Shure orporated UR1MB Micro Bodypack Transmitter User Manual

Shure Incorporated Micro Bodypack Transmitter

User Manual

UR1M Micro Bodypack TransmitterAddendum27A11964 (Rev. 1) Printed in U.S.A.©2008 Shure IncorporatedSpecications:The following specications apply to the UR1M micro bodypack only.FeaturesSame audio performance as UR1• Rapid two-way infrared (IR) data transmission• User-adjustable RF output level (10 mW or 50 mW)• Operates with two type of primary batteries: alkaline or • lithiumAudio signal is input through a TA4F connector (UR1M) or • a LEMO connector (UR1MLEMO3)Selectable battery metering by battery type• Audio metering on UR1M transmitter that is the same as • UR4 receiverFrequency RangeBand RangeG1 470-530 MHzH4, H4E 518-578 MHzJ5 578-608, 614-638 MHzJ5E 578-638 MHzL3E, L3 638-698 MHzQ5 740-814 MHzQ6 740-752 MHzQ9 740-806 MHzR9 790-865 MHzR16, R18 794-806 MHzA24 779-788, 797-806 MHzJBX 806-810 MHzX1 944-952 MHzRF Carrier Frequency Range470-865, 944-952 MHz depending on regionWorking Range150 m (500 ft.), under typical conditions 500 m (1600 ft.) line-of-sight, outdoors for a single systemNOTE: Actual working range depends on RF signal absorption, reection and interferenceRF Power Output10 mW or 50 mW depending on regionPower Requirements:Two 1.5V AAA alkaline, primary lithium, and NiMH batteriesCurrent Drain: 130 mA max. at 3V (normal RF power setting)200 mA max. at 3V (high RF power setting)Battery Life (Typical): Alkaline 5 hours (normal RF power) 3 hours (high RF power) Lithium primary 9 hours, typicalNiMH 3 hours, typicalSelect Battery Type:Set the the micro bodypack transmitter switch to onPress enter key, then scroll using button to select battery type. Press enter key to conrm.Overall Dimensions49 mm L x 60 mm W x 17 mm D (1.9 x 2.38 x 0.66 in.) Net Weight62 g (2.2 oz.) without batteries WiringTA4F ConnectorMicrophone Element TA4F ConnectorTA4M ConnectorUR1 MIC JACK BOARDNOTE: LAVALIER MIC TIES PINS 3 AND 4 TOGETHER—GUITAR CABLE DOES NOT.Active LoadAudioGroundLEMO ConnectorFVB.00.303 XRB.00.303UR1 LEMO BOARDAudioGroundMicrophone ElementUR1M
UR1M Transmitter RF OutputConnector: SMAActual Impedance: 50 ΩPin Assignments: Shell = GroundCenter = SignalUR1M Transmitter Audio InputConnector: 4-Pin male mini connector (TA4M) 3-Pin female mini connector (LEMO XRB.00.303) Input Conguration: Unbalanced, activeMaximum Input Level:(1 kHz, 1% THD)+5 dBu (sensitivity 0 dB) +15 dBu (sensitivity –10 dB)TA4M Connector Pin Assignments:Pin 1: GroundPin 2: +5 VDC biasPin 3: AudioPin 4: Tied through active load (on main board) to ground.(On instrument adapter cable, Pin 4 oats)LEMO Connector Pin Assignments:Pin 1: Ground Pin 2: +5 VDC biasPin 3: Audio (8.2 kΩ between pin 2 and 3 internal to UR1M)REPLACEMENT PARTS AND ACCESSORIESFurnished AccessoriesAntenna, 470-530 MHz........................................................UA701Antenna, 518-578 MHz........................................................UA711Antenna, 578-638 MHz .......................................................UA721Antenna, 638-698 MHz .......................................................UA722Antenna, 740-865 MHz .......................................................UA731Antenna, 944-952 MHz .......................................................UA741Optional AccessoriesBodypack Pouch (Black) .................................................. WA581BBodypack Pouch (White) ................................................ WA581W3-Pin mini Lemo conversion kit...........................................WA3353-Pin mini Lemo Jack for Lavalier ......................................WA336Assembly Tool for WA336...................................................WA337CerticationUR1M: Type Accepted under FCC Parts 74 (FCC ID: DD4UR1MA, DD4UR1MB, DD4UR1MC, DD4UR1MF, DD4UR1MG). Certied by IC in Canada under RSS-123 and RSS-102 (IC: 616A-UR1MA, 616A-UR1MB, 616A-UR1MC). Meets the essential requirements of the European R&TTE Directive 99/5/EC (ETSI EN 300-422 Parts 1 & 2, EN 301 489 Parts 1 & 9) and is eligible to carry the CE marking.The “EU Declaration of Conformity” can be obtained from Shure Inc. or any of its European representatives. For contact information please visit www.shure.comLICENSING INFORMATION:Licensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible requirements.Changes or modications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing of Shure wireless microphone equipment is the user’s responsibility, and licensability depends on the user’s classication and applica-tion, and on the selected frequency. Shure strongly urges the user to contact the appropriate telecommunications authority concerning proper licensing, and before choosing and ordering frequencies.Information to UserThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealerThis Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Note: EMC conformance testing is based on the use of supplied and recommended cable types. The use of other cable types may degrade EMC performance.

Navigation menu