Sonicwall 06E Access Point 802.11 a/b/g/n User Manual

Sonicwall, Inc. Access Point 802.11 a/b/g/n

Contents

User manual

SonicPoint-Ne / SonicPoint-Ni Getting Started GuideSonicPoint_N_GSG.book Page 1 Friday, June 4, 2010 3:08 PMSonicWALL APL21-06E /APL21-083
SonicWALL SonicPoint Getting Started Guide Page 1SonicWALL SonicPoint-Ne / SonicPoint-NiGetting Started GuideThis Getting Started Guide provides instructions for basic installation and configuration of the SonicWALL SonicPoint-Ne / SonicPoint-Ni wireless appliances in single-unit or distributed wireless deployments.SetupAdditional Configuration and InformationSupport and Training Options - page 31Product Safety and Regulatory Information - page 37Step Procedure Est. TimeBefore You Begin - page 3Introduction to Secure Wireless - page 7Registering Your Appliance - page 13Configuring Your UTM Appliance for Wireless - page 17Setting Up Your SonicPoint - page 2312345SonicPoint_N_GSG.book Page 1 Friday, June 4, 2010 3:08 PM
Page 2 SonicPoint Top Panel / Status LEDs SonicPoint Top Panel / Status LEDslinkwlanlanactlinkact Antenna Connections (SonicPoint-Ne Only)linkwlanlanactlinkactStatus LEDsPowerTest SafeModeWireless LinkWireless Activity1000mbps 100mbps 10MbpsEthernet Activitylinkwlanlanactlinkact console lanPower Port(SonicPoint-Ne only)Provides 12VDC power connectionLAN/PoE PortProvides Power over Ethernet (PoE)and Ethernet connectionConsole PortProvides management connection usingCLI->DB9 cable (for command line management only)Reset ButtonPress and hold to manually resetSonicPoint_N_GSG.book Page 2 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 31Before You BeginIn this Section:This section provides a basic checklist of materials and information you will need before you begin.•Check Package Contents - page 4•What You Need to Begin - page 51SonicPoint_N_GSG.book Page 3 Friday, June 4, 2010 3:08 PM
Page 4 Check Package Contents Check Package ContentsBefore continuing, ensure that your SonicPoint package contains the following materials: Any Items Missing?If any of the items corresponding to your product are missing from the package, please contact SonicWALL support.A listing of the most current support documents are available online at: <http://www.sonicwall.com/us/support.html>SonicPoint-Ne Appliance Checklist SonicPoint-Ni Appliance ChecklistThis Getting Started Guide DocumentSonicPoint-Ne ApplianceMounting Kit (Ceiling Braces, Anchor and Screw Kit)Front LED/Logo Cover PlateAntennas (3)Power Adaptoraa. The included power cord is intended for use in North America only.This Getting Started Guide DocumentSonicPoint-Ni ApplianceMounting Kit (Ceiling Braces, Anchor and Screw Kit)Front LED/Logo Cover PlateSonicPoint_N_GSG.book Page 4 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 5What You Need to BeginThe SonicWALL SonicPoint-Ne/Ni security appliances are centrally managed by SonicWALL NSA E-Class appliances. For more information on deploying this SonicPoint with SonicWALL NSA series and TZ series platforms, contact your local SonicWALL sales representative for the supported SonicOS releases. SonicPoints receive auto-firmware updates from the central gateway SonicWALL, this device supports SonicOS 5.6.0.3 or higher releases.In addition to the above SonicOS firmware and hardware requirements, ensure that your network deployment includes:• An 802.3af compliant PoE injector or PoE-capable switch (optional when using the SonicPoint-Ne)• An active Internet connection• A configured interface on the SonicWALL security appliance set to a zone type of “wireless”• A location selected for placement of your SonicPoint such as a wall or ceiling• Clients capable of 802.11n wireless communications11. Although clients with 802.11a/b/g hardware are supported, the presence of these legacy clients within range of your network may affect the connectionspeed of your 802.11n clients.SonicPoint_N_GSG.book Page 5 Friday, June 4, 2010 3:08 PM
Page 6 SonicPoint_N_GSG.book Page 6 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 72Introduction to Secure WirelessIn this Section:This section contains excerpts from the SonicWALL Secure Wireless Network Integrated Solutions Guide. The content is meant to provide a brief introduction to Radio Frequency (RF) technology as it pertains to different deployment scenarios.•Wireless RF Introduction - page 8•Placing Access Points - page 10•SonicWALL Wireless Firewalling - page 122SonicPoint_N_GSG.book Page 7 Friday, June 4, 2010 3:08 PM
Page 8 Wireless RF Introduction Wireless RF IntroductionThere are currently four widely adopted standards for 802.11 wireless network types: a, b, g, and n. Although 802.11n is the newest and highest capacity standard, each of the four standards has its own strengths and weaknesses. This section provides overviews of these standards.The following section provides a brief overview of RF technologies:•Frequency Bands and Channels - page 8•802.11 Comparison Chart - page 8•Radio Frequency Barriers - page 9•RF Interference - page 9Frequency Bands and ChannelsTo allow multiple separate wireless networks in a shared and confined space, the RF medium is divided into channels. For devices in the 5GHz range (802.11a), this means the possibility of up to 23 discrete channels. For devices using the 2.4GHz range (802.11b, 802.11g), the wireless space is limited to a maximum of 14 overlapping channels. As a result of these overlapping channels, 2.4GHz technology provides only a total of three discrete channels. The newer 802.11n technology does not fit into either of these categories, as it is capable of using both 2.4GHz and 5GHz, but is limited to 14 overlapping channels for backward compatibility.802.11 Comparison ChartThe following table compares signal characteristics as they apply to the current 802.11 standards:802.11a 802.11b 802.11g 802.11n# of Channels in USA 23 11 11 11# of Channels in EU 23 13 13 13# of Channels in Japan 15 14 14 14Frequency Band 5GHz 2.4GHz 2.4GHz 2.4/5GHzMax. Data Rate 54Mbps 11Mbps 54Mbps 150Mbps300Mbpsaa. Full 300Mbps throughput is possible only in environments free from 2.4Ghz interference.Note: Although 802.11b/g/n standards provide between 11 and 14 channels, only 3 of those channels are fully discrete (non-overlapping) channels.For more information on this topic, refer to the SonicWALL Secure Wireless Networking Integrated Solutions Guide.Radius (Range) 90ft/25m 120ft/35m120ft/35m300ft/90mSonicPoint_N_GSG.book Page 8 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 9Radio Frequency BarriersDetermining the location of RF barriers can be a painful part of the placement process, but keep in mind that they can be used beneficially in an attempt to block signals where you do not want coverage. The following tables list some common RF barrier types:RF InterferenceRF interference from home, office, and medical equipment is a common source of frustration in wireless deployments from the smallest home office to the largest multi-building campus.The following table lists several common sources of RF interference:Barrier Type RF Signal BlockingOpen air Very LowGlass, drywall, cube partitions LowStone floors and walls (brick/marble/granite) MediumConcrete, security glass, stacked books/paper HighMetal, metal mesh (chicken wire), re-enforced concrete, waterVery HighFaraday cage Extremely HighInterference Source Possible RF InterferenceBand(s) Affected2.4GHz phones Entire range (hundreds of feet)802.11b/g/nBluetooth devices Within 30 feet 802.11b/g/nMicrowave ovenaa. Most newer model microwave ovens have sufficient shielding to negate possible RF interference.Within 10-20 feet 802.11b/g/nScientific and medical equipmentShort distance, varies 802.11b/g/nOff-network access pointsEntire range AllRF reflective objects Long-range wireless bridgingAllSonicPoint_N_GSG.book Page 9 Friday, June 4, 2010 3:08 PM
Page 10 Placing Access Points Placing Access PointsPhysical placement of an access point has a measurable effect on who can and cannot access your wireless signal. The following sections provide an overview of wireless access point placement, signal strength, and signal direction in common wireless deployment situations:•Making Hardware Decisions - page 10•Solutions to RF Interference and Barriers - page 11Tip: For the latest SonicPoint wireless deployment information from switching recommendations tosite survey, see the SonicWALL SonicPoint Deployment Best Practices Guide at: <http://www.sonicwall.com/us/support.html>Making Hardware DecisionsThe first decision in hardware is the access point. While access point technology (802.11a/b/g/n) is one factor in determining your placement, based on distance served and bandwidth needed, taking note of other hardware-based factors is just as important. Some of the more important hardware decisions include:•Number of access points versus user density – If too many users are serviced by a single access point, maximum transfer rates are reached and that point may become a bottleneck for the whole system.•Bandwidth – How much data is moving upstream and downstream for a given type of user?•Ethernet cabling – Where are you running the powered Ethernet (PoE) cable to and how are you securing that cable. Is your PoE switch able to power all access points?•Hubs / Switches / UTM – Your wireless deployment has to tie back into your UTM appliance and LAN resources at some point. What speed is needed for your Ethernet connection to accommodate the number of access points you are installing? Also consider where your key networking devices are deployed and how they will connect efficiently with your wireless appliances.•Upgrade your Ethernet connections for 802.11n – In most cases, 802.11n wireless hardware requires more bandwidth than a single (or even dual) 10/100 Ethernet connection can handle. Gigabit Ethernet connectivity between the WLAN and the LAN is required to take full advantage of 802.11n speed.•Power up that PoE for 802.11n – Part of your wireless network planning should include verifying that your PoE equipment is 802.3af compliant, and that a full 15 watts of power can be supplied to each SonicPoint.SonicPoint_N_GSG.book Page 10 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 11Solutions to RF Interference and BarriersThese days, finding an environment with no RF interference or noise is nearly impossible. Only if you are setting up an office in a secluded redwood grove can you count on RF interference to be a non-issue. Even then, the redwood trees might just be among those fitted with high-gain cellular antennas, an all-too-common occurrence today. Regardless, you should expect to deal with some level of signal interference in your deployment. Location A – Rogue access points or wireless test lab•Problem – Wireless product test labs and other (non-malicious) rogue access points are problems in many Wi-Fi deployments. •Solution – Either eliminate all rogue access points, or force their owners to use a set channel that does not overlap with your distributed wireless solution. Location B – Spectrum noise for 2.4 GHz and 5 GHz•Problem – Your phone system is partially wireless and uses the 2.4GHz spectrum. •Solution – Give VoIP a try. VoIP will work in tandem with your wireless network, instead of against it. For more on SonicWALL VoIP implementation and capabilities, refer to the Configuring VoIP SonicOS feature module available at: http://www.sonicwall.com/us/support.htmlLocation C – Off-network access points •Problem – Your neighbors need wireless, too! Unfortunately, only a few sheets of drywall separate you. Solution – Overpowering your neighbors with high-gain antennas is an option, but not a particularly neighborly one. Instead, you could simply use a different channel for wireless access points bordering this wall and ensure that your neighbors do the same. Performance in some dual-channel wireless devices may take a hit, but it is better than dropped connections—or unhappy neighbors.ACBSonicPoint_N_GSG.book Page 11 Friday, June 4, 2010 3:08 PM
