Skidata ASX70KT Port. Keyterminal for 123 kc and 13.56 Mc keycards User Manual Manual KeyTerminal AS x70 KT

Skidata AG Port. Keyterminal for 123 kc and 13.56 Mc keycards Manual KeyTerminal AS x70 KT

User manual

ManualKeyTerminalASx70KT
Installation & Maintenance Instructions KeyTerminal AS x70 KT Page 2 © SKIDATA AG, June 2003 SKIDATA AG Technical Documentation Untersbergstrasse 40 A-5083 Gartenau Telephone +43-(0)6246 888-0, Telefax +43-(0)06246 888-7 Internet http://www.skidata.com e-mail docu@skidata.com Copyright © 2003 by SKIDATA AG. All rights reserved. All information in the following document is protected by copyright law. No part of this document may be reproduced without the written consent of SKI-DATA AG. SKIDATA AG reserves the right to make any changes of specification and other information in this document without further notice. Please note During the compilation of this Technical Documentation, great care has been taken to ensure the accuracy of the information contained in it. However, despite our constant effort to ensure the highest degree of accuracy and comprehensiveness possible, the information provided cannot be guaranteed to be absolutely error-free. Trademarks This documentation may contain representations of registered product or service trademarks owned by SKIDATA AG or third parties, as well as references to proprietary know-how protected by copyright laws or other legal provisions. In any case the intel-lectual property rights remain exclusively with their respective owners. Declaration of Conformity The KeyTerminal AS x70 KT product family have been devel-oped, designed and manufactured in accordance with the follow-ing EU directions: R&TTE (99/5/EC) 0408 List of EU countries where these KeyTerminals may be sold: AT, DE, FI, FR, IT, SE Version June 2003
KeyTerminal AS x70 KT Installation & Maintenance instructions © SKIDATA AG, June 2003 Page 3 FCC 15.19: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause un-desired operation. FCC 15.21: IMPORTANT: Any changes to or modifications of AS x70 KT (all variants) unless expressly approved by SKIDATA™, may void the user's authority to operate this device.
Installation & Maintenance Instructions KeyTerminal AS x70 KT Page 4 © SKIDATA AG, June 2003 KeyTerminal AS x70 KT 1 Document Management – Version Table Tab. 1: Document Version Table for Installation & Maintenance Instructions Section Document Pages Version Date 1 KeyTerminal AS x70 KT 4 1.0 17-06-2003
KeyTerminal AS x70 KT 1 1 KeyTerminal AS x70 KT Version 1.0 4 pages Copyright 2003 by SKIDATA AG
1 KeyTerminal AS x70 KT 1.1 Contents Page 2 © SKIDATA AG, Version 1.0 1.1 Contents 1.1 Contents 2 1.2 Electrical connections of the device 3
KeyTerminal AS x70 KT 1 Electrical connections of the device 1.2 © SKIDATA AG, Version 1.0 Page 3 1.2 Electrical connections of the device  Plug the circular connector of the power adapter into its coun-terpart on the backside of the interface connector.  Plug the flat connector of the interface cable into its counter-part on the KeyTerminal (below the key ‘0’)  Plug in the power adapter. These connections are sufficient to power the KeyTerminal from mains and to charge the rechargeable battery pack.  Depending on the variant of the KeyTerminal, the interface cable comes either with a 9-pin female or male connector. The female connector is used to be connected to an RS 232 interface (COM), while the male connector is designed for a connection to a modem.
1 KeyTerminal AS x70 KT 1.2 Electrical connections of the device Page 4 © SKIDATA AG, Version 1.0 Fig. 1: Connection KeyTerminal

Navigation menu