Smart Technologies and Investment SMARTECSD2707 Wireless Wand KIT User Manual

Smart Technologies & Investment Ltd Wireless Wand KIT

User Manual

GTO Wireless Exit SensorINSTALLATION MANUALKit Includes:• Wirelessvehiclesensorwithdirectburialcoilassemblyandaplug-inelectronics/transmitter moduledesignedformountingupto15feetawayfromthepavementedge.• RB709U-NBtwochannelreceiverwithinstructions.• TwosizeAAbatteries.• GTOWirelessExitSensorinstructionmanualforgeneralinstallationguidance.Rev.01/21/08•PrintedinChinaforGTO,Inc.Signal CableVehicle SensorModule CoverElectronics/TransmitterModuleProgrammableDip SwitchesHow it works:TheGTOwirelessexitsensorconsistsofavehiclesensor,transmitter,andprogrammabledipswitches.Themaximumrangebetweentransmitterandreceiveris80-100ft.ThetransmittermoduletransmitsaspecialGTOtransmittercodewithadditionalinformationtotellthereceiverthatthisdeviceshouldbetreatedasa“freeexit”device.ThelatestGTOgateoperatorswithbluecontrolboards(GTO“GEN3”)areabletodecodethisformatandrecognizethedeviceasafreeexitoropenonlycommandwithouttheuseoftheRB709U-NBreceiver.Thiswillsimplifyinstallationssoonlytheoriginalreceiverwillberequired.TheRB709U-NBreceiverwillberequiredunlessyouhavetheGEN3(blueboard).TheRB-709U-NBhastwochannelsthatcanbeprogrammedtooperatearemotetransmitterorkeypadandwirelesswand.Forinstance,Channel1couldbewiredtotheCycleandCOMaccessoryterminalsandcouldbeprogrammedtooperateatransmitterandkeypad.Channel2couldbewiredtotheExitandCOMaccessoryterminalsandcouldbeusedtooperatethewirelessexitsensor.Dependingonthefrequencyofuse(vehicletrafc)thetwoAAbatterieswilllastabout1to3years.Thank you for purchasing the GTO Wireless Exit Sensor. Please read the directions carefully and completely before installing.For more information on GTO's full line of automatic gate openers and access controls visit our website at www.gtoaccess.comGTO WIRELESS EXIT WANDTRANSMITTERCODE TRANSMITACTIVEMIN MAXSENSITIVITYGTO WIRELESS EXIT WANDTRANSMITTERCODE TRANSMITACTIVEMIN MAXSENSITIVITY
2 Wireless Exit SensorAbove is a typical location where installing a conventional “wired” exit sensor would require cutting and trenching across more than 50 feet of asphalt driveway.Gate Opener ReceiverDrivewayTransmitter100’ MaxWirelessRANGE:12 ft. radius (max)SENSOR:2 feet fromdriveway (max)and 12” deepOpen Gate OutsideSensor Range25 ft. from gate (min)Sensor and Module Placement Overview• DeterminetheoptimumlocationfortheVEHICLESENSORusingtheinformationfoundabovein“Sensorand TransmitterPlacementOverview”.Thendigaholeapproximately10-12inchesdeepand24incheslongwithin 2feetandparalleltotheedgeofthedriveway.Next,digatrenchnomorethan15ftfromthisholetothelocation whereyouwillinstallthetransmittermodule.KeeptheVEHICLESENSORandthecableuncoveredatthistime.IMPORTANT: Clear an area 20 feet in all directions of metal tools, toys and automobiles, to prevent magnetic disturbance during testing and installation.Sensor PlacementDetermining Sensor LocationFor Optimum Performance:•LocatetheSENSORasfaraspossibleawayfrompowertransformers,powerlines,underground gasline,andtelephonelines.•LocatetheSENSORawayfromgeneralmovingtrafctopreventunwantedactivation.Remember thattheSENSORdetectsMAGNETICDISTURBANCEScausedbyavehicle’smassandvelocity.•Rangedistanceisapproximateandwillvaryduetooutsideinterference,typeofsoil,vehiclemass, speed,etc.•ItisrecommendedthatyouruntheSignalCableinsidePVCconduittopreventaccidentaldamage.•DonotrunSignalCableinconduitwithotherwiressuchasACpowerorothercontrolwires.•TheSIGNALCABLECANNOTBESPLICED.Ifyouneedmorewire,contacttheGTOSales  Departmentat1-800-543-GATE(4283).NOTE: Place the transmitter on the same side of the driveway in the line of sight of the receiver to maximize the range.
