Snap On 870016 Users Manual

870016 Snapon-18Ga-Brad-Nailer_870016_eng

2015-02-05

: Snap-On Snap-On-870016-Users-Manual-359060 snap-on-870016-users-manual-359060 snap-on pdf

Open the PDF directly: View PDF PDF.
Page Count: 14

DownloadSnap-On Snap-On-870016-Users-Manual-  Snap-on-870016-users-manual
Open PDF In BrowserView PDF
MODEL #870016

18 GAUGE 1-1/4" BRAD NAILER
INSTRUCTION MANUAL

FOR CUSTOMER SERVICE
PARA EL SERVICIO
PARA EL CONSUMIDOR

1-888-278-8092
Printed in Taiwan

SNAP-ON ® IS A TRADEMARK LICENSED BY SNAP-ON ® CORP.,
U.S.A., WHICH DOES NOT MANUFACTURE OR
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
©COPYRIGHT 2007 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
870016 – 18 Gauge 1 1/4" Brad Nailer _Rev 9/6/07

THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO SO
COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR SNAP-ON PRODUCT, DO
NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT AT
1-888-278-8092. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE: MODEL No.,
DATE PURCHASED AND STORE LOCATION.

TABLE OF CONTENTS
CONGRATULATIONS! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS . . . . . . . . 2-3
IMPORTANT INFORMATION ABOUT THIS MANUAL . . . . . . . . . . . 4
SAFETY WARNINGS AND PRECAUTIONS . . . . . . . . . . . . . . . . . . . 4-7
FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
COMPONENT INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
OPERATING THE BRAD NAILER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13
SELECT TRIGGER ACTUATION MODE . . . . . . . . . . . . . . . . . . . . . . 9-10
ADJUSTING DEPTH OF NAILING . . . . . . . . . . . . . . . . . . . . . . . . . . 11
USING THE HOOK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
LOADING NAILS INTO THE AIR NAILER . . . . . . . . . . . . . . . . . . . . 12
USING THE NO-MAR NOSEPIECE . . . . . . . . . . . . . . . . . . . . . . . . . 12-13
REQUIRED DAILY PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14
USING THE AIR NAILER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-15
CHANGING DIRECTION OF EXHAUST AIR . . . . . . . . . . . . . . . . . . . 15
CLEARING JAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-16
MANDATORY MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-18
PARTS DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-22
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1 YEAR LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-26

CONGRATULATIONS!
Thanks for choosing this product. Our aim is to provide you with the highest quality products, and we want you to be totally satisfied with your product and our Customer Service.
If any help or advice is needed, please contact us at 1-888-278-8092. When properly
cared for, this product will give you many years of satisfaction.
GENERAL SAFETY RULES
READ AND FOLLOW ALL INSTRUCTIONS. Failure to follow all instructions in this manual may result in severe personal injury or death.
Keep this manual and refer to it for Safety Instructions, Operating Procedures,
and Warranty.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS
The safety instructions provided in this manual are not intended to cover all possible
conditions and practices that may occur when operating, maintaining and cleaning
power tools.
Always use common sense and pay particular attention to all the DANGER,
WARNING, CAUTION and NOTE statements of this manual.
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.

1

2

CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
NOTE provides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.

IMPORTANT INFORMATION ABOUT THIS MANUAL
Improper maintenance and operation are responsible for the majority of accidents
involving brad nailers. The largest portion of these could be prevented by recognizing the basic safety rules and precautions. Most accidents can be avoided if the
operator recognizes a potentially hazardous situation before it happens and by
observing appropriate safety rules and procedures as outlined in this manual.
Basic safety precautions are outlined in the SAFETY portion of this manual and
throughout text in this manual where a potential hazard might occur.

In addition to SAFETY ALERTS listed above, there could also be numerous symbols
alerting the operator that specific safety equipment is required to safely operate this
tool. Learn these SAFETY SYMBOLS as well as the SAFETY ALERTS to prevent
injury to the operator and to bystanders.
READ OPERATING INSTRUCTIONS: Read and understand tool labels,
safety warnings and precautions in this manual before operating the tool.
Failure to follow WARNINGS could result in serious injury or even death
to the operator or bystanders.

Hazards that MUST be avoided to prevent serious injury follow headers marked
DANGER or WARNING. These same precautions are placed as labels on the tool
itself.
NEVER use this nailer for applications that are NOT specified in this manual.
SAFETY WARNINGS AND PRECAUTIONS

WEAR APPROVED EYE PROTECTION: Safety glasses must conform to
the requirements of American National Standards Institute (ANSI) Z87.1
and provide protection against flying particles from both front and side.

