Skytech II TS-R-2A Fireplace Remote Control User Manual TS R 2 instructions
Skytech II, Inc. Fireplace Remote Control TS R 2 instructions
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 473840 |
| Application ID | ll1MR6wreWA146J6Be2glg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 18.62kB (232798 bits) |
| Date Submitted | 2004-09-28 00:00:00 |
| Date Available | 2004-09-27 00:00:00 |
| Creation Date | 2004-03-12 20:38:16 |
| Producing Software | Acrobat Distiller 6.0 for Macintosh |
| Document Lastmod | 2004-09-14 12:21:10 |
| Document Title | Microsoft Word - TS-R-2 instructions |
| Document Creator | Word: cgpdftops CUPS filter |
| Document Author: | Corbit Beasey |
TS/R-2 INSTALLATION AND OPERATING INSTRUCTIONS INTRODUCTION SKYTECH’S remote wall mount thermostat system was developed to provide a safe, reliable and user-friendly wireless remote wall mount thermostat for gas heating appliances. Battery operation allows the system to operate independently of household current. The system operates on radio frequencies with non-directional signals. The SYSTEMS operating range is approximately 20 feet. The system operates on one of 255 security codes programmed at the factory. COMPONENTS T O P TRANSMITTER WIRING KIT ROOM OFF SET TEMP REMOTE RECEIVER SLIDE BUTTONS REMOTE ON SLIDE-ON COVERPLATE ON SET OFF ON 4 ea. 2 ea. OFF 3V 3V AA BATTERIES WALL-MOUNT COVERPLATE 12V (A23) Transmitter battery(included in transmitter) THE SKYTECH TS/R-2 MUST BE INSTALLED EXACTLY AS OUTLINED IN THESE INSTRUCTIONS. READ COMPLETELY BEFORE ATTEMPTING INSTALLATION. FOLLOW INSTRUCTIONS CAREFULLY DURING INSTALLATION. ANY MODIFICATION OF THE SKYTECH TS/R-2 OR ANY OF ITS COMPONENTS WILL VOID THE WARRANTY AND MAY POSE A FIRE HAZARD. (2) 3V Button Cell Transmitter batteries (included in transmitter) HARDWARE WALL MOUNT THERMOSTAT The wall/transmitter operates on (2) 3V Button Cell (Included) which powers the LCD screen. These batteries are made specifically for remote controls and electronic lighters. Before using the transmitter the 3V batteries must be installed into the battery compartments. LCD DISPLAY ROOM “SET” TEMP It is recommended that ALKALINE batteries always be used for longer battery life and maximum operational performance. THERMO MODE Upon initial use, there may be a delay of five seconds before the remote receiver will respond to the transmitter. This is part of the system’s design. If the LCD screen will not come on, check the 3V Button Cell battery. SET BUTTON ON/UP BUTTON SET ON OFF To activate LCD screen install the (2) 3V button cell batteries. OFF/DOWN BUTTON RO The wall thermostat operates on a (2) 3V button cell batteries (included) made specifically for remote controls. Before using the wall thermostat, install the two (2) 3V button cell batteries. Follow instructions below. Battery Removal Slots Plus Side TE MP ON SE OF First you must remove the face of the thermostat. This is Done by sliding the face up about 1/2” then pull the face off the base plate. As shown at the right. BACK OF UNIT Plus Side OM TO INSTALL BATTERIES IN THE WIRELESS THERMOSTAT 1. Remove face from backing plate and locate the (2) holders for the 3V button cell batteries. 2. Slide the button cell batteries into the battery holders. (Make sure that the batteries are installed with the (+) plus side facing you). TO REMOVE THE BATTERIES IN THE WIRELESS THERMOSTAT 1. Remove face from backing plate and locate the (2) holders for the 3V button cell batteries. 2. Insert a small screwdriver into the slot above the button cell battery and push the battery out (Slots shown in picture to the left). (2) 3 Volt Button Cell Batteries REV 3/3/04 Page 1 of 5 WALL MOUNTING THE THERMOSTAT 1. 2. 3. 4. 5. 6. The wireless Thermostat must be located within 20’ of the receiver, This is proper operational distance. Remove face from backing plate as shown at the start of these instructions then locate the (2) two holes that mount the plate to the wall. Locate the (2) two mounting holes and mark the holes on the wall. Use the (2) two dry wall anchors and screws ( that are supplied) to mount the base plate to the wall as shown. Thermostat can also be mounted onto an existing (Plastic) electrical box. Base plate should be mounted level on the wall for best operation. WAL RO OM TE MP ON SE OF REMOTE RECEIVER Requires 4-AA 1.5V alkaline batteries (not included) IMPORTANT: THE REMOTE RECEIVER SHOULD BE POSITIONED WHERE AMBIENT TEMPERATURES DO NOT EXCEED 130 DEGREE F. The remote receiver (right) operates on four 1.5V AA- size batteries (Included). It is recommended that ALKALINE batteries be used for longer battery life and maximum microprocessor performance. IMPORTANT: New or fully charged batteries are essential to proper operation