Somfy Systems SWF Sunis RTS Wirefree Sun Sensor 9020412 User Manual SUNIS RTS 9020412 Draft 3 6 17
Somfy Systems Sunis RTS Wirefree Sun Sensor 9020412 SUNIS RTS 9020412 Draft 3 6 17
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3344325 |
| Application ID | KVeEapdfn+TRiZ7ZG/wbaQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 148.96kB (1861970 bits) |
| Date Submitted | 2017-04-04 00:00:00 |
| Date Available | 2017-04-04 00:00:00 |
| Creation Date | 2017-03-16 12:51:43 |
| Producing Software | Corel PDF Engine Version 17.6.0.1021 |
| Document Lastmod | 2017-03-16 12:51:43 |
| Document Title | SUNIS RTS 9020412 Draft 3-6-17.cdr |
| Document Creator | CorelDRAW X7 |
| Document Author: | Sanders Glen |
Introduction: The SUNIS RTS sun sensor provides control of your RTS motorized products based on current sun light levels. It can provide maintenance free service for 5+ years from 2 AA batteries. The precise sun level can easily be selected with 8 possible levels of light sensitivity. The sun function can be enabled/disabled via a Somfy Soliris RTS transmitter or MyLink. A Somfy Soliris RTS transmitter or MyLink must be provided with each installation to enable/disable the sun function. www.somfysystems.com Overview GETTING STARTED Green LED Level 5-8 Green Prog LED Red Batt LED Prog Button Sun Level Sun Level Red LED Level 1-4 The mounting location is critical Fig 4. Mount the Sunis RTS facing the direction the awning/screen protects from sun. Ensure it is clear from obstruction that could shade it through out the day. Programming: Programming Button Opening the Sunis RTS: ■ Wirefree, no electrician required ■ Easily select from 8 levels for sun threshold setting OUTDOOR SUNIS RTS WIREFREE Sun Sensor 9020412 ■ Long battery life ■ DEMO mode for fast and easy testing ■ LED feed back for all functions ■ Compatible with full range of RTS exterior motors ■ Ideal for new and existing installations FCC: EN This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: - This device may not cause harmful interference and - This device must accept any interference received, including interference that may cause undesired operation Warning! Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment. Installer Manual Safety: www.somfysystems.com SOMFY SYSTEMS INC SOMFY NA HEADQUARTERS 121 Herrod Blvd. Dayton, NJ 08810 P: (800) 22-SOMFY (76639) NJ: (609) 395-1300 F: (609) 395-1776 FLORIDA 6100 Broken Sound Pkwy. N.W. Suite 14 Boca Raton, FL 33487 P: (800) 22-SOMFY (76639) F: (561) 995-7502 CALIFORNIA 15291 Barranca Parkway Irvine, CA 92618-2201 P: (800) 22-SOMFY (76639) F:(949) 727-3775 SOMFY ULC SOMFY Canada Division 5178 Everest Drive Mississauga, Ontario L4W2R4 P: (800) 66-SOMFY (76639) CN: (905) 564-6446 F: (905) 238-1491 IC statements: - This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired Operation of the device. - Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Copyright © 3/2017 Somfy Systems Inc./SAS. All rights reserved. Before installing and using this product, please read these instructions carefully. Moreover, the installer must comply with current standards and legislation in the country in which the product is being installed, and inform his customers of the operating and maintenance conditions for this product. Any use outside the field of application specified by Somfy invalidates the warranty and discharges Somfy of all liability, as does any failure to comply with the instructions given herein. Before installing please check the compatibility of this product with the associated equipment and accessories. Fig 5 Adding the Sunis RTS to the motor(s): Fig 1 Fig 2 Rotate the top clockwise to align the arrows on the base and sensor top Fig1. This will allow you to open the sensor by lifting the sensor top from the mounting base Fig 2. Batteries: Battery Red LED Fig 2 Two AA Alkaline Install the batteries paying attention to the polarity shown on the base Fig 2. If the batteries are good and installed correctly, the RED battery LED will blink just after the batteries are installed. Hint: You can also check if batteries are still good by removing them and reinstalling and confirming the battery LED blinks. Installation: Fig 3. What is in the box: 1. Sunis RTS sensor with built in mounting base 2. 