Silicon Laboratories Finland 0D06E BT 4.0 module User Manual Heading 1

ACKme Networks Inc BT 4.0 module Heading 1

UserManual.wiki >

Silicon Laboratories Finland >

0D06E User Manual

user manual

AMS00x • Embedded Bluetooth Low Energy Solutions ADS-MS00x-100D4 • Preliminary Data Sheet October 22, 2014 ©2014 ACKme Networks. http://ack.me AMS001 AMS002 Data Sheet

ADS-MS00x-100D4 • Preliminary Data Sheet Page | ii ©2014 ACKme Networks. http://ack.me October 22, 2014 AMS00x Family Data Sheet Embedded Bluetooth Low Energy Solution Features  Bluetooth Low Energy (Bluetooth Smart) modules fully certified to meet Bluetooth version 4.1.  Integrated SPI-serial flash supports firmware up-dates and multiple on-board applications  On-board PCB-style antenna  ARM® Cortex™ M3-based microprocessor core  Programmable RF transmit power control  Operation directly from a battery or mains supply  Small size enables integration into most sensor products and applications  Secure Over-the-Air (OTA) software update using industry-standard AES-128 security  On-board Bluetooth Low Energy stack supports multiple Bluetooth Smart Use Cases including Bat-tery status, Blood pressure monitor, Proximity, Thermometer, Glucose meter plus many more  Easily integrated into existing or new products us-ing TruConnect, ACKme’s configurable Bluetooth Low Energy application (pre-installed on every module)  Supports custom application development using the Broadcom WICED Smart Software Develop-ment System. Interfaces*  A/D converter: 8 channels with 4 modes providing variable resolution (10-13 ENOBs), sampling rate (5.9-187 kHz) and conversion latency (5-171 µs)  USART: 2 x 4-wire up to 1.5 Mbit/s  SPI: 1 x master/slave, 1 x slave-only at ≤12 Mbit/s  I2C: 1 x I2C master interface up to 1 MHz  GPIO: Up to 15 GPIOs (overlaid with peripherals), programmable pull-up/pull-down resistors with up to 16 mA drive strength at 3.3V (2 mA standard).  4 x PWM channels each with a 10-bit counter clocked at 128 kHz, 1 MHz or 8 MHz.  Infrared: Modulator and IR learning  Wake-up: Wake from timer, UART or GPIOs for ul-tra-low power operation  Serial-wire Debug interface *Some interfaces share module pins Operational & Radio  Operational voltage : 1.8V - 3.6V  Operational Temperature Range: -30°C to +85°C  Size : 17.6 x 11.4 x 2.3mm (0.70” x 0.45” x 0.09”)  Weight : 0.04 oz (1.2g)  Current consumption @ 3.0V, 25°C - Deep Sleep : 0.65 µA - Sleep : 12 µA - AMS001  Active Receive : 12.8 mA  Active Transmit : 12.1 mA - AMS002  Active Receive : 24.5 mA  Active Transmit : 22.8 mA  RF Transmit Power: +4 dBm  Receive Sensitivity : -94 dBm Applications  Health & Fitness - Fitness Equipment - Heart rate monitors - Weight scales - Thermometers - Pedometers - Glucose meters - Blood pressure monitoring  Retail - Advertising and Beaconing - Proximity detection - Point-of-sale  Home & Industrial Control and Automation - Appliance control and monitoring - Doors/Window monitoring - Alarms - Wireless cable replacement - Environmental & Energy monitoring - Wireless sensing, remote data logging  Consumer - Toys - Robots Remote controls

