Skyscan 86722 Instruction Manual ATOMIC CLOCK WITH OUTDOOR WIRELESS TEMPERATURE

2014-12-11

: Skyscan Skyscan-86722-Instruction-Manual-121422 skyscan-86722-instruction-manual-121422 skyscan pdf

Open the PDF directly: View PDF PDF.
Page Count: 9

LCD1 display
LCD2 display
Hanging holes
Foldable stand
Battery cover
Foldable stand
SKYSCAN ATOMIC CLOCK
WITH OUTDOOR WIRELESS TEMPERATURE
MODEL 86722
Instruction Manual
INTRODUCTION:
Congratulations on purchasing this state-of-the-art Skyscan Atomic Clock as an example of superior design and
engineering. Providing WWVB radio-controlled time, date, time zone, indoor and outdoor temperature display, this
innovative clock is ideal for home or office use. Operation of this product is simple and straightforward. By reading
this operating manual, the user will however receive a better understanding of the Skyscan Atomic Clock together
with the optimum benefit of all its features.
FEATURES:
ATOMIC CLOCK:
WWVB Radio controlled time with manual time setting
12/24 hour time display
Time display: hour, minute, second
Alarm setting with snooze function
Calendar display
Weekday display (3 languages to choose from: English, French and Spanish)
Time zone setting
Daylight savings time ON/OFF option (DST)
ºC or ºF temperature display selectable
Indoor temperature display
Outdoor temperature display via 433MHz transmission
Wall mounting or freestanding
OUTDOOR TEMPERATURE TRANSMITTER:
Remote transmission of outdoor temperature to Temperature Station by 433 MHz signals
Wall mounting case
TO INSTALL AND REPLACE BATTERIES IN THE ATOMIC CLOCK
The Atomic Clock uses 2 x AA, 1.5V batteries. To install and replace the batteries, please follow the steps below:
1. Insert finger or other solid object in the space at the bottom center of the battery compartment and lift up to
remove the cover.
2. Insert batteries observing the correct polarity (see marking).
3. Replace compartment cover.
DO NOT SET THE CLOCK.
Holder
Function keys
TO INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE TRANSMITTER
The transmitter uses 2 x AA,1.5V batteries. To install and replace the batteries, please follow the steps
below:
1. Remove the cover.
2. Insert the batteries, observing the correct polarity (see marking).
3. Replace the battery cover on the unit.
SETTING UP: Do not set the clock until the outdoor temperature is displayed.
1. Slide the battery cover open on the SkyScan Atomic Clock as indicated above (see "To install and replace
batteries in the Atomic Clock“ above).
2. Checking the correct polarization, insert 2 x AA, 1.5V batteries into the battery compartment and replace the
battery cover.
3. Once the batteries are in place, all segments of the LCD will light up briefly. Then the indoor temperature, the
time as -:--, the date as 1.1. , and weekday will be displayed.
IMPORTANT: If the indoor temperature is not displayed after a few seconds, remove the batteries and wait for
at least 10 seconds before reinserting them.
4. Within 2 minutes of activating the SkyScan Atomic Clock, place the batteries into the transmitter (see “To install
and replace batteries in the Temperature Transmitter” above).
5. After a few seconds of inserting the batteries into the transmitter, the Atomic Clock will start receiving data from
the transmitter. The remote temperature will then be displayed on the SkyScan Atomic Clock.
IMPORTANT: if this does not happen after 4 minutes, the batteries will need to be removed from both units and
reset from step 1. Remove the batteries and wait for at least 30 seconds before reinserting them.
6. After the clock receives the outdoor temperature, set your time zone using the manual settings below. The
default time zone is Eastern Standard Time.
7. After the clock receives the outdoor temperature the WWVB time code reception will automatically start. This
reception typically takes between 5-10 minutes in good conditions. If after 10 minutes the WWVB time has not
been received, use the SET key to manually enter the set mode and change either the time or date in order to
activate the WWVB reception (see manual settings below). The clock will then automatically attempt to receive
the WWVB time from 12:00 am through 6:00 am each day (attempts WWVB reception every full hour within
this time frame). When this is successful, the received time will override the manually set time. The date is also
updated with the received time (Please refer to notes on “Radio controlled time” and “Manual time setting”).
Note:
In the event of changing batteries of the unit ensure that the batteries do not spring free from the contacts. Always
wait at least 30 seconds after removing the batteries before reinserting, otherwise start up and transmission problems
may occur.
