Socket Mobile CRS001 Hands Free Scanner with Bluetooth User Manual Socket Cordless Ring Scanner User s Guide
Socket Mobile, Inc. Hands Free Scanner with Bluetooth Socket Cordless Ring Scanner User s Guide
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 659411 |
| Application ID | Ro1xuB3QC/fQsh6XT2fsNA== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 41.88kB (523442 bits) |
| Date Submitted | 2006-05-17 00:00:00 |
| Date Available | 2006-05-17 00:00:00 |
| Creation Date | 2006-04-20 16:39:37 |
| Producing Software | Acrobat Distiller 7.0.5 (Windows) |
| Document Lastmod | 2006-04-20 16:43:25 |
| Document Title | Socket Cordless Ring Scanner User's Guide |
| Document Creator | Acrobat PDFMaker 7.0.7 for Word |
| Document Author: | Michelle Man |
Cordless Ring Scanner Series 9 with Bluetooth® Wireless Technology Featuring a “Hands-Free” Bluetooth enabled bar code scanner to capture and send data wirelessly to Bluetooth enabled Pocket PCs and other Windows Mobile-based devices User’s Guide 4/2006 Document # 6410-00273 C Copyright Notice Copyright © 2006 Socket Communications, Inc. All rights reserved. Socket, the Socket logo and Battery Friendly are registered trademarks of Socket Communications, Inc. Cordless Ring Scanner with Bluetooth Wireless Technology, SocketScan and Mobility Friendly are trademarks of Socket Communications, Inc. Bluetooth and the Bluetooth logos are trademarks owned by Bluetooth SIG, Inc., U.S.A. and licensed to Socket Communications, Inc. All other brand and product names are trademarks of their respective holders. The Socket Cordless Ring Scanner includes technology licensed under United States Patent No. 5,902,991. Reproduction of the contents of this manual without the permission of Socket Communications is expressly prohibited. Please be aware that the products described in this manual may change without notice. Feel free to contact SOCKET COMMUNICATIONS at: Socket Communications, Inc. 37400 Central Court Newark, CA 94560 Other than the above, Socket Communications can assume no responsibility for anything resulting from the application of information contained in this manual. Please refrain from any applications of the Socket Cordless Ring Scanner that are not described in this manual. Please refrain from disassembling the Cordless Ring Scanner. Disassembly of this device will void the product warranty. You can track new product releases, software updates and technical bulletins by visiting Socket’s web page at: www.socketcom.com. Table of Contents COPYRIGHT NOTICE 1 | INTRODUCTION About the Software About Combining Scanning with Bluetooth System Requirements Package Contents Product Registration Hardware and Software Indicators Scanning Tips 2 | SETUP FOR WINDOWS MOBILE STEP 1: Charge and Install the Battery STEP 2: Install the Software STEP 3: Configure Scanner Settings STEP 4: Connect CRS to Host Device with Bluetooth STEP 5: Put on the CRS STEP 6: Scan Data into Your Application OPTIONAL: Select Symbologies OPTIONAL: Configure Prefix/Suffixes OPTIONAL: Run Scan Demo 10 11 11 14 15 17 18 19 20 21 APPENDICES A | SPECIFICATIONS 22 B | SAFETY AND USAGE TIPS 24 C | BAR CODE LABEL SPECIFICATIONS 26 D | ENABLING OR DISABLING SYMBOLOGIES 27 E | DECODE ZONE 30 F | TROUBLESHOOTING 31 G | TECHNICAL SUPPORT 33 LIMITED WARRANTY 34 REGULATORY COMPLIANCE 36 1 | Introduction If you need to collect bar coded data but don't want to be tied to your mobile or desktop computer, the Socket Cordless Ring Scanner (CRS) Series 9 with Bluetooth wireless technology is just what you're looking for. This innovative device combines the power of laser bar code scanning with the convenience of Bluetooth wireless technology in a single compact, lightweight device that is ergonomically designed to fit comfortably on your hand. Bar code scanning is the most efficient way to collect data for a mobile computer. If the data to be entered is bar coded, using a laser scanner is 50 times faster and 10,000 times more accurate than manual data entry. Bluetooth wireless technology transforms how devices connect with each other, offering you new possibilities for using your mobile computer with other devices. With the Socket CRS, you can scan bar codes while connected to the PDA in your pocket or located up to 300 feet away — all without the hassle of cables or the awkwardness of a protruding antenna. The Battery Friendly® CRS was designed to use minimal power, so you can use the CRS to scan 10,000 times in 8 hours in normal operating conditions without having to stop and recharge. About the Software SocketScan™ enters scanned data directly into any open Windows program, as if the data were manually typed. You can configure Prefix/Suffixes and assign a beep tone to signify good data reads at the host. The Socket Cordless Scanner utility makes it easy to configure SocketScan for use with the Cordless Ring Scanner. Simply identify which kind of Bluetooth hardware you will be using on your mobile computer, and SocketScan will automatically search for it when you try to connect. Connect!Agent for Windows Mobile (patent pending) simplifies the Bluetooth setup and connection process. Once the CRS is turned on and SocketScan is running, Connect!Agent will automatically discover and set up the Bluetooth connection and continue to manage the connection. Connect!Agent runs in the background and requires no interaction from the user. For software updates, please visit: www.socketcom.com/support/support_bar.asp About Combining Scanning with Bluetooth The Cordless Ring Scanner represents an optimal combination of proven laser bar code scanning technology and state-of-the-art Bluetooth connectivity. Because of the problems inherent in the intermittent storage of scanned data in on-board memory if the Bluetooth connection is lost, the CRS is designed to operate only when connected to the host, with the powerful Class 1 radio providing the maximum possible connection range. The user is advised of the connection status with a single beep when the CRS connects to the host and a double beep when the connection is closed or lost. As with any wireless device, connectivity range can be