Skyrocket Toys 01598RX24G Sky Viper Nano Drone User Manual 01598 ENF16 SVNano IM 050416 PREVIEW
Skyrocket Toys LLC Sky Viper Nano Drone 01598 ENF16 SVNano IM 050416 PREVIEW
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3021599 |
| Application ID | fnbD028Qa042Iv1fQjPp6Q== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 121.42kB (1517786 bits) |
| Date Submitted | 2016-06-08 00:00:00 |
| Date Available | 2016-06-08 00:00:00 |
| Creation Date | 2016-05-04 17:04:43 |
| Producing Software | Adobe PDF library 10.01 |
| Document Lastmod | 2016-06-03 11:05:26 |
| Document Title | 01598_ENF16_SVNano_IM_050416._PREVIEW |
| Document Creator | Adobe Illustrator CS6 (Macintosh) |
FLYING GUIDE 01598 NANO DRONE POWERING UP AND PAIRING (WITH ALTITUDE ON) OFF ON Place drone on flat surface. Turn on drone. Turn on remote. Wait for flashing green lights to turn solid. FLYING BASICS TOGGLE INTO MANUAL FLIGHT BEFORE TAKE-OFF • Hold stunt button and press auto land/auto launch button and a tone will sound from the remote. Make sure your throttle stick is in the down position. • Push the throttle stick up to begin manual flight. Press Auto Launch to launch a few feet off the ground. Press the Altitude button to fly approximately 12” higher or lower. TOGGLE INTO MANUAL FLIGHT WHILE IN AUTO-HOVER • Hold stunt button and press auto land/auto launch button and a tone will sound from the remote. Make sure your throttle stick is in the down position. • After the tone is heard, move the throttle stick up until the drone starts to rise. (If throttle is not matched in 5 seconds then manual flight will be cancelled.) TOGGLE INTO AUTO HOVER WHILE IN MANUAL FLIGHT • Press either the up or down altitude locking button to toggle back into auto hover. (Your drone will hover at the current throttle.) Press the directional Thumbstick to fly in any direction. Press the Auto Land button to land. FLYING TIPS FLIGHT CONTROLS Press up to lift THROTTLE/ROTATION STICK • While in manual flight mode push the throttle stick forward to make drone lift. • The further you push the throttle stick, the faster you lift. Up and down controls only apply to manual flight mode. Power On/off Switch/sensitivity Switch DIRECTION STICK • Push the direction stick forward to fly forward or away from you (Green blade in front). Push backwards to fly backward. The further you push, the faster the drone will fly in that direction. • Push the direction stick left to fly left. Push right to fly right. The further you push, the faster the drone will fly sideways. • If your drone drifts in any direction when you are hovering, you will need to make Trim adjustments to correct the driving. Trim adjustments are sometimes needed when the drone is first flown after purchase. See TRIM ADJUSTMENTS section for details. • Practice launching, hovering and landing before attempting to learn other moves. Forward/Backward Trim Power indicator LED THROTTLE/ ROTATION STICK When launching the drone, face the same direction as the drone. Green blades and green LEDs should be in front. Press up to fly forward • Press down to fly backward Flying 2 to 3 feet above the ground will reduce ground turbulence and make flying easier. • When first attempting to fly in different directions, start by tapping the direction stick until you have a feel for it. Always move controls slowly until you become comfortable operating the drone. Press left to fly left • Once you’ve mastered flying in directions, practice rotational controls. Spinning and keeping drone facing the same direction as you makes flying easier and more intuitive. • Stay 2 to 3 feet away from walls and ceilings as drone will be drawn towards them if you fly too close. • If propeller blades come in contact with another object or you crash, throttle down or auto land immediately to prevent possible or further damage. • If anything prevents drone’s blades from spinning or they become jammed, throttle down or auto land immediately. Do not attempt to fly until obstruction has been removed and damage fixed. • Should something prevent drone’s blades from spinning, drone may auto shutdown. LiPo battery will need to be unplugged then reconnected to restore flying power. • If the drone flies too far away, beyond the control range of the remote, the drone will auto-land to prevent the drone from flying away out of control. Stunt Button Press down to descend • DIRECTION STICK Press left to rotate counterclockwise Press right to rotate clockwise Press right to fly right Left/Right Trim Rotation Trim ALTITUDE BUTTONS • Press the up or down arrow to adjust the drone’s altitude. The drone will lift or lower approximately 12” each time the up or down arrow is pressed. (Distance may vary.) • Hold