Skidata SD905 RFID Reader Module User Manual SKIDATA Vorlage

Skidata AG RFID Reader Module SKIDATA Vorlage

User Manual

RFID Reader Module sd905 Integration Manual FCC ID QSS-SD905 IC:6215A-SD905 Author: SOCH Version: 1.3 2016-12-21
RFID Reader Module sd905 © 2016 SKIDATA AG Table of Contents Page 2 of 23 SKIDATA AG Untersbergstraße 40 A-5083 Grödig/Salzburg Phone: +43 6246 888-0 Fax: +43 6246 888-7 Internet: http://www.skidata.com e-mail: info@skidata.com Copyright © 2016 by SKIDATA AG. All rights reserved. All information in the following document is protected by copyright law. No part of this document may be reproduced without the written consent of SKIDATA AG. SKIDATA AG reserves the right to make any changes of specification and other information in this document without further notice. Note Great care was taken to make the information contained in this documentation as correct and accurate as possible. Although the documentation is updated regularly, SKIDATA AG cannot guarantee absolute correctness and completeness of the information contained therein. Trademarks This documentation may contain representations of registered product or service trademarks owned by SKIDATA AG or third parties, as well as references to proprietary know-how protected by copyright laws or other legal provisions. In any case all rights remain exclusively with their respective owners. SKIDATA® is a registered trademark of SKIDATA AG in the USA, the European Union and other countries. Version History Date Version Changed by Description of Changes 2016-05-18 1.0 SOCH 2016-08-09 1.1 SOCH Minor changes 2016-08-22 1.2 SOCH New Antennas: sd901 and sd902 2016-12-21 1.3 SOCH Chapter 3 revised
RFID Reader Module sd905 © 2016 SKIDATA AG Table of Contents Page 3 of 23 1. Table of Contents 1. Table of Contents ....................................................................................................................................... 3 2. General ........................................................................................................................................................ 4 3. sd905 ........................................................................................................................................................... 6 3.1 Connectors of the sd905 ............................................................................................................................ 6 3.2 Technical Characteristics ........................................................................................................................... 7 3.3 Description ................................................................................................................................................. 7 4. Antennas ..................................................................................................................................................... 8 5. Integration into Devices ........................................................................................................................... 21 5.1 Integration into CO LIGHT ....................................................................................................................... 21 5.2 Integration into Ski Antenna ..................................................................................................................... 22 6. Labeling ..................................................................................................................................................... 23 7. DECLARATIONS OF CONFORMITY ........................................................................................................ 23
RFID Reader Module sd905 © 2016 SKIDATA AG General Page 4 of 23 2. General Validity This manual describes the sd905 RFID Reader Module into hosts, e.g. the Coder LIGHT (CO LIGHT). Addressees This manual is written exclusively for specialists. The descriptions in this manual are intended for personnel trained by the manufacturer. The information in this manual cannot substitute the product training. The content of this manual is intended for use by the following groups of people: — Project manager Project manager who is responsible for the system and entrusted with project planning and realization. — Fitter Person specialized in mounting and installation. Person who has an adequate technical training and sufficient experience and who has been authorized by the manufacturer after completing the training on the product. — Service technician Specialist for initial set-up and maintenance of the installation. Person who has an adequate technical training and sufficient experience and who has been authorized by the manufacturer after completing the training on the product. — Network administrator Realizes the set-up of the device within the network and makes sure that the devices are accessible within the network. — Software partner Specialists for connecting the system to the user software by defining operating and booking sequences, programming the customer applications and setting the parameters of the devices. NOTICE! For reasons of device safety, some of the activities might only be carried out by the SERVICE PERSON. Only persons of the groups "Fitter" and "Service technician" have the status of a SERVICE PERSON according to EN 60950-1:2006. Contents and purpose The contents are limited to the assembly and installation of the hardware.
RFID Reader Module sd905 © 2016 SKIDATA AG General Page 5 of 23 ESD (electro static discharge) protective measures CAUTION — Danger for electronic components due to electrostatic discharge. — Improper handling of printed circuit boards or components can cause damages that lead to complete failures or sporadic errors. — During installation and repair of the device, the ESD protective measures must be considered. Please consider the following guidelines before the installation or maintenance of the device: — Always carry an ESD antistatic wristband when dealing with electronic components. Connect one part of the wristband with a discharge socket or an unvarnished grounded metal component. This way, static charges are discharged from your body securely and effectively. — Only touch the printed circuit boards at the edges. Do not touch the printed circuit board itself or the connector. — Place all dismantled components on an anti-static surface or in an anti-static container. — Avoid contact between printed circuit boards and your clothing. The wristband only protects the printed circuit boards against electrostatic discharge from the body, but there is still a risk of damage through electrostatic discharge from your clothing. — Transport and dispatch dismantled modules only in electrostatically shielded protective bags.