affected by a variety of environmental variables. The most likely source of errors in any cordless scanning system is not in the scanning and decoding process, but in the transmission of the data to the host. To prevent such errors, the Cordless Ring Scanner features Socket’s exclusive Error Proof Protocol (patent pending), which ensures that scanned data is correctly received by the host computer and allows for realtime validation of data and notification to the user in case of errors. The beeper and green LED signals provided by the CRS confirm not only a successful scan but also the successful transmission of the scanned data to the host. Users familiar with bar code scanning may notice a slight delay between the successful scan and shut off of the laser and the beep and green LED from the CRS confirming completed transmission of the data. In most instances, this delay is less than 300 ms (milliseconds), but may be slightly longer as the connectivity range limit is approached. Because of the two-way transmission verification process, it is possible to cause communication problems by scanning bar codes as fast as possible. When this occurs, all transmissions will stop for several seconds before CHAPTER 1: INTRODUCTION scanning can be resumed. To prevent this from happening, the user should wait until the confirming beep is received before scanning the next bar code. System Requirements Your mobile computer should meet these minimum requirements: • Windows Mobile 2003/2003SE/5.0 • Any of the following Bluetooth stacks: − Socket Drakar v1.4 (from Socket SD/CF Connection Kits) − Broadcom (Widcomm) v1.4 − Microsoft Bluetooth stack for Pocket PCs • Software installation requires ActiveSync 4.0 or greater Package Contents The Socket Cordless Ring Scanner package includes these items: • Ring scanner (C) • Wrist unit (A) • Cable (B) • Wrist unit case (D) • Finger strap (F) • 2 adhesive Velcro strips (G) • Rechargeable 3.7V lithium-ion battery • Battery charger • CD with software and user documentation Product Registration Socket highly recommends that all customers register their Socket products. Registered users receive the following benefits: • Priority for technical support • Special offers for future products and upgrades • The latest new product information. Register online at: www.socketcom.com/prodreg Hardware and Software Indicators Battery Charger LEDs LED Power Charging LED Activity Red Meaning Plugged into valid power source Yellow Charging Green Battery is fully charged Scanner LED LED Good Read LED Activity Green Meaning Data successfully scanned and sent to host device LED Activity Blinking blue every second Blinking blue, every 5 seconds Blinking Red Meaning Wrist Unit LEDs LED Bluetooth Status Battery Status Bluetooth radio is on, no connection Bluetooth connection 20% battery capacity remaining Solid Red 10% battery capacity remaining Off Off or Good Battery status Wrist Unit Beeps Beep Pattern 1 beep Meaning Bluetooth connection to host device has begun or power on 2 beeps Bluetooth connection to host device has ended or power off 1 beep (optional setting) Data successfully scanned and sent to host device 3 beeps Cable disconnected from wrist unit SocketScan Icon Bottom of Today screen when SocketScan is open. Tap for menu. Icon Meaning The CRS is not connected to the host device The CRS is connected to the host device CHAPTER 1: INTRODUCTION Scanning Tips Practice to determine the best scanning angle and distance for your type of bar code. Scan Angle For best results, position the scanner at an angle to the bar code, at least 15° from perpendicular. Otherwise, light can bounce back into the scanner and “blind” the sensing mechanism. Aiming Beam Aim the laser so that the red beam covers the entire width of the bar code. Scanning Distance • • • The optimal scanning distance varies depending on the bar code size, symbology, label media, W-N Ratio, and scan angle. In general, the CRS can successfully scan 2.2 to 30+ inches from the bar code. The larger the bar code, the further away you should position the scanner. The tighter the bars of the bar code, the closer you should position the scanner. CHAPTER 1: INTRODUCTION 2 | Setup for Windows Mobile This chapter explains how to install and use the Cordless Ring Scanner (CRS) with a Bluetooth enabled Pocket PC or other Windows Mobilebased device. Setup Summary STEP 1: Charge and install the battery. STEP 2: Install the software. STEP 3: Configure scanner settings. STEP 4: Connect scanner to host device with Bluetooth. STEP 5: Put on the CRS. STEP 6: Scan data into your application. OPTIONAL: • Select symbologies. • Configure prefix/suffixes. • Run Scan Demo application. 10 STEP 1: Charge and Install the Battery 1. The battery must be charged before initial use, using the included Socket approved charger. The Charging LED will be yellow during charging. After the battery reaches full charge, which takes about 4 hours, the Charging LED will turn green. Do not use the charger with other types of batteries. A fully charged battery should provide at least 10,000 scans and more than 8 hours of operation. 2. Slide the switch at the bottom of the wrist unit to the right to unlock the battery door. Insert the battery so that the battery contacts align with the contacts inside the wrist unit, then close and lock the battery door. WARNING: Do not insert the battery backwards or upside-down. Damage may result. STEP 2: Install the Software Should I install Connect!Agent? Connect!Agent simplifies the Bluetooth setup and connection process. Once the CRS is turned on and SocketScan is running, Connect!Agent will automatically discover and set up the Bluetooth connection and continue to manage the connection. Connect!Agent runs in the background and requires no interaction from the user. Connect!Agent is optional to install. CHAPTER 2: SETUP FOR WINDOWS MOBILE 11 Installation Instructions for Connect!Agent or SocketScan Connect the CRS to your mobile computing device and make a test scan to verify that your CRS works before you install Connect!Agent. ADVANCED USERS: Refer to the README file for CAB file installation instructions. 