Sierra Wireless MC8705 GSM/GPRS/EDGE/WCDMA/HSDPA/HSUPA/HSPA+Module User Manual HW Integration Guide

Download:
Mirror Download [FCC.gov]
Document ID	1385014
Application ID	Tv0UnH/XA5vCEneTbx7CZQ==
Document Description	Hdw Integration Guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	33.62kB (420310 bits)
Date Submitted	2010-12-02 00:00:00
Date Available	2011-05-28 00:00:00
Creation Date	2017-11-07 05:38:40
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-11-07 05:38:40
Document Title	HW Integration Guide.book
Document Creator	FrameMaker 8.0

AirPrime Intelligent Embedded
Modules
Hardware Integration Guide
2130114
Rev 2.02
Preface
Important
Notice
Due to the nature of wireless communications, transmission and reception of data
can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be
totally lost. Although significant delays or losses of data are rare when wireless
devices such as the Sierra Wireless modem are used in a normal manner with a
well-constructed network, the Sierra Wireless modem should not be used in
situations where failure to transmit or receive data could result in damage of any
kind to the user or any other party, including but not limited to personal injury,
death, or loss of property. Sierra Wireless accepts no responsibility for damages
of any kind resulting from delays or errors in data transmitted or received using
the Sierra Wireless modem, or for failure of the Sierra Wireless modem to
transmit or receive such data.
Safety and
Hazards
Do not operate the Sierra Wireless modem in areas where blasting is in progress,
where explosive atmospheres may be present, near medical equipment, near life
support equipment, or any equipment which may be susceptible to any form of
radio interference. In such areas, the Sierra Wireless modem MUST BE
POWERED OFF. The Sierra Wireless modem can transmit signals that could
interfere with this equipment.
Do not operate the Sierra Wireless modem in any aircraft, whether the aircraft is
on the ground or in flight. In aircraft, the Sierra Wireless modem MUST BE
POWERED OFF. When operating, the Sierra Wireless modem can transmit
signals that could interfere with various onboard systems.
Note: Some airlines may permit the use of cellular phones while the aircraft is on the
ground and the door is open. Sierra Wireless modems may be used at this time.
The driver or operator of any vehicle should not operate the Sierra Wireless
modem while in control of a vehicle. Doing so will detract from the driver or
operator's control and operation of that vehicle. In some states and provinces,
operating such communications devices while in control of a vehicle is an offence.
Limitation of
Liability
The information in this manual is subject to change without notice and does not
represent a commitment on the part of Sierra Wireless. SIERRA WIRELESS AND
ITS AFFILIATES SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL
DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL,
PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT NOT LIMITED TO,
LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE
ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS
PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE
FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY.
Notwithstanding the foregoing, in no event shall Sierra Wireless and/or its
affiliates aggregate liability arising under or in connection with the Sierra Wireless
product, regardless of the number of events, occurrences, or claims giving rise to
liability, be in excess of the price paid by the purchaser for the Sierra Wireless
product.
Rev 2.02 Sep.10
Proprietary and Confidential
AirPrime Embedded Module Hardware Integration Guide
Patents
This product includes technology licensed from QUALCOMM® 3G.
Manufactured or sold by Sierra Wireless Inc. or its licensees under one or more
patents licensed from InterDigital Group.
Copyright
©2010 Sierra Wireless. All rights reserved.
Trademarks
AirCard® and Watcher® are registered trademarks of Sierra Wireless. Sierra
Wireless, AirPrime, AirLink, AirVantage and the Sierra Wireless logo are
trademarks of Sierra Wireless.
Windows® and Windows Vista® are registered trademarks of Microsoft
Corporation.
Macintosh® and Mac OS® are registered trademarks of Apple Inc., registered in
the U.S. and other countries.
QUALCOMM® is a registered trademark of QUALCOMM Incorporated. Used
under license.
Other trademarks are the property of their respective owners.
Contact
Information
Sales Desk:
Phone:
1-604-232-1488
Hours:
8:00 AM to 5:00 PM Pacific Time
E-mail:
sales@sierrawireless.com
Post:
Sierra Wireless
13811 Wireless Way
Richmond, BC
Canada
V6V 3A4
Fax:
1-604-231-1109
Web:
www.sierrawireless.com
Consult our website for up-to-date product descriptions, documentation,
application notes, firmware upgrades, troubleshooting tips, and press releases:
www.sierrawireless.com
Revision
History
Revision
number
Release date
Changes
2.02
September 2010
•
Created document
Proprietary and Confidential
2130114
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
The Universal Development Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Required connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Guide organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Related documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Power Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Overview of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Power signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Electrostatic discharge (ESD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Module power states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Disconnected state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Off state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Normal state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Low power state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Usage models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
RF Integration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
RF connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Ground connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Shielding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Antenna and cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Interference and sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Power supply noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Interference from other wireless devices . . . . . . . . . . . . . . . . . . . . . . . . . 19
Device-generated RF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Important notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Safety and hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Rev 2.02 Sep.10
Proprietary and Confidential
AirPrime Embedded Module Hardware Integration Guide
Important compliance information for North American users. . . . . . . . . . . . 22
EU regulatory conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Brazil ANATEL homologation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Acronyms and Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Proprietary and Confidential
2130114
1
1: Introduction
Sierra Wireless’ AirPrime Intelligent Embedded Modules form the
radio component for the products in which they are embedded.
Table 1-1 identifies embedded modules that are available for use on
CDMA and GSM networks.
Table 1-1: CDMA and UMTS AirPrime Intelligent Embedded Modules
GPS features
Device
Networks
Network
standards
MC5727
CDMA
MC5727V
MC5728V
CDMA IS-95
1X
1xEV-DO (IS856)
MC8201
GSM
GSM, GPRS,
EDGE, UMTS,
HSDPA
CDMA
CDMA 1xRTT,
EV-DO Rev.A
GSM
GSM, GPRS,
EDGE, UMTS,
HSDPA,
HSUPA,
HSPA+
MC8700
GSM
GSM, GPRS,
EDGE, UMTS,
HSDPA,
HSUPA,
HSPA+
MC8704
MC8705
MC8801
GSM
Standalone
gpsOne


