Smarfid Security Equipment LFM Card Reader User Manual 3LEDInstallation Manual RS232 V1 0

Shanghai Smarfid Security Equipment Co, Ltd. Card Reader 3LEDInstallation Manual RS232 V1 0

User Manual

Low Frequency Mullion Mount Reader Installation Manual FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Low Frequency Mullion Mount Reader Installation Manual Mounting: 1. Install the back plate on the wall as shown in the diagram below1. 2. The cover shall clip on the upper edge 2 the push in the bottom part as show in diagram3. 3. Tighten the non-dropout screw, which located underneath of the reader to fix the reader and the back plate4, installation is completed. Specification: Recommendation: 1. Linear DC Power Supply; 2. 22AWG shielded cable; it’s required to do “one-point” ground. (As shown in the diagram) Wiring: Input Voltage (at Reader end) DC9V~15V Typical Read range > 5cm Operating Current 120mA (max) Maximum Cable Length 150m Operating Temperature -30ºC~70 ºC Color Label Description Red +12V dc Power Supply to the reader Black GND Signal GND Green RS232+/RS485+ RS232+/RS485+ White RS232-/RS485- RS232-/RS485- Yellow RED LED RED LED control, active low. Blue Green LED Green LED control, active low Brown Buzzer Buzzer input, active low Grey Tamper Tamper output (open collector, Active low, max 100mA)
Low Frequency Mullion Mount Reader Installation Manual Power up Sequences: 1. When reader is powered up, the reader will flash in Green for 5 seconds . Then the Reader is ready. 2. Blue back lit stays on when the reader is ready. 3. When card is present and read by the reader, blue back lit will flash once; and buzzer will beep once as well. The card data will then transmit to the controller. After, weather the back lit of the reader will remain ON or Flash or change to Green or Red color, this shall depend on the Green and Red LED inputs. Physical Dimension: Troubleshooting: Trouble List Solution No Response when Power Up  Discount the power and confirm that the power supply cable is correctly connected (See “Wiring” above).  Check the input voltage is sufficient (See “Specifications” above). Auto Restart  Check the input voltage is sufficient (See “Specifications” above). Cannot read card number correctly  Check the format setting on the controller if it is the same as the card format. Use approved card (known format and Facility Code) to test.  Check if the shield cable is correctly connected to Classis Ground at ONE point only. Reader beeps but No card data info  Check if data 0 & data 1 cable is correctly connected (See “Wiring” above).  Check the input voltage at the card reader end is correct (See “Specifications” above). Buzzer error  Check if the buzzer cable is correctly connected (See “Wiring” above). Back Lit Error  Check the Led cable is correctly connected (See “Wiring” above).  Use Default Configuration Card to set it back to normal.

Navigation menu