1. Delete any bar code scanning software already installed in your device, including software from other companies. Make sure the software is closed. Tap Start | Settings | System tab | Remove Programs. Use the utility to delete the software. 2. Use ActiveSync and a serial/Ethernet/USB cable or cradle to make an active connection between the mobile computer and a host PC. IMPORTANT: ActiveSync 4.0 or greater is required. 3. Insert the installation CD into your host PC. 4. Use My Computer or Windows Explorer to access your CD-ROM drive. In the CD contents, open the SocketScan folder and click on the Setup.exe file. 5. The installation wizard will automatically begin. Follow the wizard to install the software. 12 6. After installing the software, a dialog on your Pocket PC will direct you to soft reset. Tap Yes or ok to proceed. 7. If desired, install Connect!Agent by repeating the same process, but launching the Setup.exe file inside the Connect!Agent folder in the CD. CHAPTER 2: SETUP FOR WINDOWS MOBILE 13 STEP 3: Configure Scanner Settings 1. Tap Start | Settings | System tab | Socket Scanner Settings. Alternatively, tap Start | Programs | SocketScan. Go to the Today screen. Tap the SocketScan icon at the bottom of the screen. In the pop-up menu, tap Settings. 2. Tap on the CS tab at the bottom of the screen. Check Enable Cordless Scanner support. Under Bluetooth Port Configuration, if your device has a built-in Bluetooth radio, your Bluetooth stack will be reported (e.g., Widcomm). If you installed Connect!Agent and would like to use it, select Connect!Agent from the list. If your device does not have a built-in Bluetooth radio, select Socket to use your device with the Socket SD/CF Bluetooth card. 3. Tap on the CS HW tab. Enter the following settings: • Trigger: Select whether you would like the CRS to scan only when a Bluetooth connection to the device is detected. If you require the CRS to detect a Bluetooth connection before each scan, scanning will be a few milliseconds slower. • Good Read Indicator: Select how you would like the CRS to indicate that it has successfully read data. • Battery Level: No progress bar should appear since you are not connected to the CRS. • Disable Auto Power Off mode: The CRS automatically shuts off if there is no Bluetooth connection for 20 minutes. Check to disable. 4. Tap on the CRS tab. Select which button on the CRS you would like to use to trigger the scanner. 5. After entering settings, tap ok to save the changes. 14 STEP 4: Connect CRS to Host Device with Bluetooth 1. Turn on the Cordless Ring Scanner. Press the small power button on the side of the wrist unit for at least 2 seconds, until you hear a beep. The Bluetooth status LED on the wrist unit should be blinking blue. 2. Turn on the Bluetooth radio of your mobile device. Refer to your device manual for instructions. 3. If you did not install Connect!Agent, make sure a COM port is enabled for outbound Bluetooth serial communication. Refer to the device manual. 4. Tap Start | Programs | SocketScan. Disregard the icons for Socket Trigger RFID, Socket Trigger Scan, and Socket Trigger Select. at the bottom of the 5. Tap on the SocketScan icon screen. In the pop-up menu, tap Connect CS. Your mobile device cannot connect to the CRS if another device is set as the default Bluetooth serial device. If Connect CS does not appear, tap Settings in the menu, tap on the CS tab, and enable cordless scanner support. 6. Your device will begin searching for the CRS. • If you installed Connect!Agent, your mobile device will automatically search for and connect to the CRS. A beep will indicate the connection. • If you did not install Connect!Agent, your device’s Bluetooth software will search for devices. In the list of found Bluetooth devices, select Socket CRS. The device will connect to the CRS, indicated by a beep. The six characters following the device name are the last six characters of the Bluetooth MAC address. If using the Broadcom (Widcomm) stack, you will be prompted to configure automatic connections. If a passkey is requested, enter 1234. CHAPTER 2: SETUP FOR WINDOWS MOBILE 15 7. After your mobile device connects to the CRS, the SocketScan icon at the bottom of the Today screen will change into a ring icon to indicate the connection. Connect!Agent will save information about the CRS to automate future connections to your specific unit. If the Pocket PC suspends or the CRS is taken out of range, the Bluetooth connection will be lost. After the Pocket PC comes out of suspend mode or returns within range, SocketScan will try to re-establish the connection every 10 seconds for 30 seconds. 16 STEP 5: Put on the CRS You can put on the CRS either with or without the case. If you choose not to use the case, the wrist unit will be more susceptible to abuse, specifically the plastic parts. How to put on the CRS with the wrist unit case 1. Insert the wrist unit into the case. During insertion, you may hear a beep because the wrist unit’s power button was pressed, however, the wrist unit will not turn on unless the button was pressed for more than 2 seconds. 2. Use the cable to connect the CRS to the wrist unit. The white arrows of the cable connectors should be on top. 3. Attach the finger strap to the bottom of the ring scanner. 4. Put on the wrist strap. Adjust it for a secure and comfortable fit. 5. Attach the wrist unit case to the wrist strap, by pressing the Velcro together. 6. Put the ring scanner on your index finger, adjusting the finger strap for a secure and comfortable fit. How to put on the CRS without the wrist unit case Note: After you stick the Velcro strips to the wrist unit, the wrist unit will no longer fit in the case, unless the Velcro strips are removed. 1. Stick the 2 adhesive Velcro strips horizontally to the back of the wrist unit. Do not space the strips too far apart. Note the size of the Velcro on the wrist strap. 2. Use the cable to connect the CRS to the wrist unit. The white arrows of the cable connectors should be on top. 3. Attach the finger strap to the bottom of the ring scanner. 