gpsOne
XTRA
A-GPS
Nav2.0
NMEA
sentences






GSM, GPRS,
EDGE, UMTS,
HSDPA,
HSUPA,
HSPA+




 (5)
MC8775
GSM
MC8775V
GSM, GPRS,
EDGE, UMTS,
HSDPA

MC8780
GSM
MC8781
MC8790
MC8790V
MC8791V
MC8792V
MC8795V
GSM, GPRS,
EDGE, UMTS,
HSDPA,
HSUPA




 (5)
MC8355
Rev 2.02 Sep.10
Proprietary and Confidential
AirPrime Embedded Module Hardware Integration Guide
Note: An understanding of
network technology, and
experience in integrating
hardware components into
electronic equipment is
assumed.
Purpose of this guide
This guide addresses issues that affect the integration of AirPrime embedded
modules into host products, and includes design recommendations for the host
products.
The Universal Development Kit
Sierra Wireless manufactures a Universal Development Kit (UDK) that facilitates
all phases of the integration process.
This kit is a hardware development platform that is designed to support the
AirPrime embedded modules listed in Table 1-1 on page 7. It contains the
hardware components that are typically necessary for evaluating and developing
with the module, including:
•
Development board
•
Cables
•
Antennas
•
Other accessories
For instructions on setting up the UDK, see PCI Express Mini Card Dev Kit Quick
Start Guide (Document 2130705).
Required connectors
Note: Contact vendors
before choosing your
connectors—the numbers
included here are for
reference only. Choose
connectors that are appropriate to your design.
When integrating AirPrime embedded modules into your host device, you need
the following connector types:
•
RF cables that mate with Hirose U.FL connectors (model
U.FL #CL331-0471-0-10). Modules include one to three connector jacks
depending on individual module support for diversity or GPS functionality.
•
Industry-standard mating connector for 52-pin EDGE—some manufacturers
include Tyco, Foxconn, and Molex. For example, the connector used on the
Mini Card Dev Kit board is a Molex 67910-0001.
•
Industry-standard USIM connector (MC8xxx only)—the actual connector you
use depends on how your device exposes the USIM socket. For example, the
USIM connector used on the Mini Card Dev Kit board is an ITT CCM03-3518.
Guide organization
This guide includes the following sections:
1. Introduction (this section)
2. Power Interface on page 13
Describes power control signals used by the module and discusses design
issues related to power supply integration.
3. RF Integration on page 17
Describes antenna connection methods and grounding issues, RF interference and desense issues.
Proprietary and Confidential
2130114
Introduction
4. Host/Module Interfaces on page 21
Describes the USB interface for host/module communication, and the USIM
interface for host/module integration.
5. Regulatory Information on page 21
Describes regulatory approvals and regulatory information requirements.
6. Acronyms and Definitions on page 25
Lists acronyms and definitions used throughout this guide.
7. Index on page 27
Note: The term "host" always refers to the host device.
Related documents
This guide deals specifically with hardware integration issues that are unique to
AirPrime embedded modules.
Table 1-2 lists other documents referenced in this guide.
Table 1-2: Related documentation
Document title
Description
AT Command Set for User Equipment (UE)
(Release 6) (3GPP TS 27.007)
Standard AT commands for GSM/UMTS devices.
CDMA 1X Standard
(CDMA 200 Series Release A (2000) Document #TIA/EIA/IS-2000 Series,
Release A)
Technical requirements for CDMA systems, including details on sleep
cycle index (SCI) values.
CDMA CnS Reference (Document 2130754)
CnS (Control and Status) messages supported by AirPrime CDMA
embedded modules.
CDMA AT Command Reference (Document
2130620)
Proprietary, basic AT commands for AirPrime CDMA embedded
modules.
For UMTS-specific commands, see AirCard/AirPrime UMTS devices
Supported AT Command Reference (Document 2130617).
CDMA Extended AT Command Reference
(Document 2130621)
Proprietary AT commands for AirPrime CDMA embedded modules.
For UMTS-specific commands, see AirPrime MC8xxx Embedded
Modules Extended AT Command Reference (Document 2130616).
FCC Regulations - Part 15 - Radio Frequency
Devices
This section of the FCC Code of Federal Regulations, Title 47 deals with
radio frequency devices, including shielding requirements for embedded
modules.
IEC-61000-4-2 level 3
Techniques for testing and measuring electrostatic discharge (ESD)
immunity.
MC5727 Mini Card Product Specification
(Document 2130958)
Features, mechanical and electrical specifications, and standards
compliance of the MC5727.
MC5727V Mini Card Product Specification
(Document 2131023)
Features, mechanical and electrical specifications, and standards
compliance of the MC5727V.
Rev 2.02 Sep.10
Proprietary and Confidential
AirPrime Embedded Module Hardware Integration Guide
