Siemens Albatros Zone Controler Ce1U2353En01A Users Manual 012_Albatros2_U2353en_01a
CE1U2353en01a to the manual e0294b14-85a2-46ca-9f11-3da800f92707
2015-02-05
: Siemens Siemens-Albatros-Zone-Controler-Ce1U2353En01A-Users-Manual-410627 siemens-albatros-zone-controler-ce1u2353en01a-users-manual-410627 siemens pdf
Open the PDF directly: View PDF 
.
Page Count: 26
| Download | |
| Open PDF In Browser | View PDF |
Albatros2 Zone controler User Manual OEM Edition 1.0 Controller series A CE1U2353en01a 22. November 2006 RVS46.. AVS75.. AVS37.. QAA75.. QAA78.. QAA55.. Building Technologies HVAC Products 2/26 Siemens Schweiz AG HVAC Products User Manual OEM CE1U2353en01a 22. November 2006 Table of contents 1 Overview of OEM settings ............................................................................... 4 2 The settings in detail...................................................................................... 15 2.1 Operator section ............................................................................................ 15 Operation and display.................................................................................... 15 2.2 Heating circuits .............................................................................................. 15 mixing valve control ....................................................................................... 15 2.3 Domestic hot water........................................................................................ 16 Setpoints........................................................................................................ 16 Release ......................................................................................................... 16 2.4 Pump H1/H2 .................................................................................................. 17 pump H1 ........................................................................................................ 17 2.5 Primary controller / system pump .................................................................. 17 flow temperature setpoint limitations ............................................................. 17 mixing valve control ....................................................................................... 18 2.6 DHW storage tank ......................................................................................... 19 Release ......................................................................................................... 19 Charging control ............................................................................................ 19 Charging time limitation ................................................................................. 20 Discharging protection................................................................................... 20 Overtemperature protection........................................................................... 21 DHW push ..................................................................................................... 21 2.7 Configuration ................................................................................................. 21 Building and room model............................................................................... 21 Parameters .................................................................................................... 22 2.8 LPB................................................................................................................ 22 Error / maintenance / alarms ......................................................................... 22 Range of action of changeover...................................................................... 22 2.9 Error............................................................................................................... 23 History 1...10 ................................................................................................. 23 2.10 Diagnostics consumers ................................................................................. 23 Heating circuit 1, heating circuit 2, heating circuit P ..................................... 23 3/26 Siemens Schweiz AG HVAC Products User Manual OEM Table of contents CE1U2353en01a 22. November 2006 1 Overview of OEM settings The table below shows all available settings up to the heating engineer level. However, certain operating lines may be hidden, depending on the type of unit. Max Unit O = OEM Minimum Function User level Operating line Time of day and date 1 E Hours/minutes 2 E Day/month 3 E Year 5 F Start of summertime 6 F End of summertime Operator section 20 E Language F = heating engineer Default value E = enduser I = commissioning BZ = operating line Legend 25.03 25.10 00:00 01.01 2004 01.01 01.01 23:59 31.12 2099 31.12 31.12 hh:mm dd.mm yyyy dd.mm dd.mm German - Temporarily - Off - Off - German ¦ … 22 F Info Temporarily ¦ Permanently 26 F Operation lock Off ¦ On 27 F Programming lock Off ¦ On 30 O Data:read No No ¦ Yes 31 O Data:write No No ¦ Yes 40 I Used as Room unit 1 - Heating circuit 1 - Commonly with HC1 - Commonly with HC1 - Heating circuit 1 - Room unit 1 ¦ Room unit 2 ¦ Operator unit ¦Service unit 42 I assignment room unit 1 Heating circuit 1 ¦ Heating circuits 1 and 2 44 I Operation HC2 Commonly with HC1 ¦ Independently 46 I Operation HCP Commonly with HC1 ¦ Independently 48 I Action occupancy button None ¦ Heating circuit 1 ¦ Heating circuit 2 ¦ Commonly 54 F 70 F Wireless 120 I Readjustment room sensor Software version 0.0 - Binding No -3 0 3 99.9 °C - No ¦ Yes 121 I Test