Page 12 SonicWALL Wireless Firewalling SonicWALL Wireless FirewallingWhen a wireless device uses an access point to communicate with a device on another subnet or on a completely different network, traffic between the devices is forced to traverse the network gateway. This traversal enables Unified Threat Management (UTM) services to be enforced at the gateway.Standard practice for wireless firewalling (where one wireless client is communicating with another) bypasses many of the critical UTM security services. The illustration below shows the standard practice for wireless firewalling. Many security products on the market share this potential vulnerability when two users connected by a common hub or wireless access point wish to exchange data.SonicWALL addresses this security shortcoming by managing the SonicPoint access points from the UTM appliance. This allows complete control of the wireless space, including zone enforcement of security services and complete firewalling capabilities, as shown in the illustration below.WLAN ZoneSecurity Services?Content Filtering ServiceClient Anti-Virus EnforcementGateway Anti-VirusGateway Anti-SpywareIntrusion Prevention ServiceOther Security ApplianceWLAN Zone Security ServicesSonicWALLapplianceSonicWALLSonicPointContent Filtering ServiceClient Anti-Virus EnforcementGateway Anti-VirusGateway Anti-SpywareIntrusion Prevention ServicelinkwlanlanactlinkactSonicPoint_N_GSG.book Page 12 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 133Registering Your ApplianceIn this Section:This section provides instructions for registering your SonicWALL SonicPoint appliance.•Creating a MySonicWALL Account - page 14•Registering and Licensing Your Appliance on MySonicWALL - page 14•Using SonicWALL UTM Security Services for Wireless Clients - page 15Note: Registration is an important part of the setup process and is necessary to receive the full benefits of SonicWALL security services, firmware updates, and technical support.3SonicPoint_N_GSG.book Page 13 Friday, June 4, 2010 3:08 PM
Page 14 Creating a MySonicWALL Account Creating a MySonicWALL AccountA MySonicWALL account is required for product registration. If you already have an account, continue to the Registering and Licensing Your Appliance on MySonicWALL section.To create a MySonicWALL account:1. In your browser, navigate to www.mysonicwall.com.2. In the login screen, click the Not a registered user? link.3. Complete the Registration form and click Register.4. Verify that the information is correct and click Submit.5. In the screen confirming that your account was created, click Continue.Registering and Licensing Your Appliance on MySonicWALLYou must register your SonicWALL security appliance on MySonicWALL to enable full functionality. To register your SonicPoint, perform the following tasks:1. Login to your MySonicWALL account. If you do not have an account, you can create one at www.mysonicwall.com.2. Enter the serial number of your product in the REGISTER A PRODUCT field and click the Next button.3. Type a friendly name for the appliance, select the Product Group if any, type the authentication code into the appropriate text boxes, and then click Register.4. On the Product Survey page, fill in the requested information and then click Continue.5. To pair your SonicPoint with a SonicWALL UTM appliance, navigate to the Service Management page by clicking on the device you wish to pair with your SonicPoint.6. Scroll to the Associated Products section and click the SonicWALL SonicPoint link to associate your SonicPoint with the appliance.SonicPoint_N_GSG.book Page 14 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 15Using SonicWALL UTM Security Services for Wireless ClientsAny security services you purchased for your SonicWALL UTM appliance can also be applied to wireless clients. Simply enable the security services on the WLAN zone or on a custom wireless zone, and your wireless traffic will be protected along with your wired traffic. If you have not yet purchased a security service subscription for your SonicWALL UTM appliance, please speak with a sales representative or visit www.mysonicwall.com to register for free trials.• To try a Free Trial of a service, click Try in the Service Management page.• To purchase a product or service, click Buy Now in the Service Management page.If you recently purchased security services, you will receive an activation key. This key is emailed to you after online purchases, or is on the front of the certificate that was included with your purchase. To activate existing licenses:1. Log into mysonicwall.com and navigate to the My Products page.2. Select the registered product you want to manage. 3. Locate the product on the Service Management page and click Enter Key in that row.4. In the Activate Service page, type or paste your key into the Activation Key field and then click Submit. When activation is complete, MySonicWALL displays an activation screen with service status and expiration information. You have successfully registered your SonicWALL appliance, and now you need to enable UTM security services on the SonicWALL appliance itself. SonicWALL UTM security services are not enabled by default.SonicPoint_N_GSG.book Page 15 Friday, June 4, 2010 3:08 PM
Page 16 Using SonicWALL UTM Security Services for Wireless Clients SonicPoint_N_GSG.book Page 16 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 174Configuring Your UTM Appliance for WirelessIn this Section:This section provides instructions for configuring the SonicWALL UTM appliance to connect with your SonicWALL SonicPoint.•An Introduction to Zones and Interfaces - page 18•Configuring Wireless Access - page 184SonicPoint_N_GSG.book Page 17 Friday, June 4, 2010 3:08 PM
Page 18 An Introduction to Zones and Interfaces An Introduction to Zones and InterfacesZones split a network infrastructure into logical areas, each with its own set of usage rules, security services, and policies. Most networks include multiple definitions for zones, including those for trusted, untrusted, public, encrypted, and wireless traffic.Some basic (default) zone types include:WAN - Untrusted resources outside your local networkLAN - Trusted local network resourcesWLAN - Local wireless network resources originating from SonicWALL wireless enabled appliancesDMZ - Local network assets that must be accessible from the WAN zone (such as Web and FTP servers)VPN - Trusted endpoints in an otherwise untrusted zone (such as the WAN)The security features and settings configured for the zones are enforced by binding a zone to one or more physical interfaces (such as, X0, X1, or X2) on the SonicWALL UTM appliance.The X1 and X0 interfaces are