Table 1-2: Related documentation (Continued)
Document title
Description
MC5728V Mini Card Product Specification
(Document 2111350)
Features, mechanical and electrical specifications, and standards
compliance of the MC5728V.
MC8201 PCI Express Mini Card Product
Specification (Document 2131362)
Features, mechanical and electrical specifications, and standards
compliance of the MC8201.
MC8700 PCI Express Mini Card Product
Specification (Document 2131202)
Features, mechanical and electrical specifications, and standards
compliance of the MC8700.
AirPrime MC8704 with Audio PCI Express
Mini Card Product Specification (Document
2400059)
Features, mechanical and electrical specifications, and standards
compliance of the MC8704.
AirPrime MC8705 PCI Express Mini Card
Product Specification (Document 2400057)
Features, mechanical and electrical specifications, and standards
compliance of the MC8705.
MC8775 PCI Express Mini Card Product
Specification (Document 2130697)
Features, mechanical and electrical specifications, and standards
compliance of the MC8775.
MC8775V with Audio PCI Express Mini Card
Product Specification (Document 2130700)
Features, mechanical and electrical specifications, and standards
compliance of the MC8775V.
MC8780 / MC8781 PCI Express Mini Card
Product Specification (Document 2130782)
Features, mechanical and electrical specifications, and standards
compliance of the MC8780/MC8781.
MC8790 PCI Express Mini Card Product
Specification (Document 2111279)
Features, mechanical and electrical specifications, and standards
compliance of the MC8790.
MC8790V PCI Express Mini Card Product
Specification (Document 2111280)
Features, mechanical and electrical specifications, and standards
compliance of the MC8790V.
MC8791V PCI Express Mini Card Product
Specification (Document 2131032)
Features, mechanical and electrical specifications, and standards
compliance of the MC8791V.
MC8792V PCI Express Mini Card Product
Specification (Document 2131033)
Features, mechanical and electrical specifications, and standards
compliance of the MC8792V.
MC8795V PCI Express Mini Card Product
Specification (Document 2131276)
Features, mechanical and electrical specifications, and standards
compliance of the MC8795V.
MC87XX Modem CnS Reference (Document
2130602)
CnS (Control and Status) messages supported by AirPrime UMTS
embedded modules.
MC87xx Modem CnS Reference (Voice)
(Document 2130817)
Voice-related CnS (Control and Status) messages supported by voiceenabled AirPrime UMTS embedded modules (MC8704, MC8775V,
MC8790V, MC8791V, MC8792V, and MC8795V).
AirPrime MC8801 PCI Express Mini Card
Product Specification (Document 2400068)
Features, mechanical and electrical specifications, and standards
compliance of the MC8801.
AirCard/AirPrime UMTS devices Supported
AT Command Reference (Document
2130617)
Proprietary, basic AT commands for UMTS AirCard and AirPrime
devices. For CDMA-specific commands, see the CDMA AT Command
Reference (Document 2130620).
AirPrime MC8xxx Embedded Modules
Extended AT Command Reference
(Document 2130616)
Proprietary AT commands for UMTS AirPrime embedded modules. For
CDMA-specific commands, see the CDMA Extended AT Command
Reference (Document 2130621).
10
Proprietary and Confidential
2130114
Introduction
Table 1-2: Related documentation (Continued)
Document title
Description
Mobile Station (MS) Conformance
Specification; Part 4: Subscriber Interface
Module (3GPP TS 11.10-4)
SIM testing methods.
PCI Express Mini Card Dev Kit Quick Start
Guide (Document 2130705)
Setup and configuration of modules.
PCI Express Mini Card Electromechanical
Specification Revision 1.1
Universal Serial Bus Specification, Rev 2.0
Rev 2.02 Sep.10
Proprietary and Confidential
11
AirPrime Embedded Module Hardware Integration Guide
12
Proprietary and Confidential
2130114
2
2: Power Interface
Overview of operation
Note: This chapter contains information for both CDMA (MC57xx) and GSM
(MC8xxx) AirPrime embedded modules.
Information that is unique to specific module types is clearly identified.
AirPrime embedded modules are designed to use a 3.3V (nominal)
power supply (3.8V for the MC8201) provided by the host. It is the
host’s responsibility to provide safe and continuous power to the
module at all times; the module does NOT have an independent
power supply, or protection circuits to guard against electrical issues.
The module’s power state is controlled by the host’s assertion/deassertion of the W_Disable# signal. The module also monitors its
supply voltage and requests shutdown if the supply is insufficient.
Power signals
The module must be connected to a 3.3V power supply (3.8V for the
MC8201), as described in PCI Express Mini Card Electromechanical
Specification Revision 1.1.
The MC8xxx has more power pins than the MC57xx due to higher