FUNCTION KEYS
The Atomic Clock has four easy to use keys:
SET key : To enter into the set mode for the following functions: time zone, DST ON/OFF (daylight saving
time), language, hour, minute, year, month, day, weekday, 12/24 hour, ºC or ºF temperature
display
+ key: To toggle between the second, temperature or weekday display
To change any values in manual set mode
ALARM key: To enter into the alarm set mode
To set the alarm ON/OFF
SNOOZE key: To activate the snooze function during alarm
To display the alarm time in normal mode display
To exit the setting modes
Indoor temperature or seconds display
Weekday or seconds display
ATOMIC CLOCK LCD SCREEN DESCRIPTIONS
The Atomic Clock's LCD is divided into 2 sections and once the batteries are inserted, all the segments will light up
briefly before displaying the information for time, date, indoor and outdoor temperatures.
CHANGING THE DISPLAY MODE (DAY, SECONDS, AND TEMPERATURES)
There are three possible display modes to view the day, seconds, and temperatures.
The month&date/weekday/indoor temperature/outdoor temperature is the default.
To change the display:
1. Press the + key. The display should now show the month&date/weekday/seconds/ outdoor temperature.
2. Press the + key a second time and the display will now show the month&date/seconds/indoor
temperature/outdoor temperature.
3. Press the + key third time and the display will return to the normal display.
WWVB RADIO CONTROLLED TIME
The NIST radio station, WWVB, is located in Ft. Collins, Colorado and transmits the exact time signal continuously
throughout the United States at 60 kHz. The signal can be received up to 2,000 miles away through the internal
antenna in the Atomic Clock. However, due to the nature of the Earth’s Ionosphere, reception is very limited during
daylight hours. The Atomic Clock will search for a signal every night when reception is best. The WWVB radio
station derives its signal from the NIST Atomic clock in Boulder, Colorado. A team of atomic physicists continually
measures every second of every day to an accuracy of ten billionths of a second a day. These physicists have created
an international standard, measuring a second as 9,192,631,770 vibrations of a Cesium 133 atom in a vacuum. This
Atomic Clock regulates the WWVB transmitter.
Once the outdoor temperature is displayed on the Atomic Clock, the WWVB tower icon in the clock display will
start flashing in the top center of the LCD. This indicates that the clock has detected a radio signal and is trying to
receive it. When the time code is received, the WWVB tower becomes permanently lit and the time will be
displayed.
If the tower icon flashes, but does not set the time or the WWVB tower does not appear at all, then please take note
of the following:
Recommended distance to any interfering sources like computer monitors or TV sets is a minimum of 6 feet (2
meters).
Within ferro-concrete rooms (basements, superstructures), the received signal is naturally weakened. In extreme
cases, please place the unit close to a window and/ or point its front or back towards the Fort Collins, Colorado,
transmitter.
During nighttime, the atmospheric disturbances are usually less severe and reception is possible in most cases. A
single daily reception is adequate to keep the accuracy deviation below 1 second.
Note:
In case the Atomic Clock is not able to detect the WWVB-signal (disturbances, transmitting distance, etc.), the time
can be manually set (please refer to notes on Manual time setting)
Outdoor
temperature
display
Date
WWVB
time
Alarm icon
Radio reception icon
MANUAL SETTINGS
Note:
If the Atomic Clock has already successfully received the WWVB time signal and displays the correct time
and date, then the Manual settings can be omitted.
After completion of the above described procedures in “Setting up” the manual setting modes can be entered by
pressing the SET key. The following settings can now be programmed:
Time zone setting
DST ON/OFF
Language display setting
Manual time setting
Year setting
Month setting
Date setting
Weekday setting
12/24 hour time display setting
ºC or ºF setting
TIME ZONE SETTING
After entering the manual setting mode as described above, the time zone can be set between the 1 to 12 hour or
Greenwich Mean Time (GMT) range in LCD2. To do this:
OR
1. The time zone (LCD2) will start flashing (Default setting "-5h“). Select the desired time zone by use of the +
key.
Note: The time zones from 4 to 10 hours will be displayed with 3 characters abbreviations:
-4 ATL (Atlantic time),
-5 EST (Eastern time; default time zone),
-6 CST (Central time),
-7 MST (Mountain time),
-8 PST (Pacific time),
-9 ALA (Alaska time),
-10 HAW (Hawaii time).
"GMT” will be displayed if set to GMT (0).