preconfigured as WAN and LAN respectively. The remaining ports (X2-X6) are also LAN ports by default. However, these ports can be configured to meet the needs of your network, either by using basic zone types (WAN, LAN, WLAN, DMZ, VPN) or configuring a custom zone type to fit your network requirements (for example: Gaming Console Zone, Wireless Printer Zone, Wireless Ticket Scanner Zone).Configuring Wireless AccessThis section describes how to configure SonicPoints with a SonicWALL UTM appliance. SonicWALL SonicPoints are wireless access points specially engineered to work with SonicWALL UTM appliances. Before you can manage SonicPoints in the management interface, perform the following steps: •Configuring Provisioning Profiles - page 19•Configuring a Wireless Zone - page 21•Configuring the Network Interface - page 22SonicPoint_N_GSG.book Page 18 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 19Configuring Provisioning ProfilesSonicPoint Profile defines settings that can be configured on a SonicPoint, such as radio SSIDs, and channels of operation. These profiles make it easy to apply basic settings to a wireless zone, especially when that zone contains multiple SonicPoints. When a SonicPoint is connected to a zone, it is automatically provisioned with the profile assigned to that zone. If a SonicPoint is connected to a zone that does not have a custom profile assigned to it, a default profile is used.To add a new profile:1. Navigate to the SonicPoint > SonicPoints page in the SonicOS interface.2. Click Add SonicPoint below the list of SonicPoint provisioning profiles. 3. The Add/Edit SonicPoint Profile window displays.Settings Tab1. Select Enable SonicPoint.2. Enter a Name Prefix to be used internally as the first part of the name for each SonicPoint provisioned.3. Select the Country Code for the area of operation.802.11n Radio Tab1. Select Enable Radio. 2. Optionally, select a schedule for the radio to be enabled from the drop-down list. The most common work and weekend hour schedules are pre-populated for selection.3. Select a Radio Mode to dictate the radio frequency band(s). The default setting is 2.4GHz 802.11n/g/b Mixed.4. Enter an SSID. This is the access point name that will appear in clients’ lists of available wireless connections.5. Select a Primary Channel and Secondary Channel. You may choose AutoChannel unless you have a reason to use or avoid specific channels.6. Under WEP/WPA Encryption, select the Authentication Type for your wireless network. SonicWALL recommends using WPA2 as the authentication type.7. Fill in the fields specific to the authentication type that you selected. The remaining fields change depending on the selected authentication type. SonicPoint_N_GSG.book Page 19 Friday, June 4, 2010 3:08 PM
Page 20 Configuring Wireless Access 8. Optionally, under ACL Enforcement, select Enable MAC Filter List to enforce Access Control by allowing or denying traffic from specific devices. Select a MAC address object group from the Allow List or Deny List to automatically allow or deny traffic to and from all devices with MAC addresses in the group. The Deny List is enforced before the Allow List. Advanced TabConfigure the advanced radio settings for the 802.11n radio. For most 802.11n advanced options, the default settings give optimum performance. For a full description of the fields on this tab, see the SonicOS Enhanced Administrator’s Guide.When you are finished, click OK.SonicPoint_N_GSG.book Page 20 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 21Configuring a Wireless Zone You can configure a wireless zone on the Network > Zones page. Typically, you will configure the WLAN zone for use with SonicPoints. To configure a standard WLAN zone: 1. On the Network > Zones page in the WLAN row, click the icon in the Configure column.2. Click on the General tab.3. Select the Allow Interface Trust setting to automate the creation of Access Rules to allow traffic to flow between the interfaces within the zone, regardless of which interfaces to which the zone is applied. For example, if the WLAN Zone has both the X2 and X3 interfaces assigned to it, selecting the Allow Interface Trust checkbox on the WLAN Zone creates the necessary Access Rules to allow hosts on these interfaces to communicate with each other.4. Select the checkboxes for the security services to enable on this zone. Typically, you would enable Gateway Anti-Virus, IPS, and Anti-Spyware. If your wireless clients are all running SonicWALL Client Anti-Virus, select Enable Client AV Enforcement Service.5. Click on the Wireless Tab.6. Select Only allow traffic generated by a SonicPoint to allow only traffic from SonicWALL SonicPoints to enter the WLAN Zone interface, providing maximum security. 7. Optionally, click the Guest Services tab to configure guest Internet access solely, or in tandem with secured access. For information about configuring Guest Services, see the SonicOS Enhanced Administrator’s Guide. 8. When finished, click OK.SonicPoint_N_GSG.book Page 21 Friday, June 4, 2010 3:08 PM
Page 22 Configuring the Network InterfaceEach SonicPoint or group of SonicPoints must be connected to a physical network interface that is configured for Wireless. SonicOS by default provides a standard wireless zone (WLAN), which can be applied to any available interface.To configure a network interface using the standard wireless (WLAN) zone:1. Navigate to the Network > Interfaces page and click the Configure button for the interface to which your SonicPoints will be connected.2. Select WLAN for the Zone type.3. Select Static for the IP Assignment.4. Enter a static IP Address in the field. Any private IP is appropriate for this field, as long at it does not interfere with the IP address range of any of your other interfaces. 5. Enter a Subnet Mask. In our example 255.255.255.0 is an appropriate mask.6. Optionally, choose a SonicPoint Limit for this interface. This option helps limit resources on port-by-port basis when using SonicPoints across multiple ports.7. Optionally, choose to allow Management and User Login mechanisms if they make sense in your deployment. Remember that allowing login from a wireless zone can pose a security threat, especially if you or your users have not set strong passwords.SonicPoint_N_GSG.book Page 22 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 235Setting Up Your SonicPointIn this Section:This section describes how to connect and configure physical aspects of the SonicPoint including cabling and mounting.•Installing Antennas (SonicPoint-Ne Only) - page 24•Connecting Ethernet Cable - page 24•Verifying Operation - page 28•Verifying WAN (Internet) Connectivity - page 28•Troubleshooting Tips - page 29•Onboard Help System - page 295SonicPoint_N_GSG.book Page 23 Friday, June 4, 2010 3:08 PM
