Shure orporated UR1HB Wireless Microphone User Manual

Shure Incorporated Wireless Microphone

user manual

UR1H Bodypack TransmitterAddendum27A11915 (Rev. 2) Printed in U.S.A.©2008 Shure IncorporatedSpecications:The following specications applyto the UR1H bodypack only.FeaturesHigh RF power (250 mW)• Same audio performance as UR1• Operates with alkaline or lithium batteries• Rapid, two-way infrared (IR) data transmission• External DC power connection• Optional remote mount antenna• Belt clip• Warning: The UR1H belt clip must be installed as shown to ensure compliance with FCC RF exposure guidelines for safe use.Safety InformationThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment is in direct contact with the body of the user under normal operating conditions. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.For body-worn operation, the UR1H has been tested and meets the guidelines for safe use when used properly with the belt clip supplied or designated by Shure for use with this product. For safe use, do not remove or alter the position at the belt clip other than as instructed.Frequency RangeBand RangeH4, H4E 518-578 MHzJ5 578-608, 614-638 MHzJ5E 578-638 MHzL3E, L3 638-698 MHzQ5 740-814 MHzR9 790-862 MHzX1 944-952 MHzRF Carrier Frequency Range518-862 MHz, depending on regionRF Output Power250 mW (24 dBm) across all tunable frequencies,maximum variation of -1.5 dB Power Requirements Two 1.5V AA batteries or 9 - 20 VDC, Shure PS22 adaptor recommended Plug size: 1.7 mm x 4.0 mm (.067 in. x .159 in) NOTE: This equipment has been tested and found to comply with the limits of a Class B digital device when used with PS22, pursuant to Part 15 of the FCC Rules.Current Drain: 350 mA maximum at the battery terminals with 3 VDC applied Battery Life (Typical): 3 hours, with 1.5V AA alkaline batteries7 to 9 hours, with AA lithium primary batteriesOverall DimensionsUR1H: 98 mm L x 60 mm W x 17 mm D(3.84 x 2.38 x 0.66 in.)Net Weight97 g (3.4 oz.) without batteriesUR1H Transmitter RF OutputConnector: SMA Actual Impedance: 50 ΩPin Assignments: Shell = GroundCenter = SignalUR1H Transmitter Audio InputConnector: 4-Pin male mini connector (TA4M)Input Conguration: Unbalanced, activeActual Impedance: >1 MΩMaximum Input Level:(1 kHz, 1% THD)+10 dBu (sensitivity 0 dB) +20 dBu (sensitivity –10 dB)TA4M ConnectorPin Assignments:Pin 1: GroundPin 2: +5 VDC biasPin 3: AudioPin 4: Tied through active load (on main board) to Ground(On instrument adapter cable, Pin 4 oats)REPLACEMENT PARTS AND ACCESSORIESFurnished AccessoriesAntenna, 518-578 MHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UA710Antenna, 578-698 MHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UA720Antenna, 740-865 MHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UA730Threaded Locking Adaptor TA4F ...................... WA340Optional AccessoriesBodypack Pouch (Black) ............................ WA580BBodypack Pouch (White) ............................ WA580WAC to DC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . PS22Antenna AccessoriesNote: SMA to adaptor (UA910) is required to connect the following antenna accessories:Antenna, 944-952 MHz UA740Passive Directional Wideband Antenna(470-1100 MHz)UA860SWB2 ft. Coaxial Antenna Cable, BNC-BNC (RG58C/U) UA8026 ft. Coaxial Antenna Cable, BNC-BNC (RG58C/U) UA80625 ft. Coaxial Antenna Cable, BNC-BNC (RG8X/U) UA82550 ft. Coaxial Antenna Cable, BNC-BNC (RG8X/U) UA850100 ft. Coaxial Antenna Cable, BNC-BNC (RG213/U) UA8100SMA to BNC Adaptor UA910UR1H
CerticationUR1H meets the essential requirements of the European R&TTE Directive 99/5/EC (ETSI EN 300 422 Parts 1 & 2. Note: 250 mW RF output power, EN 300 454 Parts 1 & 2, EN 301 489 Parts 1 & 9) and is eligible to carry the CE marking.Certied under FCC Parts 74 (FCC ID: DD4UR1HA, DD4UR1HB, DD4UR1HC, DD4UR1HF). Certied by IC in Canada under RSS-123 and RSS-102 (IC: 616A-UR1HA, 616A-UR1HB, 616A-UR1HC).The “EU Declaration of Conformity” can be obtained from Shure Inc. or any of its European representatives. For contact information please visit www.shure.comLICENSING INFORMATION:Licensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible requirements. Changes or modications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing of Shure wireless microphone equipment is the user’s responsibility, and licensability depends on the user’s classication and application, and on the selected frequency. Shure strongly urges the user to contact the appropriate telecommunications authority concerning proper licensing, and before choosing and ordering frequencies.Information to UserThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer• This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Note: EMC conformance testing is based on the use of supplied and recommended cable types. The use of other cable types may degrade EMC performanceFCC and IC Radiation Exposure Statement for Mobile Devices (when used with the UA860SWB)This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunc-tion with any other antenna or transmitter.2

Navigation menu