Wireless Exit Sensor 3ReceiverTransmitterModuleDriveway 10 -12 inch deep pit15 ftmaximumVehicle Sensor100 ftMaximumInstall the Vehicle Sensor DO NOT fill the hole until final testing is complete.• Digasmallpitabout10-12inchesdeepclosetotheedgeofyourdriveway.Theholeshouldallowyoutolay theVehicleSensoratinthebottomwiththelengthoftheVehicleSensorparalleltothedirectionofthedriveway.• Afterlayingthevehiclesensorintheholeadjacent tothedriveway.Runthesignalcabletothe transmittermoduleinthenarrowtrench.Do not fill the hole or trench until satisfactory operation is verified.Vehicle Sensor10-12 inchdeep pitPlaced 2 ft maximumfrom edge of drivewayVehicle Sensor shouldlay parallel to drivewayDRIVEWAYTransmitter Module PlacementDetermining Transmitter Module Location• Choosealocationforthetransmittermodulethatisfarenoughfromthedrivewayedgethatvehiclesare  unlikelytohitit.Fifteenfeetofwireisincludedtoallowthetransmittertobe12to15feetfromthedriveway. Totestthechosenlocationtobesureitisfreefromobstructionsorotherinterference,youcanuseyour  remotecontroltransmitteratthesameheightasthetransmittermoduletoactivatethegate.
4 Wireless Exit Sensor6 inchesdeepSensorNOTE: DO NOT place in the direct path of a sprinkler. The module is water resistant but not waterproof.• DiganarrowtrenchorslitfromtheVehicle Sensortothetransmitterlocationusingaat spadeorothertool.Thewirefromthewandto thetransmittershouldbeatleastsixinches  deeptoavoidpossibledamagefromedgers, orlawnaerators.GTO WIRELESS EXIT WANDTRANSMITTERCODEMEDTRANSMITACTIVEMIN MAXSENSITIVITY• FeedtheSignalCablethroughthePVCpipe andplugintotheconnectoratthebottomof theElectronics/Transmittermodule.Connecting the Electronics/Transmitter ModuleInstall the Electronics/Transmitter Module
Wireless Exit Sensor 5GTO WIRELESS EXIT WANDTRANSMITTERCODEMEDTRANSMITACTIVEMIN MAXSENSITIVITYNOTE: The module should extend out at least 12” above ground.• InstallandconnecttheRB709U-NBreceivertoyourgateoperatorasshownintheinstructionssuppliedwith  thatreceiver.YoucanskipthisstepifyouhaveaGTOGEN3controlboardonyourgateoperator.• IfusingtheRB709U-NBreceiver,itisrecommendedthatyoudisconnecttheoriginalantennareceiverthat  camewithyourgateopener.• RemovetheoutercoverfromtheElectronics/TransmitterModule.• SetthetransmitterDipSwitches.IfyouhaveGTOhandheldtransmittersforyourgate,settheDipSwitchesin theTransmitter/ModuletothesamesettingsastheDipSwitchesinyourtransmitter.IfyoudonothaveGTO transmitters,settheDipSwitchestoanydesiredsetting.Wedonotrecommendusingthefactorycode  settingasshipped.• Setthesensitivitycontroltomidscale(mediumsensitivity).• DONOTinstallthebatteriesatthistime!GTO WIRELESS EXIT WANDTRANSMITTERCODEMEDTRANSMITACTIVEMIN MAXSENSITIVITYSensitivityPotentiometerDip SwitchesTransmit Indicator• SecuretheElectronics/TransmitterModuleon thesuppliedPVCpipebyburyingthebottomthird ofthepipeinthesoilandtampingtheground aroundthepipe.DONOTcovertheelectronics modulewithametalcoverasthiswillcause signalinterference.• Thiscompletesthehardwareinstallation.Electronics/Transmitter Module SetupPlanting the Electronics/Transmitter Module
