Shure orporated AD1G57 Non-Broadcast Transmitter Worn on Body User Manual Exhibit D Users Manual per 2 1033 c3
Shure Incorporated Non-Broadcast Transmitter Worn on Body Exhibit D Users Manual per 2 1033 c3
Exhibit D Users Manual per 2 1033 c3
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3433902 |
| Application ID | fO9wRfd1fNBrg4HFo2XBFA== |
| Document Description | Exhibit D Users Manual per 2 1033 c3 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 121.2kB (1514997 bits) |
| Date Submitted | 2017-06-21 00:00:00 |
| Date Available | 2017-06-21 00:00:00 |
| Creation Date | 2016-09-01 14:15:30 |
| Producing Software | Adobe PDF Library 15.0 |
| Document Lastmod | 2016-09-20 13:36:53 |
| Document Title | Exhibit D Users Manual per 2 1033 c3 |
| Document Creator | Adobe InDesign CC 2015 (Windows) |
AXIENT DIGITAL AF 9. 1. 16 AD1 TRANSMITTER USER GUIDE Š 2016 Shure Incorporated 27A (Rev. 1) Printed in China Important Product Information LICENSING INFORMATION Licensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible requirements. Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing of Shure wireless microphone equipment is the userâs responsibility, and licensability depends on the userâs classification and application, and on the selected frequency. Shure strongly urges the user to contact the appropriate telecommunications authority concerning proper licensing, and before choosing and ordering frequencies. Information to the user This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ⢠Reorient or relocate the receiving antenna. 16 ⢠Increase the separation between the equipment and the receiver. ⢠Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. ⢠Consult the dealer or an experienced radio/TV technician for help. 1. Note: EMC conformance testing is based on the use of supplied and recommended cable types. The use of other cable types may degrade EMC performance. Please follow your regional recycling scheme for batteries, packaging, and electronic waste. 9. This device complies with Industry Canada licence-exempt RSS standard(s). Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prĂŠsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisĂŠe aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioĂŠlectrique subi, mĂŞme si le brouillage est susceptible d'en compromettre le fonctionnement. AF WARNING: Danger of explosion if battery incorrectly replaced. Operate only with Shure compatible batteries. Note: Use only with the included power supply or a Shure-approved equivalent. WARNING ⢠Battery packs may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify, disassemble, heat above 140°F (60°C), or incinerate. ⢠Follow instructions from manufacturer ⢠Only use Shure charger to recharge Shure rechargeable batteries ⢠WARNING: Danger of explosion if battery incorrectly replaced. Replace only with same or equivalent type. ⢠Never put batteries in mouth. If swallowed, contact your physician or local poison control center ⢠Do not short circuit; may cause burns or catch fire ⢠Do not charge or use battery packs other than Shure rechargeable batteries ⢠Dispose of battery packs properly. Check with local vendor for proper disposal of used battery packs. ⢠Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like Australia Warning for Wireless This device operates under an ACMA class licence and must comply with all the conditions of that licence including operating frequencies. Before 31 December 2014, this device will comply if it is operated in the 520-820 MHz frequency band. WARNING: After 31 December 2014, in order to comply, this device must not be operated in the 694-820 MHz band. AD1 Axient Digital Bodypack Transmitter The AD1 transmitter delivers superior audio performance in a compact, lightweight package. Efficient, ultra-linear RF performance maximizes the number of channels on-air in crowded RF environments. Advanced power management provides extended, rechargeable battery life and highly accurate status metering. Features ⢠All-digital signal path delivers superior audio clarity and quality ⢠Ultra-linear RF performance places more channels on-air ⢠IR Sync function automatically tunes transmitter to the receiver frequency ⢠Shure lithium-ion rechargeable battery delivers up to 8 hours of runtime from a single charge ⢠Advanced control menu to adjust frequency and audio settings from the transmitter ⢠Lockable user interface prevents accidental or inadvertent changes to controls once settings are made ⢠Compatible with all Shure wireless microphones that have a TA4F connector. 