mode Off Off ¦ On 130 I Room unit 1 - - - - - - - - Missing ¦ Ready ¦ No reception ¦ Change batt 131 I Room unit 2 Missing ¦ Ready ¦ No reception ¦ Change batt 132 I Outside sensor Missing ¦ Ready ¦ No reception ¦ Change batt 133 I Repeater Missing ¦ Ready ¦ No reception 4/26 Siemens Schweiz AG HVAC Products User Manual OEM Overview of OEM settings CE1U2353en01a 22. November 2006 Default value - Unit Function Operator unit Max User level I Minimum Operating line 134 - - - No - Mo - Su - Missing ¦ Ready ¦ No reception ¦ Change batt 135 I Service unit Missing ¦ Ready ¦ No reception ¦ Change batt 138 I Delete all devices No ¦ Yes Time prog heating circuit 1 500 E Preselection Mo - Su ¦ Mo - Fr ¦ Sa - Su ¦ Mo ¦ Tu ¦ We ¦ Th ¦ Fr ¦ Sa ¦Su 501 502 503 504 505 506 516 E E E E E E E 1st phase on 1st phase off 2st phase on 2st phase off 3st phase on 3st phase off Default values 6:00 22:00 24:00 24:00 24:00 24:00 No 00:00 00:00 00:00 00:00 00:00 00:00 24:00 24:00 24:00 24:00 24:00 24:00 hh:mm hh:mm hh:mm hh:mm hh:mm hh:mm - No ¦ Yes Time prog heating circuit 2 520 E Preselection Mo - Su - Mo - Su ¦ Mo - Fr ¦ Sa - Su ¦ Mo ¦ Tu ¦ We ¦ Th ¦ Fr ¦ Sa ¦Su 521 522 523 524 525 526 536 E E E E E E E 1st phase on 1st phase off 2st phase on 2st phase off 3st phase on 3st phase off Default values 6:00 22:00 24:00 24:00 24:00 24:00 No 00:00 00:00 00:00 00:00 00:00 00:00 24:00 24:00 24:00 24:00 24:00 24:00 hh:mm hh:mm hh:mm hh:mm hh:mm hh:mm - No ¦ Yes Time program 3 / HCP 540 E Preselection Mo - Su - Mo - Su ¦ Mo - Fr ¦ Sa - Su ¦ Mo ¦ Tu ¦ We ¦ Th ¦ Fr ¦ Sa ¦Su 541 542 543 544 545 546 556 E E E E E E E 1st phase on 1st phase off 2st phase on 2st phase off 3st phase on 3st phase off Default values 6:00 22:00 24:00 24:00 24:00 24:00 No 00:00 00:00 00:00 00:00 00:00 00:00 24:00 24:00 24:00 24:00 24:00 24:00 hh:mm hh:mm hh:mm hh:mm hh:mm hh:mm - No ¦ Yes Time program 4 / DHW 560 E Preselection Mo - Su - Mo - Su ¦ Mo - Fr ¦ Sa - Su ¦ Mo ¦ Tu ¦ We ¦ Th ¦ Fr ¦ Sa ¦Su 561 562 563 564 565 566 E E E E E E 1st phase on 1st phase off 2st phase on 2st phase off 3st phase on 3st phase off 6:00 22:00 24:00 24:00 24:00 24:00 00:00 00:00 00:00 00:00 00:00 00:00 24:00 24:00 24:00 24:00 24:00 24:00 hh:mm hh:mm hh:mm hh:mm hh:mm hh:mm 5/26 Siemens Schweiz AG HVAC Products User Manual OEM Overview of OEM settings CE1U2353en01a 22. November 2006 - Periode 1 - Unit No Max Default values Minimum Default value User level E Function Operating line 576 No ¦ Yes Holidays heating circuit 1 641 E Preselection Period 1 ¦ Period 2 ¦ Period 3¦ Period 4¦ Period 5¦ Period 6¦ Period 7¦ Period 8 642 643 648 E E E Start End Operating level --.-01.01 --.-01.01 Frost protection 31.12 31.12 dd.mm dd.mm - Frost protection ¦ Reduced Holidays heating circuit 2 651 E Preselection Periode 1 - Period 1 ¦ Period 2 ¦ Period 3¦ Period 4¦ Period 5¦ Period 6¦ Period 7¦ Period 8 652 653 658 E E E Start End Operating level --.-01.01 --.-01.01 Frost protection 31.12 31.12 dd.mm dd.mm - Frost protection ¦ Reduced Holidays heating circuit P 661 E Preselection Periode 1 - Period 1 ¦ Period 2 ¦ Period 3¦ Period 4¦ Period 5¦ Period 6¦ Period 7¦ Period 8 662 663 668 E E E Start End Operating level --.-01.01 --.-01.01 Frost protection 31.12 31.12 dd.mm dd.mm - 20.0 16 10.0 35.0 1.50 0.0 Off BZ 712 BZ 714 4 BZ 710 0.10 -4.5 BZ 716 BZ 710 BZ 712 35 4.00 4.5 °C °C °C °C °C - 18 −−−/8 -3 − − − / -10 8 8 80 BZ 740 20 −−−/0 −−− − − − / 0.5 5 −−−/0 Down to reduced setpoint 30 10 BZ 741 95 100 4 20 °C °C °C °C % °C °C - 0 0 −−− -15 On 0 0 − − − / -30 -30 360 360 10 BZ 800 min min °C °C - 10 0 50 °C Frost protection ¦ Reduced Heating circuit 1 710 E Comfort cooling setpoint 712 E Reduced setpoint 714 E Frost protection setpoint 716 F Comfort setpoint max 720 E Heating curve slope 721 F Heating curve displacement 726 F Heating curve adaption Off ¦ On 730 732 740 741 750 760 770 780 E F I I F F F F Summer/winter heating limit 24-hour heating limit Flow temp setpoint min Flow temp setpoint max Room influence Room temp limitation Boost heating Quick setback Off ¦ Down to reduced setpoint ¦ Down to frost prot setpoint 790 791 800 801 820 F F F F F Optimum start control max Optimum stop control max Reduced setp increase start Reduced setp increase end Overtemp prot pump circuit 830 F Mixing valve boost Off ¦ On 6/26 Siemens Schweiz AG HVAC Products User Manual OEM Overview of OEM settings CE1U2353en01a 22. November 2006 Default value 3-position Unit Function Actuator:type Max User level F Minimum Operating line 832 - 2-position ¦ 3-position 833 834 835 836 850 F F O O I Switching differential 2-pos Actuator: running time Mixing valve Xp Mixing valve Tn Floor curing function 2 120 32 120 Off 0 30 1 10 20 873 100 873 °C s °C s - 95 °C BZ 1012 BZ 1014 4 BZ 1010 0.10 -4.5 BZ 1016 BZ 1010 BZ 1012 35 4.00 4.5 °C °C °C °C °C - 18 −−−/8 -3 − − − / -10 8 8 80 BZ 1040 20 −−−/0 −−− − − − / 0.5 5 −−−/0 Down to reduced setpoint 30 10 BZ 1041 95 100 4 20 °C °C °C °C % °C °C - 0 0 −−− -15 On 360 360 10 BZ 1100 min min °C °C - 10 0 3-position 50 °C - 2 120 32 120 Off 20 873 100 873 °C s °C s - Off ¦ Functional heating ¦ Curing heating ¦ Functional/curing heating¦ Manually 851 861 I F Floor curing setp manually Excess heat draw 25 0 Always Off ¦ Heating mode ¦ Always 872 F With prim contr/system pump Yes No ¦ Yes 900 I Optg mode changeover Protection Protection ¦ Recuced Heating circuit 2 1010 E Comfort cooling setpoint 1012 E Reduced setpoint 1014 E Frost protection setpoint 1016 F Comfort setpoint max 1020 E Heating curve slope 1021 F Heating curve displacement 1026 F Heating curve adaption 20.0 16 10.0 35.0 1.50 0.0 Off