AMS00x • Embedded Bluetooth Low Energy Solution ADS-MS00x-100D4 • Preliminary Data Sheet Page | iii ©2014 ACKme Networks. http://ack.me October 22, 2014 Contents1 General Description ............................................... 1 2 Block Diagram ........................................................ 2 3 Electrical Specifications .......................................... 3 3.1 Absolute Maximum Ratings ............................ 3 3.2 Recommended Operating Conditions ............ 3 DC Operating Conditions ........................ 3 Environmental Conditions ...................... 3 3.3 Power Consumption ....................................... 4 3.4 ADC Specifications .......................................... 4 4 Bluetooth RF Specifications ................................... 5 4.1 Summary RF Specifications ............................. 5 4.2 Receiver Specifications ................................... 5 4.3 Transmitter Specifications .............................. 6 5 Pinout and Signal Descriptions .............................. 7 5.1 Pinout.............................................................. 7 5.2 Pin Description ................................................ 7 6 Design Guidelines ................................................... 9 6.1 Recommended PCB Footprint ........................ 9 6.2 Routing Recommendations ............................ 9 6.3 Soldering Information ................................... 10 6.4 AMS00x Photograph ..................................... 10 6.5 Application Examples .................................... 10 Operation using TruConnect................. 10 7 Regulatory Certification ....................................... 11 7.1 United States ................................................ 11 Labeling and User Information Requirements ....................................................... 11 RF Exposure .......................................... 12 External Antenna .................................. 12 Further Information .............................. 12 7.2 Canada .......................................................... 12 Labeling and User Information Requirements....................................................... 12 External Antenna Types ........................ 13 Further Information .............................. 13 7.3 Europe .......................................................... 14 Labeling and User Information Requirements....................................................... 14 External Antenna Requirements .......... 14 Further Information .............................. 14 7.4 Australia ........................................................ 16 External Antenna Requirements .......... 16 Further Information .............................. 16 7.5 New Zealand ................................................. 16 External Antenna Requirements .......... 16 Further Information .............................. 16 8 Packaging, Handling & Storage, RoHS ................. 17 8.1 Packaging ...................................................... 17 8.2 Handling & Storage ....................................... 17 8.3 RoHS Directive .............................................. 17 9 Ordering Information ........................................... 18 10 Revision History & Glossary ................................. 19 10.1 Revision History ............................................ 19 10.2 Glossary ........................................................ 19

AMS00x • Embedded Bluetooth Low Energy Solution General Description, Section 1 ADS-MS00x-100D4 • Preliminary Data Sheet Page | 1 ©2014 ACKme Networks. http://ack.me October 22, 2014 1 General Description The family of AMS00x modules from ACKme Networks is based on an ultra-low power Bluetooth Low Energy (Bluetooth Smart) SoC from Broadcom Corporation. All modules incorporate serial-flash memory and a printed antenna to provide a state-of-the-art fully-certified Bluetooth 4.1 solution. An integrated solution avoids difficult RF layout and enables designers to rapidly embed Bluetooth Low En-ergy into virtually any device. Modules ship with ACKme TruConnect, an easy-to-use application enabling control and configuration via a UART-serial interface. TruConnect virtually eliminates difficult and time-consuming software development effort and vastly reduces product development cycles. If required, custom applications may also be developed using the Broadcom WICED Smart Software Develop-ment Kit. With dimensions of just 17.6 x 11.4 mm, a wide tem-perature range, and an ultra-low power version, the module is suitable for integration into any battery-powered embedded wireless application. The Bluetooth Low Energy SoC from Broadcom is pur-pose-designed to support the entire spectrum of Blue-tooth Smart use cases for medical, home automation, accessory, sensor, retail and wearable market seg-ments. Superior receive sensitivity, an integrated RF transmit power amplifier and transmit/receive switch, along with the on-board antenna, provide extended range and full compatibility with all Bluetooth 4.1 de-vices. At the heart of all AMS00x modules is a Bluetooth Low Energy SoC with a high-performance ARM® 32-bit Cor-tex™-M3 core operating at a frequency of 48MHz. The SoC includes is configured to boot applications stored in the 512xkB serial flash memory available on-board the module. Each module provides an extensive array of I/O and peripheral interfaces. The following list of interfaces are available, many of which are accessible with I/O multi-plexing and alternate function capabilities.  8 x A/D converter channels  2 x 4-Wire UART interfaces  1 x SPI master/slave, 1 x SPI slave bus  1 x I2C interface  1 x Infrared Modulator / IR learning input  15 x ultra-low power wake inputs  32kHz crystal interface The module may be powered directly from a battery supply in the range 1.8-3.6V including 2xAAA, 2xAA, or a single Lithium coin cell. Internal power domains are automatically adjusted to minimise power dissipation based on user activity. Var-ious power modes, including an ultra-low power deep sleep mode, are provided to minimize total average power consumption and maximize battery life. The module may be woken from deep sleep mode by various events including a level transition on any GPIO, the UART or an internal timer. An internal 32kHz low-power oscillator is available by default for non-critical timing requirements. Applica-tions requiring an accurate real-time clock may connect an (optional) external 32kHz crystal. Application debugging with a software debugger such as gdb is enabled via a standard Serial Wire Debug in-terface. All versions of the module have Bluetooth BQB SIG cer-tification, and FCC & IC modular approval for use in the United States and Canada, and CE approval for use in Europe and other countries.