16 ⢠LEMO connector model available for use with LEMO connector microphones Optional Accessories Dual-band flexible antenna WA340 Transmitter carrying case WA610 Zipper bag 26A13 Belt clip 44A12547 AXT910 Y-Cable for bodypack transmitters AXT652 LEMO Y-cable for bodypack transmitters AXT652LEMO3 Dual-band flexible antenna AXT642 Portable bodypack charging station AXT903 3-AA Battery Sled for AXT100 bodypack transmitter AXT913 Instrument cable WA302 Replacement belt clip 44A12547 Instrument cable with right angle 1/4" connector WA304 Mute Switch for Bodypack WA661 Mute Switch for 2 Bodypacks WA662 AF Threaded TAF4 adapter Bodypack rechargeable lithium-ion battery 1. Bodypack rechargeable lithium-ion battery (2) 9. Included Components AD1 Transmitter Overview â RF Antenna For RF signal transmission. ⥠Display: View menu screens and settings. Press any control button to activate the backlight. ⣠Control Buttons Use to navigate through parameter menus and change values. ⤠Battery Compartment Requires Shure SB900 rechargeable battery or 2 AA batteries. ⼠AA Battery Adapter Remove to accommodate a Shure SB900 battery ⌠SMA Connector Connection point for RF antenna. ⧠On/Off Switch Powers the unit on or off. 10 ⨠Power LED 9. -- Green = unit is powered on -- Red = low battery or battery error (see Troubleshooting), Mute Mode enabled 1. 16 ⢠Infrared (IR) Port Align with the receiver IR port during an IR Sync for automated transmitter programming. ⊠Input Jack -- Connects to a 4-Pin Mini Connector (TA4F) microphone or instrument cable. -- Connects to a LEMO connector Transmitter Controls Clip the transmitter to a belt or slide a guitar strap through the transmitter clip as shown. Use to navigate through parameter menus and change values. AF Wearing the Bodypack Transmitter For best results, the belt should be pressed against the base of the clip. exit enter exit Acts as a 'back' button to return to previous menus or parameters without confirming a value change enter Enters menu screens and confirms parameter changes â¨â§ Use to scroll through menu screens and to change parameter values Locking the Controls Lock transmitter controls to prevent accidental or unauthorized changes to parameters. The lock icon is shown on the home screen when the control lock in enabled. 1. From the Utilities menu, navigate to Lock and selection one of the following: -- Yes: Locks the controls -- No: Unlocks the controls 2. Press enter to save. To quickly unlock a transmitter: Press enter, select Yes, and press enter. Battery Installation AA SB900 ULXD1 ULXD1 65A15224 â Accessing the Battery Compartment Press the side tabs on the bodypack or unscrew the cover on the handheld as shown to access the battery compartment. 16 ⥠Installing Batteries Setting the AA Battery Type AA Battery Installation Fully insert the batteries as shown to ensure proper battery contact and to allow the door to latch securely. 9. To ensure accurate display of transmitter runtime, set the battery type in the transmitter menu to match the installed AA battery type. If a Shure SB900 rechargeable battery is installed, selecting a battery type is not necessary and the battery type menu will not be displayed. 