Do not operate brad nailer anywhere fastener may contact hidden electrical
wiring. Contact with a “live” wire will make all metal parts of the brad nailer
“live.” This can result in severe electrical shock, severe burns or death to the
operator. Contact a qualified electrical contractor to ensure a safe working environment exists.

WEAR HEARING PROTECTORS: Hearing protectors should be worn to
protect the ears from loud exhaust noise produced by the air tools.

Be aware of conduits or gas pipes. Striking a gas pipe could result in an explosion causing serious injuries or even death to the operator or bystanders.

USE ONLY CLEAN, DRY COMPRESSED AIR: Never use oxygen, combustible gases and any other bottled gas to operate air tools. Using these
other sources can cause the air tool to explode.
NEVER POINT THE BRAD NAILER AT YOURSELF OR OTHERS: Fasteners
are under extreme pressure and can cause severe injury or even death if
misused.
DO NOT EXCEED 120 psi (8.43 kg/cm2G). Using excessive pressure
from the power source can cause the brad nailer to explode resulting in
severe injury or even death to the operator or bystanders.

3

Be aware of what is behind the work piece. A fastener could travel through the
work piece and out the other side, striking a bystander resulting in serious
injury or even death.
Do not operate the brad nailer in the presence of flammable liquids, such as
gasoline, thinner, paint, or adhesives, gases or dust. Sparks created by the tool
can cause flammable materials to ignite or explode. Failure to comply with this warning could result in serious injury or even death to the operator.
Keep bystanders, children and visitors away from area where brad nailer is
being used. Distractions can result in severe injury or even death to anyone
who inadvertently gets in the way of nailing operations.
Do not use oxygen, combustible or bottled gases (such as carbon
dioxide or nitrogen) as a power source for the brad nailer. Use
only compressed air from a source as outlined in this manual. The
tool will explode resulting in severe injury or even death to the operator and
bystanders.

Do not connect brad nailer to an air source capable of generating
more than 200 psi (14.06 kg/cm2 G). Over-pressurizing the brad
nailer will result in bursting, abnormal operation or breakage of the
tool. Use only clean, dry, regulated compressed air at levels specified on the tool. Failure to comply can cause severe injury or death to the operator or bystanders.
Do not attempt to fasten the trigger in the “ON” position. This could lead to
an accidental discharge of the brad nailer. Do not operate the brad nailer if any
portion of the tool’s operating controls are inoperable, disconnected, altered in
any way or not in proper working order. Failure to comply with this warning
could result in serious injury or even death to the operator or other bystanders.
All air compressors must comply with the requirements of ANSI
b19.3. Pressure regulators must be used to limit air pressure where
air supply pressure exceeds the tool’s rated operating pressure.
Do not carry the brad nailer with a finger on the trigger. This could lead to an
accidental discharge of the brad nailer. Do not press the trigger of the brad nailer unless it is pressed firmly against the work piece. Do not point the brad nailer at yourself or in the direction of another person. Failure to comply with this
warning could result in serious injury or even death to the operator or other
bystanders.
Do not tamper with the work piece contact. The work piece contact prevents
accidental discharge of the brad nailer and should never be removed or compromised in any way. Failure to comply with this warning could result in serious injury or even death to the operator or other bystanders.
Always disconnect air hose and remove any remaining nails:
1. When brad nailer is left unattended.
2. Before performing any maintenance or repair on the brad nailer.
3. Before attempting to clear a jam in the brad nailer.
4. Before moving the brad nailer to a new location.
Always check the overall condition of the brad nailer before using. Check for
and tighten any loose screws. Ensure all safety systems are in working condition before using the brad nailer. The brad nailer must not operate if only the
trigger is pulled or if only the work piece contact is pressed against the work
piece. The brad nailer must only be used if both the trigger and work piece contact work at the same time.