2. Press the SET key to enter the “DST Setting“.
DST SETTING (daylight saving time)
1. The ON digit will start flashing on LCD1. Set the DST ON or OFF by pressing the + key.
2. Press the SET key to enter the “Language Setting“.
Note:
The DST default is “ON”, meaning that the WWVB will automatically change the time according to Daylight
Saving Time in the spring and fall. For areas that do not recognize DST changes (Arizona and parts of Indiana) turn
the DST “OFF”.
LANGUAGE SETTING
The weekdays can be displayed in LCD1 with the pre-set languages: US English, French and Spanish.
1. Set the desired language for the weekday display in LCD 2 by use of the + key.
2. Press the SET key to enter the mode “Manual Time Setting”.
MANUAL TIME SETTING
In case the SkyScan Atomic Clock is not able to detect the WWVB-signal (disturbances, transmitting distance, etc.),
the time can be manually set. The clock will then work as a normal Quartz clock.
Note:
In 12 hours mode the time will be displayed with an additional PM for the time from 12:00 noon until 11:59.
1. The hour digits will start flashing on LCD1. Set the desired hours by pressing the + key followed by pressing the
SET key.
2. Now the minute digits will start flashing. Set the desired minutes by pressing the + key . If the + key is held, the
units will increase by 5.
3. Press the SET key to move to the “Year Setting”.
Note:
The unit will still try and receive the signal every day despite it being manually set. When it does receive the signal,
it will change the manually set time into the received time. During reception attempts the WWVB tower icon will
flash. If reception has been unsuccessful, then the WWVB tower icon will not appear but reception will still be
attempted the following hour.
WWVB time reception takes place from 12:00 am through 6:00 am each day (attempts WWVB reception every full
hour within this time frame). When the time signal is received for example at 1:00 am, the SkyScan Atomic Clock
will not attempt to receive the WWVB signal for the remaining hours until 6:00 am. Therefore, the next signal
attempt will take place between 12:00 am and 6:00 am the next day. The other times WWVB reception takes place,
are upon setup and after manual time set exiting mode. Reception is generally not possible during daylight hours due
to the interference of the sun.
YEAR SETTING
The year can be selected sequentially from 2000 to 2049 and will then start over again (default setting 2000). Only
the last 2 digits of the year will be visible on LCD2.
1. The year digits will start flashing on LCD1. Select the desired year by use of the + key.
2. Press the SET key to switch to the “Month Setting”.
MONTH SETTING
1. The month digits on LCD2 will start flashing. Set the desired month by use of the + key.
2. Press the SET key to move to the mode “Date Setting”.
DATE SETTING
1. The digits for the date will start flashing on LCD2 (Default setting 1). Set the desired date by use of the + key.
Note:
The date can only be set in conjunction with the selected month. For example, it is not possible to set the date
30 if the month of February is selected.
2. Press the SET key to enter the Weekday Setting”.
WEEKDAY SETTING
1. The weekday symbols will be displayed on LCD2 in the pre-set language and flashing. Set the desired weekday
by use of the + key.
2. Press the SET key to enter the mode “12/24 Hours Time Display Setting”.
12/24 HOURS TIME DISPLAYSETTING
1. The “12h” or “24h” will start flashing in LCD1 (Default setting 12h). Select the desired time display mode by
use of the + key.
2. Press the SET key to enter the “ºC/ºF Temperature Setting“.
°C OR °F TEMPERATURE SETTING
1. The characters “°C” or “°F” will start flashing on LCD1 (Default setting °F). By use of the + key select “°C” for
temperature display in degrees Celsius or “°F” for degrees Fahrenheit.
2. Press the SET key to exit the setting mode and switch back to the normal display mode .
EXIT THE MANUAL SETTING MODES
To return to the normal display mode from anywhere in manual setting mode simply press the SNOOZE key
anytime.
If no keys are pressed for at least 15 seconds in setting mode, the Atomic Clock will automatically switch back to
normal display mode.
ALARM SETTING
To enter into the alarm setting mode:
1. Hold the ALARM key for 2 seconds. The hour digits start flashing.
2. Press the + key to set the hour.
3. Press the ALARM key to set the minutes. The minute digits start flashing.
4. Press the + key to set the minutes.
5. Press again the ALARM key to exit the Alarm setting mode or wait for 15 seconds automatic timeout.
TO DEACTIVATE THE ALARM:
The alarm will be automatically ON. To deactivate the alarm (OFF), press once the ALARM key in normal mode
display.
SNOOZE SETTING
The snooze can only be activated during alarm time for a snooze duration of 10 minutes.