1. -- AA Batteries: Place batteries (note polarity markings) and AA Adaptor as shown -- Shure SB900 Battery: Place battery as shown (note polarity markings), remove AA Adaptor from bodypack transmitter, stow AA Adaptor in door for handheld transmitter Note: If using AA batteries, set the battery type using the transmitter menu. AF 1. Press the menu button to navigate to the battery icon. 2. Use the âźâ˛ buttons to select the installed battery type: -- AL = Alkaline -- nH = Nickel Metal Hydride -- Li = Lithium Primary 3. Press enter to save. Battery Info Chem: NiMH Battery Info Chem: Alkaline Battery Info Chem: Lithium Correct Incorrect Shure SB900 Rechargeable Battery Shure SB900 lithium-ion batteries offer a rechargeable option for powering the transmitters. Batteries quickly charge to 50% capacity in one hour and reach full charge within three hours. Single chargers and multiple bay chargers are available to recharge the Shure batteries. Caution: Only charge Shure rechargeable batteries with a Shure battery charger. Shure SB900 Runtime 1 mW >11 hours 10 mW >11 hours 20 mW >7 hour Checking Battery Info When using an SB900 rechargeable battery, the receiver and transmitter home screens display the number of hours and minutes remaining. Detailed information for the SB900 is displayed in the receiver Batt Info menu and the transmitter menu: Utilities > Batt Info 16 ⢠Time: Battery runtime ⢠Health: Percentage of current battery health ⢠Charge: Percentage of change ⢠Cycles: Record of the number of charging cycles for the installed battery 1. ⢠Temp: Battery temperature in Fahrenheit and Celsius ⢠mAh: Remaining mAh for the installed battery 9. Important Tips for Care and Storage of Shure Rechargeable Batteries Proper care and storage of Shure batteries results in reliable performance and ensures a long lifetime. ⢠Always store batteries and transmitters at room temperature ⢠Ideally, batteries should be charged to approximately 40% of capacity for long-term storage AF ⢠During storage, check batteries every 6 months and recharge to 40% of capacity as needed For additional rechargeable battery information, visit www.shure.com. AA Batteries and Transmitter Runtime Transmitters are compatible with the following AA battery types: ⢠Alkaline ⢠Nickel Metal Hydride (NiMH) ⢠Lithium Primary A 5-segment battery indicator representing the charge level of the transmitter battery is displayed on the screens of the transmitter and receiver. The following tables contain the approximate remaining transmitter runtime in hours:minutes. Alkaline Batteries: Up to 9 Hours of Runtime Battery Indicator Approximate Runtime Remaining (hours:minutes) NiMH Batteries: Up to 10 Hours of Runtime Battery Indicator Approximate Runtime Remaining (hours:minutes) Lithium Primary Batteries: Up to 16 Hours of Runtime Battery Indicator Approximate Runtime Remaining (hours:minutes) 9:30 to 7:30 10:00 to 8:00 16:00 to 12:45 7:30 to 5:30 8:00 to 6:00 12:45 to 9:30 5:30 to 3:30 6:00 to 4:00 9:30 to 6:30 3:30 to 2:30 4:00 to 2:00 6:30 to 3:15 2:30 to 1:30 2:00 to 0:20 3:15 to 0:20 < 0:30 0:20 to 0:00 0:20 to 0:00 Main Menu Parameters The Main Menu organizes the available transmitter parameters into three categories: ⢠Radio ⢠Audio ⢠Utilities To change a parameter, press the enter button to enable editing and use the arrow buttons to change values or settings. When finished, press enter to save. Radio Menu Audio Menu Utilities Menu Group and Channel Press the enter button to enable editing of a group (G:) or channel (C:). Use the arrow buttons to adjust the values. MicOfs Adjust Mic Offset level to balance mic levels when using two bodypacks for frequency diversity. Device ID Assign a device ID of up to 9 letters or numbers. Pad Adjust the pad to avoid overloading the audio input. Lock Locks the transmitter controls and power switch. RF Output -- Pos: Positive pressure on microphone diaphragm produces positive voltage on pin 2 (with respect to pin 3 of XLR output) and the tip of the TRS output. -- Neg: Positive pressure on microphone diaphragm produces negative voltage on pin 2 (with respect to pin 3 of XLR output) and the tip of the TRS output. MuteMode When enabled, the power switch is configured as a mute switch for the audio: 9. -- On: RF signal is active -- Mute: RF signal is inactive Drop Mark When enabled, press the enter button to drop a marker in Wireless Workbench or Shure ChannelsPlus. 