peak current requirements for GSM devices.
For detailed pinout and voltage/current requirements of these
modules, see the Product Specification Document for your AirPrime
embedded module (see Table 1-2 on page 9).
Electrostatic discharge (ESD)
You are responsible for ensuring that the host has adequate ESD
protection on digital circuits and antenna ports as described by the
following specifications:
Rev 2.02 Sep.10
•
(Operational) RF port (antenna launch and RF connector): IEC61000-4-2—Level (Electrostatic Discharge Immunity Test)
•
(Non-operational) Host connector interface: JESD22-A114-B +/1kV Human Body Model and JESD22-C101 +/- 125 V Charged
Device Model
•
MC5728V only: (Non-operational) Host connector interface:
JESD22-A114-B +/- 125V Human Body Model and
JESD22-C101 +/- 100 V Charged Device Model
MC5728V has placeholders for additional ESD devices, for
cases where the device must, per customer requirements, meet
the higher Human Body Model (+/-1kV) ESD rating.
Proprietary and Confidential
13
AirPrime Embedded Module Hardware Integration Guide
This guide provides specific recommendations where needed, however, the level
of protection required depends on your application.
Note: ESD protection is highly recommended for the USIM connector at the point where
the contacts are exposed, and for any other signals from the host interface that would be
subjected to ESD by the user of the product.
Module power states
Note: The module unit
defaults to the Normal
state when VCC is first
applied in the absence of
W_Disable# control.
The module has four power states:
•
Disconnected
No power to the module.
•
Off
Power to the module, but the module is powered off.
•
Normal
The module is active. Several modes are possible (Receive, Transmit, Sleep,
Shutdown).
•
Low power (“airplane mode”)
The module is active, but RF is disabled.
State machines are implemented in the module to monitor the power supply and
operating temperature.
Disconnected state
Note: The difference
between the Disconnected and Off states is
that, in the Off state, the
module is still connected to
the power source and
draws minimal current.
This state occurs when there is no power to the module—the host power source
is disconnected from the module and all voltages associated with the module are
at 0 V.
Whether the host device is also powered off depends on the power rail design:
•
If the connection between the power rail and the module is controlled by the
host, the host can stay powered on and cut the power to put the module into
the disconnected state.
•
If the power rail is shared between the host device and the module, the host
is powered off when the module is powered off.
Off state
In this state, the host is powered up and the module is powered down (but still
connected to the power source).
The host keeps the module powered off by driving the W_Disable# signal low. In
this state, the module draws minimal current.
14
Proprietary and Confidential
2130114
Power Interface
Note: This is the default
state when VCC is first
applied in the absence of
W_Disable# control.
Normal state
This is the active state of the module. In this state:
•
The module is fully powered.
•
The module is capable of placing/receiving calls or establishing data connections on the wireless network.
•
The USB interface is fully active.
Low power state
In this state (also called “airplane mode”), RF (both Rx and Tx) is disabled in the
module, but the USB interface is still active.
Usage models
Usage models can be used to calculate expected current consumption. A sample
usage model is provided in Table 2-1,
Table 2-1: Power consumption of sample application
Used by a field
worker (data only)
Used for remote
data logging
Upload (module Tx)
1000 kB/day
40 kB/h
Download (module Rx)
500 kB/day
100 kB/day
Coverage/data rate
1X/80 kbps
IS-95/14.4 kbps
Hours of operation
8 hrs/day (off 16 hrs/day)
24/day
60 mAh
200 mAh
Total power consumed
over 24 hours
This example model applies to a battery-operated device. In practice, because
the module is isolated from the battery (the host device manages the power
source), the mAh ratings depend on the module’s supply efficiency.
The module automatically enters slotted sleep mode when there is no
transmission or reception occurring (SCI = 2).
Transmit power is assumed to be +3 dBm.
Rev 2.02 Sep.10
Proprietary and Confidential
15
AirPrime Embedded Module Hardware Integration Guide
16
Proprietary and Confidential
2130114
3
3: RF Integration
AirPrime embedded modules operate on the following frequencies:.
Table 3-1: RF Parameters (AirPrime UMTS embedded modules)
Frequencies
(MHz)
AirPrime UMTS embedded module (MC8xxx)
8201
8355
8700
8704
8705
8775
8775V
8777V
8780
8781
8790
9890V
8791V
8792V
8795V
8801
GSM 850
Tx: 824–849
Rx: 869–894
















