Sleep Number 3000F Firmness Control™ System 9000 User Manual

Select Comfort Corp Firmness Control™ System 9000 Users Manual

Users Manual

Finding Your Comfort LevelCongratulations on the successful assembly of your foundation. Nowyou are ready to assemble your SLEEP NUMBER®mattress. It can bequickly and easily completed without tools.Sleep Number®9000 Model owners: After completing the foundation assemblyinstructions in the Owner’s Manual, refer to these mattress assembly and FirmnessControl™system instructions instead of those in the Owner’s Manual.Sleep Number®9000 ModelCarefully Check the Contents of Your Mattress BoxesIf you are missing any items listed on thefollowing page, please e-mail Customer Service at customerservice@selectcomfort.comor call 1-800-472-7185.OrientationThese instructions refer to “left” and “right” as if you are standing at the head of the bedlooking toward the foot of the bed. Prepare Your Foam PadsCarefully open the Foam Comfort Pads andFoam Base Pad and set aside. NOTE: At least 20 minutes of expansiontime is needed.before you beginIt is wonderful! Afteronly one night, we bothcommented that we had the best night’s sleep in years! Lowell S.Flagstaff, AZCongratulations on the successful assemblyof your SLEEP NUMBER®bed. Now you are ready to find your comfort level.Firmness Control ™system 9000Unlike innerspring mattresses, a Sleep Number®bed can be personalized at any time to thechanging condition of your body. Somereasons to alter the firmness of your bedinclude:• strained muscles• back pain• weight change• pregnancy• bad sunburnIn addition to personalizing your bed for a great night's sleep, you can also alter themattress firmness when you wake in themorning in order to:• facilitate getting out of bed, if needed• achieve a “fuller” bed appearanceDual AdjustabilityIf you purchased a dual chamber model, youhave the ability to personalize each side of yourSleep Number®bed. Since no two body typesare the same, each sleep partner should findtheir own comfort level. If your model came with one remote for a dualchamber bed, pressing the “L” button on theremote enables you to make changes to theleft side of the bed (left is determined whenlaying on your back on the bed).before you beginNOTE: A 9-volt battery is includedand should last about six months undernormal use. Replace the battery whenthe low battery indicator is displayed.2 Wired RemotesFirmer (top button)Softer (bottom button)Setting Your Sleep Number®STEP 1. Lie on The Sleep Number Bed by Select Comfort™in your normal sleep position, holding your remote. STEP 2. Press any button on the remote to “wake” it up. (If using the wirelessremote with the L and R buttons, press L or R to choose a side.) It willdisplay the current Sleep Number®setting. If you have an idea of whatyour Sleep Number®is, enter it on the remote by pressing the firmer or softer buttons until the number you desire is displayed. The display will go back to your current Sleep Number®and then the adjustmentwill begin. The Sleep Number®and number of reference bars displayedwill change as the firmness changes. Remain still until the change iscomplete. When the adjustment is complete, the Sleep Number®will stay lit for 5 seconds and then the display will turn off.If you decide to change your Sleep Number®before the firmness adjustment is complete, just press anybutton and the Firmness Control™system will stop. Then, go to the Sleep Number®you want. It sometimes takes several nights of sleeping at different settings to discover your ideal Sleep Number®.If you would like to experiment further with your Sleep Number®setting, refer to the inside of page 13 in theOwner’s Manual. Follow the step-by-step instructions for the Deluxe Sleep Number®Firmness Control System™.1 Wireless RemoteFirmer (top button)Softer (bottom button)Firmness Control™system 9000MemoryWireless RemoteRecalling the Memory• Press the “L" or “R" for the side you'dlike to recall. • Press the MEM button 2 times within 5 seconds. The first time you press MEM it will show you the SleepNumber®currently in the memorysetting, the second time it will beginchanging the Sleep Number®to thatmemory setting.Wired RemoteRecalling the Memory• Press the MEM button 2 times within 5 seconds. The first time you press MEM it will show you the SleepNumber®currently in the memorysetting, the second time it will beginchanging the Sleep Number®to thatmemory setting.Fill FeatureThis feature will allow you to inflate one or both chambers to a Sleep Number®of 100.Wireless RemoteTo Fill Both Chambers• Press and hold the FILL button for atleast 2 seconds. The right chamber will fill to 100 then the left chamber will fill to 100.To Fill One Chamber• Press any button to “wake up" the remote.• Press “L" or “R" to determine side to fill.• Press and hold the FILL button for atleast 2 seconds.Wired Remote• On one remote, press and hold the FILL button for at least 2 seconds. Thischamber will begin filling immediately.• To fill the second chamber, on the otherremote, press and hold the FILL buttonfor at least 2 seconds. This chamber willfill to 100 when the first chamber is full.To stop the fill feature at any time, press any button on the remote.Wireless RemoteSetting the Memory • Press the “L" or “R" to choose a side and “wake up” the remote. • Adjust the bed to the Sleep Number®you'd like as your memory setting.• Once at the desired Sleep Number®,press and hold the MEM button for 3 seconds. • “Memory Set" will appear above theSleep Number®when it's set.Wired RemoteSetting the Memory • Press the up or down arrow to “wake up" the remote.• Adjust the bed to the Sleep Number®you'd like as your memory setting.• Once at the desired Sleep Number®, press and hold the MEM button for 3 seconds. • “Memory Set" will appear above theSleep Number®when it's set.Memory Feature moreThis feature allows you to set your favorite Sleep Number®into memory and recall it at any time.Follow these steps to change the memory setting at any time.As the adjustment is taking place, the number displayed and tick marks will indicate the change.▲FillMemoryFillLeft/Right side buttons© 2004 Select Comfort106926 01/04Class B Device Statement: (Section 15.105 (b) of the FCC Rules)“Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant topart 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed andused in accordance with the instructions may cause harmful interference to radio communications. However, there isno guarantee that interference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipment off and on, the useris encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) thisdevice may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may cause undesired operation.Insert2_JR 3/9/04 1:31 PM Page 1