16 RF Power Higher power settings can extend the range of the transmitter. PolarityPos Selectable polarity assignment for LEMO connector transmitters: Versions Displays transmitter information: 1. Frequency Press the enter button once to edit the first 3 digits, or twice to edit the second 3 digits. -- Power switch on: audio signal on -- Power switch off: audio signal muted AF Tone Transmitter will generate a continuous test tone. The tone can be set to 400 Hz or 1000 Hz. Level When enabled, allows for adjustment of the output level of the test tone. Tips for Editing Menu Parameters -- FW: Installed firmware -- HW: Hardware version -- SN: Serial number Batt Info Displays battery information: -- Time: Battery runtime -- Health: Percentage of current battery health -- Charge: Percentage of change -- Cycles: Record of the number of charging cycles for the installed battery -- Temp: Battery temperature in Fahrenheit and Celsius -- mAh: Remaining mAh for the installed battery Reset All Restores all transmitter parameters to factory settings. ⢠To access the menu options from the home screen, press the menu button. Each additional press of the menu button advances to the next menu screen. ⢠A menu parameter will blink when editing is enabled ⢠To increase, decrease or change a parameter, use the arrow buttons ⢠To save a menu change, press enter ⢠To exit a menu without saving a change, press menu RF Mute Power-on RF Mute RF Mute prevents transmission of the audio by suppressing the RF signal, while allowing the transmitter to remain powered-on. The message RF Mute is shown on the home screen. Power-on RF Mute places the transmitter in RF Mute mode immediately when turned on. ⢠Starting with the transmitter off, press and hold the exit button, and then switch on the power ⢠Continue to hold the exit button until the RF Muted message appears on the home screen RADIO RF Output: Mute 1. From the Radio menu, navigate to RF Output. Tx Overload 2. Choose one of the following options: -- On: RF signal is active -- Mute: RF signal is disabled Turning the transmitter off and on, or replacing the battery will restore RF Output to On. Scan and Sync Use this procedure to tune a receiver and transmitter to the best open channel. Important! Before you begin: 16 The Tx Overload message is displayed when the audio input of the transmitter experiences an overload. 3. Press enter to save. 1. Turn off all transmitters for the systems you are setting up. (This prevents them from interfering with the frequency scan.) ⢠Other wireless systems or devices ⢠Computers ⢠CD players ⢠Large LED panels 9. Turn on the following potential sources of interference so they are operating as they would be during the presentation or performance (the scan will detect and avoid any interference they generate). AF ⢠Effects processors 1. Press the channel number button to select a receiver channel. 2. Power on the transmitter. 3. Press the sync button on the receiver. 4. Align the IR windows until the receiver IR port illuminates red. Note: When complete, SyncSuccess! appears. The transmitter and receiver are now tuned to the same frequency. Linking Two Transmitters to a Receiver Linking two transmitters to a receiver offers the flexibility to provide a performer with either a handheld or bodypack transmitter to meet their preference. For performances requiring instrument changes, two bodypack transmitters can be linked to a single receiver. Note: Only turn on and operate one transmitter at a time to prevent interference between the transmitters. Syncing the Transmitters to the Receiver Both transmitters must be individually linked to the receiver by performing an IR Sync. 1. Turn on the first transmitter and perform an IR Sync with the receiver. 2. Perform a sound check and adjust the transmitter gain if necessary. When finished, turn off the transmitter. 3. Turn on the second transmitter and perform an IR Sync with the receiver. 4. Test the transmitter at performance conditions and adjust the transmitter gain if necessary. When finished, turn off the transmitter. Matching Audio Levels with Mic Offset When linking two transmitters to a receiver, there may be a difference in volume levels between microphones or instruments. If this occurs, use the MicOfs function to match the audio levels and eliminate audible volume differences between transmitters. If using a single transmitter, set MicOfs to 0 dB. 1. Turn on the first transmitter and perform a sound check to test the audio level. Turn off the transmitter when finished. 