5

Always use hearing protection to protect your ears against
hearing loss due to exhaust noise. Always wear proper safety glasses to prevent injuries to the eyes from fragments of
the work piece, defective nails or other debris caused by using the brad nailer. All safety glasses must have side shields and should conform to the requirements of the American National Standards Institute (ANSI) z87.1. Failure to
comply with this warning could lead to serious or permanent damage to the
ears as well as serious damage or permanent blindness in the eyes.
Never carry the brad nailer by the air hose. A sudden disconnection of the air
hose could cause the brad nailer to remain charged and an accidental firing
could occur. Failure to comply with this warning could lead to serious injury to
the operator or bystanders.
Always disconnect the power source and ensure the tool is not charged
before loading fasteners. Failure to comply with this warning could cause
severe injury or death to the operator, bystanders and severe damage to the
brad nailer.
Never use a non-relieving air coupler with the brad nailer. Always use couplers that release any built-up charge in the brad nailer’s firing mechanism. A
non-relieving air coupler can allow the brad nailer to discharge a fastener while
the tool is disconnected from the power source. Failure to comply with this
warning can result in serious or permanent injury or even death to the operator
or to bystanders.
Do not drive nails on top of other nails. Do not operate the brad nailer at too
steep of an angle. Nails can ricochet. Failure to comply with this warning can
result in serious injury or even death to the operator or bystanders.
Do not modify the brad nailer in any way. Unauthorized alterations can jeopardize safety in the tool’s operation. Failure to follow this precaution can result
in serious injury or even death to the operator or bystanders.
On rooftops and other high locations, always move forward as you use the
brad nailer. You can easily loose your footing if moving backwards. When nailing against a perpendicular surface, nail from the top down. This causes less
fatigue and reduces the chances of accidents.
Ensure the work area is sufficiently illuminated to operate power tools. The
work area should be clear and free of litter.

6

COMPONENT INSTALLATION
Thoroughly clean and maintain the brad nailer after every use. Lubricate
moving parts to prevent rust and minimize friction-related wear. Wipe down the
entire tool and remove all dust from the moving parts. Properly store the brad
nailer in a suitable case to keep it ready for the next job.
All maintenance and repairs should be performed by an authorized repair
facility. Call 1-888-278-8092 to obtain a list of repair facilities in your area or
to make arrangements to return the tool for service.
FUNCTIONAL DESCRIPTION

Never use a non-relieving air coupler with the brad nailer. Always use couplers that release any built-up charge in the brad nailer’s firing mechanism. A non-relieving air coupler can allow the brad nailer to discharge a fastener while the tool is disconnected from the power source. Failure
to comply with this warning can result in serious or permanent injury or even
death to the operator or to bystanders.
When selecting an air compressor, it must comply with the requirements of the
American National Safety Institute - ANSI B19.3.
Choose an air compressor that can supply more than the required air pressure to
ensure optimum efficiency. Always use clean, dry compressed air with a maximum
pressure of 200 psi. Use a pressure regulator and set the pressure between 60 –
115 psi. (4.0 – 8.0 kg/cm2G). Before each use, check the pressure regulator to
ensure it is functioning within the proper pressure range.
Using an air pressure of more than 120 psi can
cause the brad nailer to malfunction or possibly explode causing
severe injury or property damage.
SELECTING A PROPER AIR HOSE
Use an air hose with the largest diameter and shortest length possible to ensure
continuous, efficient nailing operations. Using an air pressure of 70 psi (5.0
kg/cm2G), an air hose with an inside diameter of 1/4" (6.5 mm) or greater and a hose
length of less than 6.6 ft (20 m), it is recommended that a 0.5 second interval be
allowed between each nailing. Air supply hoses shall have a minimum working pressure of 150 psi (10.7 kg/cm2G) or 150% of the maximum pressure produced by the
compressor or whichever is higher.

CONTROLS AND COMPONENTS:
1. Exhaust Cover
2. Trigger
3. Jam Clearing Door
4. No-mar Nosepiece
5. Empty Magazine Indicator
6. Nail Depth Adjuster
7. Hanging Hook
8. Air Inlet
9. Nail Magazine Lever
10. Nail Magazine Cover

11. Work Piece Contact
12. Trigger Actuation Mode Selector
ACCESSORIES:
13. Lubricant
14. Safety Glasses
15. Hex Wrenches (2)
16. F32 - Brad Strips

Low air output by the compressor or a longer hose with
a smaller inside diameter in relation to the nailing frequency may decrease
the driving capability of the air nailer.
SELECTING A QUICK DISCONNECT
1. Remove the plastic protective plug
from the tool’s air inlet.
2. Insert a 1/4" NPT male quick
disconnect into the air inlet. Install
the female portion to the air hose.

7

8

To improve the connection between the quick disconnect and air nailer, and to help
prevent oxidation, apply PTFE tape or joint compound to the connector threads
before insertion.