AMS00x • Embedded Bluetooth Low Energy Solution Block Diagram, Section 2 ADS-MS00x-100D4 • Preliminary Data Sheet Page | 2 ©2014 ACKme Networks. http://ack.me October 22, 2014 2 Block DiagramFigure 1 is a block diagram showing the architecture of AMS00x Bluetooth Low Energy modules. The major components are a Bluetooth Low Energy SoC from Broadcom Corporation, 24MHz crystal, 512xkbyte serial flash and a PCB-style antenna. The AMS001 version also includes a high-efficiency DC-DC switching regulator to minimize active mode power consumption. The Bluetooth SoC is powered by an ARM Cortex M3-based RISC processor running at 48 MHz with 60 kB RAM. The SoC is driven by a 24 MHz crystal, an on-board real-time clock may be (optionally) enabled by connecting an external 32kHz crystal. The 512 kByte serial flash memory is used to store mul-tiple applications and to enable secure Over-the-Air (OTA) wireless firmware updates. The integrated PCB antenna simplifies RF integration into end products. An extensive array of analog and digital peripherals in-cluding ADCs, GPIOs, PWMs and multiple serial inter-faces such as UART, SPI, I2C and Infrared are accessible via module pins. The module is powered by a single-rail battery or mains supply. Figure 1. AMS00x Architecture VDD 32kHz XTAL ADC SPI UART GPIO I2C IR SWD Reset 512 kByte Serial Flash Bobcat Antenna DC-DC AMS001 Only 24MHz Bluetooth Low Energy SoC ARM Cortex M3

AMS00x • Embedded Bluetooth Low Energy Solution Electrical Specifications, Section 3 ADS-MS00x-100D4 • Preliminary Data Sheet Page | 3 ©2014 ACKme Networks. http://ack.me October 22, 2014 3 Electrical Specifications 3.1 Absolute Maximum Ratings CAUTION! The absolute maximum ratings in Table 1 and Table 2 indicate levels where permanent damage to the de-vice can occur, even if these limits are exceeded for only a brief duration. Functional operation is not guaranteed un-der these conditions. Operation at absolute maximum conditions for extended periods can adversely affect long-term reliability of the device. Table 1. Absolute Maximum Voltage Ratings Symbol Ratings Min. Max. Unit VDDmax DC supply voltage applied to VDD pin GND-0.3 3.8 V Table 2. Absolute Maximum Environmental Ratings Characteristic Note Min. Max. Unit Storage Temperature – -40 +125 °C Relative Humidity Non-condensing (storage) – 65 % 3.2 Recommended Operating Conditions Functional operation is not guaranteed outside the limits shown in Table 3 and Table 4, and operation outside these limits for extended periods can adversely affect long-term reliability of the device. DC Operating Conditions Table 3. Recommended DC Operating Conditions Symbol Ratings1 Min.2 Typical Max. Unit VDD DC supply voltage applied to VDD pin On-board serial flash read-only 1.8 – 3.63 V On-board serial flash read and write 2.2 – 3.63 V Notes: 1. Overall performance degrades beyond minimum and maximum supply voltages. Environmental Conditions Table 4. Recommended Environmental Conditions Characteristic Note Min. Max. Unit Ambient Temperature -30 +85 °C Relative Humidity Non-condensing (operating) – 85 %

AMS00x • Embedded Bluetooth Low Energy Solution Electrical Specifications, Section 3 ADS-MS00x-100D4 • Preliminary Data Sheet Page | 4 ©2014 ACKme Networks. http://ack.me October 22, 2014 3.3 Power Consumption The AMS00x automatically adjusts power dissipation based on user activity to minimize power usage. The power consumption in each state, and for each version of the module, is specified in Table 5. Table 5. Power Consumption (@3.0V, 25°C) Operational State Note Typical Max. Unit Deep sleep Wake on interrupt 0.65 – µA Sleep Wake in <5 ms 12.0 19.2 µA Active Receive1 Receiver is enabled and operating at 100% duty cycle 12.8 13.0 mA Active Transmit1 Transmitter is enabled and operating at 100% duty cycle 12.1 12.3 mA Active Receive2 Receiver is enabled and operating at 100% duty cycle 24.5 25.0 mA Active Transmit2 Transmitter is enabled and operating at 100% duty cycle 22.8 23.3 mA Notes: 1. AMS001 version 2. AMS002 version 3.4 ADC Specifications Table 6. ADC Specifications (@ 25°C) Parameter Symbol Conditions Min. Typ. Max. Unit Input Channels – – 8 – – Channel Switching Rate fch – 133.33 – kch/s Input signal range Vinp 0 – 3.63 V Reference settling time – 7.5 – – µS Input resistance Rin Effective, single ended – 500 – kΩ Input capacitance Cin – – 5 pF Conversion rate Rc 5.859 – 187 kHz Conversion time Tc 5.35 – 170.7 µS Effective Number of Bits ENOB 10 – 13 bits Abs. Voltage Meas. Error – – ±2 – % Current I – – 1 mA Leakage Current Ileakage – – 100 nA Power-up time Tpup – – 200 µS Integral nonlinearity INL LSBs at the 10-bit level -1 – 1 LSB Differential nonlinearity DNL LSBs at the 10-bit level -1 – 1 LSB