4. Put on the wrist strap. Adjust it for a secure and comfortable fit. 5. Attach the wrist unit to the wrist strap, by pressing the Velcro together. 6. Put the ring scanner on your index finger, adjusting the finger strap for a secure and comfortable fit. CHAPTER 2: SETUP FOR WINDOWS MOBILE 17 STEP 6: Scan Data into Your Application 1. Start the Windows application that you want to enter scanned data into (e.g., Excel, Notepad, etc.). Make sure a document or spreadsheet is open. 2. Place the cursor where you want data from the next scan to be entered. 3. Press the trigger button and aim your finger at the bar code. The red laser beam should cover the entire width of the bar code. See the next page for scanning tips. When data is read and sent to the mobile computing device, the laser will turn off. Depending on your scanner settings, the scanner may beep and/or the ring scanner’s LED may flash green to indicate a good read. If no data is read in a few seconds, the laser will turn off, and you must try again. 4. After a successful scan, data should appear in your document. By default, the cursor automatically advances to the next cell or line, ready for the next scan. Wait for the “Good Scan” indication before you scan another bar code. If you try to scan too fast, the device can lock up until you stop scanning. To turn off the CRS, press the power button on the wrist unit for at least 2 seconds, until you hear 2 beeps. 18 OPTIONAL: Select Symbologies The applet makes it quick and convenient to modify which symbologies you want the scanner to recognize. By default, the scanner is set to recognize nine of the most common symbologies. 1. Tap on the SocketScan icon. In the pop-up menu, tap Symbology Selector... 2. In the screen that appears, check the symbologies you wish to enable. Uncheck those you wish to disable. Alternatively, tap Enable All or Disable All. Tap ok. Symbologies not supported by the CRS will be grayed out. Enabling all possible symbologies will make the decode process slightly longer. CHAPTER 2: SETUP FOR WINDOWS MOBILE 19 OPTIONAL: Configure Prefix/Suffixes The SocketScan applet lets you specify prefix and/or suffix characters to be added automatically to the data you scan. This helps to further eliminate manual data entry. 1. Tap on the SocketScan icon. In the pop-up menu, tap Settings. You can configure prefix/suffixes whether or not the CRS is connected to your Pocket PC. 2. The Scanner Settings utility will appear, with the Prefix/Suffix tab open. Enter the characters you want to be appended to each scan (128 character maximum). Tap ok. Only printable ASCII characters can be used as prefixes or suffixes. The default suffix is a carriage return. 20 OPTIONAL: Run Scan Demo Scan Demo makes it easy to determine the symbology, number of characters, and decoded data (in either ASCII or Hex) of any bar code supported by the scanner. This is especially useful if you encounter a bar code that the scanner will not decode by default. 1. Tap Start | Programs | Scan Demo. Accessing Scan Demo disconnects the Bluetooth link. If you have not configured the CRS to automatically connect, select the CRS tab at the bottom of the page to re-establish this link. 2. The Scan Demo screen will appear. If desired, use the check boxes at the bottom of the screen to modify the test. Enable all symbologies: By default, this option is checked. Different symbologies can sometimes interpret the same bar code differently, so you may want to uncheck this option. Display as hex data: Check this box to view scanned data in hexadecimal format. Otherwise, data will appear as ASCII. 3. Scan the bar code. Scan Demo will report the properties of the bar code. CHAPTER 2: SETUP FOR WINDOWS MOBILE 21 Appendix A Specifications Physical Characteristics Wrist Unit Size: 98l x 13.1h x 47w (mm) 3.86l x 0.52h x 1.85w (in.) Ring Size: 55l x 37h x 38w (mm) 2.17l x 1.46h x 1.5w (in.) Total Mass: approx. 90 g (0.2 lb) Power Source: Rechargeable lithium-ion battery BL-6C Expected Battery Life with Typical Operation (connected via Bluetooth and minimum 10,000 bar code scans): 8 hours Operating Temp: -4 to 140°F (-20 to 60°C) Operating System Support: • Windows Mobile 5.0, 2003/2003SE 2005 Sunrise Date Compliant Scanning Characteristics Bar Code Symbologies Decoded: Code 39, UPC/EAN/JAN, MSI, Code 128, Code 93, Codabar, I 2 of 5, D 2 of 5, RSS-14 Laser: Class 2 with Fuzzy Logic) Scan Angle: 46.5° Laser Scanner Performance: Scan Repetition Rate: 50 (± 3) scans/sec (bi-directional) Decode Distances: 2.2 to 40+ inches depends on symbol size, symbology, label media, W-N Ratio, scan angle Bluetooth Characteristics Protocol: Bluetooth 2.45 GHz ISM band frequency hopping Antenna: Integrated Radio Range: Up to 330 ft (100 m), depending on environment Connection: Point-to-point Security: Encrypted link RF Power: Class 1 radio; Typical Output: 14 dbm 22 | APPENDIX A: SPECIFICATIONS Certification/Compliance (pending) FCC: Part 15, Class B CE: EN55024:1998 C-TICK: s.182 Industry Canada VCCI Bluetooth 1.1 IP54 TELEC About Bluetooth Range The Cordless Ring Scanner features a powerful Class 1 Bluetooth radio to provide the maximum possible range. As with all wireless technologies, the connection range can vary widely depending on many factors such as the brand and placement of the host device, the type and size of physical obstacles and the presence and activity level of competing radio transmissions. In range testing of the CRS while connected to a variety of typical host devices with Class 2 radios, functional connection distances from 18 to over 100 feet have been experienced depending on the environment. The following conditions appear to reduce the Bluetooth connection range: • The presence of soft, absorbent materials such as paper, fiberglass insulation, foam material in office cubical walls, carpeting and, to a lesser extent, even sheetrock and wood construction materials. Hard materials such as concrete increase the range. • Human bodies or containers of liquid positioned between the host and the CRS. • The presence and activity level of competing Bluetooth or 802.11 (Wi-Fi) systems using the same 2.4 GHz frequency. • Metal in a grid pattern, such as chain link fencing