OPERATION IN SINGLE SEQUENTIAL ACTUATION MODE
To select the Single Sequential Actuation Mode (see
Figure 1):

3. Snap the air hose onto the quick disconnect on the air nailer. Check for air
leaks.

1. Press and hold the red Actuation Selector embedded
in the trigger.

LUBRICATION
To ensure maximum performance, it is recommended to install an air set (oiler, regulator, and air filter) as close as possible to the air nailer. Adjust the oiler so that
approximately one drop of oil will be released for every 50 nails.
If an air set is not used or is unavailable, oil the tool using pneumatic tool oil by placing 2 or 3 drops into the air inlet. This should be done before and after use. For
proper lubrication, the tool must be fired several times after the oil is introduced to
the filter.
OPERATING THE BRAD NAILER

Always use hearing protection to protect your ears against
hearing loss due to exhaust noise. Always wear proper safety glasses to prevent injuries to the eyes from fragments of
the work piece, defective nails or other debris caused by using the brad nailer. All safety glasses must have side shields and should conform to the requirements of the American National Standards Institute (ANSI) z87.1. Failure to
comply with this warning could lead to serious or permanent damage to the
ears as well as serious damage or permanent blindness in the eyes.
Always disconnect the air hose before making adjustments or checking the
functionality of the air nailer.
SELECT TRIGGER ACTUATION MODE
The brad nailer is equipped with a selectable trigger. This allows the selection of
Single Sequential Actuation Mode or Contact Actuation Mode.

9

2. Rotate Actuation Selector down to the Single
Sequential Actuation (T).
3. Release Actuation Selector, ensuring locking tab is
fully seated in the slot.

Figure 1

Ensure selector has locked into position. Ensure
actuation process is fully understood before attempting to use brad nailer.
TO USE THE BRAD NAILER IN SINGLE SEQUENTIAL
ACTUATION MODE:
1. Firmly grip brad nailer handle.
2. Position brad nailer work piece
contact on work piece surface.
3. Push brad nailer against work piece
compressing work piece contact.
4. Pull trigger on brad nailer to drive
nail. The brad nailer will recoil away
from the work piece as nail is driven.
5. Remove finger from trigger and lift
brad nailer away from surface of work
piece.

OPERATION IN CONTACT ACTUATION MODE

When using contact actuation mode, be careful of unintentional double fires resulting from tool recoil. Unwanted fasteners may be
driven if the work piece contact is allowed to accidentally re-contact the work
piece.

10

To select Contact Sequential Actuation Mode (see Figure 2):
Always disconnect the brad nailer before making any
adjustments to the nail depth knob.

1. Press and hold Actuation Selector embedded in the
trigger.
2. Rotate Actuation Selector up to the Contact
Sequential Actuation (TTT).
3. Release Actuation Selector, ensuring locking tab is
fully seated in the slot.

USING THE HOOK

Figure 2

Ensure selector has locked into position. Ensure
actuation process is fully understood before attempting to use brad nailer.

Always disconnect the air hose before hanging the brad nailer with the hook.
NEVER hook the brad nailer in a high location or on an unstable platform.
LOADING NAILS INTO THE AIR NAILER

TO USE THE BRAD NAILER IN CONTACT ACTUATION MODE:
1. Firmly grip brad nailer handle.
2. Pull and hold the brad nailer trigger.
3. Push brad nailer against work piece compressing work piece contact.

Always disconnect the air hose from the brad nailer before adding or removing nails to the brad nailer.

4. The brad nailer will drive nail upon contact. The brad nailer will recoil away
from the work piece as nail is driven.

NEVER use deformed nails or nail strip. Failure to observe this precaution
can result in poor nail feeding and/or jams in the feeding mechanism.

ADJUSTING DEPTH OF NAILING

To load nails in brad nailer, depress magazine lever and pull magazine cover to back
of magazine. (Figure 4). Insert nails and slide magazine cover over nails until it locks
into place.

Be aware of material thickness when using nailer. A protruding nail may cause injury.
Adjust the depth of nailing by turning the
adjustment knob (Figure 3, Item 1) to the left (A)
for the shallowest setting and to the right (B) for
the deepest setting. To increase the depth of the
nails, when the adjustment knob is already set to
its lowest setting, increase the air pressure. To
decrease the depth of nails when the adjustment
knob is already set to its highest setting,
decrease the air pressure. Should nails be driven
too deep even when the adjustment knob is set
at its lowest setting, decrease the air pressure. In
general, the brad nailer will have a longer service
life when the adjustment knob is set at a lower
setting causing less wear and tear on the driving
mechanism.