RFID Reader Module sd905 © 2016 SKIDATA AG sd905 Page 6 of 23 3. sd905 3.1 Connectors of the sd905 Fig. 1: Connectors of the sd905, top side Fig. 2: Connectors of the sd905, bottom side
RFID Reader Module sd905 © 2016 SKIDATA AG sd905 Page 7 of 23 3.2 Technical Characteristics — Dimensions: 93 mm × 51 mm — Operating frequencies: 13,56 MHz — Modulation: ASK — Pulse repetition rule: 100 ms typ. — Supply Voltage: 5 V — Operating Temperature: −30 °C to +85 °C — Compatible with RFID data carriers supported by SKIDATA systems — Compatible with data carriers compliant to ISO 15693 and ISO 14443 3.3 Description The sd905 functions as a built-in interface between a SKIDATA device and contactless data carriers (RFID). Data communication between the sd905 and the SKIDATA device is provided by means of a 0 V/5 V RS232 data link or a USB connection. The most basic communication scenario is where the (unique) serial number of the data carrier is sent to the RFID interface. This may or may not lead to further data communication between the data carrier and RFID interface, and it may or may not lead to communication, via data link, between the RFID interface and connected devices. The sd905 is equipped with two amplifier stages. These stages may be used to drive two antennas independently, or to drive one antenna in bridge connection. In case of a bridge connection the amplifier stages will be driven inversely phased. An antenna for bridge connection must be equipped with a special connector to be connected to X015 of the sd905. This special connector will be explicitly mentioned at the description of the respective antenna in chapter 4. The main purposes of the sd905 RFID interface are: — Coding of RFID data carriers. SKIDATA coding devices use sd905 as an RFID transceiver module for encoding RFID data carriers before issuing them to the user. — Access control. SKIDATA access control devices use sd905 for reading RFID data carriers. Depending on the validity details stored on the data carrier, access is granted or refused.
RFID Reader Module sd905 © 2016 SKIDATA AG Antennas Page 8 of 23 4. Antennas Fig. 3: sd571 Fig. 4: sd572
RFID Reader Module sd905 © 2016 SKIDATA AG Antennas Page 9 of 23 Fig. 5: sd611 Fig. 6: sd612
RFID Reader Module sd905 © 2016 SKIDATA AG Antennas Page 10 of 23 Fig. 7: sd647 Fig. 8: sd648
RFID Reader Module sd905 © 2016 SKIDATA AG Antennas Page 11 of 23 Fig. 9: sd682/1 Only the 13 MHz antenna is used with sd905; the 122 kHz antenna remains unused Fig. 10: sd682 Antennas A, B and C
RFID Reader Module sd905 © 2016 SKIDATA AG Antennas Page 12 of 23 Fig. 11: sd697/2 Only the 13 MHz antenna is used with sd905; the 122 kHz antenna (wired coil) remains unused Fig. 12: 697/3 Only the 13 MHz antenna is used with sd905; the 122 kHz antenna remains unused
RFID Reader Module sd905 © 2016 SKIDATA AG Antennas Page 13 of 23 Fig. 13: sd733/2 Only the 13 MHz antenna is used with sd905; the 122 kHz antenna remains unused Fig. 14: sd733
RFID Reader Module sd905 © 2016 SKIDATA AG Antennas Page 14 of 23 Fig. 15: sd758 (Shortrange module) Only the 13 MHz antenna is used with sd905; the 122 kHz antenna remains unused Fig.16: sd794/2
RFID Reader Module sd905 © 2016 SKIDATA AG Antennas Page 15 of 23 Fig.17: sd794 Antennas A and B Fig. 18: sd847 Antennas A and B The sd847 acts as an antenna, as an illumination and as a touch key. The antenna part is completely independent from all other parts.
RFID Reader Module sd905 © 2016 SKIDATA AG Antennas Page 16 of 23 Fig. 19: sd862 Antennas A and B The sd862 acts as an antenna, as an illumination and as an illuminated touch key. The antenna part is completely independent from all other parts. The square part is the illuminated touch key and may or may not be removed.
RFID Reader Module sd905 © 2016 SKIDATA AG Antennas Page 17 of 23 Fig. 20: sd872 The sd872 acts as an antenna and as an illumination. The antenna part is completely independent from the illumination.
RFID Reader Module sd905 © 2016 SKIDATA AG Antennas Page 18 of 23 Fig. 21: sd877 Antennas A and B The sd877 acts as an antenna and as an illumination. The antenna part is completely independent from the illumination.
RFID Reader Module sd905 © 2016 SKIDATA AG Antennas Page 19 of 23 Fig. 22: sd888 Antennas A and B The sd888 is equipped with a special connector which fits into X015 of the sd905 and will therefore be powered as a bridge circuit.
RFID Reader Module sd905 © 2016 SKIDATA AG Antennas Page 20 of 23 Fig. 23: sd901 Fig. 24: sd902
RFID Reader Module sd905 © 2016 SKIDATA AG Integration into Devices Page 21 of 23 5. Integration into Devices 5.1 Integration into CO LIGHT Fig. 25: Inside view of CO LIGHT with shows sd905 wih Antenna sd572
RFID Reader Module sd905 © 2016 SKIDATA AG Integration into Devices Page 22 of 23 5.2 Integration into Ski Antenna Fig. 26: Inside view of Ski Antenna which shows sd905 with Antenna sd888
RFID Reader Module sd905 © 2016 SKIDATA AG Integration into Devices Page 23 of 23 6. Labeling Using a permanently affixed label, the modular transmitter will be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. The same applies to the IC (Industry Canada) identification number. This exterior label can use wording such as the following: For the USA: “Contains Transmitter Module FCC ID QSS-SD905” or “Contains FCC ID QSS-SD905”. Any similar wording that expresses the same meaning may be used. For Canada: “Contains Transmitter Module IC:6215A-SD905” or “Contains IC:6215A-SD905”. Any similar wording that expresses the same meaning may be used. 7. DECLARATIONS OF CONFORMITY USA: DECLARATION OF CONFORMITY according to FCC Part 15: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Canada: DECLARATION OF CONFORMITY This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Navigation menu