EGSM_900 a
Tx: 880–915
Rx: 925–960
















DCS 1800 a
Tx: 1710–1785
Rx: 1805–1880
















PCS 1900 a
Tx: 1850–1910
Rx: 1930–1990
















Band I b
(UMTS 2100)
Tx: 1920–1980
Rx: 2110–2170
















Band II b
(UMTS 1900)
Tx: 1850–1910
Rx: 1930–1990
















Band V b,c
(UMTS 850)
Tx: 824–849
Rx: 869–894
















Band VIII b
(UMTS 900)
Tx: 880–915
Rx: 925–960




























CDMA2000 BC0
Tx: 824–849
Rx: 869–894

CDMA2000 BC1
Tx: 1850–1910
Rx: 1930–1990

CDMA2000 BC6
Tx: 1920–1980
Rx: 2110–2170

GPS
1575.42


a. (2%) CS
b. (0.1%) 12.2 kbps
c. Band VI is included as a subset of Band V.
Rev 2.02 Sep.10
Proprietary and Confidential
17
AirPrime Embedded Module Hardware Integration Guide
RF connection
When attaching an antenna to the module:
Note: To disconnect the
antenna, make sure you
use the Hirose U.FL
connector removal tool
(P/N UFL-LP-N-2(01)) to
prevent damage to the
module or coaxial cable
assembly.
•
Use a Hirose U.FL connector (model U.FL #CL331-0471-0-10) to attach an
antenna to a connection point on the module.
•
Match coaxial connections between the module and the antenna to 50 
•
Minimize RF cable losses to the antenna; the recommended maximum cable
loss for antenna cabling is 0.5 dB.
Ground connection
When connecting the module to system ground:
•
Prevent noise leakage by establishing a very good ground connection to the
module through the host connector.
•
Connect to system ground using the two mounting holes at the top of the
module.
•
Minimize ground noise leakage into the RF.
Depending on the host board design, noise could potentially be coupled to
the module from the host board. This is mainly an issue for host designs that
have signals traveling along the length of the module, or circuitry operating at
both ends of the module interconnects.
Shielding
The module is fully shielded to protect against EMI and to ensure compliance with
FCC Part 15 - “Radio Frequency Devices” (or equivalent regulations in other
jurisdictions).
Note: The module shields must NOT be removed.
Note: Values in this guide
are taken from the appropriate product specification documents (PSDs)
(listed in Related
documents on page 9)—in
the case of a discrepancy
between this document
and the relevant PSD, use
the value listed in the PSD.
18
Antenna and cabling
When selecting the antenna and cable, it is critical to RF performance to match
antenna gain and cable loss.
Choosing the correct antenna and cabling
Consider the following points for proper matching of antennas and cabling:
•
The antenna (and associated circuitry) should have a nominal impedance of
50  with a return loss of better than 10 dB across each frequency band of
operation.
•
The system gain value affects both radiated power and regulatory (FCC, IC,
CE, etc.) test results.
Proprietary and Confidential
2130114
RF Integration
Developing custom antennas
Consider the following points when developing custom-designed antennas:
•
A skilled RF engineer should do the development to ensure that the RF
performance is maintained.
•
Identify the bands that need to be supported.
Determining the antenna’s location
Consider the following points when deciding where to put the antenna:
Note: These modules are
based on ZIF (Zero Intermediate Frequency)
technologies. When
performing EMC (Electromagnetic Compatibility)
tests, there are no IF
(Intermediate Frequency)
components from the
module to consider.
•
Antenna location may affect RF performance. Although the module is
shielded to prevent interference in most applications, the placement of the
antenna is still very important—if the host device is insufficiently shielded,
high levels of broadband or spurious noise can degrade the module’s performance.
•
Connecting cables between the module and the antenna must have 50 
impedance. If the impedance of the module is mismatched, RF performance
is reduced significantly.
•
Antenna cables should be routed, if possible, away from noise sources
(switching power supplies, LCD assemblies, etc.). If the cables are near the
noise sources, the noise may be coupled into the RF cable and into the
antenna.
Interference and sensitivity
Several sources of interference can affect the RF performance of the module
(RF desense). Common sources include power supply noise and devicegenerated RF.
RF desense can be addressed through a combination of mitigation techniques
and radiated sensitivity measurement.
Power supply noise
Noise in the power supply can lead to noise in the RF signal.
Note: Values in this guide
are taken from the appropriate product specification documents (PSDs)
(listed in Related
documents on page 9)—in
the case of a discrepancy
between this document
and the relevant PSD, use
the value listed in the PSD.
The power supply ripple limit for the module is no more than 200 mVp-p 1 Hz to
100 kHz. This limit includes voltage ripple due to transmitter burst activity.
Interference from other wireless devices
Wireless devices operating inside the host device can cause interference that
affects the module.
To determine the most suitable locations for antennas on your host device,
evaluate each wireless device’s radio system, considering the following:
•
Rev 2.02 Sep.10
Any harmonics, sub-harmonics, or cross-products of signals generated by
wireless devices that fall in the module’s Rx range may cause spurious
response, resulting in decreased Rx performance.
Proprietary and Confidential
19
AirPrime Embedded Module Hardware Integration Guide
•
The Tx power and corresponding broadband noise of other wireless devices
may overload or increase the noise floor of the module’s receiver, resulting in
Rx desense.