or chicken wire. This type of material may block the Bluetooth (or Wi-Fi) signal completely. APPENDIX A: SPECIFICATIONS 23 Appendix B Safety and Usage Tips About Bluetooth and Health Bluetooth wireless technology allows you to use short-range radio signals to connect a variety of devices, such as bar code scanners, mobile phones, Pocket PCs, notebook computers, printers, LAN access points, and many other devices at home or work. These radio signals replace the cables that have traditionally connected these devices. Bluetooth products have small radio transmitters and receivers. Output power is normally very low, only 1 mW (1/1000 of a watt). This gives a working range of approximately 10 meters. The maximum exposure levels from Bluetooth products are far below recommended safety guidelines. At most, typical Bluetooth devices (1mW) reach only one percent of the prescribed safety levels. Product Care • Do not expose your product to liquid, moisture or extreme humidity. • Do not expose your product to extreme high or low temperatures. • Do not expose your product to lit candles, cigarettes, or cigars, or to open flames, etc. • Do not drop, throw or try to bend the product, as rough treatment could damage it. • Do not paint your product, as the paint could obstruct parts and prevent normal use. • Do not attempt to disassemble your product: a broken warranty seal will void the warranty. The product does not contain consumer serviceable components. Should your Cordless Ring Scanner need service, please contact Socket technical support at: support@socketcom.com. • Treat your product with care. Keep in a clean and dust-free place. • Changes or modifications of this product, not expressly approved by Socket, may void the user’s authority to operate the equipment. Antenna Care Do not place a metallic shield around the Cordless Ring Scanner since it will reduce the radio transmission efficiency. 24 Efficient Use For optimum performance, please make sure that there is no metal surrounding your Cordless Ring Scanner. Driving RF energy may affect some electronic systems in motor vehicles, such as car stereo, safety equipment, etc. Check with your vehicle manufacturer to be sure that the Cordless Ring Scanner will not affect the vehicle’s electronics. Aircraft • Turn off your Cordless Ring Scanner before boarding any aircraft. • To prevent interference with communications systems, you must not use your Cordless Ring Scanner while the plane is in the air. • Do not use it on the ground without permission from the crew. Radio Frequency Exposure Your Cordless Ring Scanner contains a radio transmitter and receiver. When in operation, it communicates with a Bluetooth enabled mobile computer by receiving and transmitting radio frequency (RF) magnetic fields in the frequency range 2400 to 2500 MHz. The output power of the radio transmitter is 0.001 Watt. The Cordless Ring Scanner is designed to be in compliance with the RF exposure limits set by national authorities and international health agencies 1 when installed or used separately from other antennas or radio transmitters. Examples of RF exposure standards and guidelines: ICNIRP, “Guidelines for limiting exposure to time-varying electric, magnetic, and electromagnetic fields (up to 300 GHz)”, International Commission on NonIonizing Radiation Protection (ICNIRP), Health Physics, vol. 74, pp 494-533, April 1998. 99/519/EC, EU Council Recommendation on the limitation of exposure to the general public to electromagnetic fields 0 Hz – 300 GHz, Official Journal of the European Communities, July 12, 1999. ANSI/IEEE C95.1-1992, “Safety levels with respect to human exposure to radio frequency electromagnetic fields, 3 kHz to 300 GHz”, The Institute of Electrical and Electronics Engineers, Inc., New York, 1991. FCC Report and Order, ET Docket 93-62, FCC 96-326, Federal Communications Commission (FCC), August 1996. Radiocommunications (Electromagnetic Radiation Human Exposure) Standard 1999, Australian Communications Authority (ACA), May 1999. APPENDIX B: SAFETY AND USAGE TIPS 25 Appendix C Bar Code Label Specifications All bar code symbols/labels should satisfy the appropriate AIM Uniform Symbology Specification. Background Substrate: The bar code symbol should be printed on material (media) that is reflective and has a matte (not glossy) finish. A background diffuse reflectance of at least 70% to 80% is desirable for optimum contrast. Retro-reflective media should be used to obtain decode distances greater than 36 inches. Ink Color and Type: The inked bars should not exceed 25% reflectance at the wavelength that is being used for reading, whether printed with black ink or colored ink. The reflectance value should not vary more than 5% within the same character. Voids and Specks: The code should be printed clearly, free of voids, specks, blemishes and lines that could “fool” the scanner. Specks or blemishes in the white spaces, or false or missing bar sections could be interpreted by the reading equipment as part of the code. Generally, the width of such flaws is more serious than the height. Code symbols/ labels should be rejected if these defects are present. Definition: The bars in the bar code symbol should be well defined. Their edges should not be rough or fuzzy, so that the bars and spaces have the proper widths intended for the bar code symbology used. Contrast: Background reflectance (that of the substrate on which the codes are printed) should always provide a good contrast relative to the ink reflectance (that of the code bars). The difference between the two should be at least 37.5% at the wavelength used for reading. Tolerance: The ratio of the widths of bars and spaces in a bar code symbol must conform to the appropriate AIM bar code specifications and can cause problems if not correct throughout the bar code. Problems can occur when bar edges are smeared or rough, or when they exhibit voids. 