2 AA alkaline batteries 3. 2 mounting screws Deleting the sensor - Repeat steps 1 and 2 above. Hints: A Soliris transmitter or MyLink must be programmed to the motor(s) to allow the user to Enable/Disable the sun Function. If a sensor is removed or damaged, it must be cleared from the motor memory. To delete all sensors when adding a new sensor, follow steps 1 and 2 above except on step 2 hold the prog button until the motor jogs twice (approx 7 sec). This Will clear all sensors. Repeat steps 1 and 2 normally to add the new sensor. Increase Threshold Setting Sun Threshold Level: Sunlight intensity (kLux) LED active . Never drop, knock, drill or submerge the SUNIS. . Do not use abrasive products or solvents to clean the SUNIS RTS Specifications: Power In: AA Alkaline Battery Maximum Range: 65 ft. under optimal conditions Operating Temperature: -4oF to 104oF (-20oC to +40oC) IP34 rated for direct weather exposure (Must be mounted correctly as per mounting instructions) Step 1: Press the programming button on the RTS transmitter for 3+ sec until the motor jogs. Fig 5 Step 2: Press the Prog button on the Sunis RTS. Fig 6 The green Prog LED will light and the motor will jog. The Sunis RTS has been added to the motor. Thresholds 1 2 3 4 5 6 7 8 Specific safety advice: SUNIS RTS . Do not clean it using a water spray or high pressure cleaning methods. . Ensure that the receiver is kept clean and regularly check if it is operating correctly. Fig 6 5 10 20 40 55 75 100 Red Decrease Threshold Green ☆ ★ ☆ ★ Number of ☆ ☆ ★ ★ ☆ ☆ ★ ★ ☆ ☆ ★ ★ flashes ☆ ★ ☆ ★ For exterior use, the Sunis RTS must be mounted to a vertical wall. Drill 2 holes 17mm apart Fig 3.1. Mount the Sunis RTS base with the up arrow facing up and the drain hole facing directly down Fig 3.2. Fig4 The Sun Threshold level can be adjusted up or down by a short press of the + or - button. For levels 1-4 the orange LED will blink 1 - 4 times to confirm the level. For levels 5-8 the green LED will blink. DEMO Mode: ☆ ★ Time Delays No Sun Sun Normal Mode 15-30 min 2 min Demo Mode 15 sec 10 sec Demo mode allows the Sunis RTS to be more easily tested by reducing the delay times. Pressing the + & together will cause the Sunis to cycle in or out of Demo. The Red and Green LEDs will alternate when entering Demo mode and blink together when exiting. The Sunis Will automatically time out of Demo mode in 3 min.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Profile CMM Type : Lino Profile Version : 2.1.0 Profile Class : Display Device Profile Color Space Data : RGB Profile Connection Space : XYZ Profile Date Time : 1998:02:09 06:49:00 Profile File Signature : acsp Primary Platform : Microsoft Corporation CMM Flags : Not Embedded, Independent Device Manufacturer : IEC Device Model : sRGB Device Attributes : Reflective, Glossy, Positive, Color Rendering Intent : Perceptual Connection Space Illuminant : 0.9642 1 0.82491 Profile Creator : HP Profile ID : 0 Profile Copyright : Copyright (c) 1998 Hewlett-Packard Company Profile Description : sRGB IEC61966-2.1 Media White Point : 0.95045 1 1.08905 Media Black Point : 0 0 0 Red Matrix Column : 0.43607 0.22249 0.01392 Green Matrix Column : 0.38515 0.71687 0.09708 Blue Matrix Column : 0.14307 0.06061 0.7141 Device Mfg Desc : IEC http://www.iec.ch Device Model Desc : IEC 61966-2.1 Default RGB colour space - sRGB Viewing Cond Desc : Reference Viewing Condition in IEC61966-2.1 Viewing Cond Illuminant : 19.6445 20.3718 16.8089 Viewing Cond Surround : 3.92889 4.07439 3.36179 Viewing Cond Illuminant Type : D50 Luminance : 76.03647 80 87.12462 Measurement Observer : CIE 1931 Measurement Backing : 0 0 0 Measurement Geometry : Unknown Measurement Flare : 0.999% Measurement Illuminant : D65 Technology : Cathode Ray Tube Display Red Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Green Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Blue Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Page Count : 1 Create Date : 2017:03:16 12:51:43-04:00 Modify Date : 2017:03:16 12:51:43-04:00 Producer : Corel PDF Engine Version 17.6.0.1021 Author : Sanders Glen Creator : CorelDRAW X7 Title : SUNIS RTS 9020412 Draft 3-6-17.cdrEXIF Metadata provided by EXIF.tools