Off ¦ On 1030 1032 1040 1041 1050 1060 1070 1080 E F I I F F F F Summer/winter heating limit 24-hour heating limit Flow temp setpoint min Flow temp setpoint max Room influence Room temp limitation Boost heating Quick setback Off ¦ Down to reduced setpoint ¦ Down to frost prot setpoint 1090 1091 1100 1101 1120 F F F F F Optimum start control max Optimum stop control max Reduced setp increase start Reduced setp increase end Overtemp prot pump circuit 1130 1132 F F Mixing valve boost Actuator:type 1133 1134 1135 1136 1150 F F O O F Switching differential 2-pos Actuator: running time Mixing valve Xp Mixing valve Tn Floor curing function 0 0 − − − / -30 -30 Off ¦ On 2-position ¦ 3-position 0 30 1 10 Off ¦ Functional heating ¦ Curing heating ¦ Functional/curing heating¦ Manually 7/26 Siemens Schweiz AG HVAC Products User Manual OEM Overview of OEM settings CE1U2353en01a 22. November 2006 Default value 25 0 Always 1172 F With prim contr/system pump Unit Function Floor curing setp manually Excess heat draw Max User level F F Minimum Operating line 1151 1161 95 °C Off ¦ Heating mode ¦ Always Yes No ¦ Yes 1200 I Optg mode changeover Protection Protection ¦ Recuced Heating circuit P 1300 E Operating mode Automatic - Protection ¦ Automatic ¦ Reduced ¦ Comfort 1310 1312 1314 1316 1320 1321 1326 E E E F E F F 1330 1332 1340 1341 1350 1360 1370 1380 E F F F F F F F Comfort cooling setpoint Reduced setpoint Frost protection setpoint Comfort setpoint max Heating curve slope Heating curve displacement Heating curve adaption 20.0 16 10.0 35.0 1.50 0.0 Off BZ 1012 BZ 1014 4 BZ 1010 0.10 -4.5 BZ 1016 BZ 1010 BZ 1012 35 4.00 4.5 °C °C °C °C °C - 18 −−−/8 -3 − − − / -10 8 8 80 BZ 1040 20 −−−/0 −−− − − − / 0.5 5 −−−/0 Down to reduced setpoint 30 10 BZ 1041 95 100 4 20 °C °C °C °C % °C °C - 0 0 −−− -15 On 360 360 10 BZ 1100 min min °C °C - Off ¦ On Summer/winter heating limit 24-hour heating limit Flow temp setpoint min Flow temp setpoint max Room influence Room temp limitation Boost heating Quick setback Off ¦ Down to reduced setpoint ¦ Down to frost prot setpoint 1390 1391 1400 1401 1420 F F F F F Optimum start control max Optimum stop control max Reduced setp increase start Reduced setp increase end Overtemp prot pump circuit 0 0 − − − / -30 -30 Off ¦ On 1450 I Floor curing function Off - Off ¦ Functional heating ¦ Curing heating ¦ Functional/curing heating¦ Manually 1451 1455 1456 1461 I F F F Floor curing setp manually Floor curing setp current Floor curing day current Excess heat draw 25 0 0 0 0 0 Always 95 95 32 °C °C °C BZ 1614 OEM BZ 1610 80 °C °C °C - Off ¦ Heating mode ¦ Always 1172 F With prim contr/system pump Yes No ¦ Yes 1500 I Optg mode changeover Protection Protection ¦ Recuced Domestic hot water 1610 E Nominal setpoint 1612 F Reduced setpoint 1614 O Nominal setpoint max 1620 I Release 55 BZ 1612 40 8 65 8 Time programs HCs 24h/day ¦ Time programs HCs ¦ Time program 4/DHW 8/26 Siemens Schweiz AG HVAC Products User Manual OEM Overview of OEM settings CE1U2353en01a 22. November 2006 Default value MC shifting, PC absolute Unit Function Charging priority Max User level I Minimum Operating line 1630 - Fixed weekday - Absolute ¦ Shifting ¦ None ¦ MC shifting, PC absolute 1640 F Legionella function Off ¦ Periodically ¦ Fixed weekday 1641 1642 F F Legionella funct periodically Legionella funct weekday 3 1 Montag 7 Days −−− 65 30 On 23:50 95 360 hh:mm °C min - Monday ¦ Tuesday ¦ Wednesday ¦ Thursday ¦ Friday ¦ Saturday ¦ Sunday 1644 1645 1646 1647 F F F F 1660 F Legionella funct time Legionella funct setpoint Legionella funct duration Legionella funct circ pump − − − / 00:00 55 − − − / 10 Off ¦ On Release of the circulating pump DHW release - On - Time program 3/HCP ¦ DHW release ¦ Time program 4/DHW 1661 F Circulating pump cycling Off ¦ On 1663 F Circulaton setpoint Pump H1/H2 2008 O H1 DHW charging priority 45 8 80 °C Yes No ¦ Yes 2010 F H1 Excess heat draw On Off ¦ On 2014 F H1 prim contr/system pump Yes - No ¦ Yes 2033 O H2 DHW charging priority Yes No ¦ Yes 2035 F H2 Excess heat draw On Off ¦ On 2039 F H2 prim contr/system pump Yes - No ¦ Yes Primary controller / system pump 2110 O Flow temp setpoint min 2111 O Flow temp setpoint max 2130 O Mixing valve boost 2132 O Actuator:type 8 8 80 8 10 0 3-position 95 95 50 °C °C °C 2-position ¦ 3-position 2133 2134 2135 2136 Solar 3810 3811 3812 3830 3831 3840 3850 3860 O O O O Switching differential 2-pos Actuator: running time Mixing valve Xp Mixing valve Tn 2 120 32 120 0 30 1 10 20 873 100 873 °C °C °C °C F F F F F F F F Temp diff on Temp diff off Charg temp min DHW st tank Collector start function Min run time collector pump Collector frost protection Collector overtemp prot Evaporation heat carrier 8 4 −−− −−− 60 −−− −−− −−− BZ 3811 0 −−−/8 −−−/5 5 − − − / -20 − − − / 30 − − − / 60 40 BZ 3812 95 60 120 5 200 200 °C °C °C min s °C °C °C 9/26 Siemens Schweiz AG HVAC Products User Manual OEM Overview of OEM settings CE1U2353en01a 22. November 2006 Max Unit Minimum Default value Function User level Operating line DHW storage tank 5010 O Charging 16 0 With B3/B31 30 °C 5 0 150 − − − / 10 Automatic 20 600 °C min 80 90 60 Off BZ 5051 OEM 95 95 °C °C °C - Several times / day Once/day ¦ Several times/day 5020 5022 F F Increase of the flow temperature setpoint Type of charging 5024 5030 5040 O O O Switching diff Charging time limitation Discharging protection 5050 5051 5055 5056 F O F F Charging temp max Storage tank temp max Recooling temp Recooling heat gen/HCs 5057 F Recooling collector With B3 ¦ With B3/B31 ¦ With B3, legio B3/B31 Off ¦ Always ¦ Automatically 8 8 8 Off ¦ On Off - Substitute - DHW release - DHW sensor - Off ¦ Summer ¦ Always 5060 F Electric immersion heater:operating mode Substitute ¦ Summer ¦ Always 5061 F Electric immersion heater:release 24h/day ¦ DHW release¦ Time program4/ DHW 5062 F El immersion heater control External thermostat ¦ DHW sensor 5070 O Automatic push On Off ¦ On 5085 F Excess heat draw On - Off ¦ On 5092 F With prim contr/system pump No No ¦ Yes 5093 F With solar integration Yes No ¦ Yes Configuration 5710 I Heating circuit 1 On - On - Sensors - charging pump - None - None - None - Off ¦ On 5715 I Heating circuit 2 Off ¦ On 5730 I DHW sensor B3 Sensor ¦ Thermostat 5731 I DHW controlling element Q3 None ¦ Charging pump ¦ Diverting valve 5890 I Relay output QX1 None ¦ Circulating pump Q4 ¦ El imm heater DHW K6 ¦ Collector pump Q5 ¦ H1 pump Q15 ¦ Alarm output K10 ¦ 2nd pump speed HC1 Q21 ¦ 2nd pump speed HC2 Q22 ¦ 2nd pump speed HCP Q23 ¦ Heat circuit pump HCP Q20 ¦ H2 pump ¦ Q18 primary pump Q14 5930 I Sensor input BX1 None ¦ DHW sensor B31 ¦ Collector sensor B6 ¦ DHW circulation sensor B39 5931 I Sensor input BX2 None ¦ DHW sensor B31 ¦ Collector sensor B6 ¦ DHW circulation sensor B39 10/26 Siemens Schweiz AG HVAC Products User Manual OEM Overview of OEM settings CE1U2353en01a 22. November 2006 Function input H1 Optg mode change HCs+DHW ¦ Optg mode changeover HCs ¦ Optg mode changeover HC1 ¦ Optg mode changeover HC2 ¦ Optg mode changeover HCP ¦ Error/alarm message ¦ Min flow temp setpoint ¦ Excess heat discharge 5951 I Contact type H1 Unit Max Minimum Default value User level I Function Operating line 5950 Optg mode change HCs+DHW - NO contact - NC ¦ NO 5952 5954 5956 5960 I I I I Min flow temp setpoint H1 Heat request 10V H1 Pressure value 3.5V H1 Function input H2 Optg mode change HCs+DHW ¦ Optg mode changeover HCs ¦ Optg mode changeover HC1 ¦ Optg mode changeover HC2 ¦ Optg mode changeover HCP ¦ Heat generation lock ¦ Error/alarm message ¦ Min flow temp setpoint ¦ Heat request ¦ Pressure measurement 5961 I Contact type H2 70 8 100 5 5.0 0.0 Optg mode change HCs+DHW 120 130 10.0 NO contact °C °C bar - - NC ¦ NO 5962 6014 I I Min flow temp setpoint H2 Function mixing group 1 70 8 Heating circuit 120 °C - Heating circuit ¦ Prim contr/system pump 6020 I Function extension module 1 No function - No function - None ¦ Multi-functional ¦ Heating circuit ¦ Solar DHW ¦ Prim contr/system pump 6021 I Function extension module 2 None ¦ Multi-functional ¦ Heating circuit ¦ Solar DHW ¦ Prim contr/system pump 6097 F Sensor type collector NTC NTC 10k ¦ Platinum 1000 6030 I Relay output QX21 None - None - None - None - None ¦ Circulating pump Q4 ¦ El imm heater DHW K6 ¦ Collector pump Q5 ¦ H1 pump Q15 ¦ Alarm output K10 ¦ 2nd pump speed HC1 Q21 ¦ 2nd pump speed HC2 Q22 ¦ 2nd pump speed HCP Q23 ¦ Heat circuit pump HCP Q20 ¦ H2 pump ¦ Q18 primary pump Q14 6031 I Relay output QX22 None ¦ Circulating pump Q4 ¦ El imm heater DHW K6 ¦ Collector pump Q5 ¦ H1 pump Q15 ¦ Alarm output K10 ¦ 2nd pump speed HC1 Q21 ¦ 2nd pump speed HC2 Q22 ¦ 2nd pump speed HCP Q23 ¦ Heat circuit pump HCP Q20 ¦ H2 pump ¦ Q18 primary pump Q14 6040 I Sensor input Bx21 None ¦ DHW sensor B31 ¦ Collector sensor B6 ¦ DHW circulation sensor B39 6041 I Sensor input BX22 None ¦ DHW sensor B31 ¦ Collector sensor B6 ¦ DHW circulation sensor B39 Sensor type collector 6097 NTC NTC 10k ¦ Platinum 1000 6098 6100 6110 6112 6120 F F F O F Readjustm collector sensor Readjustm outside sensor Time constant building Gradient room model Frost protection plant 0 0.0 15 60 On -20 -3.0 0 0 20 3.0 50 300 °C °C h min/°C - Off ¦ On 6200 I Saving sensors No - No ¦ Yes 11/26 Siemens Schweiz AG HVAC Products User Manual OEM Overview of OEM settings CE1U2353en01a 22. November 2006 Default value No Unit Function Save parameters Max User level O Minimum Operating line 6204 No ¦ Yes 6205 F Reset to default parameters No - No ¦ Yes 6212 6215 6217 6220 6222 LPB 6600 6601 6604 I I I F O Check no heat source 1 Check no storage tank Check no heating circuits Software version Device hours run 0 0 0 0 0 0 I F F Device address Segment address Bus power supply function 1 0 0 0 Automatic 199999 199999 199999 99.9 500 000 h 16 14 - Off ¦ Automatically 6605 F Bus power supply state On - Off ¦ On 6610 O Display system messages Yes No ¦ Yes 6612 O Alarm delay No No ¦ Yes 6620 O Action changeover functions System - Local - All heating circuits in the system Autonomous - Segment ¦ System 6621 F Summer changeover Locally¦ Centrally 6625 F DHW assignment Local HCs ¦ All HCs in segment ¦ All HCs in system 6640 I Clock mode - Autonomously ¦ Slave without remote ¦ Slave with remote setting ¦ Master 6650 Error 6710 F Outside temp source 0 I Reset:alarm relay No 0 239 - No ¦ Yes 6740 6741 6800 6802 6804 6806 6808 6810 6812 6814 F F F F F F F F F F F F F F F F F F Flow temp 1 alarm Flow temp 2 alarm History 1 Error code 1 History 2 Error code 1 History 3 Error code 1 History 4 Error code 1 History 5 Error code 1 History 6 Error code 6 History 7 Error code 7 History 8 Error code 8 −−− −−− - − − − / 10 − − − / 10 240 240 min min 0 255 - 0 255 - 0 255 - 0 255 - 0 255 - 0 255 - 0 255 - 0 255 - 12/26 Siemens Schweiz AG HVAC Products User Manual OEM Overview of OEM settings CE1U2353en01a 22. November 2006 No Unit History 9 Error code 9 History 10 Error code 10 Reset history Max F F F F O Minimum Default value 6820 Function 6818 User level Operating line 6816 0 255 - 0 255 - No ¦ Yes Maintenance/service 7140 E manual control Off - Off ¦ On 7150 I Simulation outside temp 7170 I Telephone customer service Input/output test 7700 I Relay test - -50.0 50 No test °C - No test ¦ Everything off ¦ DHW pump Q3 ¦ Heating circuit pump Q2 ¦ Heat circ mix valve op Y1 ¦ Heat circ mix valve cl Y2 ¦ Relay output QX1 ¦ Relay output QX21 module 1 ¦ Relay output QX22 module 1 ¦ Relay output QX23 module 1¦ Relay output QX21 module 2 ¦ Relay output QX22 module 2 ¦ Relay output QX23module 2 7730 7732 7750 7820 7821 7830 7831 7832 7833 7841 I I I I I I I I I I Outside temp B9 Flow temp B1 DHW temp B3 Sensor temp BX1 Sensor temp BX2 Sensor temp BX21 module 1 Sensor temp BX22 module 1 Sensor temp BX21 module 2 Sensor temp BX22 module 2 Contact state H1 0 0 0 0 Open -50.0 0.0 0.0 -28.0 -28.0 -28 -28 -28 -28 50 140 140 350 350 350 350 350 350 °C °C °C °C °C °C °C °C °C - Open ¦ Closed 7846 I Contact state H2 Open - - - Open ¦ Closed Status: 8000 I State heating circuit 1 8001 I State heating circuit 2 8002 I State heating circuit P 8003 I State DHW 8007 I State solar Diagnostics heat source 8510 I Collector temp 1 8511 I Collector temp 1 max 8512 I Collector temp 1 min 8513 I dT collector 1/DHW 8514 I dT collector 1/buffer 8530 F Hours run solar yield 8531 F Hours run collect overtemp Diagnostics consumers 8700 I Outside temperature 8703 I Outside temp attenuated 8704 I Composite outside temperature 0 0 - -28.0 -28.0 -28.0 -28.0 -28.0 0 0 350 350 350 350 350 65535 65535 °C °C °C °C °C h h - -50.0 -50.0 -50.0 50.0 50.0 50.0 °C °C °C 13/26 Siemens Schweiz AG HVAC Products User Manual OEM Overview of OEM settings CE1U2353en01a 22. November 2006 Default value - Unit Function Heating circuit pump Q2 Max User level I Minimum Operating line 8730 - - - - - Off ¦ On 8731 I Heat circ mix valve op Y1 Off ¦ On 8732 I Heat circ mix valve cl Y2 Off ¦ On 8740 8741 8742 8743 8744 8760 I I O I I I 8761 I Room temp 1 Room setpoint 1 Room temp 1 model Flow temp 1 Flow temp setpoint 1 Heating circuit pump Q6 - 0.0 4.0 0.0 0.0 0.0 50.0 35.0 50.0 140.0 140.0 °C °C °C °C °C - Off ¦ On Heat circ mix valve op Y5 - - - - Off ¦ On 8762 I Heat circ mix valve cl Y6 Off ¦ On 8770 8771 8772 8773 8774 8800 8801 8802 8803 8820 I I O I I I I O I I 8830 8831 8832 8835 8930 8931 8950 8951 9000 9001 9031 I I I I I I I I I I I 9050 I Room temp 2 Room setpoint 2 Room temp 2 model Flow temp 2 Flow temp setpoint 2 Room temp P Room setpoint P Room temp P model Flow temp setpoint P DHW pump Q3 - 0.0 4.0 0.0 0.0 0.0 0.0 4.0 0.0 0.0 50.0 35.0 50.0 140.0 140.0 50.0 35.0 50.0 140.0 °C °C °C °C °C °C °C °C °C - - 0.0 8.0 0.0 0.0 0.0 0.0 0.0 0.0 5.0 5.0 140.0 80.0 140.0 140.0 140.0 140.0 140.0 140.0 130.0 130.0 °C °C °C °C °C °C °C °C °C °C - Off ¦ On DHW temp 1 DHW temp setpoint DHW temp 2 DHW circulation temp Primary controller temp Primary controller setpoint Common flow temp Common flow temperature setpoint Flow temp setpoint H1 Flow temp setpoint H2 Relay output QX1 Off ¦ On Relay output QX21 module 1 - - - - - - - - - - - - Off ¦ On 9051 I Relay output QX22 module 1 Off ¦ On 9052 I Relay output QX23 module 1 Off ¦ On 9053 I Relay output QX21 module 2 Off ¦ On 9054 I Relay output QX22 module 2 Off ¦ On 9055 I Relay output QX23 module 2 Off ¦ On 14/26 Siemens Schweiz AG HVAC Products User Manual OEM Overview of OEM settings CE1U2353en01a 22. November 2006 2 The settings in detail 2.1 Operator section Operation and display Line no. Operating line 30 Data:read No Yes 31 Data:write No Yes Data:read The setting data of all operating levels are copied from the controller to the memory of the operator unit. This means that previous data in the operator unit will be overwritten. Data:write With the exception of the data listed below, the setting data of all operating levels are transferred from the memory of the operator unit to the connected controller. Previous setting data in the controller will be overwritten. The following data will not be overwritten: Line no. 3 130 131 132 133 134 135 138 516 536 556 576 6222 6600 6601 6650 Operating line Year Room unit 1 Room unit 2 Outside sensor Repeater Operator unit Service unit Delete all devices default values default values default values default values Device hours run device address Segment address Outside temp source 2.2 Heating circuits mixing valve control HC1 835 836 Line no. HC2 HC3P 1135 1136 Operating line Mixing valve Xp Mixing valve Tn Mixing valve Xp The proportional band defines within which change of the control variable ∆x (∆T of the flow) the whole correcting span y (valve travel) is traversed. The smaller the proportional band, the greater the change of the manipulated variable ∆y at a given change of the controlled variable ∆x. Mixing valve Tn The integral action time is the period of time the controller’s I-part would require to produce the same change of the manipulated variable as the P-part 15/26 Siemens Schweiz AG HVAC Products User Manual OEM The settings in detail CE1U2353en01a 22. November 2006 An adjustment of the integral action time changes the valve’s rate of response. The longer the integral action time Tn, the slower the response of the controlled system. 2392Z08 y 1 Xp t Tn x t @ 2.3 Domestic hot water Setpoints Line no. Operating line 1614 Nominal setpoint max This operating line is used to limit the “Nominal setpoint“ (operating line 1610) at the top. Release Line no. Operating line 1620 Release 24h/day Time programs HCs Time program 4 / DHW 24h/day The DHW temperature is constantly maintained at the nominal DHW setpoint, independent of any time programs. 