Page 24 Installing Antennas (SonicPoint-Ne Only) Installing Antennas (SonicPoint-Ne Only)To install the SonicPoint-Ne included antennas:1. Remove the antennas from the bag and place one on each connector. 2. Carefully finger-tighten the fittings.3. Adjust the antennas for optimal reception.Note: For optimal wireless coverage in most cases, the SonicPoint-Ne antennas should be oriented vertically.The circular design of the SonicPoint aides in creating a strong tri-directional wireless signal pattern. In most cases, leaving the antennas straight up (as indicated in the illustration) will provide the best overall coverage.Note: The SonicPoint-Ne is authorized to use a dipole antenna with 4dBi or less. Only use antennas provided by SonicWALL; otherwise your authority to use this unit may be revoked. Be aware of the regulations in your region before using other antennas.Connecting Ethernet CableThe illustration on the following page depicts the SonicPoint within a typical network deployment.Ethernet Cabling: SonicPoint-Ne vs SonicPoint-NiWhile the SonicPoint-Ne may be powered with either the included external power adaptor or through Power over Ethernet (PoE), the SonicPoint-Ni must be powered using Power over Ethernet (PoE).Both SonicPoint appliances should be cabled with CAT5, CAT5e, or CAT6 Ethernet cabling. In addition, the SonicPoint-Ni will not function unless the Ethernet connection to its LAN port is powered either by using the SonicWALL PoE line injector (sold separately), or by using a third-party 802.3af compliant PoE powered switch. For more information on the SonicWALL PoE injector, visit:<http://www.sonicwall.com/us/products_solutions.html>SonicPoint_N_GSG.book Page 24 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 25Connecting the PoE CableIf your deployment uses a SonicWALL PoE injector, read and comply with instructions provided with the PoE first, then complete the following steps: 1. Plug the power cord of the SonicWALL PoE injector into the power outlet. 2. Using Ethernet cable (not included), connect the Data in port on the SonicWALL PoE Injector to the WLAN zone interface that you created earlier.3. Using Ethernet cable, connect the Data and Power out port on the SonicWALL PoE injector to the LAN port on the back of your SonicPoint.4. Wait for the link LED to illuminate. This indicates an active connection. It takes approximately one minute for the SonicWALL security appliance to auto-provision.WANWANNLAN/WLANLAN/WLANInternetRemote VPN UsersRemote ServersInternet (WAN)Local ClientsLocal ServersCDP Backup ApplianceLocal Network (LAN)Wireless ClientsWireless DevicesWireless (WLAN)Hotel / Home OceFront Lobby Sales MarketingX1 WANX0 LANX2 WLANPoE Injectoror PoE Switch(optional for SonicPoint Ne)linkwlanlanactlinkactSonicPoint_N_GSG.book Page 25 Friday, June 4, 2010 3:08 PM
Page 26 Mounting Using Ceiling Brackets Mounting Using Ceiling BracketsTo mount the SonicPoint to a crossbar between ceiling panels using included brackets:1. Using the 3/8” screws, screw in the brackets to the underside of the SonicPoint, making sure both brackets are parallel.2. (Optional) Attach the front LED/logo cover plate to the top of the SonicPoint and if necessary, rotate it to the desired position (See Mounting Using Anchor Screws section, on page 27 for illustration).3. Supporting the SonicPoint in one hand, clip the edge of each bracket over the edge of the ceiling crossbar. Make sure the SonicPoint is securely attached to the crossbar before releasing the device.Ceiling CrossbarMounting BracketsSonicPoint_N_GSG.book Page 26 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 27Mounting Using Anchor ScrewsTo mount the SonicPoint using included anchor screws: 1. On the mounting surface, mark the location to make two screw holes. The marks should be horizontally parallel to each other.2. Drill the holes to accommodate the metal anchor screws.3. Screw the anchor screws into the holes to their full depth. 4. Insert the 5/8” screws into the anchors, and screw them in deep enough to leave minimal space between the screw heads and the wall surface.5. (Optional) Attach the front LED/logo cover plate to the top of the SonicPoint and if necessary, rotate it to the desired position.6. Supporting the SonicPoint in your hands, securely fit the underside slots of the SonicPoint onto the screw heads.See also, Product Safety and Regulatory Information - page 37linkwlanlanactlinkactSonicPoint_N_GSG.book Page 27 Friday, June 4, 2010 3:08 PM
Page 28 Verifying Operation Verifying OperationTo verify that the SonicPoint is provisioned and operational, navigate to the SonicPoint > SonicPoints page in the SonicOS management interface. The SonicPoint displays an “operational” status in the SonicPoint table:Verifying WAN (Internet) ConnectivityComplete the following steps to confirm your Internet connectivity:1. Disconnect a client computer from any other network connections (LAN, 3G, and more). 2. Connect the client computer to the wireless access point by selecting the appropriate SSID.3. Launch your Web browser.4. Enter “http://www.sonicwall.com” in the address bar and press Enter on the keyboard. The SonicWALL website displays. If you are unable to browse to a website, see “Troubleshooting Tips” on page 29.SonicPoint_N_GSG.book Page 28 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 29Troubleshooting TipsIf the SonicPoint locates a peer SonicOS device, the two units perform an encrypted exchange and the profile assigned to the relevant wireless zone is used to automatically configure (provision) the newly added SonicPoint unit. Your SonicPoint is automatically included in the list on the Wireless > SonicPoints page of the management interface for the SonicWALL security appliance managing the SonicPoint. If it does not show in the list: •Make sure the SonicPoint is connected to an interface that is configured as part of a Wireless zone. Either the default WLAN zone, or a custom zone with type set to “wireless” is required.