Smarfid Security Equipment LFM Card Reader User Manual 3LEDInstallation Manual RS232 V1 0

Download:
Mirror Download [FCC.gov]
Document ID	1377149
Application ID	3lQTDevDTpQXckPv6hjB2w==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	14.99kB (187395 bits)
Date Submitted	2010-11-16 00:00:00
Date Available	2010-11-16 00:00:00
Creation Date	2010-10-11 14:40:35
Producing Software	AFPL Ghostscript 8.54
Document Lastmod	2010-10-11 14:40:35
Document Title	3LEDInstallation Manual_RS232_ V1 0
Document Creator	PDFCreator Version 0.9.3
Document Author:	Ivey

Low Frequency Mullion Mount Reader Installation Manual
FCC STATEMENT
communications. However, there is no guarantee that interference
1. This device complies with Part 15 of the FCC Rules. Operation is
will not occur in a particular installation. If this equipment does
subject to the following two conditions:
cause harmful interference to radio or television reception, which
(1) This device may not cause harmful interference.
can be determined by turning the equipment off and on, the user is
(2) This device must accept any interference received, including
encouraged to try to correct the interference by one or more of the
interference that may cause undesired operation.
following measures:
2. Changes or modifications not expressly approved by the party
 Reorient or relocate the receiving antenna.
responsible for compliance could void the user's authority to
 Increase the separation between the equipment and receiver.
operate the equipment.
Connect the equipment into an outlet on a circuit different from
NOTE: This equipment has been tested and found to comply with
that to which the receiver is connected.
the limits for a Class B digital device, pursuant to Part 15 of the FCC
 Consult the dealer or an experienced radio/TV technician for
Rules. These limits are designed to provide reasonable protection
help.
against harmful interference in a residential installation.
Operation is subject to the following two conditions:
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
(1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Low Frequency Mullion Mount Reader Installation Manual
Recommendation:
Mounting:
1.
Install the back plate on the wall as shown in the diagram below1.
2.
The cover shall clip on the upper edge
2 the push in the bottom part as show in
1.
Linear DC Power Supply;
2.
22AWG shielded cable; it’s required to do “one-point” ground. (As shown in the diagram)
diagram3.
3.
Tighten the non-dropout screw, which located underneath of the reader to fix the reader and
the back plate4, installation is completed.
Wiring:
Specification:
Input Voltage (at
Reader end)
Operating Current
Operating
Temperature
DC9V~15V
120mA (max)
-30ºC~70 ºC
Typical Read
range
Maximum Cable
Length
> 5cm
150m
Color
Label
Description
Red
+12V dc
Black
GND
Green
RS232+/RS485+
RS232+/RS485+
White
RS232-/RS485-
RS232-/RS485-
Yellow
RED LED
RED LED control, active low.
Blue
Green LED
Green LED control, active low
Brown
Buzzer
Buzzer input, active low
Grey
Tamper
Tamper output (open collector, Active low, max 100mA)
Power Supply to the reader
Signal GND
Low Frequency Mullion Mount Reader Installation Manual
Power up Sequences:
1. When reader is powered up, the reader will flash in Green for 5 seconds . Then the Reader is ready.
2. Blue back lit stays on when the reader is ready.
3. When card is present and read by the reader, blue back lit will flash once; and buzzer will beep once as well. The card data will then transmit to the controller. After, weather the back lit of the reader
will remain ON or Flash or change to Green or Red color, this shall depend on the Green and Red LED inputs.
Physical Dimension:
Troubleshooting:
Trouble List
No Response
when Power Up
Auto Restart
Solution
correctly connected (See “Wiring” above).
Check the input voltage is sufficient (See “Specifications” above).
Check the input voltage is sufficient (See “Specifications” above).
Check the format setting on the controller if it is the same as the card
Cannot read card
number correctly
Discount the power and confirm that the power supply cable is
format. Use approved card (known format and Facility Code) to test.
Check if the shield cable is correctly connected to Classis Ground at
ONE point only.
Reader beeps but
No card data info
Check if data 0 & data 1 cable is correctly connected (See “Wiring”
above).
Check the input voltage at the card reader end is correct (See
“Specifications” above).
Buzzer error
Back Lit Error
Check if the buzzer cable is correctly connected (See “Wiring” above).
Check the Led cable is correctly connected (See “Wiring” above).
Use Default Configuration Card to set it back to normal.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 3
Producer                        : AFPL Ghostscript 8.54
Create Date                     : 2010:10:11 14:40:35+08:00
Modify Date                     : 2010:10:11 14:40:35
Title                           : 3LEDInstallation Manual_RS232_ V1 0
Creator                         : PDFCreator Version 0.9.3
Author                          : Ivey
Subject                         : 

EXIF Metadata provided by EXIF.tools