The severity of this interference depends on the closeness of the other antennas
to the module’s antenna. To determine suitable locations for each wireless
device’s antenna, thoroughly evaluate your host device’s design.
Device-generated RF
Note: The module can
cause interference with
other devices such as
hearing aids and on-board
speakers.
All electronic computing devices generate RF interference that can negatively
affect the receive sensitivity of the module.
Wireless devices such as
AirPrime embedded
modules transmit in bursts
(pulse transients) for set
durations (RF burst
frequencies). Hearing aids
and speakers convert
these burst frequencies
into audible frequencies,
resulting in audible noise.
•
Microprocessor and memory
•
Display panel and display drivers
•
Switching-mode power supplies
The proximity of host electronics to the antenna in wireless devices can contribute
to decreased Rx performance. Components that are most likely to cause this
include:
These and other high-speed devices (in particular, the processor) can decrease
Rx performance because they run at frequencies of tens of MHz. The rapid rise
and fall of these clock signals generates higher-order harmonics that often fall
within the operating frequency band of the module, affecting the module’s receive
sensitivity.
Example
On a sub-system running at 40 MHz, the 22nd harmonic falls at 880 MHz, which
is within the cellular receive frequency band.
Note: In practice, there are usually numerous interfering frequencies and harmonics. The
net effect can be a series of desensitized receive channels.
20
Proprietary and Confidential
2130114
A
A: Regulatory Information
Important notice
Because of the nature of wireless communications, transmission and
reception of data can never be guaranteed. Data may be delayed,
corrupted (i.e., have errors) or be totally lost. Although significant
delays or losses of data are rare when wireless devices such as the
Sierra Wireless modem are used in a normal manner with a wellconstructed network, the Sierra Wireless modem should not be used
in situations where failure to transmit or receive data could result in
damage of any kind to the user or any other party, including but not
limited to personal injury, death, or loss of property. Sierra Wireless
and its affiliates accept no responsibility for damages of any kind
resulting from delays or errors in data transmitted or received using
the Sierra Wireless modem, or for failure of the Sierra Wireless
modem to transmit or receive such data.
Safety and hazards
Do not operate your MC57xx/MC8xxx modem:
•
In areas where blasting is in progress
•
Where explosive atmospheres may be present including
refuelling points, fuel depots, and chemical plants
•
Near medical equipment, life support equipment, or any
equipment which may be susceptible to any form of radio interference. In such areas, the MC57xx/MC8xxx modem MUST BE
POWERED OFF. Otherwise, the MC57xx/MC8xxx modem can
transmit signals that could interfere with this equipment.
In an aircraft, the MC57xx/MC8xxx modem MUST BE POWERED
OFF. Otherwise, the MC57xx/MC8xxx modem can transmit signals
that could interfere with various onboard systems and may be
dangerous to the operation of the aircraft or disrupt the cellular
network. Use of a cellular phone in an aircraft is illegal in some
jurisdictions. Failure to observe this instruction may lead to
suspension or denial of cellular telephone services to the offender, or
legal action or both.
Some airlines may permit the use of cellular phones while the aircraft
is on the ground and the door is open. The MC57xx/MC8xxx modem
may be used normally at this time.
Rev 2.02 Sep.10
Proprietary and Confidential
21
AirPrime Embedded Module Hardware Integration Guide
Important compliance information for
North American users
The MC57xx/MC8xxx modem has been granted modular approval for mobile
applications. Integrators may use the MC57xx/MC8xxx modem in their final
products without additional FCC/IC (Industry Canada) certification if they meet
the following conditions. Otherwise, additional FCC/IC approvals must be
obtained.
1. At least 20 cm separation distance between the antenna and the user’s body
must be maintained at all times.
2. To comply with FCC / IC regulations limiting both maximum RF output power
and human exposure to RF radiation, the maximum antenna gain including
cable loss in a mobile-only exposure condition must not exceed 5 dBi in the
cellular band (4 dBi for MC8355) and 4 dBi in the PCS band (3.5 dBi for
MC8355, 3.3 dBi for MC8705).
3. The MC57xx/MC8xxx modem and its antenna must not be co-located or
operating in conjunction with any other transmitter or antenna within a host
device.
4. A label must be affixed to the outside of the end product into which the
MC57xx/MC8xxx modem is incorporated, with a statement similar to the
following:
· For MC5727/MC5727V:
This device contains FCC ID: N7N-MC5727
This equipment contains equipment certified under IC: 2417C-MC5727
· For MC5728V:
This device contains FCC ID: N7N-MC5728
This equipment contains equipment certified under IC: 2417C-MC5728
· For MC8201:
This device contains FCC ID: N7NMC8201
This equipment contains equipment certified under IC: 2417C-MC8201
· For MC8355:
This device contains FCC ID: N7NMC8355
This equipment contains equipment certified under IC: 2417C-MC8355
· For MC8700:
This device contains FCC ID: N7NMC8700
This equipment contains equipment certified under IC: 2417C-MC8700
· For MC8704:
This device contains FCC ID: N7NMC8704
This equipment contains equipment certified under IC: 2417C-MC8704
· For MC8705:
This device contains FCC ID: N7NMC8705
This equipment contains equipment certified under IC: 2417C-MC8705