•Click the Synchronize SonicPoints button. This is located in the SonicOS management interface on the SonicPoint > SonicPoints page and forces the SonicWALL appliance, if connected, to download a new SonicPoint image from the SonicWALL back-end server.•Ensure that the SonicPoint is connected to a 802.3af compliant PoE powered Ethernet connection. If using PoE to power your SonicPoint appliance, keep in mind that a PoE-capable switch or PoE injector is required.•Verify that your PoE switch/injector is rated to deliver at least 15 watts of power to each port. Some older PoE devices do not provide sufficient power to properly run current generation 802.11n devices across multiple ports. Check with your PoE manufacturer for 802.3af support, or use a SonicWALL PoE injector.Onboard Help SystemAll SonicWALL network security appliances include an onboard help system with help topics that are relevant to each area of the management interface. To access SonicPoint help, click the Help icon in the upper right-hand corner of the SonicOS management interface while you are on a SonicPoint page.SonicPoint_N_GSG.book Page 29 Friday, June 4, 2010 3:08 PM
Page 30 SonicPoint_N_GSG.book Page 30 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 316Support and Training OptionsIn this Section:This section provides overviews of customer support and training options for SonicWALL appliances.•Customer Support - page 32•Knowledge Base - page 32•User Forums - page 33•Training - page 34•Related Documentation - page 35•SonicWALL Secure Wireless Network Integrated Solutions Guide - page 366SonicPoint_N_GSG.book Page 31 Friday, June 4, 2010 3:08 PM
Page 32 Customer Support Customer SupportSonicWALL offers telephone, email and Web-based support to customers who have a valid Warranty or who purchased a Support Contract. Please review our Warranty Support Policy for product coverage. SonicWALL also offers a full range of consulting services to meet your needs, from our innovative implementation services to traditional statement of work-based services.For further information, visit: <http://www.sonicwall.com/us/support.html>Knowledge BaseThe Knowledge Base allows users to search for SonicWALL documents based on the following types of search tools:• Browse• Search for keywords• Full-text searchFor further information, navigate to the Support > Knowledge Portal page at: <http://www.mysonicwall.com/>SonicPoint_N_GSG.book Page 32 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 33User ForumsThe SonicWALL User Forums are a resource that provide users the ability to communicate and discuss a variety of security and appliance subject matters. The following categories are available for users:• Content Security Manager topics • Continuous Data Protection topics • Email Security topics • Firewall topics • Network Anti-Virus topics • Security Services and Content Filtering topics • SonicWALL GMS and Viewpoint topics • SonicPoint and Wireless topics • SSL VPN topics • TZ 210 / Wireless WAN - 3G Capability topics• VPN Client topics • VPN site-to-site and interoperability topics For further information, visit:<https://forum.sonicwall.com/>SonicPoint_N_GSG.book Page 33 Friday, June 4, 2010 3:08 PM
Page 34 Training TrainingSonicWALL offers an extensive sales and technical training curriculum for Network Administrators, Security Experts, and SonicWALL Medallion Partners who need to enhance their knowledge and maximize their investment in SonicWALL Products and Security Applications. SonicWALL Training provides the following resources for its customers:• E-Training• Instructor-Led Training• Custom Training• Technical Certification• Authorized Training PartnersFor further information, visit:<http://training.sonicwall.com/>SonicPoint_N_GSG.book Page 34 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 35Related DocumentationSee the following related documents for more information:• SonicOS Enhanced Administrator’s Guide• SonicOS Enhanced Release Notes• SonicOS Enhanced Feature Modules• DPI-SSL• MAC-IP Anti-Spoof• Virtual Access Points• SSL VPN Remote Access• High Availability• Multiple Administrators• NAT Load Balancing• Packet Capture• Radio Frequency Monitoring• Single Sign-On• SSL Control• Secure Wireless Bridging• SonicWALL GMS Administrator’s Guide• SonicWALL GVC Administrator’s Guide• SonicWALL ViewPoint Administrator’s Guide• SonicWALL GAV Administrator’s Guide• SonicWALL IPS Administrator’s Guide• SonicWALL Anti-Spyware Administrator’s Guide• SonicWALL CFS Administrator’s GuideFor further information, visit: <http://www.sonicwall.com/us/support.html>SonicPoint_N_GSG.book Page 35 Friday, June 4, 2010 3:08 PM
Page 36 SonicWALL Secure Wireless Network Integrated Solutions Guide SonicWALL Secure Wireless Network Integrated Solutions GuideLooking to go wireless? Have questions about what it takes to build a truly “secure” wireless network? Check out the SonicWALL Secure Wireless Network Integrated Solutions Guide. This book is the official guide to SonicWALL’s market-leading wireless networking and security devices. This title is available in hardcopy at fine book retailers everywhere, or by ordering directly from Elsevier Publishing at:<http://www.elsevier.com>SonicPoint_N_GSG.book Page 36 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 377Product Safety and Regulatory InformationIn this Section:This section provides regulatory, trademark, and copyright information.•Safety and Regulatory Information for the SonicWALL SonicPoint Wireless Appliance - page 38•SonicWALL SonicPoint Wireless Appliance Sicherheit und gesetzliche Vorschriften - page 39•FCC Part 15 Class B Notice for the SonicWALL SonicPoint Wireless Appliance - page 40•Copyright Notice - page 43•Trademarks - page 437SonicPoint_N_GSG.book Page 37 Friday, June 4, 2010 3:08 PM
