SmartLabs 26742 LED PAR38 Light Bulb User Manual
SmartLabs, Inc. LED PAR38 Light Bulb Users Manual
Users Manual
® INSTEON LED Bulb (PAR38) 2674-222 Contents Getting Started INSTEON LED Bulb Device Overview Do Not Connect to a Dimmer Leave Your Fixture On Linking INSTEON Links Understanding Linking Linking to the INSTEON Hub using the iOS or Android App Linking with a Single-Button Controller Linking with a Multi-Button Controller Multi-Linking or Making a Scene Unlinking from a Single-Button Controller Unlinking from a Multi-Button Controller Multi-Unlinking or Removing a Scene 10 11 12 13 14 Software-Only Features Ramp Rate 16 Disable Linking on Power-up Always-On Wiring Always-On Wiring 18 Appendix Troubleshooting Product Warranty 22 24 25 26 Getting Started Everything you need to quickly get up and running. INSTEON LED Bulb Device Overview INSTEON ID Leave Your Fixture On Do Not Connect to a Dimmer Linking Your LED Bulb does not have a set button. with the LED Bulb is lost. ON INSTEON Links INSTEON devices can stand alone and function as a local switch or dimmer, but their real power comes when they are connected together to form a control system. Most INSTEON devices can control one another and be the recipient of control. The process of associating multiple INSTEON devices to one another is called linking. Understanding Linking Links are One-Way Links Remember a Device’s State The current state of the controlled device is 75% ® Switch A will turn Switch B on and off but Switch B cannot turn Switch A on or off. Switch Lamp Dimmer 75% brightness. Controllers Responders on or off are called controllers. controller are called responders. ® On Neutral Off Set ® Load L1 Line ® ® Understanding Linking Controller-Only Responder-Only other devices. ® Motion Sensor Dimmer Switch LED Bulb Dimmer Switch responders to devices and scenes. Sensor. Grouping Devices Use Cross Linking each direction. cross linking. Load control one another and the connected Link Switch A to Switch B and repeat to link Switch B to Switch A. Linking to the INSTEON Hub using the iOS or Android App Tap the Add button. All Devices Rooms All Devices Check-In Favorites Back Door Bathroom Bedroom Bathroom Bedroom Hallway Font Door Garage Door Garage Light Kitchen Living Room Outside Motion Sensor Outside Lights 72º 72º Add devices. and screw in the LED Bulb. The Bulb Add Device LED Bulb Thermostat Door Sensor Open/Close Sensor You can now control your LED Linking with a Single-Button Controller and hold the set button until the device beeps. then screw in the LED Bulb. Your now control your LED Bulb. Linking with a Multi-Button Controller the desired control button and then press and hold the set button until the device beeps. then screw in the LED Bulb. Your now control your LED Bulb. 10 Multi-Linking or Making a Scene and hold the set button until the button. 50% 72% LED Bulb LED Bulb 30% ON Appliance and hold the set button until they Tap the set button on your building your scene. now control your scene. 11 Unlinking from a Single-Button Controller and hold the set button until the device beeps. again until the device beeps. then screw in the LED Bulb. Your longer control your LED Bulb. 12 Unlinking from a Multi-Button Controller the desired control button and then press and hold the set button until the device beeps. again until the device beeps. then unscrew and reinsert the LED beep. longer control your LED Bulb. 13 Multi-Unlinking or Removing a Scene and hold the set button until the button. Tap the set button on your ® ® 14 Software-Only Features Most INSTEON devices contain features that can only be enabled, 15 Software-Only Features Ramp Rate Disable Linking on Power-up Customize the speed at which the LED Bulb fades on or off. Default is 0.5 seconds, maximum duration of 8 minutes. Prevents LED Bulb from entering linking mode each time power is disconnected and reapplied. Default is off. Instant LINKING 0.5 Seconds 2 Seconds 5 Seconds 15 Seconds 16 Always-On Wiring controlled by a wall switch, you might consider wiring that wall switch as power. Replacing the wall switch with an INSTEON Switch will provide full control for any INSTEON device in your home. 17 Always-On Wiring Turn off power to your switch at the electrical service panel. contact support. ON ON ON ON OFF ON ON or Neutral Wire ON ON ON Circuit Breakers not used and, instead, capped. Verify that the wire nuts are secure and that no exposed copper wire is visible except for the bare ground wire. Load Neutral Line Ground 18 Always-On Wiring left and turn power on to the switch at the circuit breaker panel. press and hold the set button until the device beeps. Test your switch by tapping the paddle not change but the status lights on the switch will. and reinsert. Your LED Bulb will Your switch will now control your LED Bulb 19 Appendix Everything else you might need to know about your INSTEON product. 20 INSTEON Glossary Controller Blinking LED turning on and off repeatedly The speed at which the load fades on or off The preset brightness level a device will return to when turned on Link A one way association between a controller and responder Linking Unlinking / Unlinking Load Scene Set Button nodes can join the network without any installation procedure. X10 21 General Brand 813922013672 US Warranty INSTEON Features Yes Yes No Yes 400 Begin Brighten End Brighten Beep 400 No Yes 22 Operation 880 83.40 Status LED None 32 Mechanical Installation Color White Weight 183g Indoors Electrical Supply Voltage Local Control No <0.75 Watt 23 Troubleshooting LED Bulb won’t link to other INSTEON Devices Try this: • • • LED Bulb is slow to respond Bulb. Try this: • their links using the standard unlinking procedure. • properties. LED Bulb turned on or off by itself Try this: • I want to factory reset my LED Bulb Try this: • 24 warranty 25 Product Warranty Limited Warranty Limitations 26
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf Linearized : No XMP Toolkit : XMP Core 5.1.2 Creator Tool : Adobe InDesign CS6 (Macintosh) Metadata Date : 2013:11:01 08:56:16-07:00 Create Date : 2013:11:01 08:56:02-07:00 Modify Date : 2013:11:01 08:56:16-07:00 Format : application/pdf Original Document ID : xmp.did:068011740720681192B0FBEB861CEBEF History Software Agent : Adobe InDesign CS6 (Macintosh) History Parameters : from application/x-indesign to application/pdf History Changed : / History When : 2013:11:01 08:56:02-07:00 History Action : converted Instance ID : uuid:bc1a85a0-facd-4e4b-bebc-2af6bc77293b Document ID : xmp.id:F77F117407206811822AC0A5D17589B2 Derived From Rendition Class : default Derived From Document ID : xmp.did:068011740720681192B0FBEB861CEBEF Derived From Instance ID : xmp.iid:6CD19EBD07206811822AD1C0EDDA6628 Derived From Original Document ID: xmp.did:068011740720681192B0FBEB861CEBEF Rendition Class : proof:pdf Trapped : False Producer : Adobe PDF Library 10.0.1 Has XFA : No Page Count : 26 PDF Version : 1.4 Creator : Adobe InDesign CS6 (Macintosh)EXIF Metadata provided by EXIF.tools