference in Windows Explorer on your
device.
5.2.7.1 Navigating in File View
9 Go forwards and Back
¾ To go to the previous folder, select
Go > Back.
¾ To go to the next folder (which you
have just viewed), select Go >
Forward.
Figure 5-5 Windows Explorer
9 Use the Go menu
¾ To quickly access the My Documents folder, select Go > My Documents
¾ To see all of the folders you have accessed, select Go > History. Double-tap
a folder to return to it.
5.2.7.2 Viewing Files as Icons Lists
9 To view icons, select View > Large Icons or Small Icons.
9 To view a list, select View > Details.
5.2.7.3 Working with Files and Folders
9 Create a new folder
¾ If necessary, open the folder where you want the new folder to reside.
¾ Select File > New Folder.
9 Add a folder to your Favorites list
¾ Open the folder
¾ Select Favorites > Add to Favorites.
¾ In the Name box, type the shortcut name.
Tips:
z To open a favorite file or folder, select Favorites and then select the folder.
z To organize your favorites, select Favorites > Organize Favorites.
9 Transfer a file using infrared
¾ To send a file, select it, line up the infrared ports, and select File > Send To
5-21
> Infrared Recipient.
¾ To receive a file, line up the infrared ports, and select File > Receive.
5.2.7.4. Creating Desktop Shortcuts
9 Display the file or Web page for which you want to create a Shortcut.
9 Select File > Send to.
9 Select Desktop as Shortcut.
5.2.7.5 Switch to Internet
9 Type a URL in the Address bar.
5-22
5.3 DiskOnChip
The DiskOnChip let the application or a data file can be stored into the Flash
Memory.
Note: The DiskOnChip storage memory persists all reset (warm/cold reboot)
conditions and software/firmware updates.
We strongly recommends installing all applications, applets, programs, and
important data files to the DiskOnChip Flash location.
Caution:
If an application or a data file is only installed or saved in RAM, a hard
reset will result in the loss of that application or data file.
5.3.1 Saving to Flash
To save an application or data to the Flash Memory, from your current
application, select File > Save As > navigate to the DiskOnChip location and
save it.
5.3.2 DiskOnChip Location
To access the contents of DiskOnChip storage:
9 Double-tap the My Computer icon on the desltop.
9 Double-tap the DiskOnChip icon to view DiskOnChip.
Figure 5-6 DiskOnChip
5-23
5.3.3 DiskOnChip Size
The size of the DiskOnChip will vary,
depending on the size of system
firmware.
9 Inside the DiskOnChip directory,
tap File > Properties.
9 The DiskOnChip Properties
dialog:
The number following Free is the
amount of memory currently available on
your device.
Figure 5-7 DiskOnChip Size