Page 38 Safety and Regulatory Information for the SonicWALL SonicPoint Wireless Appliance Safety and Regulatory Information for the SonicWALL SonicPoint Wireless ApplianceMounting the SonicWALL•Mount in a location away from direct sunlight and sources of heat. A maximum ambient temperature of 104º F (40º C) is recommended.•Route cables away from power lines, fluorescent lighting fixtures, and sources of noise such as radios, transmitters, and broadband amplifiers•The included power cord is intended for use in North America only. For European Union (EU) customers, a power cord is not included.• Ensure that no water or excessive moisture can enter the unit.•Allow unrestricted airflow around the unit and through the vents on the side of the unit. A minimum of 1 inch (25.44mm) clearance is recommended.•Consideration must be given to the connection of the equipment to the supply circuit and the effect of over-loading the circuits has minimal impact on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings must be used when addressing this concern.Cable ConnectionsAll Ethernet and RS232 (Console) cables are designed for intra-building connection to other equipment. Do not connect these ports directly to communication wiring or other wiring that exits the building where the SonicWALL is located. Power Supply Information for APL21-083If the power supply is missing from your SonicWALL product package, please contact SonicWALL Technical Support at 408-752-7819 for a replacement. This product should only be used with a UL listed power supply marked “Class 2” or “LPS”, with an output rated 48 VDC, minimum 0.35 A.Power Supply Information APL21-06EIf the power supply is missing from your SonicWALL productpackage, please contact SonicWALL Technical Support at 408-752-7819 for a replacement. This product should only be usedwith a UL listed power supply marked “Class 2” or “LPS”, with anoutput rated 12 VDC, minimum 1.5 A.If power is provided by the Ethernet cable plugged into the "lan" port, this is called "Power Over Ethernet" or "POE". The POE source should only be UL listed marked “Class 2” or “LPS”, with an output rated 48 VDC, minimum 0.35 A. Regulatory Model/Type Product NamesAPL21-06EAPL21-083SonicPoint-NeSonicPoint-NiSonicPoint_N_GSG.book Page 38 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 39SonicWALL SonicPoint Wireless Appliance Sicherheit und gesetzliche VorschriftenWeitere Hinweise zur Montage•Wählen Sie für die Montage einen Ort, der keinem direkten Sonnenlicht ausgesetzt ist und sich nicht in der Nähe von Wärmequellen befindet. Die Umgebungstemperatur darf nicht mehr als 40 °C betragen.•Führen Sie die Kabel nicht entlang von Stromleitungen, Leuchtstoffröhren und Störquellen wie Funksendern oder Breitbandverstärkern.•Das beigefügte Netzkabel ist nur für den Betrieb in Nordamerika vergesehen. Für Kunden in der Europäischen Union ist kein Kabel beigefügt.•Stellen Sie sicher, dass das Gerät vor Wasser und hoher Luftfeuchtigkeit geschützt ist.•Stellen Sie sicher, dass die Luft um das Gerät herum zirkulieren kann und die Lüftungsschlitze an der Seite des Gehäuses frei sind. Hier ist ein Belüftungsabstand von mindestens 26 mm einzuhalten.• Vergewissern Sie sich, dass das Gerät sicher im Rack befestigt ist. KabelverbindungenAlle Ethernet- und RS232-C-Kabel eignen sich für die Verbindung von Geräten in Innenräumen. Schließen Sie an die Anschlüsse der SonicWALL keine Kabel an, die aus dem Gebäude herausgeführt werden, in dem sich das Gerät befindet.Informationen zur Stromversorgung APL21-083Sollte das Netzteil nicht im Lieferumfang der SonicWALL enthalten sein, wenden Sie sich diesbezüglich an den technischen Support von SonicWALL (Tel.: +1-408-752-7819). Dieses Produkt darf nur in Verbindung mit einem nach den Normen der Underwriter Laboratories, USA als „UL-gelistet“ zugelassenen Netzteil der Kategorie „Class 2“ oder „LPS“ verwendet werden. Ausgang: 48 VDC Gleichsspannung, mind. 0,35 A.Informationen zur Stromversorgung APL21-06ESollte das Netzteil nicht im Lieferumfang der SonicWALLenthalten sein, wenden Sie sich diesbezüglich an dentechnischen Support von SonicWALL (Tel.: +1-408-752-7819). Dieses Produkt darf nur in Verbindung mit einem nach denNormen der Underwriter Laboratories, USA als „UL-gelistet“zugelassenen Netzteil der Kategorie „Class 2“ oder „LPS“verwendet werden. Ausgang: 12 VDC Gleichsspannung, mind. 1,5 A.Wenn der Strom über den LAN Port eingespeist wird, bezeichnet man dies als "Power over Ethernet" oder "PoE". Die POE Quelle sollte mit UL Listed “Class 2” oder "LPS" gekennzeichnet sein, mit einer Ausgangsspannung von 48 VDC und mindestens 0.35 ASonicPoint_N_GSG.book Page 39 Friday, June 4, 2010 3:08 PM
Page 40 FCC Part 15 Class B Notice for the SonicWALL SonicPoint Wireless Appliance FCC Part 15 Class B Notice for the SonicWALL SonicPoint Wireless ApplianceNOTE: This equipment was tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. And, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference using one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and the receiver.• Connect the equipment into an outlet on a circuit different from the receiver connection.• Consult SonicWALL for assistance.Complies with EN55022 Class B and CISPR22 Class B.*Refer to the label on the bottom of the unit for device information including Class A or Class B FCC information.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.FCC and IC RF Radiation Exposure StatementThis equipment complies with FCC and IC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters (7.9 inches) between the radiator (antenna) and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For more information regarding the above statement, please contact SonicWALL, Inc. at:2001 Logic DriveSan Jose, CA95124-34521-408-745-9600North American Authorized ChannelsSonicWALL declares that the APL21-083 (FCC ID: QWU-083)(IC: 4408A-083) and APL21-06E (FCC ID: QWU-06E)(IC: 4408A-06E) when sold in US or Canada is limited to CH1~CH11 byspecified firmware controlled in the USA.Canadian Radio Frequency Emissions StatementThis Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.Industry Canada StatementThis device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:FCC and IC(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Caution:The device for the band 5470 -5725 MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile satellite systems. The APL21-06E device has been designed to operate with an antenna having a maximum gain of 4 dBm. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.SonicPoint_N_GSG.book Page 40 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 41This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies.In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services.This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France.Declaration of ConformityCertificate #: EU00170-AI, the undersigned, hereby declare that the equipment specified above conforms to the above Directives and Standards. Quality control procedures will ensure series production of equipment will be compliant.Application of council Directive2004/108/EC (EMC) 2006/95/EC (LVD)1999/5/EC (R&TTE)Standard(s) to which conformity is declaredEN 55022:1998 +A1 +A2 Class BEN 55024:1998, +A2EN 61000-3-2:2000, +A2EN 61000-3-3:1995, +A2EN 60950-1:2006, +A11:2009National Deviations: AR, AT, AU, BE, CA, CH,CN, CZ, DE, DK, FI, FR, GB, GR, HU, IL, IN, IT,JP, KE, KR, MY, NL, NO, PL, SE, SG, SI, SK, USEN 300 328 V1.7.1:2006EN 301 893 V1.5.1:2008EN 301 489 V1.8.1:2008EN 301 489-17 V2.1.1:2009aEN 50385:2002Manufacturer/Responsible PartySonicWALL, Inc.2001 Logic DriveSan Jose, California 95124-3452 USAType of Equipment 802.11b/g/n access pointType Numbers APL21-06EAPL21-083May be Marketed as SonicPoint-NeSonicPoint-NiSignature /s/ Larry Wagner_________ Sr. Engineering Director Date 05/30/10SonicPoint_N_GSG.book Page 41 Friday, June 4, 2010 3:08 PM• 第十二條 •經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用 者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 •第十四條 •低功率射頻電機之使用不得影響飛航安全及干擾合法通信； 經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機 須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 依LP0002第4.7.5節規定 ”在5.25-5.35󲥿赫頻帶內操作之無線資訊 傳輸設備，限於室內使用” 專業安裝警語(固定式點對點操作) 此器材須經專業安裝並限用於固定式點對點操作
Page 42 FCC Part 15 Class B Notice for the SonicWALL SonicPoint Wireless Appliance SonicWALL tímto prohlašuje, že tento APL21-083 / APL21-06E je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.Undertegnede SonicWALL erklærer herved, at følgende udstyr APL21-083 / APL21-06E overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.Hiermit erklärt SonicWALL, dass sich das Gerät APL21-083 / APL21-06E in Übereinstim-mung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG bendet. Käesolevaga kinnitab SonicWALL seadme APL21-083 / APL21-06E vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.Hereby, SonicWALL, declares that this APL21-083 / APL21-06E is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.Por medio de la presente SonicWALL declara que el APL21-083 / APL21-06E cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ SonicWALL ΔΗΛΩΝΕΙ ΟΤΙ APL21-083 / APL21-06E ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.Par la présente SonicWALL déclare que l'appareil APL21-083 / APL21-06E est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.Con la presente SonicWALL dichiara che questo APL21-083 / APL21-06E è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.Ar šo SonicWALL deklarē, ka APL21-083 / APL21-06E atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.Šiuo SonicWALL deklaruoja, kad šis APL21-083 / APL21-06E atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.Hierbij verklaart SonicWALL dat het toestel APL21-083 / APL21-06E in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.Hawnhekk, SonicWALL, jiddikjara li dan APL21-083 / APL21-06E jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm d-Dirrettiva 1999/5/EC.Alulírott, SonicWALL nyilatkozom, hogy a APL21-083 / APL21-06E megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.Niniejszym SonicWALL oświadcza, że APL21-083 / APL21-06E jest zgodny z zasadnic-zymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.SonicWALL declara que este APL21-083 / APL21-06E está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.SonicWALL izjavlja, da je ta APL21-083 / APL21-06E v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.SonicWALL týmto vyhlasuje, že APL21-083 / APL21-06E spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.SonicWALL vakuuttaa täten että APL21-083 / APL21-06E tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.Härmed intygar SonicWALL att denna APL21-083 / APL21-06E står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.SonicPoint_N_GSG.book Page 42 Friday, June 4, 2010 3:08 PM
SonicWALL SonicPoint Getting Started Guide Page 43Copyright Notice© 2010 SonicWALL, Inc.All rights reserved.Under the copyright laws, this manual or the software described within, cannot be copied, in whole or part, without the written consent of the manufacturer, except in the normal use of the software to make a backup copy. The same proprietary and copyright notices must be affixed to any permitted copies as were affixed to the original. This exception does not allow copies to be made for others, whether or not sold, but all of the material purchased (with all backup copies) can be sold, given, or loaned to another person. Under the law, copying includes translating into another language or format.Specifications and descriptions subject to change without notice.TrademarksSonicWALL is a registered trademark of SonicWALL, Inc.Microsoft Windows, Windows Vista, Windows XP, Windows Server, Internet Explorer, and Active Directory are trademarks or registered trademarks of Microsoft Corporation.Other product and company names mentioned herein may be trademarks and/or registered trademarks of their respective companies and are the sole property of their respective manufacturers.SonicPoint_N_GSG.book Page 43 Friday, June 4, 2010 3:08 PM
Page 44 Trademarks SonicPoint_N_GSG.book Page 44 Friday, June 4, 2010 3:08 PM
SonicWALL, Inc.2001 Logic Drive T +1 408.745.9 60 0 w ww. son icwa ll.com San Jose CA 95124-3452 F +1 408.745.9300P/N 232-001795-50 Rev A 06/10©2010 SonicWALL, Inc. is a registered trademark of SonicWALL, Inc. Other product names mentioned herein may be trademarks and/or registered trademarks of their respective companies. Specifications and descriptions subject to change without notice. SonicPoint_N_GSG.book Page 45 Friday, June 4, 2010 3:08 PM

Navigation menu