· For MC8775/MC8775V:
This device contains FCC ID: N7NMC8775
This equipment contains equipment certified under IC: 2417C-MC8775
· For MC8780:
This device contains FCC ID: N7NMC8780
22
Proprietary and Confidential
2130114
Regulatory Information
· For MC8781:
This device contains FCC ID: N7NMC8781
This equipment contains equipment certified under IC: 2417C-MC8781
· For MC8790/MC8790V:
This device contains FCC ID: N7NMC8790
This equipment contains equipment certified under IC: 2417C-MC8790
· For MC8792V:
This device contains FCC ID: N7NMC8792
This equipment contains equipment certified under IC: 2417C-MC8792
· For MC8795V:
This device contains FCC ID: N7NMC8795
This equipment contains equipment certified under IC: 2417C-MC8795
· For MC8801:
This device contains FCC ID: N7NMC8801
This equipment contains equipment certified under IC: 2417C-MC8801
5. A user manual with the end product must clearly indicate the operating
requirements and conditions that must be observed to ensure compliance
with current FCC / IC RF exposure guidelines.
The end product with an embedded MC57xx/MC8xxx modem may also need to
pass the FCC Part 15 unintentional emission testing requirements and be
properly authorized per FCC Part 15.
Note: If this module is intended for use in a portable device, you are responsible
for separate approval to satisfy the SAR requirements of FCC Part 2.1093 and IC
RSS-102.
EU regulatory conformity
Sierra Wireless hereby declares that the MC8700, MC8704, MC8705, MC8775,
MC8775V, MC8780, MC8790, MC8790V, MC8791V, MC8792V, MC8795V, and
MC8801 modems conform with all essential requirements of Directive 1999/5/
EC.
MC8355: TBD
MC8775, MC8775V, MC8780, MC8790, MC8790V, MC8791V, MC8792V:
MC8795V:
MC8700, MC8704, MC8705, MC8801:
The Declaration of Conformity made under Directive 1999/5/EC is available for
viewing at the following location in the EU community:
Sierra Wireless (UK), Limited
Lakeside House
1 Furzeground Way, Stockley Park East
Rev 2.02 Sep.10
Proprietary and Confidential
23
AirPrime Embedded Module Hardware Integration Guide
Uxbridge, Middlesex
UB11 1BD
England
Brazil ANATEL homologation
(MC8790 somente) Este produto está homologado pela ANATEL, de acordo com
os procedimentos regulamentados pela Resolução 242/2000, e atende aos
requisitos técnicos aplicados.
Para maiores informações, consulte o site da ANATEL www.anatel.gov.br.
24
Proprietary and Confidential
2130114
B
B: Acronyms and Definitions
Table B-1: Acronyms and definitions
Acronym or term
Definition
AGC
Automatic Gain Control
BER
Bit Error Rate - a measure of receive sensitivity
BLER
Block Error Rate
Call Box
Base Station Simulator - Agilent E8285A or 8960, Rohde & Schwarz
CMU200
CDMA
Code Division Multiple Access
dB
Decibel = 10 x log10 (P1/P2)
P1 is calculated power; P2 is reference power
Decibel = 20 x log10 (V1/V2)
V1 is calculated voltage, V2 is reference voltage
dBm
Decibels, relative to 1 mW - Decibel(mW) = 10 x log10 (Pwr (mW)/1mW)
DUT
Device Under Test
EDGE
Enhanced Data rates for GSM Evolution
EM
Embedded Module
ESD
ElectroStatic Discharge
FER
Frame Error Rate - a measure of receive sensitivity
GPRS
General Packet Radio Services
GPS
Global Positioning System
GSM
Global System for Mobile communications
Hz
Hertz = 1 cycle/second
inrush current
Peak current drawn when a device is connected or powered on
IS-2000
3G radio standards for voice and data (CDMA only)
IS-95
2G radio standards targeted for voice (cdmaONE)
LDO
Low Drop Out - refers to linear regulator
MC5727/MC5727V/
MC5728V
Sierra Wireless AirPrime embedded modules used on CDMA networks
MC57xx
Any of the following CDMA AirPrime embedded modules: MC5727/
MC5727V/MC5728V
Rev 2.02 Sep.10
Proprietary and Confidential
25
AirPrime Embedded Module Hardware Integration Guide
Table B-1: Acronyms and definitions
Acronym or term
26
Definition
MC8201/MC8700/
MC8704/MC8705/
MC8775/MC8775V /
MC8780/MC8781/
MC8790/MC8790V/
MC8791V/MC8792V/
MC8795V/MC8801
Sierra Wireless AirPrime embedded modules used on GSM/UMTS
networks
MC8xxx
Any of the following GSM/UMTS AirPrime embedded modules: MC8201/
MC8700/MC8704/MC8705/MC8775/MC8775V/MC8780/MC8781/
MC8790/MC8790V/MC8791V/MC8792V/MC8795V/MC8801
MHz
MegaHertz = 10E6 Hertz (Hertz = 1 cycle/second)
MIO
Module Input/Output
MPE
Maximum Permissible Exposure—the level of radiation to which a person
may be exposed without hazardous effect or adverse biological changes
OTA
Over-The-Air or Radiated through the antenna
PCS
Personal Communication System - PCS spans the 1.9 GHz radio spectrum
RF
Radio Frequency
RMS
Root Mean Square
SA
Selective Availability
Sensitivity (Audio)
Measure of lowest power signal that the receiver can measure
Sensitivity (RF)
Measure of lowest power signal at the receiver input that can provide a
prescribed BER/BLER/SNR value at the receiver output.
SIM
Subscriber Identity Module
SNR
Signal to Noise Ratio
SOF
Start of Frame - a USB function
UART
Universal Asynchronous Receiver Transmitter
UDK
Universal Development Kit (PCI Express Mini Card Dev Kit)
UMTS
Universal Mobile Telecommunications System
USB
Universal Serial Bus
USIM
Universal Subscriber Identity Module
VCC
Supply voltage (3.8 V for MC8201, 3.3 V for all others)
WCDMA
Wideband Code Division Multiple Access—In this document, the term
“UMTS” is used instead of “WCDMA”.
XIM
In this document, XIM is used as part of the contact identifiers for the USIM
interface (XIM_VCC, XIM_CLK, etc.).
Proprietary and Confidential
2130114
Index
Numerics
electrostatic discharge. See ESD
ESD
protection requirements, 13– 14
testing techniques document (IEC-61000-4-2), 9
1X
CDMA Standard, 9
acronyms and definitions, 25– 26
antenna
connection considerations, 18
custom, considerations, 19