the up or down buttons for continuous lift or descent. AUTO LAUNCH/LAND BUTTON • Press the auto launch button to launch a few feet from the ground. (Exact height may vary.) • Press the auto land button to land the drone by itself. FLIGHT SENSITIVITY SWITCH The Drone’s responsiveness may be adjusted on the Controller to match your flying skills. There are three choices: 1 LOW sensitivity 2 HIGH sensitivity It is best to start in the low sensitivity position until you have mastered flying. Flight sensitivity can be adjusted before or during flight. HIGH LOW OFF OFF Online Video Instructions & Flying Tips available now at SKYVIPER.COM TRIM ADJUSTMENTS If the drone drifts in any direction while hovering (and you are not pressing the direction stick), you may need to make trim adjustments. Press the recommended trim button as described below to make adjustments. Tip 1: When the remote LED flashes 3 times quickly, the trim will revert back to middle of trim range. Tip 2: If you are uncomfortable trimming the drone in flight, you can land onto a flat surface and make your trim adjustments. If the drone drifts forward – Press B button If the drone drifts backwards – Press F button If the drone drifts left – Press R button If the drone drifts right – Press L button NOTE: Trim adjustments will remain saved until remotes batteries are removed. If the drone spins counter-clockwise, when viewed from the top – Press button If the drone spins clockwise, when viewed from the top – Press button TROUBLESHOOTING ONE TOUCH STUNTS PROBLEM SOLUTION Drone drifts in any direction during flight without direction from the remote • Adjust the trim controls until drifting ceases. NOTE: BARREL ROLL While flying forward (or reverse), Once a stunt has been initiated, DO NOT adjust Throttle or press any other controls until the stunt has been completed. tap the stunt button. All blades spin, but drone will not fly properly or crashes immediately • Drone’s blade may have been installed incorrectly. Reinstall and remember that the GREEN blades point forward. Drone is unresponsive • • • Drone crashes when attempting stunt functions • Ensure the remote has fresh batteries and the LiPo battery is fully charged. Drone may be miscalibrated by launching from an un-level surface. Turn the remote off. Turn off the drone then turn them back on and try again from a flat, level launching surface. Inspect drone for any possible damage. Ensure that drone is flying a minimum distance of 6 feet from the ground with a minimum 6 feet clearance in all directions. FLIP 1 Bring the drone to a mid-air hover without flying in any direction. Remove finger from the direction stick. 2 While hovering, tap and hold the stunt button. 3 Then quickly tap the direction stick in the direction you want the drone to flip. ADULT SUPERVISION REQUIRED CAUTION! The drone should be flying at least 6 feet in the air with a minimum clearance of 6 feet in all directions before attempting stunt functions. CONTENTS REMOTE BATTERIES • Nano Drone • USB Charging Cable • Remote Control • 4 Replacement Blades Loosen the screw in the Remote Control battery compartment door with a Phillips screwdriver and insert batteries as shown. Replace door and tighten screw. – AAA/LR03/R03 1.5V + + AAA/LR03/R03 1.5V – 3 x1.5 V AAA (LR03) + AAA/LR03/R03 1.5V – Before each use, an adult should check this product and the LiPo battery to ensure no damage or hazards exist. Drone has rotating blades that move at high speed, posing danger of damage and injury. Pilots are responsible for any actions that result in damage or injury from the improper operation of drone. Adequate flying space is required. Avoid flying near interior fans and/or vents as they may make flying difficult to control. Keep a safe distance away from streets, public thoroughfares and power lines. Never attempt to retrieve drone from any location higher than your reach (such as rooftops or trees) or from any location that poses a safety hazard. Never fly drone at night. Keep drone in sight at all times during operation. Discontinue operation immediately if drone flies out of your field of view. Do not fly near spectators or animals. Pets can become excited about R/C vehicles therefore keep away from pets at all times. Keep spinning rotors away from fingers, hair, eyes and other body parts. Always launch from a flat surface. Never leave drone unattended while it is turned on. Read all enclosed information before operating. CHARGING THE DRONE CHARGING PRECAUTIONS: OF F ON Charging cord 1 Turn drone off. Connect charging cord to plug on drome. OFF • After use, allow drone (battery on bottom) to cool down to room temperature before charging again. • Charge drone in an isolated area, away from excessive heat or moisture. • If you suspect that the battery is damaged or swelling, turn off the drone immediately. • Do not modify, heat, or wet the battery in any way. Only recharge with provided charger. ON Turn on drone. 