Siemens RF350R02 RFID Reader 13.56 MHz User Manual SIMATIC RF300

Siemens AG RFID Reader 13.56 MHz SIMATIC RF300

UserManual.wiki >

RF350R02 User Manual >

Contents

Users manual 2

Readers SIMATIC RF300 114 System Manual, 07/2016, C79000-G8976-C345-0x ISO 14443 functionality With all readers of the second generation of the RF300 family, you can use ISO 14443 transponders. The RF300 readers of the second generation therefore replace the MOBY E readers SLG 72 and SLG 75. Note that the readers for RF300, ISO 15963 or ISO 14443 operation must have parameters assigned. The parameter assignment done with the aid of the RESET frame (INIT-Run). The following commands are supported in ISO 14443 operation of the readers: ● READ ● WRITE ● MDS-STATUS (mode 3) ● INIT ● REPEAT Special ISO 14443 commands such as "INCREMENT", "DECREMENT" or "SET-VALUE" are not supported.

Readers 5.1 SIMATIC RF310R SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 115 5.1 SIMATIC RF310R 5.1.1 Features SIMATIC RF310R Characteristics Design ① RS-422 interface ② Status display Area of application Identification tasks on small assembly lines in harsh industrial environments 5.1.2 RF310R ordering data Table 5- 1 RF310R ordering data Article number RF310R with RS-422 interface (3964R) horizontal base plate 6GT2801-1AB10 RF310R with RS-422 interface (3964R) base plate turned through 90° 6GT2801-1AB10-0AX1

Readers 5.1 SIMATIC RF310R SIMATIC RF300 116 System Manual, 07/2016, C79000-G8976-C345-0x 5.1.3 Pin assignment RF310R with RS-422 interface Pin Pin Device end 8-pin M12 Assignment 1 + 24 V 2 - Transmit 3 0 V 4 + Transmit 5 + Receive 6 - Receive 7 Unassigned 8 Earth (shield) 5.1.4 LED operating display The operational statuses of the reader are displayed by the LEDs. The LED can adopt the colors green, red or yellow and the statuses off , on , flashing : Table 5- 2 LED operating display on the reader Color Meaning Operating voltage present, reader not initialized or antenna switched off Operating voltage present, reader initialized and antenna switched on 1) Transponder present Error has occurred, the type of flashing corresponds to the error code in the table in the section Error codes. The optical error display is only reset if the corresponding reset parameter ("option_1", see FC 45 / FB 45 documentation, section Input parameters) is set. 1) Only in the "with presence" mode. 5.1.5 Ensuring reliable data exchange The "center point" of the transponder must be situated within the transmission window.

Readers 5.1 SIMATIC RF310R SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 117 5.1.6 Metal-free area The RF310R can be flush-mounted in metal. Please allow for a possible reduction in the field data values. Figure 5-1 Metal-free area for RF310R To avoid any impact on the field data, the distance a should be ≥ 20 mm. 5.1.7 Minimum distance between RF310R readers RF310R side by side D ≥ 150 mm (with 2 readers) D ≥ 200 mm (with more than 2 readers) Figure 5-2 Minimum distance between RF310R readers

Readers 5.1 SIMATIC RF310R SIMATIC RF300 118 System Manual, 07/2016, C79000-G8976-C345-0x RF310R face-of-face D ≥ 300 mm Figure 5-3 Face-of-face distance between two RF310Rs 5.1.8 Technical specifications Table 5- 3 Technical specifications of the RF310R reader with RS-422 interface 6GT2801-1AB10 Product type designation SIMATIC RF310R Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 60 mm Maximum data transmission speed reader ↔ transponder RF300 transponder ISO transponder • Read • approx. 8000 bytes/s • approx. 1500 bytes/s • Write • approx. 8000 bytes/s • approx. 1500 bytes/s Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader See section "Field data for transponders, readers and antennas (Page 48)." MTBF (Mean Time Between Failures) 170 years Interfaces Electrical connector design M12, 8-pin Standard for interfaces for communication RS-422 Antenna integrated

Readers 5.1 SIMATIC RF310R SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 119 6GT2801-1AB10 Mechanical specifications Housing • Material • Plastic PA 12 • Color • Anthracite Recommended distance to metal 0 mm Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 50 mA Permitted ambient conditions Ambient temperature • During operation • -25 to +70 ℃ • During transportation and storage • -40 to +85 ℃ Degree of protection to EN 60529 IP67 Shock-resistant to EN 60721-3-7, Class 7 M3 50 g Vibration-resistant to EN 60721-3-7, Class 7 M3 20 g Torsion and bending load Not permitted Design, dimensions and weight Dimensions (L x W x H) 75 x 55 x 30 mm Weight 200 g Type of mounting 4 x M5 screw; 1.5 Nm Cable length for RS-422 interface, maximum 1000 m LED display design 3-color LED Standards, specifications, approvals Proof of suitability Radio to R&TTE directives EN 300330, EN 301489, CE, FCC, UL/CSA

Readers 5.1 SIMATIC RF310R SIMATIC RF300 120 System Manual, 07/2016, C79000-G8976-C345-0x 5.1.9 Approvals FCC information Siemens SIMATIC RF310R (MLFB 6GT2801-1AB10); FCC ID NXW-RF310R This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement.

Readers 5.1 SIMATIC RF310R SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 121 5.1.10 Dimension drawing Figure 5-4 Dimension drawing for RF310R Dimensions in mm

Readers 5.2 SIMATIC RF310R with Scanmode SIMATIC RF300 122 System Manual, 07/2016, C79000-G8976-C345-0x 5.2 SIMATIC RF310R with Scanmode You will find detailed information on the SIMATIC RF310R with Scanmode on the Internet (https://support.industry.siemens.com/cs/ww/en/ps/15034). 5.2.1 Features SIMATIC RF310R special version Scanmode Characteristics Design ① RS-422 interface ② Status display Area of application Identification tasks on small assembly lines in harsh industrial environments 5.2.2 Ordering data for RF310R with Scanmode Table 5- 4 Ordering data RF310R Scanmode Article number RF310R special version Scanmode with RS-422 interface 6GT2801-1AB20-0AX1

Readers 5.2 SIMATIC RF310R with Scanmode SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 123 5.2.3 Pin assignment RF310R special version Scanmode RS-422 interface Pin Pin Device end 8-pin M12 Assignment 1 + 24 V 2 - Transmit 3 0 V 4 + Transmit 5 + Receive 6 - Receive 7 Unassigned 8 Earth (shield) 5.2.4 LED operating display The operational statuses of the reader are displayed by the LEDs. The LED can adopt the colors green, red or yellow and the statuses off , on , flashing : Table 5- 5 LED operating display on the reader Color Meaning Operating voltage present, reader ready for operation Transponder present Red LED for error display is activated permanently if correct operation of the reader cannot be guaranteed (e. g. faulty start, checksum error during operation). 5.2.5 Ensuring reliable data exchange The "center point" of the transponder must be situated within the transmission window.