Mattress AssemblySleep Number® Firmness Control™ system(2 wired or 1 wireless)contentsMATTRESS ASSEMBLY▲Position Mattress Covera) Place BOTTOM SECTION of mattress cover (zipper side up) on top of the foundation or bed platform.b) Unzip the top portion and set it aside.c) Holes in the bottom of the cover should be at the head of the mattress and the SLEEP NUMBER®bed label will be at the foot of the mattress.d) Place a Corner Lock™in each corner of the mattress cover.Install Foam Border Wallsa) Place the two long FOAM BORDER WALLSalong the left and right sides of the Mattress Cover. The ends of the Foam Border Walls shouldfit snugly inside the Corner Lock™.b) Place the shorter Foam Border Walls at the head and foot of the bed.c) Make sure the border walls are connected securely and squarely.12345Inflate Air Chamber(s)a) Press any button on the remote to activate the hand control. (If using thewireless remote with L and R buttons, press L or R to choose a side.) Pressthe ∆arrow several times to set the firmness to “20.” Inflation may takeabout 10 minutes.b) For dual chamber models, after the first chamber is inflated, repeat for second chamber. Then, insert the CENTER FOAM WALLbetween the chambers, centering itbetween the head and foot of the bed. c) Zip on the top portion of the bottomsection and now the bottom section is complete.Install Air Chamber(s)a) Lay the AIR CHAMBER(s) in the mattresscover so the Hose Connector(s) are on thebottom and face the head of the bed. b) Connectors will align with the smallopenings at the base of themattress cover. Install Foam Base Pada) Carefully shake out the pad priorto placing in position.b) Place the FOAM BASE PAD insidethe mattress cover with the clippedends at the head of the bed. The pad should nestle inside theFoam Border Walls.Dual chamber model shown.Install Foam Comfort Padsa) Set the DUVET section onto the bottom section with the zipper up. b) Carefully shake out pads prior to placing in position.c) Place the FOAM COMFORT PADS inside the Duvet section (3˝ Intralux™Pad is positioned with the textured side up).Each sleeper can customize their side of the mattress by choosing how to position the foam pads. Place the 1˝ Memory foam pad on top for a more firm,supportive surface. Place the 3˝ Intralux™foam pad on top for a more plush surface.67Final Stepsa) Zip on the duvet cover. b) Move bed to your desired location.You’re Done!On the back you will find more information onusing the Firmness Control™system.QAWhere are the Caps for Air Chamber(s)?The caps are in the Firmness Control™system box.Please store these in case you should ever want todisassemble your bed and temporarily cap your air chamber(s).What if my Foam Comfort Pads appearto be too small or irregular?Gently shake the pads as you place them on yourmattress and they will recover to full size overnight. What do I do if the motor doesn’t run?Make sure the power cord is securely plugged into thepump and the wall outlet. Check to see if the powercord is plugged into an outlet which has power and is not connected to an on/off wall switch.Will my bed deflate if there is a powersurge or power loss?No, your mattress will maintain its firmness. To protectyour Firmness Control™system, we do recommend usinga surge protector.What if I notice a rubber smell from the air chamber?The odor you may smell is non-toxic and will fade over time. To minimize the smell, allow the air chamber to air out for a few hours and then lay a couple of dryer sheets on top of the air chamber.What if I feel like I’m rolling toward the edge or toward the center of the mattress?Although rare, these sensations could potentially beexperienced if one side of the mattress is set quite firmand the other side quite soft. Call Customer Service fora remedy to this situation if it is bothersome to you.If you have any questions along the way, please look for the answer on our Web site: www.selectcomfort.com or call a Customer Service Representative at 1-800-472-7185.If you are missing anyitems, please e-mailCustomer Service atcustomerservice@selectcomfort.com or call 1-800-472-7185.Carefully check the contents of your mattress boxes and compare with the list below. Mattress Cover2 parts• Top section (Duvet)• Bottom sectionComfort Control System™Remote(s)Varies by model. All single chamber models include 1 remote only.Wired remotes will be attached to the Firmness Control™™ system.Foam Border Walls2 long, 2 shortAir Chamber(s)2 for dual chamber models1 for single chamber modelsCenter Foam WallDual chamber models onlyFoam Comfort Pads1 of each for Twin size. 2 of each for Queen and King sizes.• Memory Foam• Intralux™FoamFoam Base PadCaps for Air Chambers2 Packages (Packaged inside the Firmness Control™system box.)Corner Lock™Package of 4Bottom SectionBottom SectionBottom SectionTop Section(Duvet)Top Section(Duvet)Top Section(Duvet)Connect Firmness Control™systema) Place the Firmness Control™system on the floor at the head of the bed. Plug the power cord into the Firmness Control™system and then into an electricaloutlet. (You will hear several clicks indicating there is power.)b) There are two hoses for each air chamber (one large and one small).Pass the end of each hose through the small opening at the base of the Mattress Cover and under the Foam Border Wall to the corresponding chamber.Connect the hose marked with “L” and the adjacentsmaller hose to the left chamber. Connect the othertwo hoses to the right chamber. c) Press hose connections together until they “click.”Note:When flipping thereversible duvet,stand at the sideof the bed and flipfrom side to side.You may need tounzip the Duvetsection andreposition thefoam topper padsso your desiredpad is on top.Insert2_JR 2/23/04 12:10 PM Page 2

Navigation menu