Sichuan Changhong Electronic Component M06USA1 WLAN 802.11/b/g/n module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3240249
Application ID	cMQvaLCoJ8nu61xLAKBF1Q==
Document Description	15_WIFI-2-M06USA1 UserMan,r1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	137.28kB (1715994 bits)
Date Submitted	2016-12-27 00:00:00
Date Available	2016-12-27 00:00:00
Creation Date	2016-10-20 11:04:01
Producing Software	Microsoft® Word 2010
Document Lastmod	2016-11-07 18:23:02
Document Title	Users Manual
Document Creator	Microsoft® Word 2010
Document Author:	bailang

WIFI-2-M06USA1
WLAN 802.11b/g/n module
特性 Features：
 接收制式 Reserving System
IEEE Std. 802.11b
IEEE Std. 802.11g
IEEE Std. 802.11n
 芯片方案 Chip Solution
MT7601UN
 波段 Band
2.4G
四川长虹电子部品有限公司
Sichuan Changhong Electronic Component Co., Ltd.
地址 Add : 四川省绵阳市安县花荄镇罗胜街
Luosheng street,Huagai Zhen, Anxian, Mianyang, Sichuan, China
传真 Fax : +86-0816-2410643
网
址: http://www.changhong.com
WIFI-2-M06USA1
WLAN 802.11b/g/n module
1. Introduction
WIFI-2-M06U is based on MTK MT7601,complied with IEEE 802.11b/g/n standard from
2.4-2.5GHz.This documentation describes the engineering requirements specification.
1.1 RF module Overview
The general HW architecture for the module is shown in Figure 1. This WLAN Module design is based
on MTK MT7601. It is a highly integrated single-chip MIMO(Multiple In Multiple Out) Wireless LAN
(WLAN) USB2.0 network interface controllercomplying with the 802.11n specification. It combines a
MAC, a 1T1R capable baseband,and RF in a single chip. The MT7601 provides a complete solution for
a highthroughput performance wireless client.
Figure 1 WIFI-2-M06U Block Diagram
1.2 Specification reference
This specification is based on additional references listed below.
_ IEEE Std. 802.11b
_ IEEE Std. 802.11g
_ IEEE Std. 802.11n
1.3 System Functions
Table1: General Specification as below:
Main Chipset
Operating Frequency
WiFi Standard
Modulation
Operation Temperature
MTK MT7601UN
2.412~2.472GHz
802.11b/g/n(1x1)
11b: DBPSK, DQPSK and CCK and DSSS 11g: BPSK, QPSK,
16QAM, 64QAM and OFDM 11n: MCS0~15 OFDM
11b:1, 2, 5.5 and 11Mbps 11g:6, 9, 12, 18, 24, 36, 48 and 54
Mbps 11n: MCS0~15, up to 150Mbps
6pin
USB 2.0
4-layers design
Typical，
12.3mm(W)*12.7mm(L)*1.95mm(H)
0℃ to +60℃
Storage Temperature
Operation Voltage
-15℃ to +45℃
3.3V +/-10% （Ripple: ≤30mVp-p）
Data rates
Form factor
Host Interface
PCB Stack
Dimension
Ratings
3.3V
四川长虹电子部品有限公司
Sichuan Changhong Electronic Component Co., LTD
500mA
page 2 of 4
WIFI-2-M06USA1
WLAN 802.11b/g/n module
2. Mechanical Specification
Typical Dimension (W x L x T): 12.3mmx 12.7mm x 1.95mm (tolerance : +/-0.15 mm)
PCB Thickness: 1.0mm
Pin
TYPE
power3.3v
UDN
UDP
GND
GND
ANT
四川长虹电子部品有限公司
Sichuan Changhong Electronic Component Co., LTD
page 3 of 4
WIFI-2-M06USA1
WLAN 802.11b/g/n module
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: 1) this device may not cause harmful interference, and 2)
this device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement
This modular complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Attention: Limited Modular Approval - this RF Module may not be sold to the generic public and
requires professional installation. Due to the fact that this RF Module is not equipped with an
own shielding, the end-product incl. this RF Module has to show compliance to the FCC rules
(15C / radiated emissions).
(OEM) Integrator has to assure compliance of the entire end-product incl. the integrated RF
Module. Additional measurements (15C) and/or equipment authorizations
(e.g either a complete new certification or a Class II Permissive Change) may need to be
addressed depending on co-location or simultaneous transmission issues if applicable.
Integrator is reminded to assure that these installation instructions will not be made available to
the end-user of the final host device.
The Integrator will be responsible to satisfy SAR/ RF Exposure requirements, when the module
integrated into any (portable, mobile, fixed) host device.
The final host device, into which this RF Module is integrated" has to be labeled with an auxiliary
label stating the FCC ID of the RF Module, such as "Contains FCC ID: 2AC49-M06USA1".
四川长虹电子部品有限公司
Sichuan Changhong Electronic Component Co., LTD
page 4 of 4

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : bailang
Create Date                     : 2016:10:20 11:04:01+08:00
Modify Date                     : 2016:11:07 18:23:02+08:00
Has XFA                         : No
Language                        : zh-CN
Tagged PDF                      : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Creator                         : bailang
Title                           : 技术规格书模板文件
Creator Tool                    : Microsoft® Word 2010
Metadata Date                   : 2016:11:07 18:23:02+08:00
Producer                        : Microsoft® Word 2010
Document ID                     : uuid:c9c7f3a3-5d16-4aaa-b42b-ea1d0aee6aa1
Instance ID                     : uuid:67bf51a5-7db8-4429-870c-9027cfdb845d
Page Count                      : 4

EXIF Metadata provided by EXIF.tools