Readers 5.2 SIMATIC RF310R with Scanmode SIMATIC RF300 124 System Manual, 07/2016, C79000-G8976-C345-0x 5.2.6 Metal-free area The RF310R special version can be flush-mounted in metal. Please allow for a possible reduction in the field data values. Figure 5-5 Metal-free area for RF310R special version To avoid any impact on the field data, the distance a should be ≥ 20 mm. 5.2.7 Minimum distance between several readers RF310R special version side by side D ≥ 150 mm (with 2 readers) D ≥ 200 mm (with more than 2 readers) Figure 5-6 Minimum distance between RF310R readers

Readers 5.2 SIMATIC RF310R with Scanmode SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 125 RF310R special version face-to-face D ≥ 300 mm Figure 5-7 Face-to-face distance between two RF310R special version 5.2.8 Technical specifications Table 5- 6 Technical specifications of the RF310R reader with Scanmode 6GT2801-1AB20-0AX1 Product type designation SIMATIC RF310R Scanmode Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 60 mm Maximum data transmission speed reader ↔ transponder RF300 transponder ISO transponder • Read • approx. 8000 bytes/s • approx. 1500 bytes/s Transmission speed 9.6, 19.2, 38.4, 57.6, 115.2 kBd Read/write distances of the reader See section "Field data for transponders, readers and antennas (Page 48)." MTBF (Mean Time Between Failures) 170 years Interfaces Electrical connector design M12, 8-pin Standard for interfaces for communication RS-422 (Scanmode) Antenna integrated Mechanical specifications Housing • Material • Plastic PA 12 • Color • Anthracite Recommended distance to metal 0 mm

Readers 5.2 SIMATIC RF310R with Scanmode SIMATIC RF300 126 System Manual, 07/2016, C79000-G8976-C345-0x 6GT2801-1AB20-0AX1 Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 50 mA Permitted ambient conditions Ambient temperature • During operation • -25 to +70 ℃ • During transportation and storage • -40 to +85 ℃ Degree of protection to EN 60529 IP67 Shock-resistant to EN 60721-3-7, Class 7 M3 50 g Vibration-resistant to EN 60721-3-7, Class 7 M3 20 g Torsion and bending load Not permitted Design, dimensions and weight Dimensions (L x W x H) 75 x 55 x 30 mm Weight 170 g Type of mounting 4 x M5 screws; 1.5 Nm Cable length for RS-422 interface, maximum 1000 m LED display design 3-color LED Standards, specifications, approvals Proof of suitability Radio to R&TTE directives EN 300330, EN 301489, CE, FCC, UL/CSA

Readers 5.2 SIMATIC RF310R with Scanmode SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 127 5.2.9 Approvals FCC information Siemens SIMATIC RF310R (MLFB 6GT2801-1AB20-0AX1); FCC ID NXW-RF310R This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement.

Readers 5.2 SIMATIC RF310R with Scanmode SIMATIC RF300 128 System Manual, 07/2016, C79000-G8976-C345-0x 5.2.10 Dimension drawing Figure 5-8 Dimension drawing RF310R special version Scanmode Dimensions in mm

Readers 5.3 SIMATIC RF310R - second generation SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 129 5.3 SIMATIC RF310R - second generation 5.3.1 Features SIMATIC RF310R Characteristics Design ① RS-422 interface ② LED operating display Area of application Identification tasks on small assembly lines in harsh industrial environments 5.3.2 Ordering data Table 5- 7 RF310R ordering data Article number RF310R with RS-422 interface (3964R) 6GT2801-1BA10

Readers 5.3 SIMATIC RF310R - second generation SIMATIC RF300 130 System Manual, 07/2016, C79000-G8976-C345-0x 5.3.3 Pin assignment of the RS-422 interface Table 5- 8 Pin assignment Pin Pin Device end 8-pin M12 Assignment 1 + 24 V 2 - Transmit 3 0 V 4 + Transmit 5 + Receive 6 - Receive 7 Unassigned 8 Earth (shield) 5.3.4 LED operating display The operational statuses of the reader are displayed by two LEDs. The LEDs can adopt the colors white green, red, yellow or blue and the statuses off , on , flashing : Table 5- 9 Display elements LED Meaning The reader is turned off. The reader is turned on and is searching for transponders. The reader is in the "Setup" mode, in the "Search for transponders" status and has not yet received a "RESET" command and is not ready. / There is transponder in the antenna field. The reader is in the "Setup" mode, in the status "Show quality", has not yet re-ceived a "RESET" command and is not ready. Depending on the signal strength, the LED flashes or is lit permanently. The reader has received a "RESET" command. There is transponder in the antenna field. The reader is ready. There is an error. The number of flashes provides information about the current error. You will find more information on error messages in the section "System diag-nostics (Page 395)". 5.3.5 Ensuring reliable data exchange The "center point" of the transponder must be situated within the transmission window.

Readers 5.3 SIMATIC RF310R - second generation SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 131 5.3.6 Metal-free area The RF310R can be flush-mounted in metal. Allow for a possible reduction in the field data. To avoid any influence on the field data, the distance "a" should be kept to. a ≥ 20 mm Figure 5-9 Metal-free area for RF310R 5.3.7 Minimum distance between RF310R readers RF310R side by side D ≥ 150 mm (with 2 readers) D ≥ 200 mm (with more than 2 readers) Figure 5-10 Minimum distance between RF310R readers

Readers 5.3 SIMATIC RF310R - second generation SIMATIC RF300 132 System Manual, 07/2016, C79000-G8976-C345-0x RF310R face-of-face D ≥ 300 mm Figure 5-11 Face-of-face distance between two RF310Rs 5.3.8 Technical specifications Table 5- 10 Technical specifications of the RF310R reader with RS-422 interface 6GT2801-1BA10 Product type designation SIMATIC RF310R Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 60 mm Maximum data transmission speed reader ↔ transponder RF300 transponder ISO transponder (MDS D) ISO tran-sponder (MDS E) • Read • ≤ 8000 bytes/s • ≤ 3300 bytes/s • ≤ 3400 bytes/s • Write • ≤ 8000 bytes/s • ≤ 1700 bytes/s • ≤ 800 bytes/s Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader See section "Field data for transponders, readers and antennas (Page 48)." MTBF (Mean Time Between Failures) 273 years Interfaces Electrical connector design M12, 8-pin Standard for interfaces for communication RS-422 Antenna integrated

Readers 5.3 SIMATIC RF310R - second generation SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 133 6GT2801-1BA10 Mechanical specifications Housing • Material • Plastic PA 12 • Color • TI-Grey Recommended distance to metal 0 mm Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 55 mA Permitted ambient conditions Ambient temperature • During operation • -25 to +70 ℃ • During transportation and storage • -40 to +85 ℃ Degree of protection to EN 60529 IP67 Shock-resistant to EN 60721-3-7, Class 7 M3 50 g Vibration-resistant to EN 60721-3-7, Class 7 M3 20 g Torsion and bending load Not permitted Design, dimensions and weight Dimensions (L x W x H) 75 x 55 x 30 mm Weight 100 g Type of mounting 4 x M5 screws; 1.5 Nm Cable length for RS-422 interface, maximum 1000 m LED display design 2 LEDs, 5 colors Standards, specifications, approvals Proof of suitability Radio to R&TTE directives EN 300330, EN 301489, CE, FCC, UL/CSA (IEC61010 / IEC61010-2-201), Ex approval

Readers 5.3 SIMATIC RF310R - second generation SIMATIC RF300 134 System Manual, 07/2016, C79000-G8976-C345-0x 5.3.9 Approvals FCC information Siemens SIMATIC RF310R (MLFB 6GT2801-1BA10); FCC ID NXW-RF310R02 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement.