11

Figure 4

USING THE NO-MAR NOSEPIECE
Always disconnect the air hose before attaching the
Figure 3

no-mar nosepiece.

12

6. Select Single Sequential Actuation Operation. Check for leaks. Without pulling
the trigger, press the work piece contact against the work piece. The tool
MUST NOT operate. Holding the tool away from the work piece, pull trigger
and hold for 5 seconds. The tool MUST NOT operate. Repeat steps several
times. Without pulling trigger, press nailer against work piece and pull trigger.
The tool MUST operate. Release trigger. Driver MUST move up.

In order to prevent the surface of the work piece from being
scratched or damaged, use the no-mar nosepiece. Install
no-mar nosepiece by pressing it into place on the nose
frame. See Figure 5.
Store the no-mar nosepiece in place when not being used.

7. Select Contact Actuation Operation. Holding nailer away from work piece, pull
trigger. The tool MUST NOT operate. While still pulling trigger, press the nailer
against work piece. The tool MUST operate.

Figure 5

8. If Steps 1 through 7 function properly, prepare the tool for use. Select operation mode and load fasteners.
9. Set the required depth of drive.

Never use a non-relieving air coupler with the brad nailer. Always use couplers that release any built-up charge in the brad nailer’s
firing mechanism. A non-relieving air coupler can allow the brad nailer to
discharge a fastener while the tool is disconnected from the power source.
Failure to comply with this warning can result in serious or permanent injury
or even death to the operator or to bystanders.
When the air hose is disconnected, the pressure reservoir in the air nailer will discharge removing any built-up air inside the tool.
REQUIRED DAILY PREPARATION
The following steps should be performed on a daily basis to ensure the brad nailer
is operating correctly:
1. Disconnect air supply from nailer and remove fastener strip.
2. Check all screws, nuts and pins and ensure all are tight.
3. Press the pusher release button and slide back the pusher assembly
(Overriding the reload indicator). Press the work piece contact against a work
piece ensuring smooth movement.

10.Repeat these steps daily. Test again if the nailer is dropped, jammed, etc.
USING THE AIR NAILER
To drive a nail, place the work piece contact of the brad nailer against the work
piece and pull the trigger. See Figure 6.
To avoid any unexpected nailings,
perform the operation as follows:
1. Avoid placing the work piece contact
against the work piece with excessive
force.
2. Pull the trigger fully and hold it in the
fired position for 1 to 2 seconds
before releasing the trigger. This will
give the brad nailer time to completely expend the previous nail and build
enough pressure for the next nail.

Figure 6

4. With work piece contact against the work piece, pull trigger. The trigger must
operate smoothly.
5. Connect air supply and set regulator for 70 psi. DO NOT load a fastener strip.

DO NOT hold the trigger in a half-pulled position. This
could cause an unexpected nailing to occur if the work piece contact is permitted to re-contact the work piece. Failure to comply could result in damage to
work piece.

13

14

CHANGING DIRECTION OF EXHAUST AIR

OVERALL MAINTENANCE OF AIR NAILER

The direction of exhaust air on the air nailer can be
directed 360˚ degrees by placing hand on exhaust
cover and turning. See Figure 7.

Always disconnect the air hose from brad nailer before
attempting any type of maintenance or visual inspection of tool.
Always visually inspect brad nailer before every use. Check on the overall condition
and for any loose screws. Tighten any screws that have come loose. See Figure 9.
Visually inspect the work piece contact and
trigger to ensure there is free movement. See
Figure 10.

Figure 7

CLEARING JAMS
Typically, jams are caused when a fastener or a fastener fragment becomes wedged
between the driver blade and nail guide. Using the wrong fastener can also cause jams.
TO CLEAR A JAM:
1. Disconnect the air supply and remove the
fastener strip. Leave the pusher assembly
open.

Figure 8

When the tool is not going to be used for an
extended period, wipe off all dust and debris
that have collected on it. Tighten all loose
screws. Lubricate the firing mechanism with
pneumatic tool oil. See page 9 for
Lubrication.
Figure 9

2. Pull out the latch tab and open the jamclearing door.

Store the brad nailer in a safe location or in
suitable carrying case. It is recommended
that the air nailer be secured in a locked
location to prevent unauthorized usage.

