Somfy Systems DECOFLEX DECOFLEX RTS Switch User Manual decoflex
Somfy Systems DECOFLEX RTS Switch decoflex
User manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 914375 |
| Application ID | W6XxOg6BXXvqIhjjTlF5tA== |
| Document Description | User manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 41.96kB (524464 bits) |
| Date Submitted | 2008-03-13 00:00:00 |
| Date Available | 2008-03-13 00:00:00 |
| Creation Date | 0000-01-01 00:00:00 |
| Producing Software | Corel PDF Engine Version 3.0.0.576 |
| Document Lastmod | 2008-03-08 20:00:26 |
| Document Title | decoflex.cdr |
| Document Creator | CorelDRAW |
| Document Author: | TERRI_O |
DECOFLEX RTS SWITCH Operating Instructions The DecoFlex RTS Switch is a wireless radio transmitter compatible with all Somfy RTS Motors and externally mounted RTS receivers. DESCRIPTION White: 1810813 Ivory: 1810814 Black: 1810830 - Commands are transmitted by radio waves at 433.42 MHz. - Power: 3V lithium battery, CR 2450 type - Operating temperature: +5oC/41oF to +40oC/104oF - Range: Up to 65 Ft. - Fits into standard Decora Wall Plates This is a low voltage device which does not need to be mounted inside an electrical box. It can be mounted adjacent to an existing Decora style light switch or as a stand alone device using the specific SOMFY low voltage bracket (included). PROGRAMMING FIGURE 1 A. ADDING A DECOFLEX RTS WALL SWITCH - INITIAL INSTALLATION IMPORTANT: for initial programming provide power only to the motor or receiver being programmed 1. Set the RTS Receiver or Motor into its Programming Mode (Refer to the installation instructions of the relevant RTS receiver or motor for this procedure). 2. Select the Channel to be memorized by pressing the appropriate button. The button will light. Refer to Figure 1. 3. Using a paperclip or similar device, briefly press the programming button (1 sec max) located on the DecoFlex Switch 4. The receiver/motor will confirm the addition of the new DecoFlex Switch in their respective manners. Select the Channel Programming Button B. ADDING MULTIPLE DECOFLEX WALL SWITCHES 1. Place the receiver or motor into programming mode by pressing and holding the programming button (for 3 sec.) of a DecoFlex switch or Telis Transmitter that has been previously memorized. There is no need to access the external receiver for this operation. 2. The receiver/motor will confirm PROGRAMMING MODE in their respective manners. 3. Select the NEW channel or RTS Switch to be memorized. Press the programming button (1 sec. max.) on the DecoFlex RTS switch. 4. The receiver/motor will confirm the addition of the new RTS Switch or Channel in their respective manners. C. REMOVING A DECOFLEX RTS SWITCH FROM THE MOTOR OR RECEIVERâS MEMORY 1. Place the receiver or motor into programming mode by pressing and holding the programming button (for 3 sec.) of a DecoFlex RTS Switch or Telis Transmitter that has been previously memorized. It should NOT be the one to be removed from memory. 2. The receiver/motor will confirm PROGRAMMING MODE in their respective manners. 3. Select the RTS Switch or Channel to be removed from memory. Press the programming button (1 sec. max.) on the RTS switch. 4. The receiver/motor will confirm the removal of the RTS Switch or Channel in their respective manners. OPERATION FIGURE 2 1. Select the channel of the window treatment to be operated by pressing the appropriate button. The button will light. Refer to Figure 2. 2. To raise the window treatment, press the UP button. Similarly, to lower the window treatment, press the DOWN button. 3. To stop the window treatment at any time, simply press the STOP button. Select the Channel STOP Button DOWN Button SOMFY CANADA SOMFY SYSTEMS, INC. 6315 Shawson Drive, Unit #1 Mississauga, Ontario L5T1J2 47 Commerce Drive Cranbury, NJ 08512 SOMFY SYSTEMS, INC. reserves the right to change, update or improve this document without prior notice. Ref. No. 2501819 UP Button C SOMFY SYSTEMS, INC. 3/08 4 MOUNTING METHOD The special SOMFY low voltage bracket is specifically designed to mount the DecoFlex RTS wall switch next to an existing Decora light switch with an electrical box already behind the drywall. This bracket differs from other off-the-shelf low voltage brackets because it is offset on one side. This allows a double gang Decora style cover plate to fit over both switches without installing a double gang electrical box behind the drywall. It is also possible to mount this bracket as a stand alone low voltage device. INSTALLATION PROCEDURE NOTE: This bracket is designed for an existing electrical box already behind the sheetrock. If a retrofit electrical box was used, it is recommended to remove the single gang and replace it with a double gang retrofit box. 1. Orient the brackets flat side against the wall keeping the thin side closest to and centered with the existing electrical switch box. 1 5/8 2. Align the inside edge of the thin side of the bracket with 3. Cut traced opening into drywall. Be careful not to make the opening larger than the outside edge of the switch box. Then trace the necessary, to ensure a tight fit. Use inside shape (as shown by the dashed line in the dimensions in diagram below. Do not exceed diagram) of the bracket. (sheetrock not shown for clarity) these dimensions to ensure a proper fit of the bracket wood 2x4 Existing Electrical Box 3 7/16 3 7/16 Inside Edge thin side of bracket 5. To keep the bracket in place, bend tabs 90o around drywall, as tightly as possible. 6. Mount low voltage switch into bracket, with its edge flush against electrical switch box. 7. Finish the installation by mounting a standard double gang Decora switch cover plate, over both switches. 2.61 4. Insert bracket (as shown) into hole, keeping the thin side closest to the existing switch box, and laying flat on drywall. 1 5/8 1.30 drywall BATTERY LIFE The DecoFlex RTS Switches are powered by a 3V battery (type 2450) which provides about 25 years operation assuming 4 operations per day. When the battery becomes discharged, the control LED no longer lights up when a command is sent, and the command is not carried out. HOW TO REPLACE THE BATTERY 1. Remove the screws on the back cover of the RTS Switch. 2. Slide the battery out of its holder by pushing it with a screwdriver. 3. Insert the new battery, maintaining its correct polarity. NOTE: Do not throw the battery in the trash, but dispose of it properly. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (i). This device may not cause harmful interference, and (ii). This device must accept any interference received, including interference that may cause undesired operation. G
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Create Date : 0000:01:01 00:00:00Z Modify Date : 2008:03:08 20:00:26-05:00 Page Count : 3 Creation Date : 0-01-01T00:00:00Z Mod Date : 2008:03:08 20:00:26-05:00 Producer : Corel PDF Engine Version 3.0.0.576 Author : TERRI_O Metadata Date : 2008:03:08 20:00:26-05:00 Creator : TERRI_O Title : decoflex.cdrEXIF Metadata provided by EXIF.tools