26 | APPENDIX C: BAR CODE LABEL SPECIFICATIONS Appendix D Enabling or Disabling Symbologies The Cordless Ring Scanner is pre-set to automatically detect and decode (auto-discriminate) the most common bar code symbologies. To enable or disable symbologies, simply use SocketScan’s Symbology Selector. Notes: • The length of some symbologies will change after Symbology Selector is used. See Table 1. • With more symbologies enabled, the scanner must work harder to search through all the possible combinations. This may make the decoding process slightly longer. • The advanced symbology parameters listed in Table 2 can only be modified by using the SocketScan Advanced Programming Guide or the SocketScan SDK. Check Socket’s website for updates. Table 1. Default Symbologies Symbology UPC/EAN/JAN UPC-A UPC-E UPC-E1 EAN-8 EAN-13 Code 128 (USS-128 & UCC/EAN 128) Code 39* Code 39 Trioptic Code 39 Code 39 Full ASCII Code 93 Interleaved 2 of 5* Discrete 2 of 5* Codabar MSI Plessey* RSS-14 (Standard, Limited, Expanded)** Scanner Default Default Length Length after Symbology Selector Enabled Enabled Disabled Enabled Enabled Enabled N/A N/A N/A N/A N/A Any N/A N/A N/A N/A N/A Any Enabled Enabled Disabled Disabled Enabled Disabled Disabled Disabled Disabled 2 to 23 2 to 23 2 to 23 2 to 38 14 Only 12 Only 5 to 55 1 to 30 N/A 2 to 55 2 to 55 2 to 55 2 to 55 2 to 55 2 to 55 2 to 55 2 to 55 N/A *Warning: Setting the length to “Any” may lead to inaccurate decodes of these symbologies. **This symbology will be added in the next release. APPENDIX D: ENABLING/DISABLING SYMBOLOGIES 27 Table 2. Other Symbology Parameters Symbology Parameters Scanner Default UPC/EAN/JAN Supplementals Transmit Check Digit Bookland EAN Decode UPC/EAN Supplementals UPC/EAN Supplemental Redundancy Transmit UPC-A Check Digit Transmit UPC-E Check Digit Transmit UPC-E1 Check Digit Convert UPC-E to A Convert UPC-E1 to A EAN-8 Zero Extend UPC/EAN Security Level UPC/EAN Coupon Code Disabled Enabled Disabled Ignore Seven Enabled Enabled Enabled Disabled Disabled Disabled Disabled Code 39 Convert Code 39 to Code 32 Code 32 Prefix Check Digit Verification Transmit Check Digit Code 39 Full ASCII Disabled Disabled Disabled Disabled Disabled Interleaved 2 of 5 Check Digit Verification Transmit Check Digit Convert I 2 of 5 to EAN-13 Disabled Disabled Disabled RSS-14 RSS-14 Limited RSS-14 Expanded Disabled Disabled Disabled 28 For more information on bar codes, symbologies, labels or other bar code related topics, visit any of the following web sites: a. www.aimglobal.org/technologies/barcode/ b. www.aimglobal.org/aimstore/stackedsymbologies.htm c. www.adams1.com d. www.bizfonts.com e. www.barcode-us.com/info_center/upc.htm (UPC Codes) f. www.barcode-us.com/info_center/bookinfo.htm (Bookland EAN) g. www.dataid.com/bcsymbology.htm h. www.aaabarcodes.com i. www.snx.com/mechanics.html j. www.pscnet.com/html/aabcsymbologies.htm#Checksums k. www.idautomation.com/barcoding4beginners.html APPENDIX D: ENABLING/DISABLING SYMBOLOGIES 29 Appendix E Decode Zone The decode zones for the Cordless Ring Scanner is shown below. The minimum element width (“X Dimension” or bar code “size”) is the width in thousandths of an inch (mils) of the narrowest element (bar or space) in the symbol. The figures shown are the typical scanning distances (depths of field) for selected bar code sizes. The maximum usable length of a bar code symbol (Width of Field) at any given range is also shown. 30 | APPENDIX E: DECODE ZONE Appendix F Troubleshooting For help on SocketScan, tap Start | Help on a Pocket PC. icon in the task tray SYMPTOM: I get the “No Scanner Detected” of my Windows device and can’t trigger the laser or scan any bar codes. POSSIBLE REASON SOLUTION Your mobile computer is not connected to the Cordless Ring Scanner. Make sure the Cordless Ring Scanner is on and in range and has enough battery power. Try to reconnect. SYMPTOM: When I try to scan, the laser activates, but no data appears on my screen, and the laser eventually turns off. POSSIBLE REASON SOLUTION The scanner is too close or too far from the bar code. Practice so you get accustomed the most effective distance and scanning angle. Try scanning a bar code that is correctly formatted or printed well, such as on a retail package. Use Scan Demo for Windows Mobile to identify the symbology. If needed, enable the symbology by using Symbology Selector. The bar code is incorrectly formatted or poorly printed. The bar code symbology may be disabled or not supported by the Cordless Ring Scanner. SYMPTOM: My mobile computer cannot find the CRS, and/or I get an error message saying that there are connection problems. POSSIBLE REASONS SOLUTION You are too far from the Cordless Ring Scanner. The Cordless Ring Scanner is not turned on. You have assigned another device as your favorite or default Bluetooth serial device. Move the devices closer together, within a range of 10-15 meters. Turn on the Cordless Ring Scanner. Remove any settings that assign another device as your favorite Bluetooth serial device. APPENDIX F: TROUBLESHOOTING | 31 SYMPTOM: While scanning with the CRS, I turned off the Pocket PC, or my Pocket PC entered suspend mode. Now my Pocket PC won’t turn on again. POSSIBLE REASONS SOLUTION This is a known problem with the Widcomm stack (built into HP h221X iPAQ Pocket PCs with ROM version 1.00). Soft reset the Pocket PC by pressing the reset button. SYMPTOM: While scanning with the CRS, I turned off the host device, or my host device entered suspend mode. Now the CRS won’t reconnect to my host device. POSSIBLE REASONS SOLUTION There is a problem with the Broadcom (Widcomm) stack on some devices where the CRS can be discovered but fails to communicate. Affected units include the HP iPAQ models h221X with ROM version 1.10 and h1945. Soft reset the Pocket PC by pressing the reset button. 