2 Plug charging cord into computer or USB power block. Plug in USB cable 3 Red light = charging Green light = fully charged This device complies with PART 15 of the FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna - Increase the separation between the equipment and receiver - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected - Consult the dealer or an experienced radio/TV technician for help. Remove all packaging attachments before giving the toy to a child. Not suitable for children under 3 years due to small parts that could be swallowed. Conforms to product safety standards ASTM F963. Keep instructions for future reference. Do not discard. ® ©2016 Skyrocket Toys LLC, Los Angeles CA 90066 USA. All Rights Reserved. Sky Viper and Skyrocket and their respective logos are trademarks and/or registered trademarks of Skyrocket Toys LLC. All other trademarks, logos and copyrights are the property of their respective owners, and there is no relationship express or implied with Skyrocket Toys LLC. MADE IN CHINA THIS PRODUCT CONTAINS A LITHIUM-POLYMER BATTERY 3.7V 100mAh: LiPo batteries have a severe risk of fire and injury if they are improperly handled or misused. They may explode, overheat or ignite. Read all following precautions and instructions regarding the care and use of LiPo batteries. The built-in LiPo battery is only to be used with the drone and charger included with this product. • Remove exhausted batteries as soon as possible and discard properly. • Keep away from flammable materials. • Remove all batteries from the compartment if toy is not used for a long period. • Do not expose to direct sunlight. • The supply terminals are not to be short circuited. • Do not place in fires or leave in hot places. • Never throw batteries in a fire or attempt to open outer casing. • Do not drop or make subject to strong impact. • Keep dry and away from water. LiPo Battery Disposal: LiPo batteries must be recycled or disposed of properly. They should not be disposed of with other household waste. Check your local laws and regulations for correct ALKALINE BATTERY CAUTIONS • Do not use rechargeable batteries. • Remove exhausted batteries as soon as possible and discard properly. • Different types of batteries or new and old batteries are not to be mixed. • Remove all batteries from compartment if toy is not used for a long period. • Batteries are to be inserted using correct polarity. • Never throw batteries in a fire or attempt to open the outer casing. WARNING: Batteries are harmful if swallowed. Please keep away from children. Battery Disposal: Dispose of batteries according to the local laws and regulations of your region. Some batteries may be recycled, and may be accepted for disposal at your local recycling centre. If you are not able to identify the applicable rules in your area, please check the instructions of the battery manufacturer. recycling and/or battery disposal. The software included in this product contains copyrighted software that is licensed under the GPLv3. A copy of that license is included in our website at the URL below. You may obtain the complete Corresponding Source code from us for a period of three years after our last shipment of this product and/or spare parts therefor, which will be no earlier than 05-01-2019, on our website at http://www.skyrockettoys.com/GPL/
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No XMP Toolkit : Adobe XMP Core 5.6-c015 81.157285, 2014/12/12-00:43:15 Format : application/pdf Title : 01598_ENF16_SVNano_IM_050416._PREVIEW Metadata Date : 2016:06:03 11:05:26+08:00 Modify Date : 2016:06:03 11:05:26+08:00 Create Date : 2016:05:04 17:04:43-07:00 Creator Tool : Adobe Illustrator CS6 (Macintosh) Thumbnail Width : 256 Thumbnail Height : 108 Thumbnail Format : JPEG Thumbnail Image : (Binary data 10386 bytes, use -b option to extract) Instance ID : uuid:52155e43-e163-4275-8a67-d409d416b7e9 Document ID : xmp.did:5D353EA43920681183D1A858E3736B30 Original Document ID : uuid:5D20892493BFDB11914A8590D31508C8 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:5C353EA43920681183D1A858E3736B30 Derived From Document ID : xmp.did:5C353EA43920681183D1A858E3736B30 Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8 Derived From Rendition Class : proof:pdf History Action : saved, saved History Instance ID : xmp.iid:FB7F11740720681183D1F7CD751CB142, xmp.iid:5D353EA43920681183D1A858E3736B30 History When : 2016:04:14 19:01:43-07:00, 2016:05:04 17:04:33-07:00 History Software Agent : Adobe Illustrator CS6 (Macintosh), Adobe Illustrator CS6 (Macintosh) History Changed : /, / Manifest Link Form : EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference Manifest Reference File Path : /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone front.