AMS00x • Embedded Bluetooth Low Energy Solution Bluetooth RF Specifications, Section 4 ADS-MS00x-100D4 • Preliminary Data Sheet Page | 5 ©2014 ACKme Networks. http://ack.me October 22, 2014 4 Bluetooth RF Specifications Unless otherwise stated, the specifications in this section apply when the operating conditions are within the limits specified in Section 3.2, Recommended Operating Conditions. Functional operation outside these limits is not guar-anteed. All specifications are measured with a coax pigtail soldered to the PCB antenna feed point, with VDD = 3.0V and at a room temperature of 25°C. 4.1 Summary RF Specifications Table 7. Summary RF Specifications Feature Supported Description Bluetooth Standard Version 4.0 Frequency Band 2.402 GHz – 2.480 GHz Channels (2MHz spacing) 3 x Advertising channels @ 2402 / 2426 / 2480 MHz 36 x Data channels Maximum Raw Data Rate 1 Mbit/s Maximum Application Data Rate 0.27 Mbit/s Modulation Type DSSS: GFSK (modulation index = 0.5) Maximum RF Input -10 dBm Typical Receive Sensitivity -94 dBm Maximum RF Tx Output Power +4 dBm Carrier Frequency Accuracy ±20 ppm (24 MHz crystal, ±20 ppm stability @ 25°C) 4.2 Receiver Specifications Table 8. Receiver Performance Specifications Parameter Condition/Notes Min. Typical Max. Unit Frequency Range – 2402 – 2480 MHz Operating Temperature – -30 – +85 °C Receive Sensitivity 200 x 37-byte packets with 30.8% PER – -94 – dBm Maximum Receive Level -10 – – dBm

AMS00x • Embedded Bluetooth Low Energy Solution Bluetooth RF Specifications, Section 4 ADS-MS00x-100D4 • Preliminary Data Sheet Page | 6 ©2014 ACKme Networks. http://ack.me October 22, 2014 4.3 Transmitter Specifications Table 9. Transmitter Performance Specifications Parameter Condition/Notes Min Typical Max Unit Frequency Range – 2402 – 2480 MHz Operating Temperature – -30 – +85 °C Transmit power2 – – 4.0 – dBm Transmit power variation Process dependent – 2.0 – Transmit Power Range Adjustable via software control -20 4 dBm Channel Spacing – 2 – MHz

AMS00x • Embedded Bluetooth Low Energy Solution Pinout and Signal Descriptions, Section 5 ADS-MS00x-100D4 • Preliminary Data Sheet Page | 7 ©2014 ACKme Networks. http://ack.me October 22, 2014 5 Pinout and Signal Descriptions 5.1 Pinout A top view of the AMS00x pinout is depicted in Figure 2. All dimensions are in thousands of an inch. A recom-mended PCB footprint is provided in Section 6.1. Figure 2. AMS00x Pinout (TOP View – Pins NOT visible from top!) 5.2 Pin Description Table 10. AMS00x Pin Definitions Pin Name Type1 Primary Function Alternate & Other Function(s) 1 GND S Ground - 2 UART1_RX I/O UART1 Rx (Debug) - 3 UART1_TX I/O UART1 Tx (Debug) - 4 GPIO_03 I/O SPI1_MOSI I2C_SDA, UART0_CTS, GPIO 5 GPIO_13 I/O SPI1_CLK I2C_SCL, UART0_RTS, GPIO 6 GPIO_2 I/O UART0_TX (User) SPI2_MOSI (M/S), IR_RX, ADC0, GPIO 7 GPIO_3 I/O UART0_RTS (User) SPI2_MISO (M/S), IR_TX, ADC1, GPIO 8 RESET_N I System Reset - 9 GPIO_4 I/O UART0_CTS (User) SPI2_CLK (M/S), GPIO 10 GPIO_5 I/O UART0_RX (User) SPI2_CS (M), SPI2_MOSI (M), GPIO 11 GPIO_6 I/O GPIO UART0_RX, SPI2_MOSI (M/S), IR_TX