OUTDOOR TEMPERATURE TRANSMITTER:
The temperature is measured and transmitted to the SkyScan Atomic Clock every 1 minute. The Atomic Clock will
update the temperature display every 5 minutes.
The range of the Outdoor Temperature Transmitter may be affected by the temperature. At cold temperatures the
transmitting distance may be decreased. Please bear this in mind when positioning the transmitter. Also the batteries
may be reduced in power.
433MHz RECEPTION CHECK FOR OUTDOOR TEMPERATURE TRANSMITTER
The Atomic Clock will receive the temperature data within 4 minutes. If the temperature data is not being received 4
minutes after setting up (the display shows “- - -”), then please check the following points:
1. The distance of the Atomic Clock or Outdoor Temperature Transmitter should be at least 6 feet (2 meters) away
from any interfering sources such as computer monitors or TV sets.
2. Avoid placing the receiver onto or in the immediate proximity of metal window frames.
3. Using other electrical products such as headphones or speakers operating on the same signal frequency (433MHz)
may prevent correct signal transmission and reception.
4. Neighbors using electrical devices operating on the 433MHz signal frequency can also cause interference.
Note:
When the 433 MHz signal is received correctly, do not re-open the battery cover of either the Outdoor Temperature
Transmitter or Atomic Clock, as the batteries may spring free from the contacts and force a false reset. Should this
happen accidentally then reset all units (see Setting up above) otherwise transmission problems may occur.
The maximum transmission range is 82 feet (25 meters) from the Outdoor Temperature Transmitter to the Skyscan
Atomic Clock (in open space). However, this depends on the surrounding environment and interference levels. If no
reception is possible despite the observation of these factors, all system units have to be reset (see Setting up).
POSITIONING
Note:
Before permanently mounting ensure that the Skyscan Atomic Clock is able to receive WWVB signals from the
desired location. Also, extreme and sudden changes in temperature will decrease the accuracy of the Atomic Clock,
and changes in elevation will result with inaccurate temperatures readings for the next 12 to 24 hours. These changes
will require a 12 to 24 hour wait before obtaining reliable data. To achieve a true temperature reading, avoid
mounting where direct sunlight can reach the OutdoorTemperature Transmitter. It is recommended to mount the
Outdoor Temperature Transmitter on a North-facing wall. The maximum transmitting range is 82 feet (25 meters)
obstacles such as walls, concrete, and large metal objects can reduce the range. Place both units in their desired
location, and wait approximately 10 minutes before permanently mounting to ensure that there is proper reception.
Alarm icon
((())) (ON)
POSITIONING THE ATOMIC CLOCK:
There are two possible ways to mount the Atomic Clock:
use of the foldout table stands, or
wall mounting
FOLDOUT TABLE STANDS
The foldout table stand legs are located on the backside, at the lower corners, and on both sides of the
battery cover. The hinges are towards the edges of the SkyScan Atomic Clock, and the ends (with no hinge)
need to be folded out towards the edge. Once the foldout table stands are extended, place the Atomic Clock
in an appropriate location.
WALL MOUNTING
1) Using a straightedge, horizontally space at 3-15/16 of an inch (100.58mm) three screw positions on a
wall.
2) Install three mounting screws (not included) into a wall within transmission rangeleaving
approximately 3/16 of an inch (5mm) extended from the wall.
3) Place the SkyScan Atomic Clock onto the screws, using the hanging holes on the backside. Gently
pull the Atomic Clock down to lock the screws into place.
Always ensure that the SkyScan Atomic Clock locks onto the screws before releasing.
POSITIONING THE OUTDOOR TEMPERATURE TRANSMITTER
The Outdoor Temperature transmitter can be mounted in two ways:
with the use of screws, or
using the adhesive tape.
MOUNTING WITH SCREWS
1) Remove the mounting bracket from the Outdoor Temperature Transmitter.
2) Place the mounting bracket over the desired location. Through the three screw holes of the
bracket, mark the mounting surface with a pencil.
3) Where marked, start the screw holes into mounting surface.
4) Screw mounting bracket onto the mounting surface. Ensure that the screws are flush with the bracket.
MOUNTING WITH ADHESIVE TAPE
1) With a nonabrasive solution, clean and dry the back of the mounting bracket and the mounting
surface to ensure a secure hold. The mounting surface should be smooth and flat.
2) Remove the protective strip from one side of the tape. Adhere the tape to the designated area on
the back of the mounting bracket.