2371Z18 Example: 0 6 12 18 24 h Time programs HCs The DHW setpoint is switched between the nominal DHW setpoint and the reduced DHW setpoint according to the heating circuits’ time programs. The first switch-on point of each period is shifted forward in time by one hour. 16/26 Siemens Schweiz AG HVAC Products User Manual OEM The settings in detail CE1U2353en01a 22. November 2006 2377Z16 Example: 0 5 6 12 16 17 h 24 Time program 4 / DHW For DHW heating, time switch program 4 of the local controller is used. The set switching times of that program are used to switch between the nominal DHW setpoint and the reduced DHW setpoint. This way, the DHW is heated independently of the heating circuits. 2373Z24 Example: 0 6 12 18 24 h 2.4 Pump H1/H2 pump H1 Line no. H1 H2 2008 2033 Operating line H1/H2 DHW charging priority Off ¦ On H1/H2 DHW charging priority When using this setting, the connected pump H1/H2 can be excluded from / included in the effect of DHW charging priority. In the case of a ventilation system, for example, it is thus possible to ensure a constant supply of heat with no impact from DHW charging priority. 2.5 Primary controller / system pump flow temperature setpoint limitations Line no. Operating line 2110 2111 Flow temp setpoint min Flow temp setpoint max Using this limitation, a temperature range for the flow temperature setpoint can be defined. If the requested flow temperature setpoint reaches the relevant limit and the heat request increases or decreases, the flow temperature setpoint will be maintained at the maximum or minimum limit. 17/26 Siemens Schweiz AG HVAC Products User Manual OEM The settings in detail CE1U2353en01a 22. November 2006 TVmax max TVw 2358Z09 TV akt TVmin min 0 10 TVw TVmax Tvmin 20 30 40 50 60 70 80 90 100 °C Current flow temperature setpoint Flow temperature setpoint maximum Flow temp setpoint min mixing valve control Line no. Operating line 2130 2132 2133 2134 2135 2136 Mixing valve boost Actuatortype Switching differential 2-pos Actuator running time Mixing valve Xp Mixing valve Tn Mixing valve boost For mixing, the actual value of the boiler flow temperature must be higher than the required setpoint of the mixing valve flow temperature since otherwise that temperature cannot be controlled. The controller generates the boiler temperature setpoint based on the increase set here and the current flow temperature setpoint. Actuator:type Selection of the type of actuator determines the way the control action impacts the type of mixing valve actuator used. Switching differential 2pos For the 2-position actuator, the 2-position switching differential must also be adapted. This is not required when using 3-position actuators. Actuator: running time Setting the actuator running time for the mixing valve used. Mixing valve Xp The proportional band defines within which change of the control variable ∆x (∆T of the flow) the whole correcting span y (valve travel) is traversed. The smaller the proportional band, the greater the change of the manipulated variable ∆y at a given change of the controlled variable ∆x. Mixing valve Tn The integral action time is the period of time the controller’s I-part would require to produce the same change of the manipulated variable as the P-part An adjustment of the integral action time changes the valve’s rate of response. The longer the integral action time Tn, the slower the response of the controlled system. 2392Z08 y 1 Xp t Tn x t 18/26 Siemens Schweiz AG HVAC Products User Manual OEM The settings in detail CE1U2353en01a 22. November 2006 @ 2.6 DHW storage tank Release Line no. Operating line 5010 Charging Once / day Several times / day Charging Selection of charging “Once/day“ or “Several times/day” is active only if DHW release is set according to the time programs of the heating circuits. Once / day Release of DHW charging is given 2.5 hours before the first heat request fom the heating circuit is received. Then, the reduced DHW setpoint applies for the whole day. Heizprogramm Time program Einmal Once perpro day Tag DHW release TWW-Freigabe 2.5h In the case of continuous heating (with no setback periods), release of DHW charging is given at 0:00. The same rule also applies if the first request for heat from the heating circuit is received before 02:30. If a request for heat is delivered at midnight, DHW charging is released after the first setback period, but no earlier than 2.5 hours before midnight. Day Tag11 Day Tag2 2 Day 33 Tag Day Tag4 4 Time program Heizprogramm DHW release TWW-Freigabe 2.5h 0:00 24:00 2.5h 2.5h 22:00 2.5h Several times / day When selecting “Several times/day“, release of DHW charging is put forward in time by 1 hour against the periods of time the heating circuit calls for heat, and is then maintained during these periods of time. Heizprogramm Time program Several times perTag Mehrmals pro day DHW release TWW-Freigabe 1h 1h Charging control Switching diff Line no. Operating line 5024 Switching diff If the DHW temperature is lower than the current setpoint minus the switching differential set here, DHW charging will be started. DHW charging will be terminated when the temperature reaches the current setpoint. 