AMS00x • Embedded Bluetooth Low Energy Solution Pinout and Signal Descriptions, Section 5 ADS-MS00x-100D4 • Preliminary Data Sheet Page | 8 ©2014 ACKme Networks. http://ack.me October 22, 2014 Pin Name Type1 Primary Function Alternate & Other Function(s) 12 GPIO_7 I/O SPI1_MISO (M) UART0_TX, SPI2_CS (S), ADC2, ACLK0 13 GPIO_8 I/O GPIO UART0_RX, SPI2_MISO (M/S) 14 GPIO_9 I/O GPIO UART0_TX, SPI2_CLK (M/S), SPI1_MISO (M) 15 GPIO_104 I/O GPIO IR_TX, ADC3, PWM3 16 GPIO_11 I/O GPIO SPI2_MOSI (M/S), ADC4, PWM2, IR_TX 17 GPIO_12 I/O GPIO ADC5, IR_RX 18 GPIO_134 I/O XOSC32_OUT SPI2_CS (S), ADC6, PWM0, GPIO 19 GND S Ground - 20 GPIO_144 I/O XOSC32K_IN ADC7, PWM1, GPIO 21 VDD S VDD - 22-27 GND S Ground - Notes: 1. I = Input, O = Output, S = Supply 2. All GPIO pins (except GPIO1, GPIO2) are initialized to ‘input floating’ after Power-on-Reset. 3. The drive strength of standard GPIOs is 2mA, the drive strength of this GPIO is 16mA.

AMS00x • Embedded Bluetooth Low Energy Solution Design Guidelines, Section 6 ADS-MS00x-100D4 • Preliminary Data Sheet Page | 9 ©2014 ACKme Networks. http://ack.me October 22, 2014 6 Design Guidelines 6.1 Recommended PCB Footprint All dimensions in Figure 3 are in thousands of an inch unless otherwise marked. Figure 3. AMS00x Recommended Footprint (Top) 6.2 Routing Recommendations When designing a carrier board, the addition of ground fill directly underneath the module, rather than signal or power traces, is strongly advised. All ground pads adjacent to antenna pins must be connected to a solid ground plane. Failure to comply with these recommen-dations will almost certainly result in degraded perfor-mance of the radio receiver and/or transmitter.

AMS-00x • Embedded Bluetooth Low Energy Solution Regulatory Certification, Section 7 ADS-MS00x-100D4 • Preliminary Data Sheet Page | 11 ©2014 ACKme Networks. http://ack.me October 22, 2014 7 Regulatory Certification The AMS00x family of modules has been certified for operation in various regulatory domains. This section outlines certification information specific to the follow-ing countries and regions:  United States  Canada  Europe  Australia  New Zealand Should you require regulatory certification for the AMS00x module in a country or region not listed, please contact your local ACKme Networks sales office or cre-ate a support request via our website at http://ack.me/contact. 7.1 United States The ACKme Networks AMS-00x module has received Federal Communications Commission (FCC) CFR47 Tele-communications, Part 15 Sub-part C “Intentional Radia-tors” modular approval in accordance with Part 15.212 Modular Transmitter approval. Modular approval al-lows the end user to integrate the AMS-00x module into a finished product without obtaining subsequent and separate FCC approvals for intentional radiation, provided no changes or modifications are made to the module circuitry. Changes or modifications could void the user’s authority to operate the equipment. The end user must comply with all of the instructions provided by the Grantee which indicate installation and/or oper-ating conditions necessary for compliance. The finished product is required to comply with all ap-plicable FCC equipment authorization, regulations, re-quirements, and equipment functions not associated with the transmitter module portion. For example, compliance must be demonstrated to regulations for other transmitter components within the host product; to requirements for unintentional radiators (Part 15 Sub-part B “Unintentional Radiators”), such as digital devices, computer peripherals, radio receivers, etc.; and to additional authorization requirements for non-transmitter functions on the transmitter module (i.e. Verification, or Declaration of Conformity) (e.g., trans-mitter modules may also contain digital logic functions) as appropriate. Labeling and User Information Requirements The AMS-00x module has been labelled with a unique FCC ID number, and if the FCC ID is not visible when the module is installed inside another device, then the out-side of the finished product into which the module is installed must also display a label referring to the en-closed module. This exterior label can use wording as follows: The user manual for the product should include the fol-lowing statement: Contains FCC ID: 2ABPY-BB4EA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause un-desired operation. This equipment has been tested and found to com-ply with the limits for a Class B digital device, pursu-ant to part 15 of the FCC Rules. These limits are de-signed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate ra-dio frequency energy and if not installed and used in accordance with the instructions, may cause harm-ful interference to radio communications. However, there is no guarantee that interference will not oc-cur in a particular installation. If this equipment does cause harmful interference to radio or televi-sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equip-ment and receiver.  Connect the equipment into an outlet on a cir-cuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help.