2. Turn on the second transmitter and perform a sound check to test the audio level. 3. If there is an audible difference in the sound level between the transmitters, navigate to the MicOfs menu on the transmitter to increase or decrease the Mic Offset in realtime to match the audio levels. Updating Firmware Firmware is embedded software in each component that controls functionality. Periodically, new versions of firmware are developed to incorporate additional features and enhancements. To take advantage of design improvements, new versions of the firmware can be uploaded and installed using the Firmware Update Manager tool available in Shure's Wireless WorkbenchÂŽ 6 (WWB6) software. Software is available for download from http://www. shure.com/wwb. Firmware Versioning When updating receiver firmware, update transmitters to the same firmware version to ensure consistent operation. The firmware of all ULX-D devices has the form of MAJOR.MINOR.PATCH (e.g., 1.2.14). At a minimum, all devices on the network (including transmitters), must have the same MAJOR and MINOR firmware version numbers (e.g., 1.2.x). Updating the Transmitter 1. To upload the firmware to the transmitter, go to Device Configuration > Tx Firmware Update on the receiver. 2. Place the transmitter on its side and align the IR ports. 16 3. Press ENTER on the receiver to begin the download to the transmitter. IR ports must be aligned for the entire download, which can take 50 seconds or longer. 1. Specifications AD1 Bodypack Transmitter Weight 146.6 g (5.2 oz.), with batteries RF Carrier Frequency Range Housing 470â814 MHz Note: varies by region 9. Cast aluminum Operating Temperature Range Working Range Under typical conditions 150 m (500 ft) Audio Frequency Response 40 Hz â 18 kHz (+1, -3 dB) Note: Dependent on microphone type RF Tuning Step Size 25 kHz Modulation 45 kHz max. deviation FM, Audio Reference Companding with pre- and de-emphasis Signal-to-Noise Ratio A-weighted, 1% THD, referenced at 0 dB setting on transmitter >113 dB Total Harmonic Distortion 45 kHz max. deviation <0.3%, A-weighted, typical System Audio Polarity Positive pressure on microphone diaphragm (or positive voltage applied to tip of WA302 phone plug) produces positive voltage on pin 2 (with respect to pin 3 of low-impedance output) and the tip of the high impedance 1/4-inch output. Gain Adjustment Range -10 to +40 dB (in 1 dB steps) Battery Type Shure AXT910 (Rechargeable Li-Ion) Battery Life Up to 8 hours (low power mode) Dimensions Storage Temperature Range -29°C (-20°F) to 74°C (165°F) Note: Battery characteristics may limit this range. AF Line of Sight, outdoors for a single 500 m (1600 ft) system Note: Actual range depends on RF signal absorption, reflection and interference. -18°C (0°F) to 63°C (145°F) Note: Battery characteristics may limit this range. 77 mm x 66 mm x 17 mm (3.0 in. x 2.6 in. x 0.7 in.) H x W x D, XXXXERROR: [[ with SB900 battery ]] DOES NOT EXISTXXXX Audio Input Connector 4-Pin male mini connector (TA4M) / 3-Pin male mini connector (LEMO) Configuration Unbalanced Impedance 1 MΊ Maximum Input Level 1 kHz at 1% THD Input Gain Setting RF Output â10 to +9  dB 12.5 dBu +10 to +19 dB â2.5 dBu +20 to +40 dB â7.5 dBu Connector SMA (UHF and ShowLink); Shell=Ground, Center=Signal Antenna Type AXT642 Bodypack Dual Band Antenna (integrated helical and 1/4 wave) Power See Frequency Range and Output Power table Impedance 50 Ί Frequency Bands and Transmitter RF Power 470 to 530 10/100 G1E 470 to 530 10/50 G7C 470 to 510 10/50 G12 479 to 530 10/20 G19 470 to 530 2/10 H4 518 to 578 10/100 H4E 518 to 578 10/50 H12 518 to 565 10/20 H18 518 to 578 2/10 J5 578 to 638 10/100 J5E 578 to 638 10/50 J5HK 578 to 638 10 J12 578 to 638 2/10 K4E 606 to 666 10/50 L3 638 to 698 10/100 L3E 638 to 698 10/50 L20 638 to 698 2/10 M8 666 to 730 10/50 MA24 779 to 806 10 MJBX 806 to 810 10 P8 710 to 790 10/50 P9 710 to 787 10/50 740 to 814 10/50 794 to 806 10/50 R16 Q5 AF G1 16 RF Power (mW) 1. Frequency Range (MHz) 9. Band Input Connector Diagrams LEMO SHIELD   1ÂľF N 5 V DC 100 ÂľF AF . 