19/26 Siemens Schweiz AG HVAC Products User Manual OEM The settings in detail CE1U2353en01a 22. November 2006 When DHW heating is released for the first time in a 24-hour period, forced charging will be initiated. DHW charging is also started when the DHW temperature lies within the switching differential, provided it does not lie less than 1 K below the setpoint. Charging time limitation Charging time limitation Line no. Operating line 5030 Charging time limitation During DHW charging, space heating may obtain no or too little energy, depending on the selected charging priority (operating line 1630) and the type of hydraulic circuit. For this reason, it is often practical to set a time limit to DHW charging. --Charging time limitation is deactivated. The DHW is heated up to the nominal setpoint, even if space heating temporarily obtains too little heat. 10 – 600 DHW charging is stopped after the set period of time in minutes and then locked for the same time before it is resumed. During this period of time, the heat produced by the boiler is made available for space heating. This cycle is repeated until the nominal DHW setpoint is reached. When space heating is switched off (summer operation, Eco function, etc.), DHW charging will not be stopped, independent of the selected setting. Discharging protection Discharging protection Line no. Operating line 5040 Discharging protection This function ensures that the DHW charging pump (Q3) will be activated only when the boiler temperature is sufficiently high. • With sensor The charging pump will be activated only when the boiler temperature reaches the level of the DHW temperature plus half the charging boost. If, during charging, the boiler temperature drops to a level below the DHW temperature plus 1/8 the charging boost, the charging pump will be deactivated again. If 2 DHW sensors are parameterized for DHW charging, the lower temperature is used for the discharging protection function (usually sensor B31). • With thermostat The charging pump will be activated only when the boiler temperature lies above the nominal DHW setpoint. If, during charging, the boiler temperature drops below the nominal DHW temperature minus the DHW switching differential, the charging pump will be deactivated again. Off Function is deactivated. Always The function is always active. Automatic The function is active only if the heat source is unable to deliver heat, or is not available (fault, heat generation lock). 20/26 Siemens Schweiz AG HVAC Products User Manual OEM The settings in detail CE1U2353en01a 22. November 2006 Overtemperature protection Storage tank temp max Line no. Operating line 5051 Storage tank temp max If the storage tank reaches the maximum storage tank temperature set here, the collector pump will be deactivated. It will be released again when the storage tank temperature drops 1 °C below the maximum storage tank temperature. The protective collector overtemperature function can reactivate the collector pump until the storage tank’ s safety temperature is reached. T TSpMax TSp L 2354Z10 1°C 1 0 t TSpMax TSp L Storage tank temp max (operating line 5051) Actual value of the storage tank temperature Storage tank charging: 1 = on, 0 = off DHW push Line no. Operating line 5070 Automatic push Off On Automatic push The DHW push can be triggered either manually or automatically. With the DHW push, the DHW is heated up once until the nominal setpoint is reached. Off The DHW push must be triggered manually. On If the DHW temperature falls below the reduced setpoint (operating line 1612) by at least 2 switching differentials (operating line 5024), one-time charging to the nominal DHW setpoint (operating line 1610) will take place again. The automatic DHW push only works when the DHW operating mode is activated. 2.7 Configuration Building and room model Gradient room model Line no. Operating line 6112 Gradient room model The room model gradient gives the period of time in minutes room heating needs to raise the temperature by 1 °C. The setting made applies to all circuits. 21/26 Siemens Schweiz AG HVAC Products User Manual OEM The settings in detail CE1U2353en01a 22. November 2006 The setting is used to calculate the fictive room temperature of rooms that have no room temperature sensor installed (operating lines 8742, 8772, and 8802). Parameters Line no. Operating line 6204 Save parameters . The current parameter settings can be saved as new standard settings. Exempted from this are the following operating pages: Time of day and date, operator section, wireless, and all time programs, as well as the number of operating hours and the different counters. Important: With this process, the factory settings will be overwritten and can no longer be retrieved! Device hours run Line no. Operating line 6222 Device hours run This indicates the total number of operating hours since the controller was first commissioned. 2.8 LPB Error / maintenance / alarms Line no. Operating line 6610 6612 6620 Display system messages Alarm delay Action changeover functions Segment System Display system messages This setting enables system messages transmitted via LPB to be suppressed at the connected operator unit. Alarm delay Delivery of the alarm to the OCI can be delayed in the basic unit by setting a delay. This ensures that unnecessary notifications of a service center resulting from short-time errors (e.g. temperature limiter cut out, communication error) can be prevented. It is to be noted, however, that errors occurring for a short period of time, and reoccurring constantly and rapidly, will also be filtered. Range of action of changeover The range of action of central changeover can be defined. This applies to the following types of limitation: • Optg mode changeover • Summer changeover (when selecting ”Central“ on setting line 6621) Entries: • Segment: Changeover takes place with all controllers in the same segment. • System: Changeover takes place with all controllers in the entire system (in all segments). The controller must be located in segment 0! 22/26 Siemens Schweiz AG HVAC Products User Manual OEM The settings in detail CE1U2353en01a 22. November 2006 2.9 Error History 1...10 Line no. Operating line 6820 Reset history No Yes Reset history The error history with the last 10 errors will be deleted. 