3. Remove all debris that has built up
during operation.
4. Remove jammed fastener. If fastener is difficult to grasp, use needle nose pliers instead
of fingers.
5. If necessary, insert a flat-blade screwdriver
so that it touches the tip of the driver blade.
See Figure 8. Tap the screwdriver with a
hammer. The screwdriver will push the driver
blade back, freeing the jam.
6. Close the jam-clearing door securely.
MAINTENANCE

Avoid exposure to direct sunlight and/or
locations with high humidity and heat.

Figure 10

Remove the brad nailer from use and schedule to have
it repaired at an authorized repair facility if the work piece contact is binding or not moving freely. Do not attempt to repair the brad nailer. Failure to
comply can result in malfunction of the tool and severe injury to the operator or any bystanders.

STORAGE OF NAILS
Always handle nail strips and their box very carefully. If the nail strips have been mishandled, they may be out of shape or have breaks in the connecting strips. This will
cause the nails to feed poorly and possibly result in misfiring or jams in the air nailer.
Avoid storing nails in a very humid or hot environment or place in direct sunlight.

15

16

MANDATORY MAINTENANCE
All maintenance and repairs should be performed by an
authorized repair facility. Call 1-888-278-8092 to obtain a list of repair facilities in your area or to make arrangements to return the tool for service.
ACTION

REASON

Clean magazine and
feeder mechanism.

Prevents brad nailer
from jamming.

Inspect and ensure work
piece contact operates
properly.

Ensures operator safety
and keeps brad nailer
working efficiently.

Lubricate brad nailer
after every use using
pneumatic tool oil.

Extends life of brad nailer.

PROBLEM

POSSIBLE CAUSE

SOLUTION

Weak drive. Slow to
cycle between nailings.

Ensure proper air pressure is being used.
Inspect for worn driver
blade.
Inspect piston O-ring for
wear or damage.

Increase air pressure,
Do not exceed 120 psig
(8.3 bars, 8.5 kg/cm2)
Contact Customer
Service.

Nails driven too deep.

Check air pressure.

Reduce air pressure.

Brad nailer feeds intermittently or skips nails.

Ensure correct nails are
being used.
Inspect nail feeder
mechanism.
Piston O-ring damaged
or worn
Nail feeder worn or
damaged.

Use ONLY recommended nails.
Clean and lubricate nail
feeder.
Use recommended
pneumatic tool oil.
Contact Customer
Service.
Replace nail feeder.

Nails jam or driven nail
is bent.

Ensure correct nails are
being used.
Inspect for worn driver
blade.
Nail feeder worn or
damaged.

Use ONLY recommended nails.
Contact Customer
Service.
Replace nail feeder.

Drives nails properly
during normal nailing
operations, but fails to
drive nails fully at faster
operating speeds.

Check inside diameter of
air hose.

Switch to air hose with
larger inside diameter.

OPERATION
Use compressed air and
clean daily.

Use compressed air and
clean daily.
Apply 2 – 3 drops of
pneumatic tool oil to
brad nailer air inlet after
every use.

TROUBLESHOOTING
Most minor problems can be resolved quickly and easily using the troubleshooting
table below. For problems that cannot be solved, contact Customer Service (toll
free) at 1-888-278-8092.
PROBLEM

POSSIBLE CAUSE

SOLUTION

Nailer operates, but no
nail is driven.

Check for jammed nail.
Inspect nail feeder
mechanism.
Ensure correct nails are
being used.

Clear jammed nail.
Clean and lubricate nail
feeder.
Use ONLY recommended nails.

17

18

PARTS DIAGRAM

PARTS LIST
ITEM NO.

19

PART NO.

DESCRIPTION

1

A0000-1211

Nylon Screw M4*8

2

A0005-0691

Washer 12*1

3

A0304-0651

Exhaust Cover

4

A0200-2471

O-Ring 7.59*2.62

5

B0000-0051

Screw Set M5*20

6

A0000-0091

Screw M5*20

7

A0005-0031

Washer #5*1.21

8

A0301-1541

Cap, Top

9

A0311-0451

Seal, Air

10

A0200-0221

O-Ring 15*2.5

11

A0205-0651

Gasket

12

A0100-0631

Spring

13

K0300-2221

Firing Valve Piston Set

14

A0200-0711

O-Ring 33.5*2.5

15

A0308-0341

Firing Valve Piston

16

A0200-0601

O-Ring 26.59*2.95

17

A0313-0041

Piston Stopper

18

K0600-2111

Piston Unit

19

A0200-1281

O-Ring 22.4*3.3

20

B0600-2101

Piston Set

21

A0305-0081

Sleeve Retainer

22

A0200-0271

O-Ring 44.8*2.6

23

A0800-0391

Spacer

24

A0200-0071

O-Ring 31*2.5

20

ITEM NO.