Readers 5.3 SIMATIC RF310R - second generation SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 135 UL information (IEC61010-1 / IEC61010-2-201) This standard applies to equipment designed to be safe at least under the following conditions: ● a) indoor use; ● b) altitude up to 2 000 m; ● c) temperature -25 °C to 70 °C; ● d) maximum relative humidity 80 % for temperature up to 31 °C decreasing linearly to 50 % relative humidity at 40 °C; ● e) TRANSIENT OVERVALTAGES up to the levels of OVERVALTAGE CATEGORY II, NOTE 1: These levels of transient overvoltage are typical for equipment supplied from the building wiring. ● f) using a "NEC Class 2" power supply is required 5.3.10 Dimension drawing Figure 5-12 Dimension drawing for RF310R Dimensions in mm

Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 136 System Manual, 07/2016, C79000-G8976-C345-0x 5.4 SIMATIC RF340R/RF350R 5.4.1 SIMATIC RF340R 5.4.1.1 Features SIMATIC RF340R Characteristics Design ① RS-422 interface ② Status display Area of application Identification tasks on assembly lines in harsh industrial environments 5.4.1.2 Ordering data for RF340R Table 5- 11 Ordering data for RF340R Article number RF340R with RS-422 interface (3964R) 6GT2801-2AB10

Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 137 5.4.1.3 Pin assignment of RF340R RS422 interface Pin Pin Device end 8-pin M12 Assignment 1 + 24 V 2 - Transmit 3 0 V 4 + Transmit 5 + Receive 6 - Receive 7 Unassigned 8 Earth (shield) 5.4.1.4 LED operating display The operational statuses of the reader are displayed by the LEDs. The LED can adopt the colors green, red or yellow and the statuses off , on , flashing : Table 5- 12 LED operating display on the reader Color Meaning Operating voltage present, reader not initialized or antenna switched off Operating voltage present, reader initialized and antenna switched on 1) Transponder present Error has occurred, the type of flashing corresponds to the error code in the table in the section Error codes. The optical error display is only reset if the corresponding reset parameter ("option_1", see FC 45 / FB 45 documentation, section Input parameters) is set. 1) Only in the "with presence" mode. 5.4.1.5 Ensuring reliable data exchange The "center point" of the transponder must be situated within the transmission window.

Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 138 System Manual, 07/2016, C79000-G8976-C345-0x 5.4.1.6 Metal-free area The RF340R can be flush-mounted in metal. Please allow for a possible reduction in the field data values. Figure 5-13 Metal-free area for RF340R To avoid any impact on the field data, the distance a should be ≥ 20 mm. 5.4.1.7 Minimum distance between RF340R readers RF340R side by side D ≥ 200 mm (with 2 readers) D ≥ 250 mm (with more than 2 readers) Figure 5-14 Minimum distance between RF340R readers

Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 139 RF340R face-of-face D ≥ 500 mm Figure 5-15 Face-of-face distance between two RF340Rs 5.4.1.8 Technical specifications Table 5- 13 Technical specifications of the RF340R reader 6GT2801-2AB10 Product type designation SIMATIC RF340R Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 140 mm Maximum data transmission speed reader ↔ transponder RF300 transponder ISO transponder • Read • approx. 8000 bytes/s • approx. 1500 bytes/s • Write • approx. 8000 bytes/s • approx. 1500 bytes/s Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader See section "Field data for transponders, readers and antennas (Page 48)." MTBF (Mean Time Between Failures) 140 years Interfaces Electrical connector design M12, 8-pin Standard for interfaces for communication RS-422 (3964R protocol) Antenna integrated

Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 140 System Manual, 07/2016, C79000-G8976-C345-0x 6GT2801-2AB10 Mechanical specifications Housing • Material • Plastic PA 12 • Color • Anthracite Recommended distance to metal 0 mm Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 100 mA Permitted ambient conditions Ambient temperature • During operation • -25 to +70 ℃ • During transportation and storage • -40 to +85 ℃ Degree of protection to EN 60529 IP67 Shock-resistant to EN 60721-3-7, Class 7 M3 50 g Vibration-resistant to EN 60721-3-7, Class 7 M3 20 g Torsion and bending load Not permitted Design, dimensions and weight Dimensions (L x W x H) 75 x 75 x 41 mm Weight 250 g Type of mounting 2 x M5 screws; 1.5 Nm Cable length for RS-422 interface, maximum 1000 m LED display design 3-color LED Standards, specifications, approvals Proof of suitability Radio to R&TTE directives EN 300330, EN 301489, CE, FCC, UL/CSA, Ex approval

Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 141 5.4.1.9 Approvals FCC information Siemens SIMATIC RF340R (MLFB 6GT2801-2AA10); FCC ID NXW-RF340R Siemens SIMATIC RF340R (MLFB 6GT2801-2AB10); FCC ID NXW-RF340R01 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement.

Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 142 System Manual, 07/2016, C79000-G8976-C345-0x 5.4.1.10 Dimension drawing Figure 5-16 Dimension drawing for RF340R Dimensions in mm

Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 143 5.4.2 SIMATIC RF350R 5.4.2.1 Features SIMATIC RF350R Characteristics Design ① Antenna connection ② RS-422 interface ③ Status display Area of application Identification tasks in assembly lines in harsh industrial environments; for external antennas (ANT 1, ANT 3, ANT 12, ANT 18, ANT 30) Note Reader requires external antennas Note that the RF350R reader is designed only for operation with external antennas and only works in conjunction with the antennas ANT 1, ANT 3, ANT 12, ANT 18 or ANT 30. 5.4.2.2 Ordering data for RF350R Table 5- 14 Ordering data for RF350R Article number RF350R with RS-422 interface (3964R) 6GT2801-4AB10

Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 144 System Manual, 07/2016, C79000-G8976-C345-0x 5.4.2.3 Pin assignment of RF350R RS422 interface Pin Pin Device end 8-pin M12 Assignment 1 + 24 V 2 - Transmit 3 0 V 4 + Transmit 5 + Receive 6 - Receive 7 Unassigned 8 Earth (shield) 5.4.2.4 LED operating display The operational statuses of the reader are displayed by the LEDs. The LED can adopt the colors green, red or yellow and the statuses off , on , flashing : Table 5- 15 LED operating display on the reader Color Meaning Operating voltage present, reader not initialized or antenna switched off Operating voltage present, reader initialized and antenna switched on 1) Transponder present Error has occurred, the type of flashing corresponds to the error code in the table in the section Error codes. The optical error display is only reset if the corresponding reset parameter ("option_1", see FC 45 / FB 45 documentation, section Input parameters) is set. 1) Only in the "with presence" mode. 5.4.2.5 Ensuring reliable data exchange The "center point" of the transponder must be situated within the transmission window. 5.4.2.6 Metal-free area The RF350R reader does not have an internal antenna. Operation is not affected by mounting on metal or flush-mounting in metal. For information about the metal-free area required by the external antennas, refer to the corresponding section of the chapter Auto-Hotspot.

Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 145 5.4.2.7 Technical specifications Table 5- 16 Technical specifications of the RF350R reader 6GT2801-4AB10 Product type designation SIMATIC RF350R Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range • ANT 1 • 140 mm • ANT 3 • 50 mm • ANT 12 • 16 mm • ANT 18 • 35 mm • ANT 30 • 55 mm Maximum data transmission speed reader ↔ transponder RF300 transponder ISO transponder • Read • approx. 8000 bytes/s • approx. 1500 bytes/s • Write • approx. 8000 bytes/s • approx. 1500 bytes/s Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader See section "Field data for transponders, readers and antennas (Page 48)." MTBF (Mean Time Between Failures) 140 years Interfaces Electrical connector design M12, 8-pin Antenna connector design M8, 4-pin Standard for interfaces for communication RS-422 (3964R protocol) Antenna External, antennas ANT 1, ANT 3, ANT 12, ANT 18 or ANT 30 Mechanical specifications Housing • Material • Plastic PA 12 • Color • Anthracite Recommended distance to metal 0 mm

Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 146 System Manual, 07/2016, C79000-G8976-C345-0x 6GT2801-4AB10 Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 100 mA Permitted ambient conditions Ambient temperature • During operation • -25 to +70 ℃ • During transportation and storage • -40 to +85 ℃ Degree of protection to EN 60529 IP65 Shock-resistant to EN 60721-3-7, Class 7 M3 50 g Vibration-resistant to EN 60721-3-7, Class 7 M3 20 g Torsion and bending load Not permitted Design, dimensions and weight Dimensions (L x W x H) 75 x 75 x 41 mm Weight 250 g Type of mounting 2 x M5 screws; 1.5 Nm Cable length for RS-422 interface, maximum 1000 m LED display design 3-color LED Standards, specifications, approvals Proof of suitability Radio to R&TTE directives EN 300330, EN 301489, CE, FCC, UL/CSA, Ex approval

Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 147 5.4.2.8 Approvals FCC information Siemens SIMATIC RF350R (MLFB 6GT2801-4AA10); FCC ID NXW-RF350R Siemens SIMATIC RF350R (MLFB 6GT2801-4AB10); FCC ID NXW-RF350R01 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement.

Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 148 System Manual, 07/2016, C79000-G8976-C345-0x 5.4.2.9 Dimension drawing Figure 5-17 RF350R dimension drawing Dimensions in mm

Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 149 5.4.3 Use of the reader in hazardous areas TÜV NORD CERT GmbH as accredited test center and certification body, no. 0044 as per Article 9 of the Directive 94/9/EC of the European Council of 23 March 1994, has confirmed the compliance with the essential health and safety requirements relating to the design and construction of equipment and protective systems intended for use in hazardous areas as per Annex II of the Directive. The essential health and safety requirements are satisfied in accordance with the following standards: Document Title EN 60079-0: 2006 Electrical equipment for hazardous gas atmospheres - Part 0: General requirements EN 60079-15: 2005 Electrical equipment for hazardous gas atmospheres - Part 15: Design, testing and identification of electrical equipment with type of protection "n" IEC 61241 -0: 2006 Electrical apparatus for use in the presence of combustible dust - Part 0: General requirements IEC 61241 -1: 2004 Electrical apparatus for use in the presence of combustible dust - Part 1: Protection through enclosure WARNING EXPLOSION HAZARD DO NOT CONNECT OR DISCONNECT EQUIPMENT WHEN A FLAMMABLE OR COMBUSTIBLE ATMOSPHERE IS PRESENT. Identification The identification of the electrical equipment as an enclosed unit is: II 3 G Ex nA nC IIB T5 II 3 D Ex tD A22 IP6x T80 °C -25 °C to +70 °C Un = 20 to 30 VDC The equipment also has the following additional markings: XXXYYYZZZ [= serial number, is assigned during production] TÜV 10 ATEX 556039 [= certificate number]

Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 150 System Manual, 07/2016, C79000-G8976-C345-0x 5.4.3.1 Use of the readers in hazardous areas for gases Temperature class delineation for gases The temperature class of the reader for hazardous areas depends on the ambient temperature range: Ambient temperature range Temperature class -25 °C to +70 °C T5 WARNING Ignitions of gas-air mixtures When using the RF340R/RF350R readers, check to ensure that the temperature class is observed in respect of the requirements of the area of application. Non-compliance with the permitted temperature ranges while using the reader can lead to ignitions of gas-air mixtures. 5.4.3.2 Use of the readers in hazardous areas for dusts The equipment is suitable for dusts whose ignition temperatures for a dust layer of 5 mm are higher than 80 °C (smoldering temperature). With the ignition temperature according to type of protection iD specified here in compliance with IEC 61241-0 and IEC 61241-11, the smoldering temperature of the dust layer is referenced in this case. Temperature class delineation for dusts Ambient temperature range Temperature value -25 °C < Ta < +70 °C T80 °C WARNING Ignitions of dust-air mixtures When using the RF340R/RF350R readers, check to ensure that the temperature values are observed in respect of the requirements of the area of application. Non-compliance with the permitted temperature ranges while using the reader can lead to ignitions of dust-air mixtures.

Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 151 5.4.3.3 Installation and operating conditions for the hazardous area NOTICE Device may be damaged Note the following conditions when installing and operating the device in a hazardous zone to avoid damage: • Making and breaking of circuits is permitted only in a de-energized state. • The maximum surface temperature, corresponding to the marking, applies only for operation without a cover of dust. • The device may only be operated in such a way that adequate protection against UV light is ensured. • The device may not be operated in areas influenced by processes that generate high electrostatic charges. • The equipment must be installed so that it is mechanically protected. • The device sockets must be protected with a shrink-on tube. • The 8 pin connector must be grounded via its supply line. • The device may only be operated with accessories specified or supplied by the manufacturer. All the points above also apply to the accessories (cables and connectors) and to the antennas (exception: the housing of antenna 1 does not need to be installed with impact protection).

Readers 5.5 SIMATIC RF340R/RF350R - second generation SIMATIC RF300 152 System Manual, 07/2016, C79000-G8976-C345-0x 5.5 SIMATIC RF340R/RF350R - second generation 5.5.1 SIMATIC RF340R - second generation 5.5.1.1 Features SIMATIC RF340R Characteristics Design ① RS-422 interface ② LED operating display Area of application Identification tasks on assembly lines in harsh industrial environments 5.5.1.2 Ordering data Table 5- 17 Ordering data for RF340R Article number RF340R with RS-422 interface (3964R) 6GT2801-2BA10

Readers 5.5 SIMATIC RF340R/RF350R - second generation SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 153 5.5.1.3 Pin assignment of the RS-422 interface Table 5- 18 Pin assignment Pin Pin Device end 8-pin M12 Assignment 1 + 24 V 2 - Transmit 3 0 V 4 + Transmit 5 + Receive 6 - Receive 7 Unassigned 8 Earth (shield) 5.5.1.4 LED operating display The operational statuses of the reader are displayed by two LEDs. The LEDs can adopt the colors white green, red, yellow or blue and the statuses off , on , flashing : Table 5- 19 Display elements LED Meaning The reader is turned off. The reader is turned on and is searching for transponders. The reader is in the "Setup" mode, in the "Search for transponders" status and has not yet received a "RESET" command and is not ready. / There is transponder in the antenna field. The reader is in the "Setup" mode, in the status "Show quality", has not yet re-ceived a "RESET" command and is not ready. Depending on the signal strength, the LED flashes or is lit permanently. The reader has received a "RESET" command. There is transponder in the antenna field. The reader is ready. There is an error. The number of flashes provides information about the current error. You will find more information on error messages in the section "System diag-nostics (Page 395)". 5.5.1.5 Ensuring reliable data exchange The "center point" of the transponder must be situated within the transmission window.