2.10 Diagnostics consumers Heating circuit 1, heating circuit 2, heating circuit P Room temperature 1 / 2 / P model Line no. Operating line 8742 8772 8802 Room temp 1 model Room temp 2 model Room temp P model The room model calculates a fictive room temperature for rooms that have no room temperature sensor. The value calculated for each heating circuit is indicated on these operating lines. This allows boost heating, quick setback and optimum start and stop control to be implemented with no need for using a room temperature sensor. The calculation takes into account the attenuated outside temperature (operating line 8703), the room model gradient (operating line 6112) for switching to a higher setpoint, and the building’s time constant (operating line 6110) for switching to a lower setpoint. 23/26 Siemens Schweiz AG HVAC Products User Manual OEM The settings in detail CE1U2353en01a 22. November 2006 Index A action changeover functions......................................22 attenuated outside temperature ................................23 Automatic push..........................................................21 B building’s time constant .............................................23 C charging DHW ...........................................................19 Charging time limitation.............................................20 copy settings .............................................................15 D Data:read...................................................................15 Data:write ..................................................................15 Device hours run .......................................................22 DHW charging ...........................................................19 DHW push .................................................................21 DHW switching differential ........................................19 E error reset..................................................................23 F flow temp setpoint max..............................................17 flow temp setpoint min...............................................17 G Gradient room model...........................................21, 23 H history reset...............................................................23 hours run device........................................................22 I integral action time ..............................................16, 18 L limitation of charging time......................................... 20 M maximum nominal setpoint....................................... 16 model room temperature 1 / 2 / P............................. 23 N Nominal setpoint max ............................................... 16 O once / day ................................................................. 19 Optimum start control ............................................... 23 optimum stop control ................................................ 23 P proportional band................................................ 15, 18 push.......................................................................... 21 Q quick setback / boost heating ................................... 23 R reset error history ......................................................... 23 room model gradient................................................. 21 room temperature model 1 / 2 / P............................. 23 S Save parameters ...................................................... 22 Saving parameter settings........................................ 22 several times / day.................................................... 19 Summer changeover ................................................ 22 switching differential DHW........................................ 19 24/26 Siemens Schweiz AG HVAC Products Benutzerhandbuch 2 The settings in detail CE1U2354de01a 22. November 2006 3 Proof of change All changes since the last issue (see front side) are registered in the original document (Winwordfile) with the Winwordfunktion " Highlight ". To make these passages visible, go forward with the following key combination: Show: Ctrl+Shift+?’ Hide: Ctrl+Shift+` Or put the same functionality about the following Winword menu: Menu: [Tools] - [Optionen] Option: [Highlight] In the Printfile (PDF) the change proof is not evident.’ 25/26 Siemens Schweiz AG HVAC Products User Manual OEM CE1U2353en01a 22. November 2006 Siemens Schweiz AG Siemens Switzerland Ltd Building Technologies Group / HVAC Products Gubelstrasse 22 CH -6301 Zug Tel. +41 41-724 24 24 Fax +41 41-724 35 22 www.sbt.siemens.com © 2005-2006 Siemens Building Technologies AG Subject to alteration 26/26 Siemens Schweiz AG HVAC Products User Manual OEM 3 Proof of change CE1U2353en01a 22. November 2006
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 26 Signing Authority : Schaub Thomas Signing Date : 2006:11:22 14:44:15+01:00 Signing Reason : I am the author of this document Modification Permissions : Fill forms, Create page templates, Sign Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-14, framework 1.6 About : uuid:936d01f9-4be7-4df7-8d17-a72413b6163a Producer : Acrobat Distiller 6.0.1 (Windows) Create Date : 2006:11:22 14:19:30+01:00 Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2006:11:23 15:17:38+01:00 Metadata Date : 2006:11:23 15:17:38+01:00 Document ID : uuid:0904b819-78d4-4678-a1d4-8321ba238951 Format : application/pdf Creator : schaubt Title : Microsoft Word - 012_Albatros2_U2353en_01a.doc Author : schaubtEXIF Metadata provided by EXIF.tools