6 Wireless Exit SensorTo use or not to use the Included ReceiverDependingonthetypeofcontrolboardyouareusingyoumayormaynotneedtousetheRB709U-NB universal receiverincludedwiththeWirelessExitSensor.• Post mount operators with a GEN-3 Blue Control Board DO NOT require that you use the RB709U-NB universal receiver.(SeethepicturesbelowtodetermineifyouhaveaGEN-3BlueControlBoard).• ALL PAD MOUNT OPERATORS will require the use of the RB709U-NB universal receiver.1 2 3 4ON DIPSTATUSLEARN RMTLEARNMAST LIMIT LEARNSLV LIMIT S3S4S2OFFSOFT START OFFWARNING OFFOPEN PULLSLV OPEN DLY.MODE1 OFFMODE2 OFFONONPUSHSIMULT.ONON120 MIN MAXAUTO CLOSE TIME STALL FORCEGEN-3 Blue Control BoardDOESNOTrequiretheRB709U-NBuniversalreceiver
Wireless Exit Sensor 7Programming the Exit Sensor’s Transmitter CodeBeforeuse,thereceiverneedsto“learn”thecodetransmittedbythewirelessexitsensor.Thissimpleproceduretakesonlyafewminutes.• Gen3(blueboard)instructions Setthe9DipSwitchesintheTransmitterModuletothesamesettingsasthe9DipSwitchesinthe GTORemoteTransmitter.TheGen3(blueboard)willautomaticallyrespondtothewirelessexitsensor’s transmissionasafreeexitoropenonlycommand.• ForoperatorsWITHOUTtheGen3(blueboard) Disconnectthered,blackandgreenwiresfromtheoriginalreceiveratthereceiverterminalsonthegate  opener’scircuitboard.Itwillnolongerbeneeded.WireChannel1(greenandbluewires)ontheRB709U-NBtotheCycleandCOMaccessoryterminalsonthegateopener.Holddownthegateopener’sremotetransmitterbuttonandtheChannel1buttonontheRB709U-NBatthesametime.TheredlightontheRB709U-NBshouldblinkoncein1to2secondstoindicatethatthereceiverhaslearnedthecodefromtheexitsensor.WireChannel2(yellowandbrownwires)ontheRB709U-NBtotheExitandCOMterminalsonthegateopener.InstallthetwoAAbatteriesinthewirelessexitsensor’stransmittermodule.Thiswillimmediatelystart30secondsoftransmissionsfromthewirelessexitsensor.Whiletheexitsensoristransmitting,holddowntheChannel2buttonontheRB709U-NB.TheredlightontheRB709U-NBshouldblinkoncein1to2secondstoindicatethatthereceiverhaslearnedthecodefromtheexitsensor.Transmitter ModuleDip SwitchesSetSameAsGTORemoteTransmitterDipSwitchesRemote TransmitterDip SwitchesSetSameAsTransmitterModuleDipSwitchesPRO3040-PCB Connections GTO/PRO1000, SL1000/2000 ConnectionsONALARM ACCESSORY RCVRSEQ1SEQ2LEARNBLUORGWHTGRNR B GCH 1 (Green Wire to Grn)CH 1 (Blue Wire to Blu)CH 2 (Yellow Wire to Grn)CH 2 (Brown Wire to Wht)CH 1 (Green Wire to Com)CH 1 (Blue Wire to Cycle)CH 2 (Yellow Wire to Exit)CH 2 (Brown Wire to Com)RECEIVERCOM COMCYCLECLOSESAFETYEXIT/OPENSHADOWLOOPCLOSEEDGEOPENEDGEBLKGRN REDSTALL FORCEMINMAXGTO WIRELESS EXIT WANDTRANSMITTERCODE TRANSMITACTIVEMIN MAXSENSITIVITY+0ECE 1 2 3 4 5 6 7 8
8 Wireless Exit SensorFCCWARNING:Changesormodicationstothisunitnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser’sauthoritytooperatetheequipment.NOTE:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,usesandcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurinparticularinstallations.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:•Reorientorreplacethereceiverantenna.•Increasetheseparationbetweentheequipmentandthereceiver.•Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.