Readers 5.5 SIMATIC RF340R/RF350R - second generation SIMATIC RF300 154 System Manual, 07/2016, C79000-G8976-C345-0x 5.5.1.6 Metal-free area The RF340R can be flush-mounted in metal. Allow for a possible reduction in the field data. To avoid any influence on the field data, the distance "a" should be kept to. a ≥ 20 mm Figure 5-18 Metal-free area for RF340R 5.5.1.7 Minimum distance between RF340R readers RF340R side by side D ≥ 200 mm (with 2 readers) D ≥ 250 mm (with more than 2 readers) Figure 5-19 Minimum distance between RF340R readers

Readers 5.5 SIMATIC RF340R/RF350R - second generation SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 155 RF340R face-of-face D ≥ 500 mm Figure 5-20 Face-of-face distance between two RF340Rs 5.5.1.8 Technical specifications Table 5- 20 Technical specifications of the RF340R reader 6GT2801-2BA10 Product type designation SIMATIC RF340R Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 140 mm Maximum data transmission speed reader ↔ transponder RF300 transponder ISO transponder (MDS D) ISO tran-sponder (MDS E) • Read • ≤ 8000 bytes/s • ≤ 3300 bytes/s • ≤ 3400 bytes/s • Write • ≤ 8000 bytes/s • ≤ 1700 bytes/s • ≤ 800 bytes/s Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader See section "Field data for transponders, readers and antennas (Page 48)." MTBF (Mean Time Between Failures) 260 years Interfaces Electrical connector design M12, 8-pin Standard for interfaces for communication RS-422 (3964R protocol) Antenna integrated

Readers 5.5 SIMATIC RF340R/RF350R - second generation SIMATIC RF300 156 System Manual, 07/2016, C79000-G8976-C345-0x 6GT2801-2BA10 Mechanical specifications Housing • Material • Plastic PA 12 • Color • TI-Grey Recommended distance to metal 0 mm Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 55 mA Permitted ambient conditions Ambient temperature • During operation • -25 to +70 ℃ • During transportation and storage • -40 to +85 ℃ Degree of protection to EN 60529 IP67 Shock-resistant to EN 60721-3-7, Class 7 M3 50 g Vibration-resistant to EN 60721-3-7, Class 7 M3 20 g Torsion and bending load Not permitted Design, dimensions and weight Dimensions (L x W x H) 75 x 75 x 41 mm Weight 210 g Type of mounting 2 x M5 screws; 1.5 Nm Cable length for RS-422 interface, maximum 1000 m LED display design 2 LEDs, 5 colors Standards, specifications, approvals Proof of suitability Radio to R&TTE directives EN 300330, EN 301489, CE, FCC, UL/CSA (IEC61010 / IEC61010-2-201), Ex approval

Readers 5.5 SIMATIC RF340R/RF350R - second generation SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 157 5.5.1.9 Approvals FCC information Siemens SIMATIC RF340R (MLFB 6GT2801-2BA10); FCC ID NXW-RF340R02 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement.

Readers 5.5 SIMATIC RF340R/RF350R - second generation SIMATIC RF300 158 System Manual, 07/2016, C79000-G8976-C345-0x UL information (IEC61010-1 / IEC61010-2-201) This standard applies to equipment designed to be safe at least under the following conditions: ● a) indoor use; ● b) altitude up to 2 000 m; ● c) temperature -25 °C to 70 °C; ● d) maximum relative humidity 80 % for temperature up to 31 °C decreasing linearly to 50 % relative humidity at 40 °C; ● e) TRANSIENT OVERVALTAGES up to the levels of OVERVALTAGE CATEGORY II, NOTE 1: These levels of transient overvoltage are typical for equipment supplied from the building wiring. ● f) using a "NEC Class 2" power supply is required 5.5.1.10 Dimension drawing Figure 5-21 Dimension drawing for RF340R Dimensions in mm

Readers 5.5 SIMATIC RF340R/RF350R - second generation SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 159 5.5.2 SIMATIC RF350R - second generation 5.5.2.1 Features SIMATIC RF350R Characteristics Design ① Antenna connection ② RS-422 interface ③ LED operating display Area of application Identification tasks in assembly lines in harsh industrial environments; for external antennas (ANT 1, ANT 3, ANT 12, ANT 18, ANT 30) Note Reader requires external antennas Note that the RF350R reader is designed only for operation with external antennas and only works in conjunction with the antennas ANT 1, ANT 3, ANT 12, ANT 18 or ANT 30. 5.5.2.2 Ordering data Table 5- 21 Ordering data for RF350R Article number RF350R with RS-422 interface (3964R) 6GT2801-4BA10

Readers 5.5 SIMATIC RF340R/RF350R - second generation SIMATIC RF300 160 System Manual, 07/2016, C79000-G8976-C345-0x 5.5.2.3 Pin assignment of the RS-422 interface Table 5- 22 Pin assignment Pin Pin Device end 8-pin M12 Assignment 1 + 24 V 2 - Transmit 3 0 V 4 + Transmit 5 + Receive 6 - Receive 7 Unassigned 8 Earth (shield) 5.5.2.4 LED operating display The operational statuses of the reader are displayed by two LEDs. The LEDs can adopt the colors white green, red, yellow or blue and the statuses off , on , flashing : Table 5- 23 Display elements LED Meaning The reader is turned off. The reader is turned on and is searching for transponders. The reader is in the "Setup" mode, in the "Search for transponders" status and has not yet received a "RESET" command and is not ready. / There is transponder in the antenna field. The reader is in the "Setup" mode, in the status "Show quality", has not yet re-ceived a "RESET" command and is not ready. Depending on the signal strength, the LED flashes or is lit permanently. The reader has received a "RESET" command. There is transponder in the antenna field. The reader is ready. There is an error. The number of flashes provides information about the current error. You will find more information on error messages in the section "System diag-nostics (Page 395)". 5.5.2.5 Ensuring reliable data exchange The "center point" of the transponder must be situated within the transmission window.

Readers 5.5 SIMATIC RF340R/RF350R - second generation SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 161 5.5.2.6 Metal-free area The RF350R reader does not have an internal antenna. Operation is not affected by mounting on metal or flush-mounting in metal. For information about the metal-free area required by the external antennas, refer to the corresponding section of the chapter "Antennas (Page 193)". 5.5.2.7 Technical specifications Table 5- 24 Technical specifications of the RF350R reader 6GT2801-4BA10 Product type designation SIMATIC RF350R Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range • ANT 1 • 140 mm • ANT 3 • 50 mm • ANT 12 • 16 mm • ANT 18 • 35 mm • ANT 30 • 55 mm Maximum data transmission speed reader ↔ transponder RF300 transponder ISO transponder (MDS D) ISO tran-sponder (MDS E) • Read • ≤ 8000 bytes/s • ≤ 3300 bytes/s • ≤ 3400 bytes/s • Write • ≤ 8000 bytes/s • ≤ 1700 bytes/s • ≤ 800 bytes/s Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader See section "Field data for transponders, readers and antennas (Page 48)." MTBF (Mean Time Between Failures) 260 years Interfaces Electrical connector design M12, 8-pin Antenna connector design M8, 4-pin Standard for interfaces for communication RS-422 (3964R protocol) Antenna External, antennas ANT 1, ANT 3, ANT 12, ANT 18 or ANT 30