limit, matching coaxial connections, 18
location, considerations, 19
matching, considerations, 18
maximum cable loss, 18
AT commands
3GPP specification, details, 9
standard, MC57xx (reference document), 9
standard, MC8xxx (reference document), 10
AT commands, extended
MC57xx, reference, 9
MC8xxx, reference, 10
AT commands, standard
MC57xx, reference, 9
MC8xxx, reference, 10
FCC
desense. See RF
disconnected, module power state, 14
Rev 2.02 Sep.10
grounding
connection considerations, 18
impedance
module-antenna, 19
interference
device generated, 20
power supply noise, 19
wireless devices, 19
low power, module power state, 15
cable loss
antenna, maximum, 18
CDMA
1X Standard, 9
CnS
MC57xx reference, 9
MC87xx reference, 10
voice reference, 10
connection
grounding, 18
connectors, required
EDGE mating (52-pin), 8
host-module, 8
RF, Hirose, 8
USIM, 8
current
consumption, usage models, 15
EDGE connector, manufacturers, 8
regulations, relevant section, 9
MC5727
AT reference (extended),
AT reference (standard),
CnS reference, 9
networks supported, 7
product specification, 9
MC5727V
AT reference (extended),
AT reference (standard),
CnS reference, 9
networks supported, 7
product specification, 9
MC5728V
AT reference (extended),
AT reference (standard),
CnS reference, 9
networks supported, 7
product specification, 10
MC8201
networks supported, 7
product specification, 10
MC8355
networks supported, 7
Proprietary and Confidential
27
Document SubTitle
MC8700
AT reference (extended), 10
AT reference (standard), 10
CnS reference, and MC87xx, 10
networks supported, 7
product specification, 10
MC8704
product specification, 10
MC8705
product specification, 10
MC8775
AT reference (extended), 10
AT reference (standard), 10
CnS reference, and MC87xx, 10
networks supported, 7
product specification, 10
MC8775V
AT reference (extended), 10
AT reference (standard), 10
CnS reference, and MC87xx, 10
CnS voice reference, and MC87xxV, 10
networks supported, 7
product specification, 10
MC8780
AT reference (extended), 10
AT reference (standard), 10
CnS reference, and MC87xx, 10
networks supported, 7
product specification, 10
MC8781
AT reference (extended), 10
AT reference (standard), 10
CnS reference, and MC87xx, 10
networks supported, 7
product specification, 10
MC8790
AT reference (extended), 10
AT reference (standard), 10
CnS reference, and MC87xx, 10
networks supported, 7
product specification, 10
MC8790V
AT reference (extended), 10
AT reference (standard), 10
CnS reference, and MC87xx, 10
CnS voice reference, and MC87xxV, 10
networks supported, 7
product specification, 10
MC8791V
AT reference (extended), 10
AT reference (standard), 10
CnS reference, and MC87xx, 10
CnS voice reference, and MC87xxV, 10
networks supported, 7
product specification, 10
28
MC8792V
AT reference (extended), 10
AT reference (standard), 10
CnS reference, and MC87xx, 10
CnS voice reference, and MC87xxV, 10
networks supported, 7
product specification, 10
MC8795V
AT reference (extended), 10
AT reference (standard), 10
CnS reference, and MC87xx, 10
CnS voice reference, and MC87xxV, 10
networks supported, 7
product specification, 10
MC8801
product specification, 10
Mini Card
Dev Kit Quick Start Guide, 11
PCI Express Specification, 11
See also MC5727, MC5727V, MC5728V, MC8201,
MC8700, MC8775, MC8775V, MC8780,
MC8781, MC8790, MC8790V, MC8791V,
MC8792V, MC8795V
module
power states, 14– 15
noise
leakage, minimizing, 18
RF interference, power supply, 19
normal, module power state, 15
off, module power state, 14
PCI Express
Mini Card specification, 11
power
default state, 15
disconnected, characteristics, 14
normal, characteristics, 15
off, characteristics, 14
required supply voltage, 13
signals, overview, 13
state, disconnected, 14
state, low power, 15
state, normal, 15
state, off, 14
states, module, 14– 15
supply, RF interference, 19
supply, ripple limit, 19
power interface, 13– 15
product specification (PSD), 10
PSD (Product Specification Document), 10
Proprietary and Confidential
2130114
Index
regulatory information, 21– 24
Brazil, 24
EU, 23
FCC, 22
limitation of liability, 21
safety and hazards, 21
RF
antenna cable loss, maximum, 18
antenna connection, considerations, 18
cable type, required, 8
desense
device-generated, 20
integration, 17– 20
interference
other devices, 20
power supply, 19
wireless devices, 19
testing
ESD immunity, techniques document (IEC-61000-4-2),
UDK (Universal Development Kit)
components, included, 8
Universal Development Kit (UDK)
components, included, 8
Universal Serial Bus. See USB.
usage models
current consumption, 15
USB
specification, 11
USIM
connector type, required, 8
shielding
module, compliance, 18
SIM
testing methods, MS conformance specification, 11
See also USIM
W_Disable#
Normal state, 15
off state, 14
ZIF (Zero Intermediate Frequency), 19
Rev 2.02 Sep.10
Proprietary and Confidential
29
Document SubTitle
30
Proprietary and Confidential
2130114


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Copy, Extract, Print high-res
Create Date                     : 2010:09:21 08:41:10Z
Modify Date                     : 2010:09:21 08:47:58-07:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Creator                         : 
Title                           : HW Integration Guide.book
Creator Tool                    : FrameMaker 8.0
Metadata Date                   : 2010:09:21 08:47:58-07:00
Producer                        : Acrobat Distiller 9.3.3 (Windows)
Document ID                     : uuid:c2f46e80-fd80-4c8a-9f82-404c69bcaa54
Instance ID                     : uuid:e3024547-8cda-4bba-9025-a8cd2bd71744
Page Mode                       : UseOutlines
Page Count                      : 32

EXIF Metadata provided by EXIF.tools