3) Remove the protective strip from the other side of the tape. Position the Outdoor Temperature
transmitter in the desired location, ensuring that the Skyscan Atomic Clock can receive the signal.
TROUBLESHOOTING
Problem:
The LCD is faint.
Solution:
1) Replace the batteries.
Problem:
No reception of WWVB signal
Solution:
1) It may help reception to face the front of the Atomic Clock in the
general direction of Ft. Collins, Colorado.
2) Wait overnight for signal.
3) Be sure the SkyScan Atomic Clock is at least 6 feet (2 meters)
from any electrical devices, i.e. TV sets, computers, or other radio
controlled clocks.
4) Remove batteries for five minutes, reinsert and leave the unit alone
overnight without pressing any keys.
Problem:
Hour is incorrect (minute and date are correct).
Solution:
1) Be sure the correct time zone and daylight saving time are
selected.
Problem:
"OFL“ appears in the indoor temperature section of the LCD
Solution:
1) Move the SkyScan Atomic Clock to an area with warmer or
cooler surrounding temperature. Current surrounding
temperatures are outside measuring range.
Problem:
"--.-" appears in the outdoor temperature section of the LCD.
Solution:
1) Remove the batteries of both units for one minute, then reinsert
them again. Make sure the batteries are new and fresh.
2) Move the Atomic Clock closer to the transmitter or place the
transmitter closer to the Skyscan Atomic Clock. Make sure the
clock is at a receivable range from the transmitter.
3) Move the units to another location. Interferences from other
electrical devices operating on the same signal frequency
(433MHz) may prevent correct signal transmission and reception.
Problem:
"OFL“ appears in the outdoor temperature section of the LCD.
Solution:
1) Wait until the current surrounding temperature cools down or
increases. Current temperature is outside of the measuring range of
the transmitter. The outdoor temperature will be displayed again
once the current surrounding temperature is within the range of the
transmitter.
CARE AND MAINTENANCE:
Avoid placing the units in areas prone to vibration and shock as these may cause damage.
Avoid areas where the units can be exposed to sudden changes in temperature, i.e. direct sunlight, extreme cold
and wet/moist conditions as these will lead to rapid changes, which reduces the accuracy of readings.
When cleaning the LCD and casing, use a soft damp cloth only. Do not use solvents or scouring agents.
Do not submerge the units into water.
Immediately remove all low powered batteries to avoid leakage and damage. Replace only with new batteries of
the recommended size.
Do not make any repairs to the units. Please return it to the original point of purchase. Opening and tampering with
the units may invalidate the warranty.
SPECIFICATIONS:
Temperature measuring range
Indoor: +32ºF to +122ºF with 0.2ºF resolution
0ºC to +50ºC with 0.1ºC resolution
("OFL" displayed if outside this range)
Outdoor: -21.8ºF to +140ºF with 0.2ºF resolution
-29.9ºC to +59.9ºC with 0.1ºC resolution
("OFL“ displayed if outside this range)
Temperature checking interval
Indoor: every 10 seconds
Outdoor: every 5 minutes
Transmission distance: maximum 82 feet (25 meters) in open field, depending upon surrounding structures,
mounting location and possible interfering sources
Power source (Alkaline batteries recommended)
Atomic Clock: 2 x AA, 1.5V batteries
Transmitter: 2 x AA, 1.5V batteries
Battery life: about 12 months
Dimensions (L x W x H)
Atomic Clock: 11.41“ x 0.98“ x 7.48“ / 290 x 25 x 190mm
Transmitter: 2.57“ x 0.9“ x 5.04“ / 40 x 23 x 128 mm
LIABILITY DISCLAIMER:
The manufacturer and supplier cannot accept any responsibility for any incorrect readings and any consequences
that occur should an inaccurate reading take place.
This product is only designed for use in the home or office.
This product is not to be used for medical purposes or for public information.
The specifications of this product may change without prior notice.
This product is not a toy. Keep out of the reach of children
No part of this manual may be reproduced without written authorization of the manufacturer.
WARRANTY:
This product is warranted to be free of defects in manufacturing for 90 days after purchase from Sams Club.
This model is discontinued and not eligible for the manufacturers warranty. Defective clocks should be returned to
the place of retail purchase.
BATTERIES CHANGE:
For best performance, batteries should be replaced at least once a year to maintain the best running accuracy.
Ensure that the batteries used are new and the correct size.
Please help in the preservation of the environment and return used batteries to an authorized depot.
WARNING!
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel cadmium) batteries.

Navigation menu