32 | APPENDIX F TROUBLESHOOTING Appendix G Technical Support If you have trouble installing or using the Socket Cordless Ring Scanner, contact Socket’s technical support department for assistance. IMPORTANT! To obtain technical support, you must first register your product online at www.socketcom.com/prodreg. After you register your product, log in and click on the Technical Support tab. Click New Trouble Ticket to submit an online request for technical support. Afterwards, you can log in anytime to monitor the status of your request. If we are unable to resolve your support inquiry online, we can arrange for a technical support representative to call you at a specific time. Please refrain from disassembling the Cordless Ring Scanner. Disassembly of this device will void the product warranty. APPENDIX G: TECHNICAL SUPPORT | 33 Limited Warranty Socket Communications Incorporated (Socket) warrants this product against defects in material and workmanship, under normal use and service, for the following period from the date of purchase: Cordless Ring Scanner: Two years Incompatibility is not a defect covered by Socket’s warranty. During the warranty period, Socket will, at its option, repair or replace the defective product at no charge when furnished with proof of retail purchase, provided that you deliver the product to Socket or to an authorized Socket Service Center. The returned product must be accompanied by a return material authorization (RMA) number issued by Socket or by Socket's Authorized Service Center. If you ship the product, you must use the original container or equivalent and you must pay the shipping charges to Socket. Socket will pay shipping charges back to any location in the contiguous United States. This warranty applies only to the original retail purchaser and is not transferable. Socket may, at its option, replace or repair the product with new or reconditioned parts and the returned product becomes Socket's property. Socket warrants the repaired or replaced products to be free from defects in material or workmanship for ninety (90) days after the return shipping date, or for the duration of the original warranty period, whichever is greater. This warranty does not cover the replacement of products damaged by abuse, accident, misuse or misapplication, nor as a result of service or modification other than by Socket. SOCKET IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, INCLUDING DAMAGE TO PROPERTY AND, TO THE EXTENT PERMITTED BY LAW, DAMAGES FOR PERSONAL INJURY. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow limitation of implied warranties, or the exclusion or limitation of incidental or consequential damages, so that the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. This product may contain fully tested, recycled parts, warranted as if new. For warranty information, call (510) 744-2700. 34 Limited Software Warranty LIMITED WARRANTY. SOCKET warrants that the original disk or CD ROM is free from defects for 90 days from the date of delivery of the SOFTWARE. CUSTOMER REMEDIES. SOCKET’S entire liability and your exclusive remedy shall be, at SOCKET’S option, either (a) return of the price paid or (b) replacement of the SOFTWARE which does not meet SOCKET’S Limited Warranty and which is returned to SOCKET with a copy of your receipt. Any replacement SOFTWARE will be warranted for the remainder of the original warranty period or 30 days, whichever is longer. THESE REMEDIES ARE NOT AVAILABLE OUTSIDE OF THE UNITED STATES OF AMERICA. NO OTHER WARRANTIES. SOCKET disclaims all other warranties, either express or implied, including but not limited to implied warranties of merchantability and fitness for a particular purpose, with respect to the SOFTWARE and the accompanying written materials. This limited warranty gives you specific legal rights. You may have others which vary from state to state. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. In no event shall SOCKET or its suppliers be liable for any damages whatsoever (including, without limitation, damages for loss of business profits, business interruption, loss of business information, or other pecuniary loss) arising out of the use of or inability to use the SOFTWARE, even if SOCKET has been advised of the possibility of such damages. Because some states do not allow the exclusion or limitation of liability for consequential or incidental damages, the above limitation may not apply to you. EXPORT LAW ASSURANCES. You may not use or otherwise export or reexport the SOFTWARE except as authorized by United States law and laws of the jurisdiction in which the SOFTWARE was obtained. In particular, but without limitation, none of the SOFTWARE may be used or otherwise exported or reexported (a) into (or to a national or resident of) a United States embargoed country or (b) to anyone on the U.S. Treasury Department’s list of Specially Designated Nationals or the U.S. Department of Commerce’s Table of Denial Orders. By using the SOFTWARE, you represent and warrant that you are not located in, under control of, or a national or resident of any such country or on any such list. GOVERNMENT END USERS. If the SOFTWARE is supplied to the U. S. Government, the SOFTWARE is classified as “restricted computer software” as defined in clause 52.227-19 of the FAR. The U. S. Government ‘s rights to the SOFTWARE are as provided in clause 52.227-19 of the FAR. CONTROLLING LAW AND SEVERABILITY. This License shall be governed by the laws of the United States and the State of California. If for any reason a court of competent jurisdiction finds any provision, or portion thereof, to be unenforceable, the remainder of this License shall continue in full force and effect. 35 Regulatory Compliance The Socket Cordless Ring Scanner is designed to be compliant with the rules and regulations in locations where they are sold and will be labeled as required. This product is type approved — users are not required to obtain license or authorization before using. This product has been certified as conforming to technological standards. Therefore, the following actions are punishable by law: • Disassembly or modification of this product • Removal of identification labels on the back of the product The frequency used by this product is also used by industrial, scientific and medical devices, such as microwave ovens, as well as wireless detectors for motion detectors, such as those requiring licenses used on manufacturing lines or similar radio transmitters (all of these wireless devices will be called “other wireless transmitters” below). Most modern electronic equipment (e.g., in hospitals and cars), is shielded from RF energy. However, certain electronic equipment is not. 1. Please ensure that all medical devices used in proximity to this device meet appropriate susceptibility specifications for this type of RF energy. 