AMS-00x • Embedded Bluetooth Low Energy Solution Regulatory Certification, Section 7 ADS-MS00x-100D4 • Preliminary Data Sheet Page | 12 ©2014 ACKme Networks. http://ack.me October 22, 2014 Additional information on labeling and user information requirements for Part 15 devices can be found in KDB Publication 784748 available at the FCC Office of Engi-neering and Technology (OET) Laboratory Division Knowledge Database (KDB) at the following website: https://apps.fcc.gov/oetcf/kdb/index.cfm RF Exposure All transmitters regulated by FCC must comply with RF exposure requirements. OET Bulletin 65, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields, provides assis-tance in determining whether proposed or existing transmitting facilities, operations or devices comply with limits for human exposure to Radio Frequency (RF) fields adopted by the Federal Communications Com-mission (FCC). The bulletin offers guidelines and sugges-tions for evaluating compliance. If appropriate, compliance with exposure guidelines for mobile and unlicensed devices can be accomplished by the use of warning labels and by providing users with information concerning minimum separation distances from transmitting structures and proper installation of antennas. The following statement must be included as a CAU-TION statement in manuals and OEM products to alert users of FCC RF exposure compliance: If the AMS-00x module is used in a portable application (i.e., the antenna is less than 20 cm from persons dur-ing operation), the integrator is responsible for per-forming Specific Absorption Rate (SAR) testing in ac-cordance with FCC rules 2.1091. External Antenna Modular approval in the United States is permitted with the use of the integrated antenna ONLY. If an external antenna is used with the AMS-00x module, additional testing of the end product is needed to meet FCC re-quirements. Further Information Additional information regarding FCC certification and use of the AMS-00x module in the United States is available from the following sources.  Federal Communications Commission (FCC) http://www.fcc.gov.au  FCC Office of Engineering and Technology (OET) Laboratory Division Knowledge Database (KDB) http://apps.fcc.gov/oetcf/kdb/index.cfm 7.2 Canada The AMS-00x module has been certified for use in Can-ada under Industry Canada (IC) Radio Standards Specifi-cation (RSS) RSS-210 and RSSGen. Modular approval permits the installation of a module in a host device without the need to recertify the device. Labeling and User Information Requirements Labeling Requirements for the Host Device (from Sec-tion 3.2.1, RSS-Gen, Issue 3, December 2010): The host device shall be properly labeled to identify the module within the host device. The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labeled to display the Industry Canada certification number of the module, preceded by the words “Contains transmit-ter module”, or the word “Contains”, or similar wording expressing the same meaning, as follows: User Manual Notice for License-Exempt Radio Appa-ratus (from Section 7.1.3 RSS-Gen, Issue 3, December 2010): User manuals for license-exempt radio appa-To satisfy FCC RF Exposure requirements for mobile and base station transmission devices, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during operation. To ensure compliance, operation at closer than this distance is not recommended. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter Contains transmitter module IC: 11685A-61F8D

AMS-00x • Embedded Bluetooth Low Energy Solution Regulatory Certification, Section 7 ADS-MS00x-100D4 • Preliminary Data Sheet Page | 13 ©2014 ACKme Networks. http://ack.me October 22, 2014 ratus shall contain the following or equivalent notice in a conspicuous location in the user manual or alterna-tively on the device or both: Transmitter Antenna Notification (from Section 7.1.2 RSS-Gen, Issue 3, December 2010): User manuals for transmitters shall display the following notice in a con-spicuous location: The above notice may be affixed to the device instead of displayed in the user manual. User manuals for transmitters equipped with detach-able antennas shall also contain the following notice in a conspicuous location: Immediately following the above notice, the manufac-turer shall provide a list of all antenna types approved for use with the transmitter, indicating the maximum permissible antenna gain (in dBi) and required imped-ance for each. External Antenna Types Transmitter Antenna (from Section 7.1.2 RSS-Gen, Issue 3, December 2010): The AMS-00x module can only be operated with the on-board antenna with which it was approved without ad-ditional testing. If an external antenna is used with the AMS-00x mod-ule, additional testing of the end product is needed to meet IC requirements as described in the previous sec-tion. Further Information Additional information may be obtained from the In-dustry Canada website at http://www.ic.gc.ca This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Indus-trie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux onditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appa-reil doit accepter tout brouillage radioélectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Can-ada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Indus-trie Canada. Dans le but de réduire les risques de brouil-lage radioélectrique à l'intention des autres utilisa-teurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. This radio transmitter (identify the device by certifi-cation number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s'il fait partie du matériel de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'an-tenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

