Skytech II TS-R-2A Fireplace Remote Control User Manual

Skytech II, Inc. Fireplace Remote Control TS R 2 instructions

a href="https://usermanual.wiki/Skytech-II" itemprop="url"> Skytech II >

User Manual

REV 3/3/04Page 1 of 5TS/R-2INSTALLATION AND OPERATING INSTRUCTIONSINTRODUCTIONSKYTECH’S remote wall mount thermostat system was developed to provide a safe, reliable and user-friendly wireless remote wall mountthermostat for gas heating appliances. Battery operation allows the system to operate independently of household current. The systemoperates on radio frequencies with non-directional signals. The SYSTEMS operating range is approximately 20 feet. The system operates onone of 255 security codes programmed at the factory.COMPONENTSTHE SKYTECH TS/R-2 MUST BE INSTALLED EXACTLYAS OUTLINED IN THESE INSTRUCTIONS. READCOMPLETELY BEFORE ATTEMPTING INSTALLATION.FOLLOW INSTRUCTIONS CAREFULLY DURINGINSTALLATION. ANY MODIFICATION OF THESKYTECH TS/R-2 OR ANY OF ITS COMPONENTS WILLVOID THE WARRANTY AND MAY POSE A FIREHAZARD.WALL MOUNT THERMOSTATThe wall/transmitter operates on (2) 3V Button Cell (Included) which powers the LCD screen. Thesebatteries are made specifically for remote controls and electronic lighters. Before using the transmitter the3V batteries must be installed into the battery compartments.It is recommended that ALKALINE batteries always be used for longer battery life and maximumoperational performance.Upon initial use, there may be a delay of five seconds before the remote receiver will respond to thetransmitter. This is part of the system’s design. If the LCD screen will not come on, check the 3V ButtonCell battery.To activate LCD screen install the (2) 3V button cell batteries.The wall thermostat operates on a (2) 3V button cellbatteries (included) made specifically for remote controls.Before using the wall thermostat, install the two (2) 3Vbutton cell batteries. Follow instructions below.First you must remove the face of the thermostat. This isDone by sliding the face up about 1/2” then pull the faceoff the base plate. As shown at the right.TO INSTALL BATTERIES IN THE WIRELESS THERMOSTAT1. Remove face from backing plate and locate the (2) holders for the 3V button cell batteries.2. Slide the button cell batteries into the battery holders. (Make sure that the batteriesare installed with the (+) plus side facing you).TO REMOVE THE BATTERIES IN THE WIRELESS THERMOSTAT1. Remove face from backing plate and locate the (2) holders for the 3V button cell batteries.2. Insert a small screwdriver into the slot above the button cell battery and push the battery out (Slotsshown in picture to the left).ROOM TEMPON OFFSETROOM TEMPTHERMO MODE“SET”ONSETOFFLCDDISPLAYON/UPBUTTONOFF/DOWNBUTTONSETBUTTONTOPTRANSMITTERREMOTE RECEIVERSLIDEBUTTONSREMOTEONOFFSLIDE-ON COVERPLATEREMOTEONOFF2 ea. 12V (A23) Transmitterbattery(included intransmitter)4 ea.WALL-MOUNT COVERPLATE HARDWARE(2) 3V Button Cell Transmitterbatteries (included intransmitter) AA BATTERIES3V3VROOM TEMPONSETOFFSETWIRING KITBACK OF UNIT(2) 3 Volt ButtonCell BatteriesBattery RemovalSlots +PlusSide +PlusSide
REV 3/3/04Page 2 of 5TOPRequires 4-AA 1.5Valkaline batteries(not included)Battery cover slides on/offSlideSwitchONREMOTEOFFWALLPlastic Switch BoxRemote ReceiverCover PlateReceiverSlideButtonTOPREMOTEONOFFWALL MOUNTING THE THERMOSTAT1. The wireless Thermostat must be located within 20’ of the receiver, This is properoperational distance.2. Remove face from backing plate as shown at the start of these instructionsthen locate the (2) two holes that mount the plate to the wall.3. Locate the (2) two mounting holes and mark the holes on the wall.4. Use the (2) two dry wall anchors and screws ( that are supplied) to mountthe base plate to the wall as shown.5. Thermostat can also be mounted onto an existing (Plastic) electrical box.6. Base plate should be mounted level on the wall for best operation.REMOTE RECEIVERIMPORTANT: THE REMOTE RECEIVER SHOULD BE POSITIONED WHERE AMBIENT TEMPERATURES DO NOT EXCEED 130 DEGREE F.The remote receiver (right) operates on four 1.5V AA- size batteries (Included). It is recommended that ALKALINEbatteries be used for longer battery life and maximum microprocessor performance. IMPORTANT: New or fullycharged batteries are essential to proper operation of the remote receiver.NOTE: The remote receiver will only respond to the transmitter when the 3-position slide button on the remotereceiver is in the REMOTE (center) position.The remote receiver houses the microprocessor that responds to commands from the thermostat to control systemoperation. The remote receiver has a 3-position slide switch (see figure at right) for selecting the mode of operation:ON/REMOTE/OFF.• With the slide switch in the ON position (toward the word TOP), the system will remain on until the slide switch is placed in the OFF orREMOTE position. This manual switch will turn ON or OFF the system, without the transmitter or good batteries.• With the slide switch in the REMOTE position (centered), the system will only operate if the remote receiver receives commands from thethermostat. Upon initial use or after an extended period of no use the ON button must be pressed for up to five seconds.• With the slide switch in the OFF position (away from the word TOP), the system is off.• It is suggested that the slide switch be placed in the OFF position if you will be away from your home for an extended period oftime. If the remote receiver is mounted out of children’s reach, placing the slide switch in the OFF position also functions as asafety “lock out” by both turning the system off and rendering the thermostat inoperative.INSTALLATIONNOTE: When the remote receiver is installed as a wall switch, It is recommended that it be installed in a PLASTIC switch box. Remote functions may not operate properly if the remotereceiver is installed in a steel switch box.Make sure the remote receiver switch is in the OFF position (toward the small hole on the receiver’s face). It is recommended that 18 gauge,stranded wires (Included) be used for wire installation between the terminal wiring block on the millivolt gas valve or electronic ignition systemand the wire terminals on the remote receiver. For best results, use 18-gauge wire that has not been spliced and measuring no longer than 20ft.WALL MOUNT Install four 1.5V AA-size ALKALINE batteries (Included) in the remote receiver. For best performance,remote receiver batteries should be factory fresh when installed. Very little battery power is required tooperate the remote receiver, but the electronics are tuned to operate best when battery output is greaterthan 5.3 volts. For new AA batteries should provide an output voltage of 6.0 to 6.2 volts.Position the remote receiver so the word TOP is facing up, then install the remote receiver into theplastic switch box using the two long screws provided. Install the cover plate using the two short screwsprovided.Push the remote receiver slide button over the remote receiver slide switch. Reverse installation of theslide button if it appears off centerWALLROOM TEMPON OFFSET
Download:
Mirror Download [FCC.gov]
Document ID473840
Application IDll1MR6wreWA146J6Be2glg==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize18.62kB (232798 bits)
Date Submitted2004-09-28 00:00:00
Date Available2004-09-27 00:00:00
Creation Date2004-03-12 20:38:16
Producing SoftwareAcrobat Distiller 6.0 for Macintosh
Document Lastmod2004-09-14 12:21:10
Document TitleMicrosoft Word - TS-R-2 instructions
Document CreatorWord: cgpdftops CUPS filter
Document Author: Corbit Beasey
FCC ID Filing: K9LTS-R-2A

Navigation menu