PART NO.

25

A0303-0901

26

DESCRIPTION

ITEM NO.

PART NO.

Cylinder

50

K0700-5771

Release Catch

A0309-0741

Bumper

51

A0711-2601

Release Catch (C)

27

K0400-0601

Body and Handle Grip

52

A0009-0071

Steel Ball

28

A0204-1661

Grip

53

A0100-2741

Spring

29

A0401-1951

Body

54

A0714-0651

Adjustment Wheel

30

A0310-0751

Nozzle

55

A0711-2821

Release Catch (B)

31

A0006-0821

Trigger Pin

56

A0005-1021

Stopping Ring

32

A0005-0311

Pin Retainer 5.5*2

57

A0000-0071

Screw M5*16

33

A0011-0161

Spring Pin 3*24

58

A0800-0901

Spacer

34

A0313-0631

Main Body Bumper L(Snap-on)

59

A0001-0001

Screw M4*18

35

A0313-0641

Main Body Bumper R(Snap-on)

60

A0801-2791

Driver Guide

36

A0006-0411

Pin

61

A0701-2551

Lower Magazine

37

A0005-0291

Pin Retainer 6*2.9

62

A0708-0321

Steel Bar

38

A0316-0331

Belt Hook

63

A0706-0781

Support

39

A0200-2851

O-Ring 38*3.5W

64

A0715-0191

Magazine Stop

40

A0203-0191

Filter

65

A0000-0241

Screw M5*14

41

A0306-1181

Tail Cover

66

A0000-0521

Nylon Screw M4*12

42

A0101-0191

Spring

67

A0700-1361

Upper Magazine

43

A0709-0301

Click Lever

68

A0011-0131

Spring Pin 3*10

44

A0712-0341

Safety Guide Plate

69

A0718-0701

Tail Cover

45

A0100-0811

Spring

70

A0707-2001

Pusher

46

A0200-1091

O-Ring 11*1.05

71

A0706-1731

Spring Holder

47

K0500-1381

Trigger Valve Set

72

A0200-0291

O-Ring 4*1.25(Red)

48

K0500-1491

Trigger Set

73

A0101-0431

Spring

49

K0800-0411

Driver Guide Cover Set

74

A0204-1571

No Mar Pad

21

DESCRIPTION

22

SPECIFICATIONS
MODEL NUMBER

870016

AIR PRESSURE

60-115 PSIG (4.0- 8.0 kg/cm 2 G)

NAIL LENGTH

5/8" (15 mm) - 1 1/4" (31.75 mm)

NAIL CAPACITY

110 NAILS

MINIMUM HOSE
DIAMETER

1/4" (6.5 mm)

NAIL DIAMETER

18 GAUGE

NET WEIGHT

2.6 LBS. (1.17KG)
1 YEAR LIMITED WARRANTY

Express and Exclusive Limited Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail
purchaser of the accompanying SNAP-ON™ portable air tool and no one else all
parts of the product (except those parts referred to below which are specifically
excluded from such warranty (see Exclusions) to be free from defects in materials
and workmanship for a period of one year from the original date of purchase.
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody, or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified or altered. This warranty does not apply to any other
product and/or component thereof manufactured or distributed by Alltrade, and
does not apply to products and/or components thereof designed, manufactured
and/or assembled by others, for which Alltrade makes no warranties whatsoever.
THERE ARE NO WARRANTIES, WHICH EXTEND BEYOND THE DESCRIPTION ON
THE FACE HEREOF.
WARRANTY PERFORMANCE
By purchasing this product, purchaser expressly acknowledges and agrees that
their sole and exclusive remedy under this warranty shall be strictly limited to the
repair or replacement of any covered nonconforming items or parts thereof provided that any such nonconforming item and/or part is promptly returned to an authorized Service Center within the applicable warranty period, with a written request by
purchaser to repair and/or replace the nonconforming item and/or part. We recommend that you keep the original product packaging in the event you need to ship the
unit. We suggest the package be insured against loss or in transit damage. When