AMS-00x • Embedded Bluetooth Low Energy Solution Regulatory Certification, Section 7 ADS-MS00x-100D4 • Preliminary Data Sheet Page | 14 ©2014 ACKme Networks. http://ack.me October 22, 2014 7.3 Europe The AMS-00x module is an R&TTE Directive assessed radio module that is CE marked and has been manufac-tured and tested with the intention of being integrated into a final product. The AMS-00x module has been tested to R&TTE Di-rective 1999/5/EC Essential Requirements for Health and Safety Article 3.1(a), Electromagnetic Compatibility (EMC) Article 3.1(b), and Radio Article 3.2 and the re-sults are summarized in Table 11. A Notified Body Opin-ion has also been issued. All AMS-00x test reports are available on the ACKme Networks website at http://ack.me/contact. The R&TTE Compliance Association provides guidance on modular devices in the document titled Technical Guidance Note 01 available on the website at http://www.rtteca.com/html/download_area.htm. Labeling and User Information Requirements The label on the final product which contains the AMS-00x module must follow CE marking requirements. The R&TTE Compliance Association Technical Guidance Note 01 provides guidance on final product CE marking External Antenna Requirements From R&TTE Compliance Association document Tech-nical Guidance Note 01: Provided the integrator installing an assessed radio module with an integral or specific antenna and in-stalled in conformance with the radio module manufac-turer’s installation instructions requires no further evaluation under Article 3.2 of the R&TTE Directive and does not require further involvement of an R&TTE Di-rective Notified Body for the final product. [Section 2.2.4] The European Compliance Testing listed in Table 11 was performed using the AMS-00x on-board antenna. Further Information A document that can be used as a starting point in un-derstanding the use of Short Range Devices (SRD) in Europe is the European Radio Communications Com-mittee (ERC) Recommendation 70-03 E, which can be downloaded from the European Radio Communications Office (ERO) at: http://www.ero.dk. Further information may be obtained from the follow-ing websites:  Radio and Telecommunications Terminal Equip-ment (R&TTE) http://ec.europa.eu/enterprise/rtte/index_en.htm  European Conference of Postal and Telecommuni-cations Administrations (CEPT) http://www.cept.org  European Telecommunications Standards Institute (ETSI) http://www.etsi.org  European Radio Communications Office (ERO) http://www.ero.dk  The Radio and Telecommunications Terminal Equipment Compliance Association (R&TTE CA) http://www.rtteca.com/ NOTE: To maintain conformance to the testing listed in Table 11, the module shall be installed in accordance with the installation instructions in this data sheet and shall not be modified. When integrating a radio module into a completed product the integrator becomes the manufacturer of the final product and is therefore responsible for demonstrating compliance of the final product with the essential requirements of the R&TTE Directive.

AMS00x • Embedded Bluetooth Low Energy Solution Regulatory Certification, Section 7 ADS-MS00x-100D4 • Preliminary Data Sheet Page | 16 ©2014 ACKme Networks. http://ack.me October 22, 2014 7.4 Australia Australian radio regulations do not provide a modular approval policy similar to the United States (FCC) and Canada (IC). However, AMS-00x module test reports may be used in part to demonstrate compliance in ac-cordance with ACMA Radio communications “Short Range Devices” Standard 2004 which references Aus-tralia/New Zealand industry standard AS/NZS-4268:2012. AMS-00x RF transmitter test reports may be used as part of the product certification and compliance folder. For further information regarding the availability of RF test reports, please contact ACKme Networks via our website at http://ack.me/contact. External Antenna Requirements The compliance test reports provided in Table 11 were performed using the AMS-00x on-board antenna. If an external antenna is used with the AMS-00x module, additional testing of the end product is needed to meet Australian regulatory requirements. Further Information Additional information may be obtained from the Aus-tralian Communications and Media Authority website at http://www.acma.gov.au. 7.5 New Zealand New Zealand radio regulations do not provide a modu-lar approval policy similar to the United States (FCC) and Canada (IC). However, AMS-00x module test re-ports may be used in part to demonstrate compliance with the New Zealand “General User Radio License for Short Range Devices”. New Zealand Radio communica-tions (Radio Standards) Notice 2010 references Austral-ia/New Zealand industry standard AS/NZS-4268:2012. AMS-00x RF transmitter test reports may be used as part of the product certification and compliance folder. For further information regarding the availability of RF test reports, please contact ACKme Networks via our website at http://ack.me/contact. External Antenna Requirements The compliance test reports provided in Table 11 were performed using the AMS-00x on-board antenna. If an external antenna is used with the AMS-00x module, additional testing of the end product is needed to meet New Zealand regulatory requirements. Further Information Additional information may be obtained from the New Zealand Radio Spectrum Ministry of Economic Devel-opment website at http://www.rsm.govt.nz.