•Consultthedealeroranexperiencedradio/TVtechnicianforhelp.Normal OperationAfterthe30secondsof“learnmode”transmission,theVehicleSensorperformsaninitialcalibrationsequence.Calibrationlastsabout15seconds.DONOTmovethesensor,anyvehicles,orlargemetalobjectsneartheVehicleSensorduringthis15secondperiod.Learningandcalibrationisnowcomplete.TesttheVehicleSensorbydrivingavehiclealongthedrivewayatanormalspeedforthedriveway(5-15mph).Thegateshouldopenreliablywhenrepeatedseveraltimes.Iftheexitsensordoesnotopenthegateeverytime,tryincreasing(clockwiserotation)thesettingofthesensitivitypotentiometer.Whenoperationissatisfactory,installtheoutercoverovertheElectronics/TransmitterModule,lltheholeandtrenchwithsoilandtamprm.Don’tbealarmedifyourgateopenswhileyouarellingthetrenchandhole.Themetalinyourshovelisactivatingtheexitsensor.Thisproductandanyaccessoryyoupurchaseshouldonlybeinstalledonagateopenerthatmeetsthecurrentsafetystandard,UL325,4thEdition.IfyouhaveagateopenerthatisnotlistedwiththecurrentstandardpleasecontacttheGTOsalesdepartmentforconsultationonagateopenerthatcanmeetyourspecicneeds.GTO WIRELESS EXIT WANDTRANSMITTERMIN MAXSENSITIVITY
Wireless Exit Sensor 9GTO Limited One Year Warranty GTO,Inc.,gateopenersandaccessoriesarecoveredunderwarrantybythemanufactureragainstdefectsinmaterialsandmanufacturerworkmanshipforaperiodofone(1)yearfromdateofpurchase,provided the recommended installation procedures have been followed.Inthecaseofproductfailureduetodefectivematerialormanufacturerworkmanshipwithintheone(1)yearwarrantyperiod,theproductwillberepairedorreplaced(atthemanufacturer’soption)atnochargetothecustomer,ifreturnedfreightprepaidtoGTO,Inc.,3121HartseldRoad,Tallahassee,Florida,USA32303.IMPORTANT:Call(800)543-1236foraReturnGoodsAuthorization(RGA)numberbeforereturningaccessorytofactory.ProductsreceivedatthefactorywithoutanRGAnumberwillnotbeaccepted.Replacementorrepairedpartsarecoveredbythiswarrantyfortheremainderoftheone(1)yearwarrantyperiodorsix(6)months,whicheverisgreater.GTO,Inc.willpaytheshippingcharges(equaltoUnitedParcelServiceGROUNDrate)forreturntotheownerofitemsrepairedunderwarranty.Themanufacturerwillnotberesponsibleforanychargesordamagesincurredintheremovalofthedefectivepartsforrepair,orforthereinstallationofthosepartsafterrepair.Thiswarrantyshallbeconsideredvoidifdamagetotheproduct(s)wasduetoimproperinstallationoruse,connectiontoanimproperpowersource,orifdamagewascausedbylightning,wind,re,ood,insectsorothernaturalagent.Aftertheone(1)yearwarrantyperiod,GTO,Inc.willmakeanynecessaryrepairsforanominalfee.CallGTOat(800)543-1236formoreinformation.Thiswarrantygivesyouspeciclegalrights,andyoumayalsohaveotherrightswhichmayvaryfromstatetostate.Thiswarrantyisinlieuofallotherwarranties,expressedorimplied.NOTE: Verification of the warranty period requires copies of receipts or other proof of purchase. Please retain these records.GTO,Inc.•3121HartseldRoad•Tallahassee,Florida323031-800-543-GATE(4283)•TechnicalSupport1-800-543-1236www.gtopro.comWhenanEXITSENSORisinuse,theautomaticgateopenercouldbeactivatedbyachildonabicycle,tricycleorothermetalplayequipment.Thisproductisnotrecommendedforapplicationsexposedtochildren.WARNINGTechnicalSupportHours:MON-FRI8:00AM-7:00PM(ET)(800) 543-1236(850) 575-4144
Page 26Smart Technologies & Investment Ltd. Wireless Wand KIT FCC ID:N9KSMARTECSD2707 NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

Navigation menu