Readers 5.5 SIMATIC RF340R/RF350R - second generation SIMATIC RF300 162 System Manual, 07/2016, C79000-G8976-C345-0x 6GT2801-4BA10 Mechanical specifications Housing • Material • Plastic PA 12 • Color • TI-Grey Recommended distance to metal 0 mm Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 55 mA Permitted ambient conditions Ambient temperature • During operation • -25 to +70 ℃ • During transportation and storage • -40 to +85 ℃ Degree of protection to EN 60529 IP65 Shock-resistant to EN 60721-3-7, Class 7 M3 50 g Vibration-resistant to EN 60721-3-7, Class 7 M3 20 g Torsion and bending load Not permitted Design, dimensions and weight Dimensions (L x W x H) 75 x 75 x 41 mm Weight 250 g Type of mounting 2 x M5 screws; 1.5 Nm Cable length for RS-422 interface, maximum 1000 m LED display design 2 LEDs, 5 colors Standards, specifications, approvals Proof of suitability Radio to R&TTE directives EN 300330, EN 301489, CE, FCC, UL/CSA (IEC61010 / IEC61010-2-201), Ex approval

Readers 5.5 SIMATIC RF340R/RF350R - second generation SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 163 5.5.2.8 Approvals FCC information Siemens SIMATIC RF350R (MLFB 6GT2801-4BA10); FCC ID NXW-RF350R02 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement.

Readers 5.5 SIMATIC RF340R/RF350R - second generation SIMATIC RF300 164 System Manual, 07/2016, C79000-G8976-C345-0x UL information (IEC61010-1 / IEC61010-2-201) This standard applies to equipment designed to be safe at least under the following conditions: ● a) indoor use; ● b) altitude up to 2 000 m; ● c) temperature -25 °C to 70 °C; ● d) maximum relative humidity 80 % for temperature up to 31 °C decreasing linearly to 50 % relative humidity at 40 °C; ● e) TRANSIENT OVERVALTAGES up to the levels of OVERVALTAGE CATEGORY II, NOTE 1: These levels of transient overvoltage are typical for equipment supplied from the building wiring. ● f) using a "NEC Class 2" power supply is required 5.5.2.9 Dimension drawing Figure 5-22 RF350R dimension drawing Dimensions in mm

Readers 5.5 SIMATIC RF340R/RF350R - second generation SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 165 5.5.3 Use of the reader in hazardous areas NOTICE Approvals for the hazardous area The approvals for the hazardous area of the readers SIMATIC RF340R und RF350R are currently in preparation.

Readers 5.6 SIMATIC RF380R SIMATIC RF300 166 System Manual, 07/2016, C79000-G8976-C345-0x 5.6 SIMATIC RF380R 5.6.1 Features SIMATIC RF380R Characteristics Design ① RS-232 or RS-422 interface ② Status display Area of application Identification tasks on assembly lines in harsh industrial environments 5.6.2 RF380R ordering data Table 5- 25 RF380R ordering data Article number RF380R with RS-232/RS-422 interface (3964R) 6GT2801-3AB10 5.6.3 Pin assignment of RF380R RS-232/RS-422 interface You can connect the RF380R reader to a higher-level system via the internal RS-422 interface or via the RS-232 interface. After connection, the interface module automatically detects which interface has been used.

Readers 5.6 SIMATIC RF380R SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 167 Note correct assignment of the pins here: Pin Pin Device end 8-pin M12 Assignment RS-232 RS-422 1 + 24 V + 24 V 2 RXD - Transmit 3 0 V 0 V 4 TXD + Transmit 5 not used + Receive 6 not used - Receive 7 not used not used 8 Ground (shield) Ground (shield) 5.6.4 LED operating display The operational statuses of the reader are displayed by the LEDs. The LED can adopt the colors green, red or yellow and the statuses off , on , flashing : Table 5- 26 LED operating display on the reader Color Meaning Operating voltage present, reader not initialized or antenna switched off Operating voltage present, reader initialized and antenna switched on 1) Transponder present Error has occurred, the type of flashing corresponds to the error code in the table in the section Error codes. The optical error display is only reset if the corresponding reset parameter ("option_1", see FC 45 / FB 45 documentation, section Input parameters) is set. 1) Only in the "with presence" mode. 5.6.5 Ensuring reliable data exchange The "center point" of the transponder must be situated within the transmission window.

Readers 5.6 SIMATIC RF380R SIMATIC RF300 168 System Manual, 07/2016, C79000-G8976-C345-0x 5.6.6 Metal-free area The RF380R can be flush-mounted in metal. Please allow for a possible reduction in the field data values. Figure 5-23 Metal-free area for RF380R To avoid any impact on the field data, the distance a should be ≥ 20 mm. 5.6.7 Minimum distance between RF380R readers RF380R side by side D ≥ 400 mm (with 2 readers) D ≥ 500 mm (with more than 2 readers) Figure 5-24 Minimum distance between RF380R readers

Readers 5.6 SIMATIC RF380R SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 169 RF380R face-to-face D ≥ 800 mm Figure 5-25 Face-to-face distance between two RF380R 5.6.8 Technical specifications Table 5- 27 Technical specifications of the RF380R reader 6GT2801-3AB10 Product type designation SIMATIC RF380R Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 200 mm Maximum data transmission speed reader ↔ transponder RF300 transponder ISO transponder • Read • approx. 8000 bytes/s • approx. 1500 bytes/s • Write • approx. 8000 bytes/s • approx. 1500 bytes/s Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader See section "Field data for transponders, readers and antennas (Page 48)." MTBF (Mean Time Between Failures) 109 years Interfaces Electrical connector design M12, 8-pin Standard for interfaces for communication RS-232/RS-422 (3964R protocol) Antenna integrated

Readers 5.6 SIMATIC RF380R SIMATIC RF300 170 System Manual, 07/2016, C79000-G8976-C345-0x 6GT2801-3AB10 Mechanical specifications Housing • Material • Plastic PA 12 • Color • Anthracite Recommended distance to metal 0 mm Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 160 mA Permitted ambient conditions Ambient temperature • During operation • -25 to +70 ℃ • During transportation and storage • -40 to +85 ℃ Degree of protection to EN 60529 IP67 Shock-resistant to EN 60721-3-7, Class 7 M3 50 g Vibration-resistant to EN 60721-3-7, Class 7 M3 20 g Torsion and bending load Not permitted Design, dimensions and weight Dimensions (L x W x H) 160 x 80 x 41 mm Weight 600 g Type of mounting 4 x M5 screws; 1.5 Nm Cable length for RS-422 interface, maximum RS-422 RS-232 1000 m 30 m LED display design 3-color LED Standards, specifications, approvals Proof of suitability Radio in accordance with R&TTE directives EN 300330, EN 301489, CE, FCC, UL/CSA, Ex: II 3G Ex nC IIB T5

Readers 5.6 SIMATIC RF380R SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 171 5.6.9 Approvals FCC information Siemens SIMATIC RF380R (MLFB 6GT2801-3AA10); FCC ID NXW-RF380R Siemens SIMATIC RF380R (MLFB 6GT2801-3AB10); FCC ID NXW-RF380R01 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement.