of the remote receiver. Slide Switch TOP ON REMOTE OFF NOTE: The remote receiver will only respond to the transmitter when the 3-position slide button on the remote receiver is in the REMOTE (center) position. The remote receiver houses the microprocessor that responds to commands from the thermostat to control system operation. The remote receiver has a 3-position slide switch (see figure at right) for selecting the mode of operation: ON/REMOTE/OFF. • • • • Ba tt ry co ve sl de on /o ff With the slide switch in the ON position (toward the word TOP), the system will remain on until the slide switch is placed in the OFF or REMOTE position. This manual switch will turn ON or OFF the system, without the transmitter or good batteries. With the slide switch in the REMOTE position (centered), the system will only operate if the remote receiver receives commands from the thermostat. Upon initial use or after an extended period of no use the ON button must be pressed for up to five seconds. With the slide switch in the OFF position (away from the word TOP), the system is off. It is suggested that the slide switch be placed in the OFF position if you will be away from your home for an extended period of time. If the remote receiver is mounted out of children’s reach, placing the slide switch in the OFF position also functions as a safety “lock out” by both turning the system off and rendering the thermostat inoperative. INSTALLATION NOTE: When the remote receiver is installed as a wall switch, It is recommended that it be installed in a PLASTIC switch box. Remote functions may not operate properly if the remote receiver is installed in a steel switch box. Make sure the remote receiver switch is in the OFF position (toward the small hole on the receiver’s face). It is recommended that 18 gauge, stranded wires (Included) be used for wire installation between the terminal wiring block on the millivolt gas valve or electronic ignition system and the wire terminals on the remote receiver. For best results, use 18-gauge wire that has not been spliced and measuring no longer than 20 ft. WALL MOUNT WAL TOP Install four 1.5V AA-size ALKALINE batteries (Included) in the remote receiver. For best performance, remote receiver batteries should be factory fresh when installed. Very little battery power is required to operate the remote receiver, but the electronics are tuned to operate best when battery output is greater than 5.3 volts. For new AA batteries should provide an output voltage of 6.0 to 6.2 volts. ON Receiver Slide Button OFF Remote Receiver Cover Plate Plastic Switch Box Position the remote receiver so the word TOP is facing up, then install the remote receiver into the plastic switch box using the two long screws provided. Install the cover plate using the two short screws provided. Push the remote receiver slide button over the remote receiver slide switch. Reverse installation of the slide button if it appears off center REV 3/3/04 Page 2 of 5 HEARTH MOUNT (bottom view of slide-on cover plate) OFF The remote receiver can be placed on the fireplace hearth or under the fireplace, behind the control access panel, or on any space heating appliance. Position where the ambient temperature does not exceed 130 degrees F. With the battery compartment on the bottom, install the slide-on cover and receiver slide button. Reverse installation of the slide button if it appears off center. ON REMOTE Slide-on cover plate Wire Terminals TOP PROTECTION FROM EXTREME HEAT IS VERY IMPORTANT. Like any piece of electronic equipment, the remote receiver should be kept away from temperatures exceeding 130 degrees F. Battery life is also significantly shortened if batteries are exposed to high temperatures. Remote Receiver Face Plate Receiver Slide Button (back) WIRING INSTRUCTIONS WARNING DO NOT CONNECT REMOTE RECEIVER DIRECTLY TO 110-120 VAC POWER. THIS WILL BURN OUT THE REMOTE RECEIVER AND THE ELECTRONIC MODULE. CONSULT GAS APPLIANCE MANUFACTURER’S INSTRUCTIONS AND WIRING SCHEMATICS FOR PROPER PLACEMENT OF ALL WIRES. ALL ELECTRONIC MODULES ARE TO BE WIRED TO MANUFACTURER’S SPECIFICATIONS THE DIAGRAMS THAT FOLLOW ARE FOR ILLUSTRATION PURPOSES ONLY. FOLLOW INSTRUCTIONS FROM MANUFACTURER OF GAS VALVE AND/OR ELECTRONIC MODULE FOR CORRECT WIRING PROCEDURES. IMPROPER INSTALLATION OF ELECTRIC COMPONENTS CAN CAUSE DAMAGE TO ELETRONIC MODULE. GAS VALVE, AND REMOTE RECEIVER. A qualified electrician or a gas technician who is familiar with the gas appliance and gas valves that will be operated by this remote should install this remote control system. Incorrect wiring connections WILL cause damage to the gas valve or electronic module operating the gas appliance and may also damage the remote receiver. Attach the