9. 1. 16 TA4M 440 pF Pad 12 dB Audio Input Ground Bias Voltage Audio Input Ground Certifications Meets essential requirements of the following European Directives: ⢠R&TTE Directive 99/5/EC ⢠WEEE Directive 2002/96/EC, as amended by 2008/34/EC ⢠RoHS Directive 2002/95/EC, as amended by 2008/35/EC Note: Please follow your regional recycling scheme for batteries and electronic waste Meets requirements of the following standards: EN 300 328, EN 300 422 Parts 1 and 2, EN 301 489 Parts 1 and 9, EN60065. Certified under FCC Part 15 and FCC Part 74. Certified in Canada by IC to RSS-123 and RSS-210. Industry Canada ICES-003 Compliance Label: CAN ICES-3 (B)/NMB-3(B) This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. FCC ID: DD4AD1A, DD4AD1B, DD4AD1C, DD4AD1D. IC: 616A-AD1A, 616A-AD1C, 616A-AD1D. 16 This device complies with Industry Canada licence-exempt RSS standard(s). Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prĂŠsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisĂŠe aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioĂŠlectrique subi, mĂŞme si le brouillage est susceptible d'en compromettre le fonctionnement. The CE Declaration of Conformity can be obtained from Shure Incorporated or any of its European representatives. For contact information please visit www.shure. com 9. AF Authorized European representative: Shure Europe GmbH Headquarters Europe, Middle East & Africa Department: EMEA Approval Jakob-Dieffenbacher-Str. 12 75031 Eppingen, Germany Phone: 49-7262-92 49 0 Fax: 49-7262-92 49 11 4 Email: info@shure.de 1. The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance LICENSING INFORMATION Licensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible requirements. Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing of Shure wireless microphone equipment is the userâs responsibility, and licensability depends on the userâs classification and application, and on the selected frequency. Shure strongly urges the user to contact the appropriate telecommunications authority concerning proper licensing, and before choosing and ordering frequencies. Information to the user This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ⢠Reorient or relocate the receiving antenna. ⢠Increase the separation between the equipment and the receiver. ⢠Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. ⢠Consult the dealer or an experienced radio/TV technician for help. Australia Warning for Wireless This device operates under an ACMA class licence and must comply with all the conditions of that licence including operating frequencies. Before 31 December 2014, this device will comply if it is operated in the 520-820 MHz frequency band. WARNING: After 31 December 2014, in order to comply, this device must not be operated in the 694-820 MHz band. AD1 Certified under FCC Part 74. Certified by IC in Canada under RSS-123 and RSS-102. IC: 616A-AD1 G50, 616A-AD1 H50, 616A-AD1 J50, 616A-AD1 L50; 616A-AD1. FCC: DD4AD1G50, DD4AD1H50, DD4AD1J50, DD4AD1L50.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Create Date : 2016:09:01 14:15:30-05:00 Creator : Adobe InDesign CC 2015 (Windows) Modify Date : 2016:09:20 13:36:53-05:00 Has XFA : No Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Metadata Date : 2016:09:20 13:36:53-05:00 Creator Tool : Adobe InDesign CC 2015 (Windows) Instance ID : uuid:41b219d8-5f3a-4f51-bef5-ad312ee61ea7 Original Document ID : xmp.did:B6779F70032DE3118BE4E3ADBE5FD3E2 Document ID : xmp.id:b61f2acf-d597-7442-8b55-5ce1b1452f87 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:b2bb9827-1b9f-3149-a0a9-4d882aa09a82 Derived From Document ID : xmp.did:2f75d881-5500-664f-9e19-8eeceb148c27 Derived From Original Document ID: xmp.did:B6779F70032DE3118BE4E3ADBE5FD3E2 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2015 (Windows) History Changed : / History When : 2016:09:01 14:15:31-05:00 Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Page Count : 12EXIF Metadata provided by EXIF.tools