Readers 5.6 SIMATIC RF380R SIMATIC RF300 172 System Manual, 07/2016, C79000-G8976-C345-0x 5.6.10 Use of the reader in hazardous areas The TÜV SÜD Automotive GmbH as approved test center as well as the TÜV SÜD Product Service GmbH as certification center, identification number 0123, as per Article 9 of the Directive of the European Council of 23 March 1994 (94/9/EC), has confirmed the compliance with the essential health and safety requirements relating to the design and construction of equipment and protective systems intended for use in hazardous areas as per Annex II of the Directive. The essential health and safety requirements are satisfied in accordance with the following standards: Document Title EN 60079-0: 2006 Electrical equipment for hazardous gas atmospheres - Part 0: General requirements EN 60079-15: 2005 Electrical equipment for hazardous gas atmospheres - Part 15: Design, testing and identification of electrical equipment with type of protection "n" DIN VDE 0848-5: 2001 (in parts) Safety in electrical, magnetic and electromagnetic fields - Part 5: Explosion protection ZLS SK 107.1 Central office of the states for safety; test components Identification The identification of the electrical equipment as an enclosed unit is: II 3G Ex nC IIB T5 -25 °C to +70 °C Um=30Vdc The equipment is assigned the following references: XXXYYYZZZ [= serial number, is assigned during production] TPS 09 ATEX 1 459 X [= certificate number] "No use of the equipment in the vicinity of processes generating high charges" "Do not disconnect plug on load"

Readers 5.6 SIMATIC RF380R SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 173 5.6.11 Use of the reader in hazardous areas for gases Temperature class delineation for gases The temperature class of the reader for hazardous areas depends on the ambient temperature range: Ambient temperature range Temperature class -25 °C to +70 °C T5 WARNING Ignitions of gas-air mixtures When using the RF380R reader, check to ensure that the temperature class is observed in respect of the requirements of the area of application Non-compliance with the permitted temperature ranges while using the reader can lead to ignitions of gas-air mixtures. 5.6.12 Installation and operating conditions for the hazardous area a) The connector on the RF380R must be grounded via its supply line. b) Use of the equipment in the vicinity of processes generating high charges is not allowed. c) The plug of the RF380R must not be disconnected in a hazardous atmosphere or under load. d) The supply line for the RF380R is not part of this certificate. The supply line must exhibit a sufficient temperature resistance. e) The equipment must be mechanically protected when installed.

Readers 5.6 SIMATIC RF380R SIMATIC RF300 174 System Manual, 07/2016, C79000-G8976-C345-0x 5.6.13 Dimension drawing Figure 5-26 Dimension drawing RF380R Dimensions in mm

Readers 5.7 SIMATIC RF380R with Scanmode SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 175 5.7 SIMATIC RF380R with Scanmode You will find detailed information on the SIMATIC RF382R with Scanmode on the Industry Online Support - SIMATIC RF380R with Scanmode (https://support.industry.siemens.com/cs/ww/en/ps/15037). 5.7.1 Features RF380R Scanmode Characteristics Design ① RS232 or RS422 interface ② Status display Field of application Identification tasks on assembly lines in harsh industrial environments 5.7.2 Ordering data for RF380R with Scanmode Table 5- 28 Ordering data RF380R Scanmode Product Article number RF380R Scanmode 6GT2801-3AB20-0AX1

Readers 5.7 SIMATIC RF380R with Scanmode SIMATIC RF300 176 System Manual, 07/2016, C79000-G8976-C345-0x 5.7.3 Pin assignment RF380R Scanmode RS-232 interface You can connect the RF380R Scanmode reader via the internal RS-232/RS-422 interface to a higher-level system. (See section "Basic rules (Page 101)") Make sure that the pin assignment is correct. In the factory settings, the reader is set to RS-232. Siemens can change the interface to RS-422. Table 5- 29 Connector and reader pin assignment Pin Pin Device end 8-pin M12 Assignment RS-232 RS-422 1 + 24 V + 24 V 2 RXD - Transmit 3 0 V 0 V 4 TXD + Transmit 5 not used + Receive 6 not used - Receive 7 not used not used 8 Ground (shield) Ground (shield) 5.7.4 LED operating display The operational statuses of the reader are displayed by the LEDs. The LED can adopt the colors green, red or yellow and the statuses off , on , flashing : Table 5- 30 LED operating display on the reader Color Meaning Operating voltage present, reader ready for operation Transponder present Red LED for error display is activated permanently if correct operation of the reader cannot be guaranteed (e. g. faulty start, checksum error during operation). 5.7.5 Ensuring reliable data exchange The "center point" of the transponder must be situated within the transmission window.

Readers 5.7 SIMATIC RF380R with Scanmode SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 177 5.7.6 Metal-free area The RF380R can be flush-mounted in metal. Please allow for a possible reduction in the field data values. Figure 5-27 Metal-free area for RF380R To avoid any impact on the field data, the distance a should be ≥ 20 mm. 5.7.7 Minimum distance between several RF380R Scanmode readers RF380R side by side D ≥ 400 mm (with 2 readers) D ≥ 500 mm (with more than 2 readers) Figure 5-28 Minimum distance between RF380R readers

Readers 5.7 SIMATIC RF380R with Scanmode SIMATIC RF300 178 System Manual, 07/2016, C79000-G8976-C345-0x RF380R face-to-face D ≥ 800 mm Figure 5-29 Face-to-face distance between two RF380R 5.7.8 Technical specifications Table 5- 31 Technical specifications of the RF380R Scanmode reader 6GT2801-3AB20-0AX1 Product type designation SIMATIC RF380R Scanmode Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 200 mm Maximum data transmission speed reader ↔ transponder RF300 transponder ISO transponder • Read approx. 8000 bytes/s approx. 1500 bytes/s Transmission speed 9.6, 19.2, 38.4, 57, 115.2 kBd Read distances of the reader see section "Field data for transponders, readers and antennas (Page 48)" MTBF (Mean Time Between Failures) 109 years Interfaces Electrical connector design M12, 8-pin Standard for interfaces for communication RS-232 / RS-422 Antenna integrated Mechanical specifications Enclosure • Material • Plastic PA 12 • Color • Anthracite Recommended distance to metal 0 mm

Readers 5.7 SIMATIC RF380R with Scanmode SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 179 6GT2801-3AB20-0AX1 Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 160 mA Permitted environmental conditions Ambient temperature • During operation -25 to +70 °C • Transport and storage -40 to +85 °C Degree of protection to EN 60529 IP67 Shock-resistant to EN 60721-3-7, Class 7 M3 50 g Vibration-resistant to EN 60721-3-7, Class 7 M3 20 g Torsion and bending load Not permitted Design, dimensions and weights Dimensions (L x W x H) 160 x 80 x 41 (without M12 device connector) Weight Approx. 600 g Type of mounting 4 x M5 screws; 1.5 Nm Cable length for RS-422 interface, maximum RS-422 RS-232 1000 m 30 m LED display design 3-color LED Standards, specifications, approvals Proof of suitability Radio to R&TTE directives EN 300330, EN 301489, CE, FCC, UL/CSA

Readers 5.7 SIMATIC RF380R with Scanmode SIMATIC RF300 180 System Manual, 07/2016, C79000-G8976-C345-0x 5.7.9 Approvals FCC information Siemens SIMATIC RF380R (MLFB 6GT2801-3AB20-0AX1); FCC ID NXW-RF380R01 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement.