2. In the unlikely event that there is electronic interference between this system and other wireless transmitters, quickly change the location of operation or stop operating the unit (cease signal transmission). 3. If other electrical interference or related problems occur, contact Socket technical support at support@socketcom.com Radio Frequency Interference Requirements This device complies with part 15 of the FCC rules and Industry Canada. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment is also ETS EN300 328-2, ETS EN301 489-1 and ETS EN301 489-17 compliant. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his or her own expense. 36 This equipment generates and radiates radio-frequency energy. To comply with FCC RF exposure compliance requirements, the following antenna installation and device operating configurations must be satisfied: (1) Users are not permitted to make changes or modify the system in any way, and (2) connecting external antennas to the Cordless Ring Scanner is prohibited. This device and its antenna must not be co-located or operated with any other antenna or transmitter. To comply with Industry Canada RF exposure compliance requirements, the following antenna installation and device operating configurations must be satisfied: “The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, available at Health Canada’s website www.hc-sc.gc.ca/ehp/ehd/catalogue/rpb.htm” If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user may try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna of the radio or television. • Increase the distance separating the equipment and the receiver. • Connect the equipment to an outlet on a different branch circuit than that of the receiver. • Consult the dealer or an experienced radio/TV technician for help. The user may find the following booklet helpful: How to Identify and Resolve Radio-TV Interference Problems. This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402. Canada Certification The marking of “IC:xxxxxx-yyyyyy” on the device means: “xxxxxxyyyyyy” is the certification number, and the term “IC’ before the equipment certification number only signifies that Industry Canada technical specifications were met. Radio Frequency Interference Requirements – Canada This Class B digital apparatus meets the requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la Classe B respecte toutes les exigencies du Reglement sur le Matériel Brouilleur du Canada. 37 CE Marking & European Union Compliance Products intended for sale within the European Union are marked with a CE Mark which indicates compliance to applicable Directives and European Normes (EN), as follows. Amendments to these Directives or ENs are included: Normes (EN), as follows: Applicable Directives: • Radio and Telecommunications Terminal Equipment Directive 1999/5/EC • Low Voltage Directive 73/23/EEC Applicable Standards: • EN 55 022 – Limits and Methods of Measurement of Radio Interference Characteristics of Information Technology Equipment. • EN 50 082-1 – Electromagnetic Compatibility – General Immunity Standard, Part 1: Residential, Commercial, Light Industry. • IEC 801.2 – Electromagnetic Compatibility for Industrial Process Measurement and Control Equipment, Part 2: Electrostatic Discharge Requirements. • IEC 801.3 – Electromagnetic Compatibility for Industrial Process Measurement and Control Equipment, Part 3: Radiated Electromagnetic Field Requirements. • IEC 801.4 - Electromagnetic Compatibility for Industrial Process Measurement and Control Equipment, Part 4: Electrical Fast Transients Requirements • EN 60 950 + Amd 1 + Amd 2 – Safety of Information Technology Equipment Including Business Equipment. LASER DEVICE: Class 1 laser devices are not considered to be hazardous when used for their intended purpose. The following statement is required to comply with U.S. and international regulations: CAUTION: Use of controls, adjustments or performance of procedure other than those specified herein may result in hazardous laser light exposures. Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful. 38 Battery Warning: • Your device contains a rechargeable Lithium-Ion battery. Never throw the battery into a fire, as that could cause the battery to explode. • Never short-circuit the battery by bringing the terminals in contact with another metal object. This could cause personal injury or a fire, and could also damage the battery. • Never dispose of used battery with other ordinary solid wastes. Batteries contain toxic substances. • Dispose of used battery in accordance with the prevailing community regulations that apply to the disposal of batteries. Cover the metal terminals with insulating tape. (This is to prevent accidental shortcircuiting). • Never expose the battery to any liquid. • Always keep the battery out of reach of infants or small children. • Never shock the battery by dropping it or throwing it. • Dispose of a spent or damaged battery promptly. Product Disposal Your device should not be placed in municipal waste. Please check local regulations for disposal of electronic products. 39 © Socket Communications, Inc. 4/2006 Printed in U.S.A.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Encryption : Standard V2.3 (128-bit) User Access : Print, Copy, Annotate, Fill forms, Extract, Print high-res Tagged PDF : Yes XMP Toolkit : 3.1-702 Producer : Acrobat Distiller 7.0.5 (Windows) Company : Socket Communications Source Modified : D:20060420233919 Creator Tool : Acrobat PDFMaker 7.0.7 for Word Modify Date : 2006:04:20 16:43:25-07:00 Create Date : 2006:04:20 16:39:37-07:00 Metadata Date : 2006:04:20 16:43:25-07:00 Document ID : uuid:766bbf33-eabf-4183-a207-f0cefe2ec0b0 Instance ID : uuid:bb8bca49-49a5-4896-a0f9-46a68ca39dbc Version ID : 6 Format : application/pdf Title : Socket Cordless Ring Scanner User's Guide Creator : Michelle Man Headline : Page Count : 40 Page Layout : OneColumn Author : Michelle ManEXIF Metadata provided by EXIF.tools