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone switch.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Controller2-165.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Controller2-165.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone top.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Controller2-165.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Controller2-165.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone top.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone top.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone top.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Nano047 copy.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Nano047 copy.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Nano047 copy.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/CONTROLLER A.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/CONTROLLER A.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/CONTROLLER A.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/CONTROLLER A.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Nano047 copy.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Nano047 copy.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Nano047 copy.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Nano047 copy.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Controller2-165.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/remote battery.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Controller2-165.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Controller2-165.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Controller2-165.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Controller2-165.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Nano047 copy.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/streaming_Controler_gry.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Controller2-165.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone switch.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone switch.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone battery charging.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/Controller2-165.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone top.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone top.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/drone top.png, /Users/suzannehackel/Desktop/Szn_temp/Szn_files/INSTRUCTIONS/Skyviper_Ins/skyviper/SV_IMS_5_4/01662_ENF16_TRU_SVHDStuntVideo_IM/Images/front.png Startup Profile : Print Has Visible Overprint : False Has Visible Transparency : True N Pages : 1 Max Page Size W : 11.692912 Max Page Size H : 16.535414 Max Page Size Unit : Inches Font Name : EurostileRegular, EurostileBold, Myriad-Roman, EurostileLTStd-Ex2, EurostileLTStd-BoldEx2, PirulenRg-Regular Font Family : Eurostile, Eurostile, Myriad, EurostileLTStd Ex2, EurostileLTStd BoldEx2, PirulenRg Regular Font Face : Regular, Bold, Roman, Ex2, BoldEx2, Regular Font Type : Open Type, Open Type, Type 1, Open Type, Open Type, Unknown Font Version : Version 1.51, Version 1.51, 001.001, OTF 1.029;PS 001.003;Core 1.0.33;makeotf.lib1.4.1585, OTF 1.029;PS 001.003;Core 1.0.33;makeotf.lib1.4.1585, OTF 1.006;PS 001.000;Core 1.0.23;hotunix 1.28 Font Composite : False, False, False, False, False, False Font File Name : Eurostile, Eurostile, MyriaRom; Myriad, EurostileLTStd-Ex2.otf, EurostileLTStd-BoldEx2.otf, MyriadPro-Regular.otf Plate Names : Cyan, Magenta, Yellow, Black, PANTONE 294 C, PANTONE 294 C copy, Deleted Global Color Swatch Groups Colorants Tint : 100.000000 Swatch Groups Colorants L : 18.823500 Swatch Groups Colorants A : 4 Swatch Groups Colorants B : -43 Swatch Groups Group Name : Grays Swatch Groups Group Type : 1 Swatch Groups Colorants Swatch Name: C=0 M=0 Y=0 K=100 Swatch Groups Colorants Mode : CMYK Swatch Groups Colorants Type : PROCESS Swatch Groups Colorants Cyan : 0.000000 Swatch Groups Colorants Magenta : 0.000000 Swatch Groups Colorants Yellow : 0.000000 Swatch Groups Colorants Black : 100.000000 Producer : Adobe PDF library 10.01 Slug Family : Eurose Slug Version : 1995 Slug Outline File Size : 0 Slug Kerning Checksum : 0 Slug Foundry : Digital Typeface Corporation Slug Font Kind : TrueType Slug Checksum : 3481574891 Slug Post Script Name : Eurose Slug Font Sense 12 Checksum : 3481574891 Page Count : 2 Creator : Adobe Illustrator CS6 (Macintosh)EXIF Metadata provided by EXIF.tools