Readers 5.7 SIMATIC RF380R with Scanmode SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 181 5.7.10 Certificates and Approvals Certificates for USA and Canada Underwriters Laboratories (UL) acc. to standard UL 60950, Report E11 5352 and Ca-nadian standard C22.2 No. 60950 (I.T.E) or acc. to UL508 and C22.2 No. 142 (IND.CONT.EQ) 5.7.11 Dimension drawing Figure 5-30 Dimension drawing RF380R Dimensions in mm

Readers 5.8 SIMATIC RF382R with Scanmode SIMATIC RF300 182 System Manual, 07/2016, C79000-G8976-C345-0x 5.8 SIMATIC RF382R with Scanmode You will find detailed information on the SIMATIC RF382R with Scanmode on the Internet (https://support.industry.siemens.com/cs/ww/en/ps/15038). 5.8.1 Characteristics RF382R Scanmode Characteristics Design ① RS-232 or RS-422 interface ② Status display Operating range Suitable for high speeds, e.g. in • Suspension conveyor systems • Assembly lines • Production • Order picking 5.8.2 RF382R with Scanmode ordering data Table 5- 32 RF382R Scanmode ordering data Article number RF382R Scanmode 6GT2801-3AB20-0AX0

Readers 5.8 SIMATIC RF382R with Scanmode SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 183 5.8.3 Pin assignment RF382R Scanmode RS232 interface You can connect the RF382R Scanmode reader via the internal RS-232/RS-422 interface or via a higher-level system. (See section "Basic rules (Page 101)") Make sure that the pin assignment is correct. In the factory settings, the reader is set to RS-232. Siemens can change the interface to RS-422. Table 5- 33 Connector and reader pin assignment Pin Pin Device end 8-pin M12 Assignment RS-232 RS-422 1 + 24 V + 24 V 2 RXD - Transmit 3 0 V 0 V 4 TXD + Transmit 5 not used + Receive 6 not used - Receive 7 not used not used 8 Ground (shield) Ground (shield) 5.8.4 LED operating display The operational statuses of the reader are displayed by the LEDs. The LED can adopt the colors green, red or yellow and the statuses off , on , flashing : Table 5- 34 LED operating display on the reader Color Meaning Operating voltage present, reader ready for operation Transponder present Red LED for error display is activated permanently if correct operation of the reader cannot be guaranteed (e. g. faulty start, checksum error during operation). 5.8.5 Ensuring reliable data exchange The "center point" of the transponder must be situated within the transmission window. 5.8.6 Mounting on metal The RF382R can be mounted directly on metal. Flush mounting on metal is not permitted.

Readers 5.8 SIMATIC RF382R with Scanmode SIMATIC RF300 184 System Manual, 07/2016, C79000-G8976-C345-0x 5.8.7 Minimum distance between several RF382R Scanmode readers Figure 5-31 Minimum distance between several RF382R Scanmode readers Minimum distance D from RF382R to RF382R D ≥ 200 mm 5.8.8 Transmission window Orientation of fields of the SIMATIC RF382R Scanmode For many applications it may be best to operate the reader so that the tags move from left to right (or from right to left) at a certain distance in front of the narrow edge of the reader. With this direction of movement, the horizontal reader field is used, see figure below. You also have the option of moving the tags up and down (or down and up) past the narrow edge of the reader. With this direction of movement, uses the vertical reader field is used. Figure 5-32 Definition of horizontal and vertical reader field

Readers 5.8 SIMATIC RF382R with Scanmode SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 185 Maximum field strength The reader creates the maximum field approximately 13 mm below the upper reader edge. For the largest possible reading range the tags you want to read should move in this range. This applies regardless of whether the horizontal or the vertical field is used. Figure 5-33 Line of maximum magnetic field strength The area of the maximum field strength and, therefore, the maximum range is identified by a laser icon: Figure 5-34 Laser labeling

Readers 5.8 SIMATIC RF382R with Scanmode SIMATIC RF300 186 System Manual, 07/2016, C79000-G8976-C345-0x Transmission window horizontal field Figure 5-35 Distance definition horizontal field Green Main field (processing field) Blue Secondary fields, horizontal field Lx Maximum length of the main field, horizontal field d Distance from the reader edge at which maximum horizontal main field length L exists Sa Operating range in the main field Sg Limit distance ① Level 1 ② Level 2 ③ Level 3 ⇒ Direction of motion of the transponder Operating range (Sa) The operating range lies between Level ① and Level ③. The operating range between Levels ① and ② includes secondary fields. The recommended operating range therefore lies in the green main field between Level 2 and Level 3.

Readers 5.8 SIMATIC RF382R with Scanmode SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 187 Limit distance (Sg) The limit distance lies on Level ③. Transmission window vertical field Figure 5-36 Distance definition vertical field Green Main field (processing field) Ly Maximum length of the main field, vertical field d Distance from the reader edge at which maximum vertical main field length Ly exists Sa Operating range in the main field Sg Limit distance Dopt = 13 mm ⇓ Direction of motion of the transponder

Readers 5.8 SIMATIC RF382R with Scanmode SIMATIC RF300 188 System Manual, 07/2016, C79000-G8976-C345-0x 5.8.9 Technical specifications Table 5- 35 Technical specifications of the RF382R reader with Scanmode 6GT2801-3AB20-0AX0 Product type designation SIMATIC RF382R Scanmode Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 75 mm Maximum data transmission speed reader ↔ transponder ISO transponder • Read • approx. 1500 bytes/s Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader See section "Field data for transponders, readers and antennas (Page 48)." MTBF (Mean Time Between Failures) 115 years Interfaces Electrical connector design M12, 8-pin Standard for interfaces for communication RS-232 (factory setting, can be changed to RS-422) Antenna integrated Mechanical specifications Housing • Material • Plastic PA 12 • Color • Anthracite Recommended distance to metal 0 mm Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 140 mA

Readers 5.8 SIMATIC RF382R with Scanmode SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 189 6GT2801-3AB20-0AX0 Permitted ambient conditions Ambient temperature • During operation • -25 to +70 ℃ • During transportation and storage • -40 to +85 ℃ Degree of protection to EN 60529 IP67 Shock-resistant to EN 60721-3-7, Class 7 M3 50 g Vibration-resistant to EN 60721-3-7, Class 7 M3 20 g Torsion and bending load Not permitted Design, dimensions and weight Dimensions (L x W x H) 160 x 80 x 41 mm Weight 550 g Type of mounting 4 x M5 screws; 1.5 Nm Cable length for RS-422 interface, maximum RS-422 RS-232 1000 m 30 m LED display design 3-color LED Standards, specifications, approvals Proof of suitability Radio to R&TTE directives EN 300330, EN 301489, CE, FCC, UL/CSA 5.8.10 Approvals FCC information Siemens SIMATIC RF382R (MLFB 6GT2801-3AB20-0AX0); FCC ID NXW-RF382R This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Readers 5.8 SIMATIC RF382R with Scanmode SIMATIC RF300 190 System Manual, 07/2016, C79000-G8976-C345-0x Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement. Certificates for USA and Canada Underwriters Laboratories (UL) acc. to standard UL 60950, Report E11 5352 and Ca-nadian standard C22.2 No. 60950 (I.T.E) or acc. to UL508 and C22.2 No. 142 (IND.CONT.EQ)

Readers 5.8 SIMATIC RF382R with Scanmode SIMATIC RF300 System Manual, 07/2016, C79000-G8976-C345-0x 191 5.8.11 Dimensional diagram Figure 5-37 Dimension drawing

Readers 5.8 SIMATIC RF382R with Scanmode SIMATIC RF300 192 System Manual, 07/2016, C79000-G8976-C345-0x

Navigation menu