Smarfid Security Equipment LH3228K Magic Series 13.56MHz&125KHz Reader User Manual Mounting

Shanghai Smarfid Security Equipment Co., Ltd. Magic Series 13.56MHz&125KHz Reader Mounting

User Manual

Manual Keypad & Proximity Flash Mount Reader InstallationMounting:1. Install the metal plate on the wall with two or four screws, which depends on different kinds ofgang box being installed.2. The cover shall clip on the upper edgethe push in the bottom part as show indiagram.3. Tighten the secure non-dropout screw, which located underneath of the reader to fix thereader and the back plate, installation is completed.Specification:Recommendation:1. Linear DC Power Supply;2. 22AWG shielded cable; it’s required to do “one-point” ground. (As shown in the diagram)Wiring:Input Voltage (atReader end)DC9V~15VTypical Readrange> 5cmOperating Current160mA (max)Maximum CableLength150mOperatingTemperature-30ºC~70 ºCNumber padformat4 bits burst by defaultColorLabelDescriptionRed+12V dcPower Supply to the readerBlackGNDSignal GNDGreenData0Wiegand Output data, D0WhiteData1Wiegand Output data, D1YellowRED LEDRED LED control, active low.BlueGreen LEDGreen LED control, active lowBrownBuzzerBuzzer input, active lowOrangeTamperTamper output (open collector, Active low, max 100mA)PurpleDoorbellDoor bell output (open collector, +5Vdc output ≤ 5mA)
Manual Keypad & Proximity Flash Mount Reader InstallationPower up Sequences:1. When reader is powered up, the Green back will flicker for 5 seconds. The reader will beeponce and the reader is in Ready mode.2. Present the card. The Blue LED will flicker once; buzzer will beep once.3. When card is present and read by the reader, blue back lit will flash once; and buzzer willbeep once as well. The card data will then transmit to the controller. After, weather the back litof the reader will remain ON or Flash or change to Green or Red color, this shall depend onthe Green and Red LED inputs.4. For number pad reader, when a number is pressed and successfully detected, the back litunder the number will flash 1 time and the buzzer will beep once. The number being pressedwill burst out by default (4 bits burst).Physical Dimension:Troubleshooting:FCC Caution.§15.19 Labelling requirements.This device complies with part 15 of the FCC Rules. Operation is subjectto the following two conditions: (1) This device may not cause harmfulinterference, and (2) this device must accept any interference received,including interference that may cause undesired operation.Trouble ListSolutionNo Responsewhen Power UpDiscount the power and confirm that the power supply cable iscorrectly connected (See “Wiring” above).Check the input voltage is sufficient (See “Specifications” above).Auto RestartCheck the input voltage is sufficient (See “Specifications” above).Cannot read cardnumber correctlyCheck the format setting on the controller if it is the same as the cardformat. Use approved card (known format and Facility Code) to test.Check if the shield cable is correctly connected to Classis Ground atONE point only.Reader beeps butNo card data infoCheck if data 0 & data 1 cable is correctly connected (See “Wiring”above).Check the input voltage at the card reader end is correct (See“Specifications” above).Buzzer errorCheck if the buzzer cable is correctly connected (See “Wiring” above).Back Lit ErrorCheck the Led cable is correctly connected (See “Wiring” above).Use Default Configuration Card to set it back to normal.KeypadNo ResponsePower off reader for 5 seconds and power on again
Manual Keypad & Proximity Flash Mount Reader Installation§15.21 Information to user.Any Changes or modifications not expressly approved by the partyresponsible for compliance could void the user's authority to operate theequipment.§15.105 Information to the user.Note: This equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates usesand can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correctthe interference by one or more of the following measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.-Consult the dealer or an experienced radio/TV technician for help.

Navigation menu