Sintai Optical CWFB124 Wi-Fi module User Manual CWFB124 QIG 20130923

Download:
Mirror Download [FCC.gov]
Document ID	2089088
Application ID	LSkWgdxcZlyfEUZVruBdJQ==
Document Description	User Manual.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	147.68kB (1846024 bits)
Date Submitted	2013-10-01 00:00:00
Date Available	2013-10-01 00:00:00
Creation Date	2013-09-23 10:43:01
Producing Software	Bullzip PDF Printer / www.bullzip.com / Freeware Edition
Document Lastmod	2013-09-27 15:12:26
Document Title	CWFB124_QIG 20130923.pdf
Document Author:	kaoder

FIOF
Imaging Technology
CWFBlZ4
WLAN SiP Module
- WLAN 802.11 b/g/n SDIO
Quick Installation Guide
I. Installation steps
1. First, install Realtek Wireless LAN 8189ES Driver & Utility into Windows XP system of your
Notebook.
2. Follow the instructions of the driver wizard. and complete all the steps.
3. After that, system will ask you to restart the computer.
4. Once system is again ready. insert the Express cmditoisDIO interface card into the express card
slut.
5. Then plug in the SDIO fixture card with CWFB124.
6. Continue the steps as New Hardware Wizard suggests.
7. Windows XP System will find the installed driver and you should complete all the suggested
steps.
8. Then you can find the shortcut of Realtek S 189ES Wireless LAN Utility on the desktop, click
on it.
9. You can also find the APs around you in the available network page, select the one you want to
connect.
10. Configure the right wireless settings.
1 1. Make sure the connection is built. You can now go surfing on the Web wirclcssly.
||. Functional Specification
Standard
Radio Technology
Modulation Type
Transfer rate
Frequency Range
Operating Channel
Rating
Operating Temperature
IEEE 802.11b, IEEE 802.119, IEEE 802.11n
802.11b / DSSS, 802.11g , 802.11n / OFDM
64QAM, 160AM,QPSK, BPSK for OFDM
CCK, DQPSK, DBPSK for DSSS
802.11b2upt011Mbps
802.11g: up to 54Mbps
802.11n (ZOMHZ, 800ns Gl):up to 65
Mbps(Nss:1);
802.11n (40MHz, 800ns Gl):up t0135
Mbps(Nss:1);
802.11n (ZOMHZ, 400ns Gl):up to
72.2Mbps(Nss:1);
802.11n (40MHz, 400ns Gl):up to 150
Mbps(Nss:1);
Note: NSS - Number of Spatial Streams
2412MHZ~2462MHZ
DC 3.3V from host
+0~40 degree C
Federal Communication Commission Interference
Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following measures:
7 Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
7 Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
7 Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and
users, and
2) The transmitter module may not be coilocated with any other transmitter or antenna.
3) For all products market in US, OEM has to limit the operation channels in CH1 to CH1 1
for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or
info to the end-user regarding to Regulatory Domain change.
As long as 3 conditions above are met, further transmitter test will not be required. However,
the OEM integrator is still responsible for testing their endiproduct for any additional
compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain
laptop configurations or corlocation with another transmitter), then the FCC authorization is
no longer considered valid and the FCC ID L110! be used on the final product. In these
circumstances, the OEM integrator will be responsible for reievaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final end
product must be labeled in a visible area with the following: “Contains FCC ID:
SERCWFB124”. The grantee‘s FCC ID can be used only when all FCC compliance
requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how
to install or remove this RF module in the user’s manual of the end product which integrates
this module.
The end user manual shall include all required regulatory information/warning as show in this
manual.
Industry Canada statement:
This device complies with 11557210 of the Industry Canada Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Ce dispositif est conforme a la norme CNR7210 d'lndustrie Canada applicable aux appareils radio
exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) 1e dispositif ne
doit pas produire de hrouillage pre’judiciahle, et (2) ce dispositif doit accepter tout hrouillage recu, y
compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should he installed and operated with minimum distance 20cm
between the radiator & your body.
Declaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC étahlies pour un
environnement non controlé. Cet équipement doit etre installé et utilise avec un minimum de 20 cm
de distance entre la source de rayonnement et votre corps.
This device is intended only for OEM integrators under the following conditions: (For
module device use)
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
Z) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the
OEM integrator is still responsible for testing their end-product for any additional compliance
requirements required with this module installed.
Cet appareil est coneu uniquement pour les intégrateurs OEM dans les conditions suivantes:
(Pour utilisation de dispositil module)
1) L‘antenne doit etre installe’e de telle sorte qu'une distance de 20 cm est respecte’e entre l'antenne
et les utilisateurs, et
2) Le module emetteur peut ne pas étre coimplanté avec un autre émetteur ou antenne.
Tant que les 2 conditions ciedessus sont remplies, des essais supple’mentaires sur l'e’metteur ne
seront pas necessaires. Toutefois, l'integrateur OEM est toujours responsable des essais sur son
produit final pour toutes exigences de conformité supplementaires requis pour ce module installe.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or
coelocation with another transmitter), then the Canada authorization is no longer considered valid
and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will
be responsible for reeevaluating the end product (including the transmitter) and obtaining a separate
Canada authorization.
NOTE IMPORTANTE:
Dans le cas oil ces conditions he peuvent étre satisfaites (par exemple pour certaines configurations
d'ordinateur portable ou de certaines coelocalisation avec un autre émetteur), l'autorisation du
Canada n'est plus considére comme valide et l'ID IC ne peut pas étre utilise sur le produit final.
Dans ces circonstances, l'intégrateur OEM sera charge de réévaluer le produit final (y compris
l'émcttcur) et l'obtention d'unc autorisation distincte au Canada.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed
such that 20 cm may be maintained between the antenna and users. The final end product must be
labeled in a visible area with the following: “Contains IC: 11195A7 CWFB124”.
Plaque signalétique du produit final
Ce module e’metteur est autorise’ uniquement pour une utilisation dans un dispositif oil l'antenne
peut étre installée de telle sorte qu‘une distance de 200m peut étre maintenue entre l'antenne et les
utilisateurs. Le produit final doit etre e’tiquete’ dans un endroit visible avee l'inseription suivante:
"Contient des IC: 11195A- CW'FB124".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to
install or remove this RF module in the user’s manual of the end product which integrates this
module.
The end user manual shall include all required regulatory information/warning as show in this
manual.
Manuel d'information a l'utilisateur final
L'intégratcur OEM doit Etrc conscicnt do no pas fournir dcs informations ‘a l'utilisatcur final quant a
la fagon d'installer ou de supprimer ce module RF dans le manuel de l‘utilisaleur du produit final qui
int‘cgrc cc module,
Le manuel de l'utilisateur final doit inclure toutes les informations re’glementaires requises et
avertissements eomme indique dans ce manuel.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2013:09:23 10:43:01+08:00
Modify Date                     : 2013:09:27 15:12:26+08:00
Metadata Date                   : 2013:09:27 15:12:26+08:00
Format                          : application/pdf
Creator                         : kaoder
Title                           : CWFB124_QIG 20130923.pdf
Producer                        : Bullzip PDF Printer / www.bullzip.com / Freeware Edition
Document ID                     : uuid:2177caff-462f-4eca-b50e-2942b9bfd704
Instance ID                     : uuid:0e29871f-cc55-4eeb-8d10-11097d3fc52b
Page Count                      : 8
Author                          : kaoder

EXIF Metadata provided by EXIF.tools