AMS00x • Embedded Bluetooth Low Energy Solution Packaging, Handling & Storage, RoHS, Section 8 ADS-MS00x-100D4 • Preliminary Data Sheet Page | 17 ©2014 ACKme Networks. http://ack.me October 22, 2014 8 Packaging, Handling & Storage, RoHS 8.1 Packaging AMS00x modules are shipped in a moisture resistant sealed bag. The shelf life of the sealed bag is 12 months at 40°C and <90% Relative Humidity (RH). Please refer to the bag seal date. 8.2 Handling & Storage CAUTION MSL3 Sensitive Device! AMS00x modules are moisture sensitive devices rated at Moisture Sensitive Level 3 (MSL3) per IPC/JEDEC J-STD-20. After opening the moisture sealed storage bag, mod-ules that will be subjected to reflow solder or other high temperature processes must be: 1. mounted to a circuit board within 168 hours at factory conditions (≤30°C and <60% RH) OR 2. continuously stored per IPC/JEDEC J-STD-033 Modules that have been exposed to moisture and envi-ronmental conditions exceeding packaging and storage conditions MUST be baked before mounting according to IPC/JEDEC J-STD-033. Failure to meet packaging and storage conditions will result in irreparable damage to modules during solder reflow. 8.3 RoHS Directive Each AMS00x module is produced according to the RoHS (Restriction of the use of certain Hazardous Sub-stances in electrical and electronic equipment) directive and complies with the directive.

AMS00x • Embedded Bluetooth Low Energy Solution Ordering Information, Section 9 ADS-MS00x-100D4 • Preliminary Data Sheet Page | 18 ©2014 ACKme Networks. http://ack.me October 22, 2014 9 Ordering Information AMS00x modules are available individually or in a bulk tray of TBD units as described in Table 12. Table 12. Ordering Information Part Number Description AMS001/S 1 x AMS001 module with TruConnect pre-installed. Each module is individually packaged in an ESD and MSL3-rated moisture sensitive bag. AMS002/S 1 x AMS002 module with TruConnect pre-installed. Each module is individually packaged in an ESD and MSL3-rated moisture sensitive bag. AMS001/T A single tray containing TBD x AMS001 modules, each with TruConnect pre-installed. The en-tire tray is packaged in an ESD and MSL3-rated moisture sensitive bag. AMS002/T A single tray containing TBD x AMS002 modules, each with TruConnect pre-installed. The en-tire tray is packaged in an ESD and MSL3-rated moisture sensitive bag.

AMS00x • Embedded Bluetooth Low Energy Solution Revision History & Glossary, Section 10 ADS-MS00x-100D4 • Preliminary Data Sheet Page | 19 ©2014 ACKme Networks. http://ack.me October 22, 2014 10 Revision History & Glossary 10.1 Revision History Table 13: Document Revision History Revision Date Change Description ADS-MS00x-100D4 22-Oct-2014 Section 7 Regulatory Certification 10.2 Glossary In most cases, acronyms and abbreviations are defined on first use. A comprehensive list of acronyms and other terms used in ACKme Networks documents are provided on the ACKme Networks website at http://ack.me/FAQs/Glossary.

AMS00x • Embedded Bluetooth Low Energy Solution ACKme reserves the right to make changes without further notice to any products or data herein to improve reliability, function, or design. Information furnished by ACKme is believed to be accurate and reliable. However, ACKme does not assume any liability arising out of the application or use of this information, nor the application or use of any product described herein, neither does it convey any license under its patent rights nor the rights of others. ACKme Networks US Headquarters: Australian Office: 2 North Santa Cruz Ave Level 21, Tower 2 Suite #207 201 Sussex St Los Gatos CA 95030 Sydney NSW 2000 © 2014 ACKme Networks Inc. All rights reserved. ADS-MS00x-100D4 • Preliminary Data Sheet October 22, 2014 Contact Information +1 (408) 402 5708 http://ack.me/contact Phone:

Navigation menu