two 18 gauge wires provided to the receiver as shown. Remote Receiver 2. Tighten screws to hold wires 1. Insert wires into wire terminals WIRING MILLIVOLT VALVES TERMINAL BLOCK ON MILLIVOLT GAS VALVES TH TP TP Installer must connect two 18 gauge wires from the remote receiver to the TH and TH/TP terminals on the millivolt gas valve. (It does not matter which receiver wires are connected to the designated terminals listed above.) TH Operation of the remote receiver is similar to a wall switch in that both turn the gas valve on and off. The remote receiver’s input signals come from the ON/OFF buttons on the transmitter. THERMOPILE/ PILOT LIGHT REMOTE RECEIVER WIRING ELECTRONIC SPARK IGNITIONS ELECTRONIC MODULE TR TH 110/24VAC Transformer neutral wire 24VAC REMOTE RECEIVER Connect the neutral wire from the 24VAC transformer to the TR (transformer) terminal on the ELECTRONIC MODULE. Connect the hot wire from the 24VAC transformer to either of the wire terminals on the remote receiver. Connect another wire (included) between the other receiver wire terminal and the TH (thermostat) terminal on the ELECTRONIC MODULE. hot wire 120VAC REV 3/3/04 Page 3 of 5 GENERAL INFORMATION WALL MOUNT THERMOSTAT OPERATION FUNCTIONS ROOM SET TEMP ROOM SET 1. 2. 3. 4. 5. ROOM TEMP – Current room temperature. F – Degrees Fahrenheit (C Indicates degrees Celsius) FLAME ICON – Indicates APPLIANCE IS ON. SET- Indicates transmitter is in thermostat mode. DASHES – Indicate thermostat mode is being disabled. When transmitter is not in the thermostat mode. The word (SET) will not appear. 1. This TS/R-2 Wall/transmitter has ON, OFF, and SET functions that are activated by pressing the buttons on the face of the transmitter. Upon initial use, there may be a delay of five seconds before the remote receiver will respond to the transmitter. This is part of the system’s design. If the LCD will not come on, check the 3V-button cell battery. TEMP SET OFF ON 2. SETTING MANUAL OPERATION 1. 2. When the ON button on the wall/transmitter is pressed a flame icon on the LCD screen wil appear when the appliance is ON. When the appliance is OFF the flame icon will not appear. TEMP ROOM SETTING THREMOSTAT OPERATION 1. 2. 3. ROOM SET TEMP 4. 5. ROOM SET TEMP If the transmitter is in the thermostat mode the word (SET) will appear on the LCD screen. When the SET button is pressed the temperature digits will begin to flash. While the temperature digits are flashing use the ON button to increase the set temperature or use the OFF button to decrease the set temperature to your desired temperature. When the desired temperature setting is reached press the SET button, again and the word SET will appear on the LCD screen and now the transmitter will automatically send an ON or OFF signal to the receiver. To disengage the thermostat mode push and hold the SET button until (2) dashes appear on the LCD screen. When you release the SET button this will disengage the thermostat mode and the word SET will disappear from the LCD screen. SETTING F / C SCALE The factory setting for temperature is degrees Fahrenheit ( F ) . To change this setting to Centigrade ( C ), you must press and hold both the ON and OFF buttons on the transmitter at the same time until the LCD displays the change. If you want to convert back, repeat the above procedure. BATTERY LIFE Life expectancy of alkaline batteries in the SKYTECH TS/R-2 should be at least 12 months. Replace all batteries annually. When the wall thermostat no longer operates the receiver. Or the remote receiver does not function at all; the batteries should be checked. It is important that the remote receiver batteries are fully charged, providing a combined output voltage of at least 5.3 volts. The length of the wire between the remote receiver and the gas valve directly affects the operating performance of the remote system. The longer the wire, the more battery power is required to deliver signals between the remote receiver and the gas valve. The wall thermostat should operate with as little as 4.0 volts battery power, Measured at the (2) 3 volt button cell batteries. REV 3/3/04 Page 4 of 5
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Modify Date : 2004:09:14 12:21:10+08:00 Create Date : 2004:03:12 20:38:16Z Page Count : 6 Has XFA : No About : uuid:6f5f0b32-7465-11d8-a9fc-000a9574415c Producer : Acrobat Distiller 6.0 for Macintosh Creation Date : 2004:03:12 20:38:16Z Mod Date : 2004:09:14 12:21:10+08:00 Author : Corbit Beasey Creator Tool : Word: cgpdftops CUPS filter Metadata Date : 2004:09:14 12:21:10+08:00 Document ID : uuid:6f5ee8c7-7465-11d8-a9fc-000a9574415c Format : application/pdf Creator : Corbit Beasey Title : Microsoft Word - TS-R-2 instructionsEXIF Metadata provided by EXIF.tools