23

sending your product, include your name, address, phone number, e-mail address,
dated proof of purchase (or copy) and a statement about the nature of the problem.
Warranty coverage is conditioned upon purchaser furnishing Alltrade with adequate
written proof that they are the original purchaser and of the original purchase date.
Parts returned, freight prepaid and insured, will be inspected and, at Alltrade's
option, repaired and/or replaced free of charge if it is found to be defective and subject to warranty. Alltrade retains the sole discretion to determine whether any item
or part is nonconforming and, if so, whether the item and/or part will be repaired
and/or replaced. If the unit is repaired, new or reconditioned replacement parts may
be used. If Alltrade chooses to replace the product, it may replace it with a new or
reconditioned of the same or comparable design. The repaired or replaced unit will
be warranted under the terms of the remainder of the one year warranty period; covered defective parts not subject to normal wear and tear or other exclusions will be
repaired or replaced, at Alltrade's option. During the warranty period, Alltrade will
be responsible for the return shipping charges. Alltrade's repair and/or replacement
of any nonconforming item and/or part thereof shall constitute fulfillment of all obligations to the purchaser. Alltrade shall not be responsible or liable for any expense,
including freight charges, or repairs made outside Alltrade's facility or an Alltrade
designated service, unless expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade bear any responsibility for loss of the unit, loss of time or
rental, inconvenience, commercial loss, or consequential damages.
For the location of an Authorized Service Center nearest you, please call customer
service at 1-888-278-8092.
EXCLUSIONS
Air nailers and staplers need periodic maintenance to remain in proper operating
condition. Normal wear parts (o-rings and driver blades) shall be warranted to the
original purchaser to be free from defects in materials and workmanship for a period of 90 days from the original date of purchase.
This warranty does not cover parts damaged due to normal wear, abnormal conditions, misapplication, misuse, abuse, accidents, operation, improper storage, or
freight damage. Parts damaged or worn by operation in dusty environments are not
warranted. Failure to follow recommended operating and maintenance procedures
also voids warranty.
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY, USE
OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES, OR OTHER
CAUSES UNRELATED TO PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE
NOT COVERED BY THIS WARRANTY.

24

Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons; pre-delivery services such as assembly, oil and lubricants, and adjustment; maintenance
services that are normally required to maintain the product.
The use of other than genuine Snap-On™ Repair Parts will VOID the warranty.
WARRANTY DISCLAIMERS
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS, EXCEPT FOR THE LIMITED WARRANTY
PROVIDED HEREIN, ALL OTHER EXPRESS WARRANTIES, GUARANTIES, AND/OR
REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSE OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER'S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.

SENTATIVE(S) AND PURCHASER, AND WARRANTY HEREUNDER, AND/OR THE
EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF
ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES. IN NO
EVENT, WHETHER BECAUSE OF A BREACH OF CONTRACT, WARRANTY, TORT
(INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL ALLTRADE'S AND/OR ITS
REPRESENTATIVE (S) LIABILITY EXCEED THE PRICE OF THE PRODUCT. All LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE UPON
THE EXPIRATION OF THE WARRANTY PERIODS SPECIFIED ABOVE.
LIMITATIONS ON WARRANTY DISCLAIMERS
Some states do not allow limitations on how long an implied warranty lasts and
some states do not allow the exclusion or limitation of the incidental or consequential damages, so part or all of the above limitations or exclusions may not apply to
you. This warranty gives you specific legal rights, and you may also have other
rights, which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department at 1-888-278-8092 for general repair information, and charges and the
location of your nearest authorized service facility.

EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE WARRANTY
LISTED HEREIN IS MADE WITH REGARD TO THIS PRODUCT. ALL WARRANTIES
AND/OR IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY
ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH
WARRANTY, GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES
BY OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND
WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS
AND/OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON.
PURCHASER'S SOLE AND EXCLUSIVE REMEDY IS AS STATED ON PRECEDING
PAGES.
LIMITATIONS OF LIABILITY
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OR PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS REPRE-

25

26



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Page Count                      : 14
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:e9f4223c-8b44-11dd-8278-003065839dea
Producer                        : Acrobat Distiller 6.0.1 for Macintosh
Create Date                     : 2008:09:25 13:59:33-07:00
Modify Date                     : 2008:09:25 13:59:33-07:00
Document ID                     : uuid:e9f3f44c-8b44-11dd-8278-003065839dea
Format                          : application/pdf
Title                           : untitled
EXIF Metadata provided by EXIF.tools

Navigation menu